How many web authentication users do 2125 support?

when 2125 use local database for web authentication. how many web authentication users do 2125 support?

thank you very much!!
醉生梦死谁成气,拓马长枪定乾坤
Date: Fri, 19 Aug 2011 01:10:43 -0600
From: [email protected]
To: [email protected]
Subject: - Re: how many web authentication users do 2125 support?
Cisco Support Community
Re: how many web authentication users do 2125 support? created by pcroak in Getting Started with Wireless - View the full discussion
Hello Yuliang,
The maximum number of local database accounts that could be created is 2048. You can configure the size of the local database with the command:
config database size <512-2048>
NOTE: This local database count is shared between the following entries:
MAC filters (clients)
AP MIC/SSC (AP authorization list)
Dynamic Interfaces
Management users
Local net users
Excluded Clients
If you are asking about the number of simultaneous wireless clients, I believe the 2125 supports 350 active wireless clients.
-Patrick Croak
Wireless TAC
Reply to this message by going to Cisco Support Community
Start a new discussion in Getting Started with Wireless at Cisco Support Community

Similar Messages

How many connections supports a web interface with each camera and how many Adobe Encoder clients does AMS support? AMS Standart

How many connections supports a web interface with each camera and how many Adobe Encoder clients does AMS support? AMS Standart. We need connect by Adobe Encoder many people. what is differences between Adobe Media Server 5 Professional, Adobe Media Server 5 Standard and Adobe Media Server 5 Extended?

For the detailed list of differences across editions refer this link
http://www.adobe.com/in/products/adobe-media-server-family/buying-guide-comparison.html

How many web.xml in a java application

Hi,
can anyone give tell the answer for this question "How many web.xml in a java application?"

1Why ?Because the Web container refers to only one web.xml for one web application.
I havent heard of an application having more than 1 web.xml
How?It reads all the definitions of servlet mappings, filters, welcome-file etc from this file itself.
Where?From the following folder ...
/WEB-INF
By the way ..... the way you questioned me was amuzing ... Why? How ?Where ? Its funny :D
I actually wanted to reply as below ..
Why ?Why not
How?
Wait lemme think ....ummm... What do you mean how??
Where ?
Inside the web ;-)
-Rohit

Typically, How many back and forths with Creative Support before they acknowledge your questi

Typically, how many times does one have to go back and forth with Creative Support before they acknowledge an issue or question?
This is ridiculous.
I'm on the forth reply now.
All I want to know is if there is a?64-bit ASIO driver for the X-Fi Titanium on 64-bit Vista?
They will not answer me.
All of my testing indicates that there is not a 64-bit ASIO driver for Vista, but they will not confirm or deny.
:angry:

dRe: Typically, How many back and forths with Creative Support before they acknowledge your question?U I don't know what Creative would have written if you asked SUpport these days?
I assume, they lied when they wrote this. There are several walkarounds for XFI cards
with beta drivers. In releas drivers they exclude the ASIOx64, but in beta it's included!
Creative has a very awkward marketing strategy. This was with Vista not having EAX on Audigy as
the said it is impossible. The newer X-FI was able to?do it and after a few weeks the Audigy also could-
after paying for it. The same with DolbyDigital Li've... and now with x64 ASIO. They reduce features
in cases the cheaper card had same possibilities as the more expensi've EMUs...
Shame on them. I?baught a creative Card for the 4th time (SB, SB AWE32,Audigy2, and now Titanium).
I'm going to thinking about selling it...

How many types of user defined functions are there?

how many types of user defined functions are there?

Hi Ramakrishna,
A user-defined function is only visible in the message mapping in which you created it. You can insert the function in the data-flow editor as a standard function by using the User-Defined function category.
You can use the following user-defined functions:
1.Simple functions, which can process individual field input values for each function call. Simple functions therefore expect strings as input values and return a string.
2.Advanced functions, which can process several field input values for each function call. You can import either all field values of a context or the whole queue for the field in an array before calling the function. For more information, see Advanced User-Defined Functions.
    go through :
http://help.sap.com/saphelp_erp2004/helpdata/en/22/e127f28b572243b4324879c6bf05a0/content.htm
     Advanced user-defined functions, which can process more than just individual field values.Instead, you can import a complete context or an entire queue for a field as an array before your function is called
    go through :
http://help.sap.com/saphelp_erp2004/helpdata/en/f8/2857cbc374da48993c8eb7d3c8c87a/content.htm
*Pls: Reward points if helpful*
Regards,
Jyoti

How to find a how many times a User logged in

Experts,
Is there a way where in I can find How many times a User Logged in to the system over a period of time.
FYI...,
I have a search over the forum but could not get the relevant solution for this. Had a trial search on TCodes SM04, SM20, STAD etc but could not find exact one for this.
Please let me know is there any way where I could get the details on the above query.
Thanks in adavnce.
Regards,
SRinivas

HI,
i found this fm RSAU_READ_FILE for sm20 , but i am not sure how to use it.
I just made a search for this function and i got thisa link
Check the reply by FabioBC in which he explains the mapping of fields to this function
link:[http://www.sapfans.com/forums/viewtopic.php?p=799746&highlight=&sid=e8dca9480a775847b26ab57493f27eb6]
Edited by: Keshav.T on Dec 3, 2010 8:16 PM

How many numbers of GRE Tunnels are supported on Cisco 3925 router?

Hi...
I would like to know that.......
How many numbers of GRE Tunnels are supported on Cisco 3925 router?
Thanks....

This is what I found in my search:
There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
https://supportforums.cisco.com/thread/2007932
Hope it helps.
Jatin Katyal
- Do rate helpful posts -

How many AirPort Express stations can be supported by an AirPort Extreme wirelessly?

I got one AirPort Extreme in my home and would like to extend the wireless network by purchasing additional AirPort Express. Wanna know how many AirPort Express stations can be supported by an AirPort Extreme wirelessly?
Thanks.
Tony

Bob -- question for you which I can't answer as I don't have an airport extreme. The newer Extremes can create both G and N networks and can create the N network in the 5 mhz band. Can you increase the number of Express units you can connect wirelessly if you split the load between the 2.4 mhz G and 5 mhz N networks created by the Extreme. (recognizing that the 5 mhz band has less range than the 2.4 mhz band)
Not an issue for me as I only have three connected wirelessly, but I've always wondered about this. Of my three AX units one connects to a G network created by a Linksys WRT54GS and two connect to the N network created by the AX.
So instead of 3-4 AX units could it become 6-8?
Carlos

How many licences does Final Cut Studio Support?

How many licences does Final Cut Studio Support? Its the latest one (3) btw. The one that has FCP 7
Any input is highly appreciated

It can be installed on (1) desktop and (1) laptop, and you cannot use them at the same time. The idea is that you use the application when you are in your office, and if you need to go on the road, you can use it there, while the one in the office is not in use.

How many licenses my comapny has and how many number of users logged in.

Hi All,
Can any one tell,
before login into the SAP B1,
I want to know
how many licenses my comapny has and how many number of users(Licenced) logged in using Query Analyzer or any other way.
Thanks
Chakrapani
Edited by: chakrapani bandaru on Feb 17, 2010 12:58 PM

Hi Sunderraj,
Can u eloberate the answer,
I want to take a report of that count.
Thanks
Edited by: chakrapani bandaru on Feb 17, 2010 2:14 PM

How to detect how many LOV values user selects on a WEBI Prompt

Hello Gurus,
Is there a way to identify how many LOV Values the user selects on a Webi prompt that allows multiple value selection?
For EG: If I have a webi and there's a prompt called State on the WEBI and the user selects "Utah", "Ohio" and "Texas" from the LOV and runs the query; is there a formula I can use to get the value as 3 (no.of selections)? If that's not possible, is there a way to find out if the user has selected more than 1 value?
Thanks,
RC

Hello,
From what I know there is no direct way of figuring it out. But here is a little trick.
Create a variable to capture the user response. Lets call it - State Prompt
It should display the values like this: Utah;Ohio;Texas
Next, get the length of the response string by using the length function.
=Length([State Prompt]). It should give you 15 in our above example.
Now, create another variable [let's call it - Replaced State Prompt] where you use Replace function, to replace/remove the ";" from the response string.
=Replace([State Prompt];";";"")
Next, get the new length of the new response string by using the length function.
=Length([Replaced State Prompt]). It should give you 13 as it removed two ";".
Now, do a subtraction and add 1 to get the count.
Overall it should be something like this-
=Length(UserResponse("Enter State")) - Length(Replace(UserResponse("Enter State");";";""))+1
Hope this helps.
Gaurav

How Many Foreign EoIP Tunnels Does 5508 Support?

Hi forum,
I'm speccing out a guest anchor design and can't find any explicit information for the 5508 regarding how many foreign WLC EoIP tunnels it can support.
This information for the 2504 is on the data sheet (15) but not on the 5508 data sheet!
Any help greatly appreciated, and given full stars

Osita is correct.
Just to add... Here is a link that explains it. Also if your going to reach that high of a number, you also have to understand the max client count on the 5508 (7,000) and the max database size for username/passwords if that guest WLC will handle guest accounts (2,048). This database limit includes local user and Mac filters also.
http://www.cisco.com/en/US/products/ps6366/products_qanda_item09186a00809ba482.shtml#qa2
Sent from Cisco Technical Support iPhone App

How many characters in users subscriptions of Interactive Report

Hi,
Can someone please help me in Apex 4.1. I would like to know how many characters can I enter in users subscriptions (email address) of Interactive Report and where data are stored.
Thanks,

Jessi wrote:
Can someone please help me in Apex 4.1. I would like to know how many characters can I enter in users subscriptions (email address) of Interactive Report and where data are stored.
Details of interactive report subscriptions are available in the APEX_APPLICATION_PAGE_IR_SUB APEX view. The maximum size of a subscription email address is 255 bytes.

How many Maximum number of work process supported by one application server

Friends,I have one confusion about the WP number:
how many maximum WP supported by one applicaiton server?
the appication server ENV is ECC6.0aix5.3oracle 10g on p595,if the supported maximum WP number is determined by number of CPU?if yes,what ratio between WPs and CPUs,thanks
Edited by: qz sun on Apr 8, 2008 10:47 AM

Hi Sun,
Please click on below link and you will get the solution.
http://help.sap.com/saphelp_erp2004/helpdata/en/19/da1c3d2b058c4ce10000000a114084/content.htm
Regards,
Anil

SNMP web authenticated users wlc 5508

Hello everyone,
I am using web authentication with my Wlc 5508 and I would like to check all users currently connected (ip, login used, MAC address, ...) with SNMP.
I am using an external web server and my client are authenticated with ldap.
I know I can receive these information with traps, but I would like to create a short program which will check all users when I click on a button.
Can anyone help me ?
Thanks a lot for your answers.

Hello Julien,
Thank you for the info. +5 for solving your own problem.
Regards,
Amjad
Rating useful replies is more useful than saying "Thank you"

How many web authentication users do 2125 support?

Similar Messages

Maybe you are looking for