How many RAID 0's can I support?

Hi All,
I've got an ASUS Sabertooth MB, Core i7 950, 12gb Tri Channel 1600 mhz ram, 850 watt corsair power supply,a nd GTX 470.
My boot drive is a 300gb Velociraptor, and I have 2 Samsung 1 TB in a RAID 0.
Question:  Can my setup support another RAID 0?  I only ask cause I can get 2 Western Digital 500 gb drives for $50 each and I think it would compliment my system nicely.
Any feedback would be greatly appreciated.

Adamousman,
Your system sounds solid and also pretty balanced to me as described already. Before I would comment where to add a small investment to improve on what you have already, I would like to see your PPBM5 score broken down by category. Have you run PPBM5 yet?
Also, in another one of your threads, Cristobal suggested you overclock your 950 to 4 GHz. If you still have your stock cooler, ditch it for something better and overclock you CPU at least some, even if not up to 4.0.
If you have not seen my thread on how changes to various PC components impacted my PPBM5 score, check it out to get a feel for how CPU speed, RAM size, and drive setup changed how fast Premiere Pro performed on a single system:
http://forums.adobe.com/message/3465135#3465135
You will see that drive improvements past a 2xRAID 0 like you already have were pretty subtle.
Harm and Bill preach the importance of a good Premiere Pro system being a sum of all of the parts and that is so true!
Regards,
Jim

Similar Messages

  • How many AirPort Express stations can be supported by an AirPort Extreme wirelessly?

    I got one AirPort Extreme in my home and would like to extend the wireless network by purchasing additional AirPort Express.  Wanna know how many AirPort Express stations can be supported by an AirPort Extreme wirelessly?
    Thanks.
    Tony

    Bob -- question for you which I can't answer as I don't have an airport extreme. The newer Extremes can create both G and N networks and can create the N network in the 5 mhz band. Can you increase the number of Express units you can connect wirelessly if you split the load between the 2.4 mhz G and 5 mhz N networks created by the Extreme. (recognizing that the 5 mhz band has less range than the 2.4 mhz band)
    Not an issue for me as I only have three connected wirelessly, but I've always wondered about this. Of my three AX units one connects to a G network created by a Linksys WRT54GS and two connect to the N network created by the AX.
    So instead of 3-4 AX units could it become 6-8?
    Carlos

  • How many GB of Ram can G500 support?

    Hi.
    I have a G500 with a 4gb of ram and I want to install the maximum that this laptop can support.
    After searching on the Net I saw here: 
    http://shop.lenovo.com/us/en/laptops/lenovo/g-series/g500/#techspecs
    saying:   Up to 8GB PC3-12800 DDR3 SDRAM 1600 MHz
    On  the other hand here: 
    http://shop.lenovo.com/gr/el/laptops/lenovo/g-series/g500/#tab-Τεχνικές_Προδιαγραφές
    says: 
    DDR3 έως 16 GB 1.600 Mhz (υποστήριξη δύο καναλιών) [2 υποδοχές SODIMM (1x 2 GB / 2x 2 GB / 1x 4 GB / 1x 2 GB + 1x 4 GB / 2x 4 GB / 1x 8 GB / 2x 8 GB)
    meaning that you can put 2 * 8 GB = 16GB maximum.
    Can anybody please inform me (with a site please) what is the right one? 8GB (2*4GB) or 16GB (2*8GB)?
    Thank you.
    Solved!
    Go to Solution.

    My 4Gb memory (one module) is 11 11 11 28.
    Can I put a two modules 8+8=16GB of 9 9 9 24?
    I have read  """"""The lower this is (tRas), the faster the performance, but if it is set too low, it can cause data corruption by deactivating the row too soon.""""""῾.
    Is there a possibility that the new memory modules are not good for the g500 I have?
    If anybody can help i would appreciate it.
    I dont want to spent 150Euros and then discover that the memory modules are not good
    I had put in a previous message a module I was thinking to buy but they cancelled my message. 

  • How many digital voice ports can Cisco 3663 support ?

    How many digital voice ports can Cisco 3662 support ?
    They said "Medium complexity Codecs: 360 (E1)/288 (T1) and High-complexity Codecs: 180 (E1)/144 (T1) "in Cisco 3660 voice gateway data sheet .
    But another document said you just configured 4E1 on a Cisco 3660 router .
    Which one is true ?

    Hi,
    There are some other issue except physically accepted number of voice port.
    http://www.cisco.com/en/US/products/hw/routers/ps259/products_data_sheet09186a00800921ed.html
    page will give you better idea. Even though you can install many voice ports into a router , there is other limits you encounter.
    Bets Regards

  • How many IDE drives & CDrom can be installed with SATA drives??

    How many IDE drives & CDrom can be installed with SATA drives??
    i have 2 IDE hard disks & 2 CDROM drives: can install SATA hard disk added to these drives or do i have to remove some???
    & if it can be added, can i install 2 SATA drives???
    THX in advance

    The 3 versions of this board that are available are:
    875P Neo-FISR (PCB 2.0)
    875P Neo-LSR (PCB 1.0)
    875P Neo-FIS2R (PCB 1.0)
    All of these boards will have the following ports provider by the chipsets ICH5R south bridge.
    2 x SATA (Supporting 2 SATA HDD drives)
    2 x PATA (Supporting 4 IDE devices)
    All 6 of these can be used at the same time (provided you are using win XP or 2K) you just need to make sure yor BIOS is set right.
    ->INTEGRATED PERIPHERALS
    ->ON-CHIP IDE CONFIG
    ATA CONFIG: S-ATA ONLY or P-ATA ONLY
    S-ATA/P-ATA KEEP ENABLED: YES
    OPERATE MODE:
    If you set to "legacy mode" S-ATA are set to channel 1 and 2 and P-ATA to channel 3 and 4. If you set to "native mode" P-ATA are channel 1 and 2 and S-ATA 3 and 4. You can only use the raid functionfon SATA in native mode.
    If you have the 875P Neo-FIS2R (PCB 1.0) you will also have the following ports provided by the Promise PDC20378 PCI controller:
    2 x SATA (Supporting 2 SATA HDD drives)
    1 x PATA (Supporting 1 Master IDE HDD drive)
    The PATA port is limited to 1 Master HDD by the lite BIOS. This can in theory be upgraded to the full BIOS supporting a master and a slave, but this may obviously void your warranty.
    So the answer to your origional question is:
    2 x SATA HDDs and 4 x IDE HDD/CDROM if you have 875P Neo-FISR (PCB 2.0) or 875P Neo-LSR (PCB 1.0)
    or
    4 x SATA HDDs, 1 x IDE HDD (2 if you modify the BIOS) and 4 x IDE HDD/CDROM if you have 875P Neo-FIS2R (PCB 1.0)

  • How many Multi-Touch points can an iPhone/iPod touch have at the same time?

    How many Multi-Touch points can an iPhone/iPod touch/iPad have at the same time?
    I am curious as IIRC (but forgot where the article is on the Internet),
    if a touch surface is wanted to be able to detect more than 1 touch point at the same time,
    then that touch surface needs adding 1 more conductive(?) layer.
    (e.g. 2 points -> 2 layers, and so on)
    So I wonder how many these layers are on the iPhone / iPod touch / iPad or even the trackpad on every MacBook (Pro).
    (correct me if I'm wrong)
    Just curious, thanks in advance!

    I believe it can only support 2. This article explains how the touch screen works but doesn't explicitly say how many points is supports.
    http://electronics.howstuffworks.com/iphone1.htm

  • How many numbers of GRE Tunnels are supported on Cisco 3925 router?

    Hi...
    I would like to know that.......
    How many numbers of GRE Tunnels are supported on Cisco 3925 router?
    Thanks....

    This is what I found in my search:
    There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
    https://supportforums.cisco.com/thread/2007932
    Hope it helps.
    Jatin Katyal
    - Do rate helpful posts -

  • How many licences does Final Cut Studio Support?

    How many licences does Final Cut Studio Support? Its the latest one (3) btw. The one that has FCP 7
    Any input is highly appreciated

    It can be installed on (1) desktop and (1) laptop, and you cannot use them at the same time. The idea is that you use the application when you are in your office, and if you need to go on the road, you can use it there, while the one in the office is not in use. 

  • HT5622 how many mobile (phone /ipad )can i connect to same  apple account?

    how many mobile (phone /ipad )can i connect to same  apple account?

    According to this Support Article  >  http://support.apple.com/kb/HT4627
    Your Apple ID can have up to 10 devices and computers (combined) associated with it.

  • How many web authentication users do 2125 support?

    when 2125 use local database for web authentication. how many web authentication users do 2125 support?

    thank you very much!!
    醉生梦死谁成气,拓马长枪定乾坤
    Date: Fri, 19 Aug 2011 01:10:43 -0600
    From: [email protected]
    To: [email protected]
    Subject: - Re: how many web authentication users do 2125 support?
    Cisco Support Community
    Re: how many web authentication users do 2125 support? created by pcroak in Getting Started with Wireless - View the full discussion
    Hello Yuliang,
    The maximum number of local database accounts that could be created is 2048. You can configure the size of the local database with the command:
    config database size <512-2048>
    NOTE: This local database count is shared between the following entries:
    MAC filters (clients)
    AP MIC/SSC (AP authorization list)
    Dynamic Interfaces
    Management users
    Local net users
    Excluded Clients
    If you are asking about the number of simultaneous wireless clients, I believe the 2125 supports 350 active wireless clients.
    -Patrick Croak
    Wireless TAC
    Reply to this message by going to Cisco Support Community
    Start a new discussion in Getting Started with Wireless at Cisco Support Community

  • How many Site Collections we can have in each farm in SharePoint?

    Hi,
    Can anyone please help me out with this that how many Site Collections we can have in each farm in SharePoint?
    I cannot able to find the related answers as of now.

    Hi,
    Go through the links below
    Software boundaries and limits for SharePoint 2013
    SharePoint Terminology – Farms, Web Front Ends, Web Application and Sites
    Permissions for site collection administrators
    Plan sites and site collections in SharePoint 2013
    Indul Hassan
    http://www.indulhassan.com
    You Snooze.. You Lose !!
    TechNet Community Support
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • Is there a restriction on how many simultaneous wireless iPads can watch movies from one iTunes account or AppleTV generation 2 or later?

    Is there a restriction on how many simultaneous wireless iPads can watch movies from one iTunes account or AppleTV generation 2 or later?

    Welcome to the Apple Community.
    I find it hard to believe that this information isn't clearly available somewhere, but it isn't and I don't think I've seen anyone here who is 100% sure. However, I believe you can have up to 10 associated devices, which include authorised computers (of which you can have up to 5), I suspect the Apple TV might become a temporary associated device while it's in use, but I'm not entirely sure myself.

  • How many numbers  of records can be uploaded  using BDC  at a time

    dear friends,
                      i want to know that how many numbers  of records can be uploaded using BDC  at a time from legacy system(database).

    no resticsation.
    large value of data  upload.

  • Is there any limit on how many records a cursor can hold?

    Hi Everyone,
    This is Amit here. I want to know whether there is any limit on how many records a cursor can hold.
    I have a program in which i am creating a cursor and passing it to another procedure as an input parameter. But the count of cursor query is more than 15 Lakhs. The program is running forever.
    Just wanted to know whether the huge data is the problem.
    Thanks ....
    Regards,
    Amit

    user13079404 wrote:
    Just wanted to know whether the huge data is the problem.What do you think? How long does your code typically need to wait for the data to leave the magnetic platter of the harddisk, travel across wires and into the memory buffer of your application - for a single row?
    Now multiply that waiting for I/O time with a million - for a million rows. Or by a billion, for a billion rows.
    Is "+huge data+" a problem? Not really - it simple needs more work to get that amount of data from disk. More work means slower performance. It is that simple.
    Which is why the row-by-row approach used by many developers is wrong. You do not pull a million rows from disk and process it in PL/SQL or Java or .Net. Heck, you do not even pull 10,000 rows like that.
    The correct approach is to think data sets and use SQL to process that for you - and only return the bare minimum of data to the application layer. Maximize SQL. Minimize PL/SQL and Java and .Net.

  • How many attribute views you can be used in analytical view

    how many attribute views you can be used in analytical view

    Any attribute declared at component level in "Attributes" tab can be used in any methods of the view
    WD_COMP_CONTROLLER->attribute
    Thanks
    Bhanu

Maybe you are looking for