How many command line can 7507 support

hi
i have a problem
if i wnat to setup static lu point to ip address
i will need two line to define
but in my cx site have more than one thousand pc
so i need to define
client ip x.x.x.x lu 2
client printer ip x.x.x.x 3
plus 1000 pc
it will exceed two thousand command line
how many capacity does 7507 have
tks

Hi,
i found this in the CCO:
Handling Large Configurations
The largest size nonvolatile random-access memory (NVRAM) planned for the Cisco 7500 series routers is 128 KB. The maximum number of nailing commands that can be stored in a 128 KB NVRAM is approximately 4000. However, large configurations may map as many as 10,000 IP addresses to LUs.
To maintain a configuration file that exceeds 128 KB there are two alternatives. The configuration file can be stored compressed in NVRAM. Or, the configuration file can be stored in Flash memory that is either internal Flash or on a PCMCIA card.
look at this Link:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios112/bclunail.htm
cu thomas

Similar Messages

How many airport express can be supported by software remote at one time.

how many airport express can be supported by software remote at one time?
I mean remote software can control at one time

Well Apple makes an iOS application called 'Remote' it's used to control iTunes on a Mac, Or to control an Apple TV Multimedia features.
Apple also makes "AirPort Utility" for iOS. Airport Utility can be used to configure Aiport Extrem, Airport Express And Time Capsul using an iPad, iPhone or iPod Touch. You can use it to connect to one device at a time. While connected to the device you can configure it to work as part of a larger Airport network. If you want to configure muliple device, you would connect to one device, configure it, And then connect to the next device, and configure it, and so on and so fourth.
I haven't found a limit.
How big of a network are you trying to make?

How many 7920 phones can be supported on one Cisco 1131AG access point?

hi all,
who knows that how many 7920 phones can be supported on one 1131ag AP? Thanks a lot...

Hi Alomar,
Hopefully this info will help;
Number of 802.11b Phones per AP
Before any discussion about network planning can take place, it helps to understand the basics of the overall network capacity.
The following network capacity guidelines apply to sizing the Wireless IP Telephony network:
No more than 7 concurrent G.711 calls per AP.
No more than 8 concurrent G.729 calls per AP.
Note These design recommendations assume that Voice Activity Detection (VAD) has been disabled on the Cisco 7920 Wireless IP Phones. Use of VAD on the Cisco 7920 phones can conserve bandwidth, but Cisco recommends that you disable VAD on all Cisco CallManager servers to provide better overall voice quality.
In addition to determining how much bandwidth is needed for an 802.11b VoIP call, you must also consider overall radio contention for a particular RF channel. The general rule is that you should not deploy any more than 20 to 25 802.11b endpoints per AP. The more endpoints you add to an AP, the more you reduce the amount of overall bandwidth and potentially increase transmission delays.
The maximum number of phones per AP depends on the calling patterns of individual users (based on Erlang ratios). Cisco recommends no more than 7 concurrent calls using G.711 or 8 concurrent calls using G.729. Beyond that number of calls, when excessive background data is present, the voice quality of all calls becomes unacceptable.
From this doc;
http://www.cisco.com/en/US/products/hw/phones/ps379/products_implementation_design_guide_chapter09186a00802a0a05.html
Hope this helps!
Rob
Please remember to rate helpful posts.....

How many phone lines can i add to my conference calling feature.

How many phone lines can I add to conference calling on my iPhone?

That depends on your cellular carrier. Ask them.

How many external monitors can I support with 13" rMBP (late 2012)?

Device has two DisplayPorts and each is powering an external display properly. It also has an HDMI port. Can I connect a third monitor here?

I got my new 13" Retina in the other day (late 2013 model ME865LL/A)
I was all excited to see if the two Thunderbolt 2 outputs and the HDMI output would work together, but plugging in the HDMI output knocked out one of the Thunderbolt outputs, so what I read was right, the 13" model will only power two external monitors. Before I got this I kept reading over and over how it wasn't possible, but that was dealing with the Late '12 or the Early '13 models, I was hoping that the upgraded video card on the newest Haswell versions may be different, but alas, not to be....
But I did implement a work around as I have a Matrox Triple Head 2 Go DP Edition for my old Macbook and what that does is make my two Lenovo 22" widescreens look like one big 3840x1200 monitor to it's host (tricking the MB to thinking "hey, this is one monitor"), so this allows me to use one Thunderbolt output to power these two monitors and then I am using an HDMI --> DVI cable to power an HP 23" widescreen monitor I also have running at full resolution, all this in addition to the Laptop display as well:
Here is a quick 20 second video of all monitors playing video.... the one on the left in the middle row was staggering but that is more a problem with AMC's website more than anything, I never get good stream speeds from their site
https://www.youtube.com/watch?v=OfIsupl3psc
I just installed iStat 4 an hour ago and am showing CPU temps around 150 degrees, not really sure what "normal" is or what is acceptable...... I'm going to keep tabs on what the temps are as I finish up my workday here (another 6 hours to go)
I still want to re-arrangle things so i only have two levels of screens to deal with, but still formulating that setup with my desk

How many concurrent requests can WAS support?

Hi all,
I want to know what is the maximum number of concurrent users/requests that can WAS6.4(latest pack) support? We are looking at around 40,000 concurrent users.. Is this feasible? If yes what is the max possible?
Regards,
Harsh
PS: Would appreciate a prompt response:)

Hi Harsh,
I was just reading those notes that Alexander found as well and I would have to agree with him the that webdispatcher could handle the 10,000. However you have to remember that if you are running a BSP or other application located on a WAS server you have the constraints there as well.
Now I've just done some load testing with some stress tools.
500 concurrent connections on a Linux server dual processor 4 GB RAM and I started to see some major performance problems. Any higher and the system or at least the apps would have started to hang I think.
So with 40,000 connections even with loadbalancing and application instances you are going to need some major hadware to handle the connections.
Now back to your other questions.
The WAS and the R/3 are built on the BC level, which means the basic connections are made at that level and effected by these parameters. With a 640 Java Stack only then you have the J2EE engine only in which case the BC level is basically not there at least not like the ABAP level.
Now if you have a single JSP page deployed on your J2EE and not making any RFC calls to your backend then you only have to worry about the dispatcher connections. However, from my understanding if you make those RFC calls then you have the connections of the backend to worry about as well.
Now if you can gives a bit more detail of what the connections (all these 40,000 are doing) then perhaps we can come up with some alternatives that will help out.
As for being intimidated, don't be, I'm learning this from searching as we go along as well

How many Story Lines may I have ?

Hello everyone!!!
So, I'm a musician and I wanna make music videos to youtube (just like thousands of other people do)...
Wanna make my videos with FCP X...
I saw some videos (tutorials) on youtube about tips and tricks on FCPX... Problem is that at any video (tutorial) I watch there's only a main story line...
On some videos I may see the main story line and a secondary track above...
Once I saw a tutorial that I can transform the secondary line into a story line - and then it will act just like my main story line.
What I want to point out is that as a musician and making a music video, I would need maybe 6~9 story lines (for all instruments and stuff)... Because spliting the videos and sycing them over and over again would be annoying... It would be a lot easier if I could just have how many story lines I want, have them all sync and then just split the videos...
(Hope I was clear enough, english is not my main language, sorry for that)
So, to simplify, my question is: How many story lines can I have in FCPX ? (at least 2 I know I can have 'cuz I've already seen this on tutorials, wanna know if it is possible to have more than 2 or if 2 is the limit)
Thanks already everbody!!

Salivan, you can have as many storylines as you like.
What you need to do is place your first or main instrument I the primary storyline. Add your second instrument as a connected clip, and turn that into a storyline by selecting it, right click & select create storyline.
Now there is no reason why you can't add another connected clip above the secondary storyline, and place that clip or clips into another storyline.... and so on

How many Voice connections can cisco 2821 support?

Good day.
I have a cisco 2821 with EVM slot, NME-X slot and two HWIC slots. I have 4 port FXOs on the two HWIC slots. The EM-HDA-8FXS module on the EVM slot can handle 8 FXS connections. Please i would like to know if there is an EVM module that can do FXO connections and also how many voice connections can this router handle in total. Can the EM-HDA-8FXS module handle both FXS and FXO connections?
Hope someone can help me out. My deadline has already passed.
Regards,
Obinna.

Hi, already replied to this in the appropriate forum.
Please do not open duplicate threads.

How many Iphone 5 can you open under one account ??

Just a simple question , how many iphone 5 can you open under one account ? is it 5 or more ??? anyone know . I've been a verizon customer for a little bit over 5 months ..... any input ??? thank you

I'd call Customer Service and ask, because the Share Everything plan is supposed to allow 10 lines:
http://support.verizonwireless.com/clc/faqs/Calling%20Plans/share_everything.html

I'm a school tech coordinator. Many computers and many iPads. How many Apple IDs can I have per device, and how many devices can have the same Apple ID? To make my life easier, I'd like 200 devices to all use the same Apple ID.

I'm a school tech coordinator. I have many computers and many iPads. I apologize if there is a some place that has all the rules governing the use of Apple IDs. I looked, and I even tried to get the answers from multiple Apple rep's. I couldn't find the answers.
How many Apple IDs can I have per device?
I want to use the same computer to sync and backup many iOS devices. The iOS devices would be associated with different Apple IDs.
I may load apps under a school Apple ID and have users load their own apps under thier own ID.
How many devices can have the same Apple ID?
Can I use the same Apple ID on all the computers in a lab?
Can I use the same Apple ID on all iPads for a particular grade level?
Are the rules different for iOS devices and computers?
I know that there are limits on "authorize" and "de-authorize" and how frequently those things can be done.
Recently I heard that for the life of an iOS device, it can only be associated with five Apple IDs. That is not good for a school giving iPads to students in a 1:1
To make my life easier, I'd like 200 devices to all use the same Apple ID.

iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html
It would be best to address your questions there, especially since this is a public forum, and over there you could post more private issues with this set-up. Not to mention, getting more official answers.

How many apple tvs can i use on one network from one apple account ?

how many apple tvs can i use on one network from one apple account ?
if i have 16 in each of my rooms connected to a network switch and a good fiber internet line
will this work ok from my one account ? or would i neeed a mac book mini with raid storage set up ?
any help would be very gratfully recived !
james

Welcome to the Apple Community.
Homesharing allows up to 5 computers to be authorised and a total of 10 computers and devices to be associated with a single Apple ID.

At max how many logical columns can be created in RPD

Hi All,
At max how many logical columns can be created in RPD. I have a requirement of creating 200 columns. Will there be any problem .
Is there any predefind number of columns for RPD creation??
Please help ..

Hi Annapurna,
There's no limit that I'm aware of or which is mentioned anywhere. Just as an example: I have a logical fact table with around 750 logical columns (>500 original measures & 250 derived measures). No issue whatsoever. Opening the presentation table through answers takes about 2-3 seconds (the NQSQL command has a lot to retrieve), but that's about it.
Cheers,
C.

HT1277 How many mail accounts can I configure in "Mail" on my mac book pro ?

Im trying to open multiple mail accounts in "Mail" but am unable to. How many mail accounts can I configure ?

http://support.apple.com/kb/TS3276
http://support.apple.com/kb/HT1277
http://www.apple.com/support/macosx/mailassistant/
should be as many as you want
http://www.dummies.com/how-to/content/adding-a-new-mail-account-in-mac-os-x.html

How many internal HDs can I add to my G4 AGP tower?

Hi all,
How many internal HDs can I add into my G4 tower? I want to buy and use a SATA controller PCI card to break the 137 mb barrier and add 3 or more hds for my graphics art files, video and music files. Sort like a server right?
Thanks
web dude

Hi, Web dude -
What do you mean by this? They have power packs plugged to them and they're plugged in a strip?
Yes.
The firewire bus is designed to be able to provide power for use by an attached device, in addition to providing a data pathway. There is a limit as to how much power can be provided by that bus. Such power is used by the device to operate its mechanics - in the case of a firewire hard drive, to run the motor that spins the platter(s) in the drive.
Many, if not most, firewire devices can also be powered by using a separate power supply, often an external transformer although some may have that transformer built in. This necessitates a separate connection to line power, typically to an outlet on a power strip or surge suppressor strip.
When I ordered each of my firewire drives, I also ordered the optional power supply for it. This makes each drive non-dependent on the Mac for operating power.
How should I prevent over heating my G4?
As far as keeping a Mac from overheating, the primary defense is to keep it clean inside. Dust is both an insulator and a restrictor of airflow. Using canned air regularly to blow dust out of the inside of the Mac, and to clean its fans, goes a long way to keeping it from overheating. Using a vacuum cleaner is not recommended - it's too easy for the nozzle to bang into something, and the airflow going into a plastic nozzle can create static electricity, which you do not want around any printed circuit board.
Keep the machine itself adequately ventilated - it needs a reasonably unrestricted supply of fresh air. If you place the tower on the floor or under a desk, make sure there are several inches of free space between the case and any obstructions. Usually, keeping it on a desktop reduces the amout of dust it will ingest.
In addition, whenever possible use external power for a device - this applies to firewire and USB devices.
Hard drives generate a fair amount of heat. G4 desktop models are designed to accommodate up to four internal hard drives, though it is possible to install more than that. If you go beyond four internal drives in a G4, consider replacing the fans with ones with a larger capacity to handle the increased heat load.
If you replace the CPU, be sure you follow the instructions with the new one re making sure the heat sink on the new processor is installed correctly.

Clearmake: Warning: Too many command lines for "pcscfg.cfg"

Hi,
We are in the process of migrating an application(contains pro*C code) from oracle 9i to 10g.
When the application is compiled on oracle 9i the compilation used complete with out any problems.
After we changed the ORACLE_HOME parameter in our makefile to point to 10g home. clearmake
gives the following Warning. though the build is successful
clearmake: Warning: Too many command lines for "pcscfg.cfg"
Could anybody please help me in getting rid of this warning?
Regards
Srikrishan

Hi,
I have removed all unwanted things from the makefile, but the problem is still there.
I have included a sample program and the makefile which reproduces the problem.
The problem goes away if I comment out 4th line from the makefile and use 5th line instead
Could anybody please help?
#################The contents of the make file are #####################
targets: proctest
#ORACLE_HOME= /data/oracle/product/9.2.0
ORACLE_HOME= /data/tsd_oracle/hpux/10.2.0.2
include $(ORACLE_HOME)/precomp/lib/env_precomp.mk
#include /data/oracle/product/9.2.0/precomp/lib/env_precomp.mk
ORACLEINCLUDES= -I$(ORACLE_HOME)/precomp/public
PROCSYSINCLUDEOPT=sys_include='(/usr/include,/opt/aCC/include,/opt/aCC/include/iostream)'
ALLPROCINCLUDEOPTS= $(PROCSYSINCLUDEOPT)
PROCPPFLAGS= sqlcheck=full lines=yes code=cpp def_sqlcode=yes $(ALLPROCINCLUDEOPTS)
ACC=/opt/aCC/bin/aCC
ORACLELIBS= -L $(ORACLE_HOME)/lib32 -l:libclntsh.sl
#===========================proc test==================================
proctest:proctest.o
$(ACC) -o proctest $(ORACLELIBS) proctest.o
#========================= General target rules ============================
proctest.o:
$(ORACLE_HOME)/bin/$(PROC) $(PROCPPFLAGS) CPP_SUFFIX=cc iname=proctest.pc
$(ACC) $(ORACLEINCLUDES) -c proctest.cc -o proctest.o
#####################program (proc test.pc)#########################
#include<stdlib.h>
#include<iostream.h>
#include<sqlca.h>
#define UNAME_LEN 20
#define PWD_LEN 20
EXEC SQL BEGIN DECLARE SECTION;
VARCHAR username[UNAME_LEN]; // VARCHAR is an ORACLE supplied struct
varchar password[PWD_LEN]; // varchar can be in lower case also
EXEC SQL END DECLARE SECTION;
void sql_error(char *msg);
int main()
EXEC SQL WHENEVER SQLERROR DO sql_error("ORACLE error:");
username.len = (unsigned short)strlen(strcpy((char *)username.arr, "scott"));
password.len = (unsigned short)strlen(strcpy((char *)password.arr, "tiger"));
EXEC SQL CONNECT :username IDENTIFIED BY :password;
cout<<"Connected to oracle \n";
return(0);
void sql_error(char *msg)
EXEC SQL WHENEVER SQLERROR CONTINUE;
cout << endl << msg << endl;
cout << sqlca.sqlerrm.sqlerrmc << endl;
EXEC SQL ROLLBACK RELEASE;
exit(1);
####################################################################

How many command line can 7507 support

Similar Messages

Maybe you are looking for