How much RAM can be installed on a MacPro4.1?

How much RAM can be installed on a MacPro4.1?

physically 8 x 16GB, addressable in 10.8.3 is 96GB
you still on snow leopard? you can also use that.
6 x 8GB is probably more or as much as you need and try www.macsales.com/memory for kits

Similar Messages

  • How much ram can I install in macbook pro

    I have a 15" Macbook Pro with the 2.4GHZ processor.  Purchased in 2008.  How much RAM can I put in it?
    Thanks!  George

    Here is what I found.....
    Model Name: MacBook Pro
      Model Identifier: MacBookPro4,1
      Processor Name: Intel Core 2 Duo
      Processor Speed: 2.4 GHz
      Number Of Processors: 1
      Total Number Of Cores: 2
      L2 Cache: 3 MB
      Memory: 2 GB
      Bus Speed: 800 MHz
      Boot ROM Version: MBP41.00C1.B00
      SMC Version (system): 1.27f3
      Serial Number (system): W881****YJZ
      Hardware UUID: 25EAF703-47DE-5074-AACB-10371AD4B7EE
      Sudden Motion Sensor:
      State: Enabled
    System Version: Mac OS X 10.5.8 (9L31a)
    <Edited by Host>

  • How much Ram can I install in a mid 2011 mac mini, 2.3Ghz?

    I have a mid 2011 mac mini with a 2.3 Ghz processor and the factory installed 2GB of ram.  I would like to increase my ram but I am confused about the amount it can handle.  everywhere i look on the internet it says it can handle up to 8GB however i spoke with apple care on the phone and they said it can handle up to 16GB.  So which is it?
    thank you for your help.

    Click here.
    (115066)

  • How much RAM can I install in my Macbook Pro?

    I have a late 2011 model Macbook Pro. It is a 13 inch with 2.8 Ghz Intel i7 duo core processor and 4 GB (2 x 2) RAM. Can I upgrade to 16 GB (2 x 8) RAM?

    Installing RAM in a 2011-2012 MacBook Pro
    There is really only one way to install RAM into a 2011-2012 MacBook Pro and while there are hundreds of DIY videos online, I just like this one, found on YouTube, by “macmixing”.
    Note that there is a difference in the RAM that should be used in 2011 and 2012 models.
    2011 models must use:
    •204-pin PC-10600 (1333 MHz) DDR3 SO-DIMM
    And 2012 models must use:
    •204-pin PC3-12800 (1600 MHz) DDR3 SO-DIMM
    So here's the video:
    Remember that the 13", 15" and 17" 2011 models (early or late) and the 13" and 15" mid-2012 non-Retina models can handle 4GB, 8GB or (unofficially, but, believe me, it works) 16GB of RAM. There are, in my opinion, only three 100% Mac-compatible vendors out there: Corsair, Crucial and OWC. I really can't recommend any other brands, even though it may work, as these are the only brands that I've personally used in quite a while. Also remember to stay away from any RAM that is a “value” brand - Macs are picky about RAM and often these value RAM modules just don’t work very well.
    Good luck,
    Clinton

  • How much RAM can I install on my MacBook Pro?

    I'm thinking of upgrading the RAM on my MacBook Pro 13-inch Late 2012 Non-Retina with a 2.5 GHz Intel Core i5 chip in it. I currently have 4GB of RAM in it (2x4) and I want to upgrade to 16GB of RAM (2x8). Can I do this upgrade?

    Sure, you can remove the Ram that you have and replace it with 2 x 8GB chips. Macs are picky about Ram, buy it from OWC, or Crucial.

  • How much RAM can I install?

    Alright.  This seems simple but I don't want to have to go through the rigamarole of buying the wrong one and having to return it. 
    I have a Mid-2010 MacBook Pro running Lion 10.7.3, currently with the 4gb of RAM that it came with.  I want to upgrade this.
    I am aware that there are two slots that I can use to upgrade.  My question is this: the spec page for my model (http://support.apple.com/kb/SP582) states that it has "4GB (two 2GB SO-DIMMs) of 1066MHz DDR3 memory; two SO-DIMM slots support up to 8GB."  Does this mean that I can have 8 total (meaning I can only add 4), or that I can add 8 gigs, making a total of 12?  As far as I'm aware, the base 4 are located somewhere else inside the computer, leaving the two expansion slots empty. 
    Thanks in advance for any help. 

    Hi. You can upgrade to a maximum of 8gB, utilizing the 2 existing slots. You would need to replace both 2-2gB sticks with 2-4gB sticks.
    Stedman

  • How much ram can I install on iMac 2010, 21.5" i5 2.5ghz

    Hi
    I am considering to buy the cheapest iMac 21.5
    http://www.apple.com/imac/specs.html
    From the spec, it says it can only be upgrade to 8GB.
    But from the support center,
    http://support.apple.com/kb/SP623?viewlocale=en_US
    All models could upgrade to 16GB.
    Anyone knows why?

    The 8GB max might also refer to the "Late 2011 iMac Education Model" with an i3 processor with has a indeed a max. Ram of 8GB.
    Everywhere else the 21.5 iMac is said to support 16GB RAM (4 x 4GB).
    EveryMac and OWC/Macsales say it supports up to 32GB (4 x 8GB).
    Stefan

  • How much memory can I install in my mac book pro?

    Mac book pro 2.4 GHz late 2011 i7....How much memory can I install? Currently have 4Gb but want to run Win 7 on VMware and want to make sure my user has enough

    The position of Apple is that the Late 2011 can take 8 GB, however, OWC, http://www.macsales.com and Crucial, http://www.crucial.com both guarantee their 16 GB ram packages to work.  Both are sellers of high quality ram that is guaranteed to work in Macs.

  • How much ram can I put  In a 12" 867MHZ?

    Hi,
    I've just picked up a 12" 867mhz Powerbook for a very reasonable price! My question is how much ram can i put in it? It currently has 640mb. Also if i can put some more in it will it run Leopard?

    Bear in mind you can customise the install of Leopard to exclude some languages and particularly exclude printer drivers that aren't relevant to you, this will substantially lower the total required space. 12" Powerbooks are rather fiddly to work on - here's a really thorough guide on Hard drive replacement etc. for your Powerbook:
    http://www.ifixit.com/Guide/Mac/PowerBook-G4-Al-12-Inch/53

  • How much RAM should I install for new iMAC ?

    Hi,
    How much RAM should I install for new iMAC* running Logic Studio? It comes with 4 GB - is that enough? (can you run in 64 bit mode..)
    *(The 21.5" 3.06GHz Intel Core 2 Duo)
    Also, I was planning to get the stock 1 TB Hard Drive & save projects to an external drive.
    Does that sound reasonable?
    Any other recommendations?
    Thanks,
    Wm Heart

    Unless you plan on running huge projects with enormous sampled instruments, 4 GB will do (very) fine. And your disk plan is sound. Choose an external Firewire drive, rather than USB. FW is easier on the CPU and can handle more tracks than USB.
    What you should get, instead of more memory, is a (24 bit) external audio interface, if you want to do serious recording and playback.
    What type of audio interface you'ld need, depends on what you want to do with it and of course your budget. From decent to brilliant costs from roughly 100 to several 1,000's of europounddollars. Avoid the 16 bit ones, they're worse than the inbuilt audio chip of your iMac. You can recognize 16 bit Audio Interfaces (in webshops) by their prize (often under 100€£$) and the lack of mention of their bitrate.
    HTH
    Regards, Erik.

  • How much Ram can I add to my MacBook Pro?

    Another non-techie here with a memory question
    How much RAM can I add to my MacBook
    Model Identifier: MacBookPro2,1
    MacBook Pro (late 2006)
    Processor 2.33GHz Intel Core 2 Duo
    Current memory: 2GB (two SO-DIMMs) 667 MHz DDRs SDRAM (PC2-5300)
    The actual installation sounds quite simple.  I just want to be sure I get the right chips.  Any sources you can recommend?
    TIA
    Jim

    http://www.everymac.com/systems/apple/macbook_pro/specs/macbook-pro-core-2-duo-2 .33-17-specs.html
    3 gb of ram as two modules of 2 gb each.
    Try http://www.macsales.com/

  • How much RAM can go into my Macbook Pro

    Hey, I wanted to ask how much RAM can go into my Mid 2012 Macbook Pro I looked at this guide http://support.apple.com/kb/HT1270?viewlocale=en_US#link1 and it said I can only but In 8 GB I want to put 16 GB but was wondering if this would ruin my computer. I am asking because I have heard about 16 GB going into many Macbooks   Thank you!
    Here are my specs 
    13-inch, Mid 2012
    Memory  4 GB 1600 MHz DDR3
    Processor  2.5 GHz Intel Core i5
    Graphics  Intel HD Graphics 4000 1024 MB
    Serial Number  C1MKLGFEDTY3
    Software  OS X 10.9.1 (13B42)
    Your Mac contains 2 memory slots, each of which accepts
    a 1600 MHz DDR3 memory module.
    If any more info is needed than plz tell me and I will ad it

    The site below is highly recommended by folks on the forum.
    http://eshop.macsales.com/shop/memory/Apple_MacBook_MacBook_Pro/Upgrade

  • How much ram can my iMac take?

    Hi all, just bought a iMac a few days ago and I'm just wondering how much ram can it take as I want to upgrade it. It didnt come with a manual, so I don't know.
    Here's the spec so far
    Early 2008 20"
    Processor  2.4 GHz Intel Core 2 Duo
    Memory  2 GB 667 MHz DDR2 SDRAM
    Graphics  ATI Radeon HD 2400 XT 128 MB
    Software  OS X 10.8.2 (12C60)
    Thanks for any help in advance

    There are two answers: the official Apple answer and the "you're on your own" answer.
    1 - For the official iMac max RAM, see iMac Memory specifications and upgrades
    2 - For the "your're on your own" answer, everymac.com has a list of the Actual Maximum RAM you can put in every model Mac.  In many cases this is more than the official maximum RAM.
    After deciding how much RAM you want to put in your iMac, I suggest going to Crucial.com and use the memory advisor or system scanner to see what RAM modules are compatible with your iMac.

  • How much ram can I add to my late 2008 MacBook Pro? I run Mavericks and just got a new inexpensive hard drive. RAM is not very expensive so Thought I would bump it up from the current 2MB of 1067 Mhz DDr3

    How much ram can I add to my late 2008 MacBook Pro? I run Mavericks and just got a new inexpensive hard drive. RAM is not very expensive so Thought I would bump it up from the current 2MB of 1067 Mhz DDr3

    Maximum Memory
    8.0 GB (Actual) 4.0 GB (Apple)
    Memory Slots
    2 - 204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM

  • How much ram can i max out on imac 20 (2009 model)

    *Hi i have a APPLE MB417B/A iMac 20" MB417B/A*
    *what ram do i need? how much ram can i get? 4g? or 8g?*
    specs are as follows:
    With a 2.66GHz Intel Core 2 Duo processor, 2GB DDR3 RAM & NVIDIA graphics, iMac brings you more performance than ever. iMac packs performance inside a stunning all-in-one design. Includes Mac OS X.
    * 2.66GHz Intel Core 2 Duo Processor
    * Mac OS X v10.5 Leopard - Operating system
    * 2GB Memory - Run more applications
    * 320GB Hard Drive - Load up on photos,videos
    * 20'' Widescreen display - Vivid colours
    i'd be greatful for any help...

    Hello miss_papaya
    That model supports 2 4GB modules for a total of 8GB, only problem is that 4GB modules are currently at a premium price. Have a look at the spec's in the following article or in the User's Guide that came with your iMac.
    http://www.apple.com/imac/specs.html
    Also have a look at Crucial and OWC memory below:
    4GB kit > http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=60D83BBCA5CA7304
    8GB kit > http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=1D7DBABCA5CA7304
    OWC > http://eshop.macsales.com/shop/memory/iMac/DDR3_2009
    Dennis

Maybe you are looking for

  • Lumia 720 screen freezes

    I am facing a touch problem on my nokia lumia 720. it freezes the screen when i press power key it gets back to normal. I have already hard reset the device. but the problem happens randomly so i cant show to nokia care representatives.

  • Problems with Gaming

    Alot of games including a important game Planetside 2 i have problems with as soon as i dl windows 10. My info Graphics card-NVIDIA Geforce GTX 650     processor- AMD FX(tm)-8350 Eight-Core Processor 4 GHz      System type- 64-bit                    

  • Accessing RFCs and BAPIs from enterprise java beans

    Hello folks,      my question is concerning comunication between EJBs and RFCs. I want to develop a simple session bean that connects to a R/3 back-end, calls a RFC then returns some data, let's say, an example of this could be a list of employees fr

  • Can't zoom in/out on one site

    Sorry for my bad egnlish. I have an iPhone 3Gs. I bought it 2 months ago. And two days ago i went to site "http://maps.yandex.ru/" (i needed it, not google maps) and all was working. I could zoom in/out in maps. But on the second time (in 5 hours app

  • [makepkg] Question about split packages handling in makepkg

    Hello One question came to my mind, while I was looking at the vlc PKGBUILD. Does splitting packages have to be done in such a non efficient way? I mean, why do we have to delete for example, a directory, once make install has been issued, only to co