How many Airport Expresses possible?

Been looking far and wide for this answer.... how many Airport Expresses can iTunes stream to at once? I know with iTunes v6 and the firmware update it's possible to stream to more than one... but what's the maximum? Is there a max?
I know only one stream is possible I'd just like to figure out how many I could get. Thanks in advance.

Quoting from Apple's Airport Express FAQ:
Question: Can iTunes send a single AirTunes stream to multiple AirPort Express stations?
Answer: Yes. With iTunes 6.0.2 or later, you can send an AirTunes stream to multiple remote AirPort Express units, provided that each AirPort Express has the latest AirPort firmware (available here). The maximum number of remote AirPort Express units is three to six in typical conditions. The number that works for you will depend on your environmental conditions (such as building composition and local radio interference), distance to the remote AirPort Express units, and available network capacity relative to your other usage.
The practical limit on the number of Airport Express devices you can stream to at one time (as indicated in that paragraph) is determined by the available bandwidth of the wireless network.
The next question, of course, is how many could be supported if all Airport Expresses were cabled to an ethernet network.

Similar Messages

  • How many airport express can  i install in my home to stream music?

    I plan to buy many airport express in my new Home!
    how many airport express can  i install in my home to stream music?
    Jimmy

    jimmyflo wrote:
    I plan to buy many airport express in my new Home!
    how many airport express can  i install in my home to stream music?
    Theoretically as much as you want but there are technical limitations about the usable bandwidth in the wireless or by the used access point.
    All participants (stations) in a wireless network share the available bandwhith equally and therefore a point will get reached where the throughput in the network became insufficient to stream music.
    Also some routers limit the number of stations could get connected. For instance Apples Airport Extreme have a limit of 50 connected clients and the AP-Express (if used as access point) a limit of 10 simultaneous connections.
    Lupunus

  • HI, do you know how many airport express I can use per Mac????

    I need to know how many airport express can I use simultanously in my Mac ... any idea???

    Thanks for your question, I live in a 3 floor house, the cable router is in the 2nd floor, I already have one connected airport exrpess in the 1st one, but I need to increase the wifi signal in the 3rd one... so for that reason I would like to conecct one additoonal one to my wifi network...

  • How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.

    How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.
    What I'm looking to do is to have self powered in ceiling speakers in every room in my house with out having to run wires to every room to carry the audio signal. I would like to use the airport express to do the job of carting the audio signal.
    Here's my set up now I have an airport extreme and one airport express that I use to carry audio to one room.

    FWIW. I have used up to four AirPort Express Base Stations (AX) for streaming sucessfully in pretty much the way you have described. I didn't have a need to try more so I can't attest that more would or would not work.

  • How many airport express can be supported by software remote at one time.

    how many airport express can be supported by software remote at one time?
    I mean remote software can control at one time

    Well Apple makes an iOS application called 'Remote' it's used to control iTunes on a Mac, Or to control an Apple TV Multimedia features.
    Apple also makes "AirPort Utility" for iOS. Airport Utility can be used to configure Aiport Extrem, Airport Express And Time Capsul using an iPad, iPhone or iPod Touch. You can use it to connect to one device at a time. While connected to the device you can configure it to work as part of a larger Airport network. If you want to configure muliple device, you would connect to one device,  configure it,  And then connect to the next device, and configure it, and so on and so fourth.
    I haven't found a limit.
    How big of a network are you trying to make?

  • How many Airport Express...

    How many Airport Express units can be used simultaneously?  I have an audio application that is wireless and could potentially have 12-20 separate areas. The most I have actually ever tried is 4 and it worked fine.  Any limitations that anyone has read about, or has anyone tried this?

    Well, a standard "main" router that will supply DHCP and NAT services for the entire network will be able to allow up to a total of about 250 devices to connect. That would include the AirPorts, and any devices that are connected to the AirPorts and any other devices that you have on the network.
    Each AirPort Express (new version) will handle up to 50 wireless clients. It would be much better to limit that to 20-25 to keep the speed up.  So, you'll have to do some math to try to figure out how many total devices will connect to the network when everything is working.
    You could connect 20 AirPort Express devices to the main router....but you would only be able to connect about 10-15 devices to each Express.
    Or, connect 10 Express devices to the main router and you can connect about 20-25 devices to each Express.
    If you plan to connect to the Internet, keep in mind that all devices will share the bandwidth. If you have a 100 Mbps Internet connection, and 100 clients connected to the network, then each client will get about 1 Mbps. Pretty slow.
    I'm not sure what your audio application is here....the network examples I am providing assume that you will be connecting wireless and wired Ethernet clients to the network.
    If you could detail your proposed system, other users could offer their comments. We're still pretty much guessing at hypotheticals at this point.

  • How many AirPort Express stations can be supported by an AirPort Extreme wirelessly?

    I got one AirPort Extreme in my home and would like to extend the wireless network by purchasing additional AirPort Express.  Wanna know how many AirPort Express stations can be supported by an AirPort Extreme wirelessly?
    Thanks.
    Tony

    Bob -- question for you which I can't answer as I don't have an airport extreme. The newer Extremes can create both G and N networks and can create the N network in the 5 mhz band. Can you increase the number of Express units you can connect wirelessly if you split the load between the 2.4 mhz G and 5 mhz N networks created by the Extreme. (recognizing that the 5 mhz band has less range than the 2.4 mhz band)
    Not an issue for me as I only have three connected wirelessly, but I've always wondered about this. Of my three AX units one connects to a G network created by a Linksys WRT54GS and two connect to the N network created by the AX.
    So instead of 3-4 AX units could it become 6-8?
    Carlos

  • How many Airport Expresses can you link and still work properly

    How many Airiport Expresses can you link and still work properly.

    It would depend on whether all of these base stations will be interconnected by Ethernet or by wireless and what your goal is with them.
    In a roaming network, where all base stations would be connected by Ethernet, you could have 10+ base stations. Apple has never (at least to me) any limits on the number of base stations that can be used in this type of network.
    In an extended network, where all of the base stations use wireless connections, the practical limit would be 4 or 5 base stations.

  • How many Airport Express do I need?

    I have my network setup in the basement. I would like to use AirTunes to listen music upstairs in the 3 bedrooms. Do I need 3 Airport Express?
    Are there any Speakers that natively support AirTunes? Any other options?
    Thanks

    Welcome to the discussions!
    There will need to be an amplifier and speakers or powered speaker arrangement connected directly to each AirPort Express, so the number of Express devices will depend on how many separate amp/speaker configurations you want to set up.
    If you want speakers in each room, you will need 3 Expresses.
    I'm not aware of a speaker system that is designed specifically for AirTunes. Virtually all small powered speaker systems use the same type of audio plugs and connections, so compatibility should not be an issue.
    To insure that the Expresses will function well, I would also suggest that you take a laptop upstairs and try to connect to the internet to make sure that you have adequate signal strength in the areas where the Expresses will be located.
    If you have an Apple(n) base station in the basement, you will also be able to configure the Expresses to "extend" the wireless network, which will give you much better wireless signal strength upstairs.

  • How many airport expresses would I need for a 3000 square foot apartment with minimal walls?

    The apartment is open-air style with minimal walls. I have two airport expresses currently and am wondering if this will be enough to cover the entire apartment? Any help is much appreciated. Thanks!

    You'll get about 50ft @ (-6db), you'll get about 100ft @ (-12db), both of these are useable figures, beyond a 100ft it will be patchy
    This assumes your AE is in free space, which it won't be as you need to plug into something, the more intersections (wall/ceilng wall/floor) the greater the chance of multipath rejection.
    3000sq ft relatively empty of dividers is a good space, but I would use 2

  • How Many AirPort Expresses can you use with BaseStatio to Exended Coverage?

    I have the airport Extreme N Base station and have one airport N Express hooked up to get better coverage...
    can I hook up more than 1 express to make a bigger coverage area on my property?
    Thanks

    can I hook up more than 1 express to make a bigger coverage area on my property?
    Yes, but you cannot connect the additional 802.11n base stations in series to extend the range as the 802.11n "extend" feature does not support relays like in a 802.11g WDS.

  • How many items are possible in page APEX 3.2

    Hi All,
    I have created around 95 page items,8 different region , 10 buttons and i have used collections in page processing
    While processing the page by using Select with LOV getting error http://3264-ch-dbs:8080/apex/wwv_flow.accept
    I have created 15 extra page item due whih count increases from 80 to 95 .once I have created this I tried processing the page by select list with submit . I am getting above mentioned error
    how many items are possible in page APEX 3.2 , is there limitation ?
    Any sugeestion is welcomed
    Thanks and Regards
    Sachin

    Hello Sachin,
    >> how many items are possible in page APEX 3.2 , is there limitation ?
    You can render up to 100 APEX item on the page, and that includes hidden items. You can define more than 100 items and use conditions to determine which items will be rendered. (Buttons and other components you mentioned are not included in the 100 count).
    Regards,
    Arie.
    ♦ Please remember to mark appropriate posts as correct/helpful. For the long run, it will benefit us all.
    ♦ Forthcoming book about APEX: Oracle Application Express 3.2 – The Essentials and More

  • How many Airport Extreme's and Airport Express can extend line for distance

    I am trying to link multiple AEBS/AE's together to cover a fairly long distance between two houses....Is this possible? I already have the 2 AEBS's linked together between two houses going across a street. However, the link is not that strong and I am seeing packet loss. I am thinking to plug at least one AE in at the far end of the house closest to the window to possibly help get a stronger signal going across the street.
    Would this work? Will it just add too much latency?
    DSL Modem---AEBS-1>>><<<AE>>><<AE>><<<AEBS2---iMac on gigE

    Welcome to the discussion area, 0dB!
    +Would this work?+
    The short answer here would unfortunately be a "no". Read further for explanations.
    If this is a newer AirPort Extreme (AEBS) "n" device and you are using a newer AirPort Express (AX) "n" device, you will not be able to configure the network as you describe. The reason for this is that the AX communicates directly to the main AEBS in the "extend a wireless network configuration". So the setup would look like this:
    Main AEBS > Remote AX.
    That's the limit of this type of setup, although you could have multiple remote devices if you wish. It's like the hub and spoke of a wheel. The AEBS would be the hub and AX would be at the end of a spoke. No further extension is possible from the AX, although you could have several devices communicating to the AEBS if needed.
    Apple's older WDS configuration allows the following:
    Main AEBS > Relay AX > Remote AX.
    That is the limit of this type of setup. Keep in mind that there will be a tremendous loss of performance with this type of setup as follows:
    1) The entire network will operate at "g" level wireless
    2) The bandwidth of the network will drop to only 25% of the original bandwidth
    With WDS, in effect, you will have a "g" wireless network operating at 25% of its normal capability.

  • How setup Airport Express to secure/private network behind Netopia router?

    Hi!
    I just purchase a Macbook and Airport Express - here are my questions:
    1) how do I set up a network so I only recognize my airport (so many other airport/wireless networks are showing up - I do not know which is mine!)?
    2) how do i then secure this network (best possible built-in security)
    Other data: I connect to the Internet via a DSL cable modem which feeds a netopia router which then serves IP addresses and uses DHCP.
    Thank you!

    I figured it out - used the airport utility in "utilities" and was able to find my specific Airport Express base station and configure securely - yippeeee!

  • Allow wireless PC to access files on my Mac via airport express - possible?

    I currently access the internet wirelessly via an airport express plugged into a netgear router, everything works great.
    I also have a spare pc that i would like to be able to access the net wirelessly - it currently doesnt have a wireless card but i figure if i just get a usb unit it should be able to without too many problems as it should just detect my airport network (hopefully anyway).
    Befor i go get the card tho, i was wondering if there will be a way to allow me to transfer files between the Mac HD and the PC HD - it wouldnt have to be 2-way, just so i could sit at my mac and send files over to the Pc - is this possible, and if so, a little help in how exactly to set it up would be appreciated!
    cheers!!

    using the guide on that page i have managed to
    connect to the Mac from the PC, but i am unable to
    see the folders on my external hard-drive
    You will need to use Sharepoints in order to share the external hard drive.
    http://www.hornware.com/sharepoints/
    iFelix

Maybe you are looking for

  • How do I turn off the add-on bar so it doesn't turn itself back on?

    By right clicking on the menu I can turn on or off the various toolbars including the Add-on bar. But if I create a new tab or new window it turns on the add-on bar again. How can I turn it off so it does not reappear?

  • HT202157 Why does Apple TV say Netflix is not available when I can watch it on my computer?

    I have reset my Apple tv to factory defaults, but it did not ask me to activate it again. For the last two days everytime i try watch a Netflix movie is says Netflix is not availble please try again latter. I have also power cycled my apple tiv by le

  • SES - Change network disabled at plant level

    I am looking at the config in ML81N  - Create Service Entry Sheet. We have locked out the ability to change the network number at the SES , based on plant. We have allowed the change of Cost Center at all plants. My issue is I am trying to find where

  • Building GNOME with jhbuild

    I am trying to build all of the GNOME modules with jhbuild, just everything standard, nothing special. I ran jhbuild build and got jhVariable 'exec_prefix' not defined in '/usr/lib/pkgconfig/geoip.pc' buiVariable 'exec_prefix' not defined in '/usr/li

  • Navigating between scenes using buttons

    Hi, I have created several scenes that all have the same navigation bar consisting of l buttons which take the user to the various scenes. The code for the buttons (listeners and handlers)is on frame one in the first scene. It works fine as long I am