How long does firmware take to inst

How long does firmware for the Nomad JUkebox Zen Xtra take to install approximately? It has been going for about a half hour and i'm wondering if that is a problem. it is 60 gigs
thanks!!
tim

Only a minute or two on the Xtra as well.
If the process has stalled then all you can do is leave it for as long as possible to see if it recovers, and then disconnect the player to see if the firmware has taken. A partially written firmware is the biggest problem as it will most likely leave the player in a non-functional state.

Similar Messages

C3-00::How Long Does It Take To Upgrade Firmware.....

Hi
I am want to upgrade my nokia c3-00 firmware from 04.60 to 08.70 through PC via Usb cable...
How long does it take to upgrade,It moves to 5 MIUTES REMAINING and stucks there for hours...
I m upgading it first time...Please tell how much time it takes??

With a Broadband connection, it should not take more than 30-35 minutes..
Check thru' NSU ...

How long does it take to restore firmware.My phone has been in recovery for 3 hours now?

How long does it take to restore firmware on iphone5.The phone is only 3 week old and has been in recovery mode for nearly 3 hours now?

- No. That is too long. What does the status bar in iTunes say the iPod is doing?
- Terminate the sync. Force close iTunes if necessary then reboot the computer. Also reset the iPod. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Try again. If still problem come back with what the status bar says when it stopped.

Sick of interleaving - how long does DLM take

Have had problems with a dishwasher tripping our electric over the past month and this has of course caused DLM to kick in any put interleave on line and limit my IP profile to always be below 60 mb. My data rate is currently 57957 and hasn't increased for the past month steadily dropping from the 60mb ip cap last month when power cuts happened.
Before my connection was working great and my data rate was a lot closer to the Max data rate, currently it is at 57957, Max at 65760. The Max data rate has been as high as 69000, still no increase in IP data rate.
The main thing though is interleaveing, I know that this is controlled by DLm and cannot be turned of directly, but as my IP profile seems to be stuck and steadily decreasing on every connection restart (which the hh5 seems to do on a whim sometimes)
My line stats seem to be ok SNR 6.0\6.0
Line attenuation 18.2
Please can my IP profile be reset to remove my IP cap which would hopefully put me back on fastpath which I had been on for months and months till the power cuts

same as mine https://community.bt.com/t5/BT-Infinity-Speed-Connection/Poor-Service-from-BT-adamant-about-problem/...
Please can a mod look at my connection just reset the IP profile please, there are no faults on my line!!!!!!!!!
Re: Poor Service from BT, adamant about problem!
Options
on ‎28-07-2014 1h09
I feel this is the exact problem I've been having posted on here titled sick of interleaving - how long till DLM turns it off.
Could you check if your 1st hop is around 12 ms (click start, run, cmd, enter, tracert www.BBC.co.uk) my guess would be interleaving has been put on your line too.
If your router resets too many times (mine due to faulty dishwasher tripping electric)
Once this is on it seems to take ages to reset back to normal. Like you I have the hh5 and this will sometimes do a random disconnect (firmware bug or BT messing with connection?) I always see in my event log a cwmp login from bt which will then reboot the router.
Like you my attenuation is very short (18.2) SNR At 6.2 but it seems because my hh5 sometimes just reboots connection ( usually around 2.20am going from event logs) that interleaving will never come off. I have read that it takes 2 weeks constant connection for speeds to return to normal and interleaving to be turned off.
Not happy about my connection for last month, after being very happy for months and months. As soon as DLM has kicked can feel difference especially in pings more than raw speed for me.
Will run down my contract and jump ship as soon as contract runs out if mine doesn't improve.
Message 19 of 20 (7 Views)
Posted from my mobile
Add Tag...
Quick ReplyReply
smoke999
Visitor
Posts: 4
Registered: ‎26-07-2014
0
Re: Poor Service from BT, adamant about problem!
Options
on ‎28-07-2014 1h17
https://community.bt.com/t5/BT-Infinity-Speed-Connection/sick-of-interleaving-how-long-does-DLM-take...
Is this the BT backdoor to manange connection?
(172830.560000) CWMP: session completed successfully
22:05:05, 27 Jul.
(172830.320000) CWMP: HTTP authentication success from https://pbthdm.bt.mo
22:05:01, 27 Jul.
(172826.800000) CWMP: Server URL: https://pbthdm.bt.mo; Connecting as user: ACS username
22:05:01, 27 Jul.
(172826.790000) CWMP: Session start now. Event code(s): '2 PERIODIC,4 VALUE CHANGE'
22:05:01, 27 Jul.
(172826.590000) CWMP: Initializing transaction for event code 2 PERIODIC

How long does it take to create a recovery disc?

Hi!!!
I have just bought a Toshiba Portege T110.
I tried the first time round and cancelled at disc 4 bec i was out of writeable disc.
Today i am on my 2nd try. I have mgt disc 1-3. When at disc 4~~it says is creating Windon Recovery Environment (64bit) and recording. But the progress bar has been hanging there for the abt 1-2hrs and still not done yet~~
I tried to cancel the program, but it says is recording and advise me not to cancel as it will take a long time.
Can some kind soul advise if this is normal? How long does it takes? If not, what could be the problem?
Thank you in advance!!!

Hi all~~
i have the answer to my question alrdy~~
i accidentatly canceled the copying after waiting over 2 hr on disc 4~~
I restarted the process this morning~~~as i have alrdy done disc 1-3~~i am able to start at disc 4 straight away!!!
Disc 4 took less then 10 mins to complete.
So guys~~ the whole process from disc 1 to 4 takes less than 1 hr.
All the best to you guys!!
And Merry Christmas!!

"How long does it take to do a dist-upgrade on your distro?"

Yesterday there was a question in the USALUG.org "How long does it take to do a dist-upgrade on your distro?"
This question was a good question, so I decide to make the ultimate test. I have a lot of computers standing here around, and remembered that on one of them was have already Archlinux installation. I was right, when I booted, the system check said me, that the system was 253 days not checked anymore. I got so excited that I forgot to check was it one of my 0.7.2 Gimmick or 0.8 Voodoo installations.
The Computer
Dell OptiPlex GX110
[jada@arch-02 ~]$ cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 797.452
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat p se36 mmx fxsr sse up
bogomips : 1596.45
clflush size : 32
[jada@arch-02 ~]$
I used the following command for the update
$ time pacman -Syu
The Test
first update pacman
[root@arch-02 jada]# pacman -Syu
warning: current locale is invalid; using default "C" locale
:: Synchronizing package databases...
core 23.8K 80.0K/s 00:00:00 [#####################] 100%
extra 310.5K 292.3K/s 00:00:01 [#####################] 100%
community 341.0K 295.8K/s 00:00:01 [#####################] 100%
:: Starting full system upgrade...
:: Replace mktemp with core/coreutils? [Y/n] y
:: Replace mpg321 with extra/mpg123? [Y/n] y
warning: bind: forcing upgrade to version 9.4.2-1
warning: cpufrequtils: forcing upgrade to version 002-3
warning: dnsutils: forcing upgrade to version 9.4.2-1
warning: flex: forcing upgrade to version 2.5.33-4
warning: opera: forcing upgrade to version 9.25-2
:: pacman has detected a newer version of the "pacman" package.
:: It is recommended that you allow pacman to upgrade itself
:: first, then you can re-run the operation with the newer version.
:: Upgrade pacman first? [Y/n] y
resolving dependencies... done.
looking for inter-conflicts... done.
Targets: libarchive-2.4.11-1 libdownload-1.3-1 pacman-3.1.1-1
Total Package Size: 1.19 MB
Proceed with installation? [Y/n] y
:: Retrieving packages from core...
libarchive 314.8K 253.4K/s 00:00:01 [#####################] 100%
libdownload 49.4K 97.9K/s 00:00:01 [#####################] 100%
pacman 855.2K 460.4K/s 00:00:02 [#####################] 100%
checking package integrity... done.
cleaning up... done.
(3/3) checking for file conflicts [#####################] 100%
(1/3) upgrading libarchive [#####################] 100%
(2/3) upgrading libdownload [#####################] 100%
(3/3) upgrading pacman [#####################] 100%
>>> The makepkg.conf syntax has changed, please note the new format
>>> when merging the pacnew file with your old configuration.
>>>
>>> The pacman.conf default file has changed. Please update your
>>> config to use the single mirrorlist, and any additional files
>>> in /etc/pacman.d/ (core, extra, etc.) can be deleted.
>>>
>>> The location of sync DBs has moved from /var/lib/pacman/ to
>>> /var/lib/pacman/sync/ for several reasons. To delete older
>>> DBs, please run pacman -Sc and follow the instructions.
>>> You will also have to run pacman -Sy to refresh the sync DBs.
>>>
>>> abs is no longer included; please install the 'abs' package
>>> to use abs. You may need to edit abs.conf to re-enable repos.
[root@arch-02 jada]#
restart pacman 3.1.1 and update the packages
[root@arch-02 jada]# time pacman -Syu
:: Synchronizing package databases...
core 23.8K 80.3K/s 00:00:00 [#####################] 100%
extra 310.5K 261.1K/s 00:00:01 [#####################] 100%
community 341.0K 302.5K/s 00:00:01 [#####################] 100%
:: Starting full system upgrade...
:: Replace mktemp with core/coreutils? [Y/n] y
:: Replace mpg321 with extra/mpg123? [Y/n] y
warning: bind: forcing upgrade to version 9.4.2-1
warning: cpufrequtils: forcing upgrade to version 002-3
warning: dnsutils: forcing upgrade to version 9.4.2-1
warning: flex: forcing upgrade to version 2.5.33-4
warning: opera: forcing upgrade to version 9.25-2
resolving dependencies...
warning: dependency cycle detected:
warning: bash will be installed before its glibc dependency
warning: dependency cycle detected:
warning: readline will be installed before its glibc dependency
warning: dependency cycle detected:
warning: ncurses will be installed before its glibc dependency
warning: dependency cycle detected:
warning: db will be installed before its coreutils dependency
looking for inter-conflicts...
Remove: mktemp mpg321
Total Removed Size: 0.08 MB
Targets: ncurses-5.6-6 readline-5.2-7 bash-3.2.033-2
kernel-headers-2.6.23.1-2 tzdata-2007k-1 glibc-2.7-7 attr-2.4.39-2
acl-2.2.45-2 cracklib-2.8.10-5 gcc-libs-4.2.3-3 db-4.6.21-2
pam-0.99.9.0-2 shadow-4.0.18.2-2 coreutils-6.10-2 libtool-1.5.26-1
mpg123-1.2.0-1 fontconfig-2.5.0-1 zlib-1.2.3-4 libpng-1.2.24-1
cairo-1.4.14-1 libtasn1-1.3-1 lzo2-2.02-3 libgpg-error-1.6-1
libgcrypt-1.4.0-1.1 opencdk-0.6.6-1 gnutls-2.0.4-1 libcups-1.3.5-1
pcre-7.6-2 glib2-2.14.5-1 pango-1.18.4-1 gtk2-2.12.7-1
binutils-2.18-5 gmp-4.2.2-2 mpfr-2.3.1-1 gcc-4.2.3-1
glproto-1.4.9-1 libgl-7.0.3rc1-1 mesa-7.0.3rc1-1 acroread-8.1.2-1
dialog-1.1_20071028-1 pciutils-2.2.8-3 alsa-utils-1.0.15-2
e2fsprogs-1.40.4-1 apr-1.2.12-1 gdbm-1.8.3-5 apr-util-1.2.12-1
openssl-0.9.8g-2 apache-2.2.8-1 jack-audio-connection-kit-0.109.0-1
kde-common-3.5.8-3 libxmu-1.0.4-1 qt3-3.3.8-6.1 arts-1.5.8-2
diffutils-2.8.1-5 gawk-3.1.6-2 m4-1.4.10-3 autoconf-2.61-3
perl-5.8.8-9 automake-1.10.1-2 filesystem-2007.11-6 avahi-0.6.20-3
bftpd-2.1-1 bin86-0.16.17-3 dnsutils-9.4.2-1 bind-9.4.2-1
bison-2.3-4 bluez-libs-3.24-1 libusb-0.1.12-3 bluez-utils-3.24-2
bridge-utils-1.2-2 bzip2-1.0.4-3 cairomm-1.4.6-1 cmake-2.4.8-1
cpio-2.9-3 sysfsutils-2.1.0-4 cpufrequtils-002-3
device-mapper-1.02.24-1 popt-1.10.6-3 cryptsetup-1.0.5-5
csup-20060318-5 cups-1.3.5-1 curl-7.18.0-1 dbus-qt3-0.62-3
dcron-3.2-3 dhcpcd-3.2.0-1 dmapi-2.2.8-3 libxml2-2.6.31-1
docbook-xsl-1.73.2-1 dosfstools-2.11-2 dvd+rw-tools-7.0-4 ed-0.8-3
enlightenment-0.16.8.11-1 gnome-desktop-2.20.3-1 eog-2.20.4-1
libidl2-0.8.10-1 mozilla-common-1.1-2 xulrunner-1.8.1.11-1
epiphany-2.20.3-1 eventlog-0.2.5-2 ghostscript-8.61-1
gnome-keyring-2.20.3-1 libsasl-2.1.22-5 libldap-2.3.39-2
smbclient-3.0.28A-1 gnome-vfs-2.20.1-1 libdjvu-3.5.20-1
poppler-0.6.3-1 poppler-glib-0.6.3-1 evince-2.20.2-1 evms-2.5.5-5
libsoup-2.2.104-1 evolution-data-server-1.12.3-1 exiv2-0.15-1
faad2-2.6-1 grep-2.5.3-3 sed-4.1.5-3 fakeroot-1.9.2-1 fbset-2.1-2
file-4.23-1 file-roller-2.20.3-1 findutils-4.2.32-1
firefox-2.0.0.12-1 flashplugin-9.0.115.0-2 flex-2.5.33-4
font-bitstream-speedo-1.0.0-4 font-misc-ethiopic-1.0.0-4
font-misc-meltho-1.0.0-4 freeglut-2.4.0-3 freetype1-1.3.1-4
glib-1.2.10-7 gtk-1.2.10-8 imlib-1.9.15-4 libstroke-0.5.1-2
fvwm-2.4.20-2 gail-1.20.2-1 gc-7.0-2 gdb-6.7.1-1
gtksourceview2-2.0.2-1 libgnomecups-0.2.3-1 libgnomeprint-2.18.3-1
libgnomeprintui-2.18.2-1 python-2.5.1-5 pygobject-2.14.1-1
pygtk-2.12.1-1 gedit-2.20.4-1 gen-init-cpio-2.6.17-3
gettext-0.17-1 librsvg-2.20.0-1 gimp-2.4.4-1 gkrellm-2.3.1-2
glibmm-2.14.2-1 gmime-2.2.16-1 gnokii-0.6.22-3
gnome-menus-2.20.3-1 libwnck-2.20.3-1 gnome-panel-2.20.3-1
gstreamer0.10-0.10.15-1 gstreamer0.10-base-0.10.15-1
gstreamer0.10-alsa-0.10.15-1 gucharmap-1.10.2-1 libgtop-2.20.1-1
gnome-applets-2.20.1-1 metacity-2.20.2-1 libbeagle-0.3.0-3
nautilus-2.20.0-4 gnome-control-center-2.20.3-1
gnome-python-2.20.1-1 gnome-python-desktop-2.20.0-3 guile-1.8.3-1
gnome-games-2.20.3-1 gnome-power-manager-2.20.2-1
tcp_wrappers-7.6-8 gnome-session-2.20.3-1 gtkmm-2.12.3-1
gnome-system-monitor-2.20.2-1 vte-0.16.12-1 gnome-terminal-2.18.4-1
gnome-utils-2.20.0.1-2 gnupg-1.4.8-1 libassuan-1.0.4-1
gnupg2-2.0.8-1 gpgme-1.1.6-1 gpm-1.20.1-7 groff-1.19.2-4
grub-0.97-9 gstreamer0.10-cdparanoia-0.10.15-1
gstreamer0.10-gnomevfs-0.10.15-1 gstreamer0.10-ogg-0.10.15-1
gstreamer0.10-vorbis-0.10.15-1 gtkhtml-3.16.3-1 gutenprint-5.0.2-1
vi-7.1.228-1 vim-7.1.228-1 gvim-7.1.228-1 gzip-1.3.12-4
hal-info-0.20071212-1 hdparm-7.7-3 usbutils-0.73-5 wget-1.11-1
hwd-5.3.2-1 hwdetect-0.9-1 icewm-1.2.35-1 ifenslave-1.1.0-3
imagemagick-6.3.8.0-1 intltool-0.37.0-1 iproute-070710-3
iptables-1.3.8-2 iputils-20070202-4 isdn4k-utils-3.2p1-3
jfsutils-1.1.12-2 jre-6u3-2 kbd-1.12.20070827-2 kdelibs-3.5.8-4
lm_sensors-3.0.1-1 xorg-xauth-1.0.2-1 kdebase-3.5.8-3
qscintilla-qt3-1.7.1-2 kdebindings-3.5.8-2 libgphoto2-2.4.0-4
poppler-qt3-0.6.3-1 kdegraphics-3.5.8-3 sqlite3-3.5.6-1
libopensync-0.34-1 kdepim-3.5.8-2 klibc-1.5-3 klibc-extras-2.3-1
klibc-udev-116-2 klibc-module-init-tools-3.2.2-1
mkinitcpio-0.5.17-2 module-init-tools-3.2.2-5 kernel26-2.6.24.1-2
less-418-1 lftp-3.6.3-1 libao-0.8.8-2 orbit2-2.14.12-1
libbonobo-2.20.3-1 libcdio-0.79-1 libelf-0.8.10-3 libevent-1.3d-2
libgdiplus-1.2.6-1 libmikmod-3.1.12-1 libmysqlclient-5.0.51-2
libpcap-0.9.8-2 libsamplerate-0.1.2-4 libtar-1.2.11-3
libxfont-1.3.1-2 licenses-2.3-1 lilo-22.8-2 links-2.1pre33-1
logrotate-3.7.5-1 lua-5.1.3-1 lvm2-2.02.33-1 mailx-8.1.1-5
make-3.81-3 man-1.6f-2 man-pages-2.77-1 mdadm-2.6.4-1
mono-1.2.6-1 mutt-1.5.17-4 mysql-clients-5.0.51-3 mysql-5.0.51-3
nano-2.0.7-1 net-tools-1.60-13 netkit-ftp-0.17-4
netkit-telnet-0.17-7 nfsidmap-0.20-2 portmap-6.0-2
nfs-utils-1.1.0-3 ngrep-1.45-4 nmap-4.53-1 ntp-4.2.4p4-4
openssh-4.7p1-6 openvpn-2.0.9-3 opera-9.25-2 orca-2.20.3-1
patch-2.5.4-4 pcmciautils-014-3 php-5.2.5-3 pilot-link-0.12.3-1
pine-4.64-4 pkgconfig-0.22-3 procps-3.2.7-4 libx86-0.99-1
vbetool-1.0-2 pm-utils-0.99.4-1 qt-4.3.3-4 poppler-qt-0.6.3-1
postgresql-libs-8.2.6-1 postgresql-8.2.6-1 ppp-2.4.4-6
procinfo-19-2 psmisc-22.6-1 qca-2.0.0.svn744387-1.1 qca-qt3-1.0-1
qca-tls-1.0-5 qscintilla-2.1-3 reiserfsprogs-3.6.20-3
rp-pppoe-3.8-2 rsync-2.6.9-4 samba-3.0.28A-1 screen-4.0.3-5
seahorse-2.20.3-1 shared-mime-info-0.23-1 sudo-1.6.9p12-1
sysklogd-1.5-1 syslog-ng-2.0.6-1 util-linux-ng-2.13.0.1-2
sysvinit-2.86-4 taglib-1.4.0.svn744384-1 tar-1.19-2 tcl-8.5.1-1
tcpdump-3.9.8-1 tcsh-6.15.01-1 thunderbird-2.0.0.9-2 tk-8.5.1-1
totem-plparser-2.21.91-1 totem-2.20.1-3 ttf-dejavu-2.23-1
udev-116-3 unichrome-dri-7.0.3rc1-1 unzip-5.52-3
vorbis-tools-1.1.1-7 which-2.19-2 whois-4.7.24-1
wireless_tools-29-2 wireshark-0.99.7-1 wpa_supplicant-0.5.9-1
xaw3d-1.5-4 xchat-2.8.4-2 xf86-input-evdev-1.2.0-1
xf86-input-joystick-1.3.1-1 xf86-video-ati-6.7.197-2
xf86-video-mga-1.9.100-2 xf86-video-nv-2.1.7-1
xf86-video-s3virge-1.9.1-9 xf86-video-savage-2.1.3-2
xf86-video-sis-0.9.4-2 xfsprogs-2.9.4-2 xfsdump-2.2.46-3
wavpack-4.41.0-3 xine-lib-1.1.10-1 xinetd-2.3.14-3
xkeyboard-config-1.1-1 xmms-1.2.11-1 xorg-server-1.4.0.90-6
xorg-xinit-1.0.7-3 xscreensaver-5.04-2 yelp-2.20.0-3
zenity-2.20.1-1
Total Download Size: 743.90 MB
Total Installed Size: 748.87 MB
Proceed with installation? [Y/n]
Proceed with installation? [Y/n] y
:: Retrieving packages from core...
ncurses-5.6-6-i686 1738.2K 518.0K/s 00:00:03 [#####################] 100%
readline-5.2-7-i686 271.5K 228.3K/s 00:00:01 [#####################] 100%
bash-3.2.033-2-i686 407.1K 299.1K/s 00:00:01 [#####################] 100%
kernel-headers-2.6.2... 621.6K 376.8K/s 00:00:02 [#####################] 100%
tzdata-2007k-1-i686 610.7K 329.0K/s 00:00:02 [#####################] 100%
xorg-server-1.4.0.90... 7.4M 659.0K/s 00:00:11 [#####################] 100%
xorg-xinit-1.0.7-3-i686 14.4K 56.9K/s 00:00:00 [#####################] 100%
xscreensaver-5.04-2-... 8.0M 655.2K/s 00:00:13 [#####################] 100%
yelp-2.20.0-3-i686 603.4K 356.7K/s 00:00:02 [#####################] 100%
zenity-2.20.1-1-i686 1896.3K 546.6K/s 00:00:03 [#####################] 100%
:: Retrieving packages from community...
freetype1-1.3.1-4 119.9K 129.5K/s 00:00:01 [#####################] 100%
gkrellm-2.3.1-2 724.3K 411.1K/s 00:00:02 [#####################] 100%
xmms-1.2.11-1 1945.1K 557.0K/s 00:00:03 [#####################] 100%
checking package integrity...
(349/349) checking for file conflicts [#####################] 100%
( 1/349) upgrading ncurses [#####################] 100%
( 2/349) upgrading readline [#####################] 100%
( 3/349) upgrading bash [#####################] 100%
( 4/349) upgrading kernel-headers [#####################] 100%
( 5/349) upgrading tzdata [#####################] 100%
( 6/349) upgrading glibc [#####################] 100%
(340/349) installing wavpack [#####################] 100%
(341/349) upgrading xine-lib [#####################] 100%
(342/349) upgrading xinetd [#####################] 100%
(343/349) upgrading xkeyboard-config [#####################] 100%
(344/349) upgrading xmms [#####################] 100%
(345/349) upgrading xorg-server [#####################] 100%
:: Could not detect nvidia-utils on system
:: Will attempt to use built-in libwfb
(346/349) upgrading xorg-xinit [#####################] 100%
(347/349) upgrading xscreensaver [#####################] 100%
(348/349) upgrading yelp [#####################] 100%
(349/349) upgrading zenity [#####################] 100%
real 56m46.062s
user 4m25.013s
sys 1m46.520s
[root@arch-02 jada]#
And for your tread question.
How long does it take to do a dist-upgrade on your distro?
one hour
real 56m46.062s
user 4m25.013s
sys 1m46.520s
After reboot the system loads all new applications with out any problem. Later I replaced the intel-video driver "xf86-video-i810 1.7.4-6" with the driver xf86-video-intel 2.2.0-2. No problems at all.
Archlinux rocks

JaDa wrote:Archlinux rocks
definitely. By contrast, here's a regular upgrade on my debian box -- out of the blue it's having some problem with one of the packages, and it's turning into a regular recursive nightmare.
root@moe:~ # apt-get upgrade
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run 'apt-get -f install' to correct these.
The following packages have unmet dependencies.
E: Unmet dependencies. Try using -f.
root@moe:~ # apt-get -f install
Reading package lists... Done
Building dependency tree
Reading state information... Done
Correcting dependencies...Done
The following extra packages will be installed:
exim4-base exim4-daemon-light
Suggested packages:
exim4-doc-html exim4-doc-info eximon4 libmail-spf-query-perl
The following packages will be upgraded:
exim4-base exim4-daemon-light
2 upgraded, 0 newly installed, 0 to remove and 64 not upgraded.
1 not fully installed or removed.
Need to get 0B/1391kB of archives.
After unpacking 8192B of additional disk space will be used.
Do you want to continue [Y/n]?
Preconfiguring packages ...
dpkg: exim4-daemon-light: dependency problems, but removing anyway as you request:
exim4 depends on exim4-daemon-light | exim4-daemon-heavy | exim4-daemon-custom; however:
Package exim4-daemon-light is to be removed.
Package exim4-daemon-heavy is not installed.
Package exim4-daemon-custom is not installed.
dpkg: error processing exim4-daemon-light (--remove):
Package is in a very bad inconsistent state - you should
reinstall it before attempting a removal.
Errors were encountered while processing:
exim4-daemon-light
[ Rootkit Hunter version 1.3.0 ]
File updated: searched for 152 files, found 131
E: Sub-process /usr/bin/dpkg returned an error code (1)
root@moe:~ # apt-get install exim4-daemon-light
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run 'apt-get -f install' to correct these:
The following packages have unmet dependencies.
exim4-daemon-light: Depends: exim4-base (>= 4.69) but 4.68-2 is to be installed
E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution).
root@moe:~ #
It's so "delicate" and temperamental compared to the no-nonsense, straightforward approach of Arch. If one little thing is off, the entire system has a hissy-fit and won't do anything until you hunt the internet high and low searching for a solution, encountering all the debian hawks along the way who are ready to rip your head off at the first suggestion that debian isn't directly from god and could have a problem. Imo, Arch is the best linx distro hands down. Nothing else even comes close.

So how long does it take to load a 160GB iPod using the Convert Higher ...

I have a 160GB Gen 5 that I bought when first released back in the day when they were $400. Through a number of changes, the most recent being the advent of the Convert Higher Bitrate Songs to 128bit AAC feature, I decided to look at what more music I could store. After all was said and done, I ended up with a bit of a disaster with cover art not being properly applied to the music being played. I decided to *restore the ipod* based on suggestions in the discussion boards, and equally important was following the hints and tips here.
http://www.samsoft.org.uk/iTunes/grouping.asp
The advice is especially important in very large library situations to ensure you have uniqueness in the albums you want to display. Hadn't really given it much thought until I had the ability to see the individual albums for the 40K songs on the iPod via the cover art view.
Finally the point of the post...
*So how long does it take to load a 160GB iPod using the Convert Higher Bitrate option now available in iTunes 9.1?* The specs on my computer are not highend by any stretch, but it's no slouch, and neither of the CPUs are ever pegged. At this point I've lost count of how much time it's taken, but the load is going on 3-4 days. With some breaks in between because I need to check each incremental load to verify there is no cover art corruption, correct bad tags and such, but for the most part the loading is visibly slow, and I'm sure the conversion is the cause. I'm not really complaining at this point, but there is clearly room for improvement. And of course unless there is a redo involved in which case I will get quite cranky.
*I would like to hear the experiences of others.*
Finally to lend a bit more credence to the performance concern, my 32GB iPhone 3GS for only about say 28GB of music takes about 24 hrs to load from a 2.2GHz dual core intel laptop, again using the convert higher bitrate option.

With AC power adapter it takes 3-4 hours for a full charge. With the USB charger it takes 9-0 hours for a full charge. I am not happy with them removing the AC charger and other accessoreis at all. It's business but it still stinks.
I know I would rethink my purchase but would most likely end up buying the Micro anyway

HT5071 After submission, how long does it take for a new book to appear in the iBook store?

How long does it take for a new book to appear in the iBook store after you have submitted it successfully? I submitted a free book last night. No sign of it 6 hours later ... If the delay is because process are being followed, what ate they? Any ideas?

5-10 days in November.

How long does it take for Apple to send the content code for a free upgrade to Mountain Lion?

Has anyone managed to successfully receive the content code in their email for a free ugprade to Mountain Lion?
I bought my MBP on 14 July so I qualified for the free upgrade. Went to the website and filled in the form along with my serial number about 2 nights ago. Still haven't received my content code yet. How long does it take? Should I be speaking to someone already? Who?
Thanks.

We are being advised it can take up to 72 hours !

Time machine migration, how long does it take?

Im going to migrate to another mac using time machine, how long does it take (time machine/main hdd in the old mac was at about 700gb capacity)

There is no way of determining that. The time is dependent on a number of different factors.
Barry

No i'm using iPhone 4 16GB. i want to know how long does it take for "Erase All Content and Settings"?does it affects to iPhone's hardware? and if i want to restore my software in iPhone back, how i can do it?

no i'm using iPhone 4 16GB. i want to know how long does it take for "Erase All Content and Settings"?does it affects to iPhone's hardware? and if i want to restore my software in iPhone back, how i can do it?

it takes hours
it does not damage or wear out hardware
and you can restore any backup afterwards as yo see fit

How long does it take to get my X61 checked from water spill?

Hi,
I had spilled some water into my X61 yesterday.
Though I instantly shut it down and try to clean, I was too stupid to try to boot it in ten minutes.
Not sure if it is "OK" right now....
Does anyone have the same experience?
Could you share how long does it take you to have your laptop shipped and checked at lenovo repair center?
Thanks a lot!

do you have accidental damage warranty? if you don't then you will incur a hefty bill. The check up should not take more than 5 days including shipping, provided that no parts need to changed, if there is parts that are required, then depending on the parts availability, you could wait up to a month or two.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

HOW LONG DOES IT TAKE TO GET iPHOTO BOOK?

I would like to order my first HARD COVER book and since I am not living in USA, my friend would bring the book back to Europe.
But the only problem is that, she will be there only two days, so the book must be at the address, she will be living on 9th of February.
When do I need to place the order? How long does it take to get the album?
Thank you for your help.

Can't say - no idea where it is going to or what will be going on them
If it were me I'd say that the extra cost was a cheap insurance policy against external forces messing things up - but you make that decision
Waiting three days to order and shipping ground rather than express will increase the chances of it not making it - probably still 95% + (guessing of course) that it will but every day you wait makes the chances less and not using the fastest shipping also increases the chances of failure
If money is the issue then ordering today rather than Wed would be a good idea to me
Good Luck
LN

How long does it take to get my money back

Okay...I bought an app which I didn't liked...it cost 3.99 ... Then I reported the app and they send me an email saying ::::Recently you indicated a problem with Photo Director-HD Pro -make picture slide show music video .......by using the report a problem with iTunes. This email confirms that you have been awarded a refund of 4.32 on this purchase.i bought the app on December26,2013 ..
I have many questions
How I'm getting my money back?
How long does it take to get my money back?
Do I even getting my money back or not?
Please I need to know!!!! :'(

I had a similar experience yesterday. The Apple email that I got said:
"In five to seven business days, a credit of xx USD should be posted to the credit card that appears on the receipt for that purchase."
Your email should have said the same.
 Cheers, Tom

How long does it take to get approval from iTunes Connect and how do I find out if they are working on it?

How long does it take to get approval from iTunes Connect and how do I find out if they are even working on it? I'm not really sure if my application was even delivered - from the links in IBA. Any suggestions how one might push the right buttons at Apple?
Also went around in a big circle trying to get beyond the confusion of not having the right Apple ID when I've had it a long time. Confusion abounds and learning this forum also takes a new degree of patience. Humbling to say the least :-)
Anyone been there done that?

[email protected]
[email protected]
…support phone number call +1 (877) 206-2092.
Global Phone Support
We have expanded English-language publisher phone support. To make contacting the iBookstore support even easier, new local phone numbers are now available for Australia, France, Germany, Italy, Netherlands, Spain, and the U.K. Support is available Monday to Friday, from 7 a.m. to 5 p.m. (PT).
Country
Phone Number
Australia
1300 307 504
Note that this is a low tariff number.
France
0805 540 117
Germany
0800 664 5307
Italy
800 915 902
Netherlands
0800 0201 578
Spain
900 812 687
U.K.
0800 975 0615
U.S.
+1 (877) 206-2092
Toll-free from U.S. and Canada.

How long does firmware take to inst

Similar Messages

Maybe you are looking for