How the cluster works when shared storage disk is offline to the primary ??

Hi All
I have configured Cluster as below
Number of nodes: 2
Quorum devices: one Quorum server, shared disks
Resource Group with HA-storage, Logical host name, Apache
My cluster works fine when either the nodes looses connectivity or crashes but when I deny access for primary node ( on which HA storage is mounted ) to the shared disks.
The Cluster didn’t failover the whole RG to other node.
I tried to add the HAstorage disks to the quorum devices but it didn’t help
Anyways i can't able to do any i/o on the HAstorage on the respective node
NOTE:This is the same case even on Zone cluster
Please guide me, below is the O/P of # cluster status command === Cluster Nodes ===
--- Node Status ---
Node Name Status
sol10-1 Online
sol10-2 Online
=== Cluster Transport Paths ===
Endpoint1 Endpoint2 Status
sol10-1:vfe0 sol10-2:vfe0 Path online
--- Quorum Votes by Node (current status) ---
Node Name Present Possible Status
sol10-1 1 1 Online
sol10-2 1 1 Online
--- Quorum Votes by Device (current status) ---
Device Name Present Possible Status
d6 0 1 Offline
server1 1 1 Online
d7 1 1 Offline
=== Cluster Resource Groups ===
Group Name Node Name Suspended State
global sol10-1 No Online
sol10-2 No Offline
=== Cluster Resources ===
Resource Name Node Name State Status Message
global-data sol10-1 Online Online
sol10-2 Offline Offline
global-apache sol10-1 Online Online - LogicalHostname online.
sol10-2 Offline Offline
=== Cluster DID Devices ===
Device Instance Node Status
/dev/did/rdsk/d6 sol10-1 Fail
sol10-2      Ok
/dev/did/rdsk/d7 sol10-1 Fail
sol10-2 Ok
Thanks in advance
Sid

not sure what you mean with "deny access" but could be reboot of path failures is disabled. This should
enable that:
# clnode set -p reboot_on_path_failure=enabled +
HTH,
jono

Similar Messages

  • In my wife's window, the sound works, when I switch over to my window the sound doesn't work.  I noticed the problem when I went to a YouTube video.  How do I correct this?

    In my wife's window, the sound works, when I switch over to my window the sound doesn't work.  I noticed the problem when I went to a YouTube video.  How do I correct this?

    Hello Kiira Doon,
    The troubleshooting steps detailed below may help get your iPhone's display to function.
    Toggle the ringer switch to see if the unit vibrates. If it does, it could be that iPhone is getting power, but is not displaying any image.
    Try turning iPhone off and then on again.
    While connected to the iPhone charger, try to reset the iPhone.
    If the low-battery screen appears, charge the iPhone.
    My issue is still not resolved. What do I do next?Contact Apple Support.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Cheers,
    Allen

  • Disk utility will not boot using COMMAND   R. It won't give me the 'ERASE' option when I open Disk Utility. How do I wipe my hard drive?

    Disk utility will not boot using COMMAND   R. It won't give me the 'ERASE' option when I open Disk Utility. How do I wipe my hard drive?

    If you're truly running 10.6.8, there is no Recovery partition - that didn't come along until 10.7x.
    You'll need to use the set of gray discs that originally shipped with your model. If you don't have them, you can always get your serial number from the bottom of the casing and call Apple to get a set of replacement discs. These will run you about $20 + shipping & taxes. Once you have the discs, boot from Disk One and use Disk Utility to erase your HD and then reinstall whichever version of OS X that shipped with your model. No way around of getting the discs.
    Clinton

  • 10g RAC on varitas Cluster Software and Shared storage

    1. Install oracle binaries and patches (RAC install)
    2. Configure Cluster control interface (shared storage) for Oracle
    3. Create instances of oracle
    These are 3 things i am wondering how to handle, I did all these on Oracle Clusterware , but never on Veritas Cluster ware ...all these 3 steps are the same or different. In someone can help..

    How we can do this while using varitas cluster software
    1. Install oracle binaries and patches (RAC install)
    2. Configure Cluster control interface (shared storage) for Oracle
    3. Create instances of oracle
    If we install RDBMS 10.2.0.1 with standard installer it will catch the vcs and when we will be running dbca it will ask for RAC db option?
    what is Configure Cluster control interface (shared storage) for Oracle??

  • My ipad recognizes my home network but will not connect to the internet. When I click on AirPort/preferences at the top of the imac screen it says..."AirPort has a self-assigned ip address and may not connect to the internet".How can I change ip address?

    My ipad recognizes my home network but will not connect to the internet. When I click on AirPort/preferences at the top of the imac screen it says..."AirPort has a self-assigned ip address and may not connect to the internet". If this is the root of the problem,how can I change ip address?
    Ipad will connect no problem to other networks.

    First thing you need I think is to get your iMac connected to the Internet.
    Shut down your iMac and you iPad. Then power off your router. Wait 30 seconds and power up the router.
    After the router indicates that it is connected to the Internet then start up your iMac and see if it connects. If the iMac connects to the Internet then your iPad should too.
    If this power up sequence doesn't work you'll have to dig into the router setup to make sure it is working properly.

  • My sound has recently gone on my Iphone4s, this only happens when I use my phone myself. The sound works when I receive calls and texts but I am unable to watch videos, listen to music etc it seems like my volume button has gone! Can anyone help??

    My sound has recently gone on my iphone4s, this only happens when I use my phone myself. The sound works when i receive a call or a message etc but I am unable to watch videos or play music, the sound also doesn't work on games. Please can anyone help with this issue or let me know how to fix it if experienced the same problem?

    Remove all apps from multitasking bar. Double click Home button then tap and hold an icon and tap on little x on every app. Then reset. Hold down Home and Power button until Apple logo appears.

  • Trying to get my fcp project to burn to dvd at the highest quality? Ive used compressor and then tried to put it in dvdsp put its not working. I am having problems with the audio or when i burn it , i cant play the dvd? any help would be appreciated

    Ive used compressor and then tried to put it in dvdsp put its not working. I am having problems with the audio or when i burn it , i cant play the dvd? any help would be appreciated

    I suspect you are attempting to burn an HD DVD, which will not play on a DVD player...
    But if you provide more details such as the settings you are applying in Compressor, then we would be able to provide you more accurate information.
    How are you adding the files to Compressor?
    In FCP, what are your footage properties (command-9) and sequence settings (command-0)

  • I have a Win7Pro SP1 PC locked down with a Group Policy as it is a public facing PC. PDF fillable forms cannot be completed when logged on as the restricted user. The forms work as a normal user. What are the user requirements/permissions needed to fill f

    I have a Win7Pro SP1 PC locked down with a Group Policy as it is a public facing PC. PDF fillable forms cannot be completed when logged on as the restricted user. The forms work as a normal user. What are the user requirements/permissions needed to fill forms?

    Well, try this (I was able to fix my with these steps):
    Go Utilities > Disk Utility
    Select your Startup Disk, e.g. Macintosh HD
    Then, under the First Aid Tab, click Verify Disk Permissions.
    If there are errors, then click repair Disk Permissions.
    After it is done, restart the computer and see if your problem is resolved.
    I hope this help.
    Zeke
    www.ZekeYuen.com/blog/

  • Using Flach CS4 and action script 2.0 how do I advance to a specific frame of the main timeline when a movie clip instance come to the end of its timeline?

    Using Flach CS4 and action script 2.0 how do I advance to a specific frame of the main timeline when a movie clip instance come to the end of its timeline?

    code on the last frame of your movieclip instance:
    _root.gotoAndStop('whatever_frame');  // will work unless this swf is loaded into another swf.  in that situation, you should use a relative path to the main timeline (eg,  _parent or _parent._parent etc).

  • How DB adapter works when polling strategy is "remove row selected"?

    How DB adapter works when polling strategy is "delete the rows that were read"?
    I want to know how database adapter works when polling startegy is "remove row".This polling strategy helps for polling the changes to table and remove records after new records are inserted or changes are done to table.Here,i want to understand how DB adapter identifies which record to be deleted.
    For example: there is a table with 100 recorrds.How DB adapter works when polling strategy is "delete the rows that were read"?
    I want to know how database adapter works when polling startegy is "delete the rows that were read".This polling strategy helps for polling the changes to table and remove records after new records are inserted or changes are done to table.Here,i want to understand how DB adapter identifies which record to be deleted.
    For example:
    There is a table EMP with 100 recorrds.Now, i deploy a BPEl process with db adapter polling on table EMP for changes.So that ,if any change happen to records in table that records will be picked up.I use a polling startegy "delete the rows that were read" .
    Now i insert 9 new records and update one existing records.These 10 records should be picked up and then deleted by Db adapter.In this 109 records how DB adapter identifies these 10 records when it polls.How it differentiatess old records with new records when there is no flag field or no sequence id used to identify the new or modified records.
    Please let me know.
    Why i want to know this?
    Some times customer may not allow BPEL process to do any modifications to source table or source database.In this case the options provided by database adapter wizard are not useful.
    If there is any mechanism to identify new or modified records without having a FLAG field or sequence table,then it is possible to have an option like only read the changes from table rather than deleting the records after reading.Which helps in meeting above requirement.
    Please let me know if there is any way to do this.
    thanks
    Arureddy

    Once the record has been read it is deleted. Therefore, you can update rows in this table as many times you like before it is read. Once it is read there will be nothing to update as it will be deleted.
    If you don't want to use a sequence table, you can use a sequence file. You can only use this functionality if the key you are using increments sequentially. e.g. 1,2,3,4. If your key is random, e.g. 2,1,3,5,7,4 then your options are delete or use a processing flag.
    The other option is to create a trigger that inserts a key into a polling table when insert or updates occur. You can then use the delete, which is the most desirable as it uses database locking.
    cheers
    James

  • TA38556 I am trying to set up my apple tv using the hospital network. I am able to detect the network and chose it. But the way the system works is that you have to agree to the terms and conditions of using their network. How do I accomplish this with ap

    I am trying to set up my apple tv using the hospital network. I am able to detect the network and chose it. But the way the system works is that you have to agree to the terms and conditions of using their network before access the internet. How do I accomplish this with apple? Please help.

    There are some other options to you, if you're not at home and nobody is using your router you could set it up at the hospital, if this isn't an option you could get a second router and use it.  Many ethernet routers are available on the cheap, and ethernet cables are cheap too.
    Also, a macbook can share it's internet via the built in wifi it has.  See this go to settings-sharing-internet sharing and configure as desired.  This may require an internet connection via ethernet.  But you should be able to create a wifi network for using something like airplay/home sharing.

  • Why the -- dont work when i am logged in on linux terminal.

    Why the <-- dont work when i am logged in on linux terminal.
    when i press <-- (left) when i am logged on sqlplus on linux i only get
    SQL> ^[[D
    please tell me how i change this..
    hugs Gökhan

    Why the <-- dont work when i am logged in on linux
    terminal.Is "<--" your "Backspace" key or the "left arrow" key ?
    On the command line:
    1. If you want to set your "Backspace" key to delete the previous character, then run this:
    $ stty erase ^H
    2. For the "left-arrow-key-not-working" issue, you may want to try this:
    $ stty sane
    hth,
    pratz

  • W530 - How does things work when having two graphics cards?

    So I have a W530 with an Intel HD Graphics 4000 and a NVIDIA Quadro K2000M.
    How does things work when the computer has two graphics cards? I mean, is only one active at a time? Or is one doing complex calculations while the other one might be the one displaying them on the screen?
    Related question:
    I just bought and installed the game Portal 2. How do I know if it is using the better graphics card (NVIDIA Quadro K2000M)? And if it is not, how do I configure Windows, Steam or Portal 2 to use it to its full potential?

    Technically, the Intel integrated graphics is always active, although it is not always in use. Nvidia graphics will turn on and off according to need. Software from Nvidia called Optimus automatically switches between integrated (Intel) and dedicated (Nvidia) graphics, according to the application. Portal 2 will run smoothly at maximum settings and native 1920x1080 resolution using the K2000M. The easiest way to see which graphics card is in use is to check the "Display GPU activity icon in notification area" option in the Desktop menu of the Nvidia control panel. It should automatically use the Nvidia graphics card when Steam is running. If it does not, you can add Steam to the program settings in Nvidia control panel and select that it should always use the Nvidia graphics.
    Also, if you are using an external monitor and the notebook monitor, then you will be using both graphics cards - the Intel graphics will drive the notebook screen and the Nvidia card will power the external display(s).
    Thinkpad W530, i7-3720QM, 1920x1080 screen, 32GB RAM, dual SSDs (Samsung 830, Crucial M4 mSATA), Quadro K2000M, 9-cell battery, DVD burner, backlit keyboard, Bluetooth, Intel 6300 wireless card

  • HT203172 my dvd player is not working when i try disk U  i get this massage  Warning: SUID file "usr/libexec/load_hdi" has been modified and will not be repaired.


    my dvd player is not working when i try disk Utility  i get this massage  Warning: SUID file "usr/libexec/load_hdi" has been modified and will not be repaired.

    Is this bad?
    No. Ignore it.
    What does this mean?
    That you have the current OS version installed.
    As far as I know, I have not installed any Remote Access software on my Mac.
    It's part of the OS.
    (55800)

  • My iPhone was stolen and I have contacted the police who are using the meid number to locate.  How does this work and what are my chances of getting the phone back?

    My iPhone was stolen.  I used Find My iPhone app to lock it and display a message.  The phone has not connected to the internet to locate it.  I contacted the police and they have taken my meid number.  How does this work and what are my chances of getting the phone back?  Are there other ways the theif can use it.  I was told once they put in a new sim card and use it, whatever software the police have, it will show up.

    Honestly? In the US (I can't speak to other countries, though I doubt it works much differently in a lot of the world) The police took your report and filed it either in their computers or, on paper. They will now not think of this again. The only time it will cross anyones mind is if, in the course of entering information into evidence about items recovered or seized at a crime scene, the serial number of an iPhone that was found/seized happens to match yours, in which case you will be contacted.
    The police in the US can and will do nothing to 'blok' the phone and it's not worth their time to try and locate it unless you know for a fact that it was stolen by a big time drug lord, master criminal, or some other such prime target and they can get a court order to track the location of the phone in order to locate this individual for your own purposes.  If they do that, they'll probably keep him under surveilance for a year or so before they act.
    Basically, the police don't care about your phone. If they find it, they will give it back to you. They are not, however, going to go looking for it. They have better things to do.
    I'm sorry, but that's the way it is.

Maybe you are looking for