How the heck do i get a firmware upgrade from my computer to the router?

I went to this site here to try and make my router work. It is a WRT54GS wireless router, and I saw where i could download some firmware upgrade, so I clicked on it and saved it to my desktop. It is a .bin file. Now how do I get that file to the router?????
The router was working until today and now it isn't sending out a wireless signal. However, it is still connecting my computer to the internet through its wire (modem to router, router to computer with cable). But when I open the Easylink software, it says that the internet connection is not working, even though the little green light is on for "wireless" on the front of the router.
But anyway, how do I get this downloaded file onto the router??? There isn't any usb ports on the router to connect to it. There isn't anything in the Easylink software that gives me that option, or if there is they hid it pretty good. They really should explain how to do this, or do they expect everyone to have a degree in networking or computers or something? I need some help here 

As sabretooth suggested,Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now,Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Similar Messages

  • SPA112 firmware upgrade from 1.0.1 to 1.2.1 kills the SPA

    I took a brand-new, unconfigured SPA112 out of the box, plugged it into DHCP-enabled network, noted it was running v1.0.1 firmware and attempted a firmware upgrade to 1.2.1 via the web management utility.
    After reporting a successful upgrade there was no further response from the SPA112 to HTTP requests, neither was there any response to pings. ARP requests are responded to successfully. The IVR works (as well as the IVR ever works) until I selected to perform a factory reboot at which point the IVR stopped responding as well. Holding the reset button for 20sec does nothing useful. It's dead, Jim.
    I've had this experience on another SPA112 as well under similar circumstances although there is nothing in the Release Notes for v1.2.1 to say that such an upgrade does not work.
    My questions:
    1)Is there any way of recovering these devices or do I need to send them back to Cisco?
    2) How am I supposed to perform such a firmware upgrade?

    Hi Matthew,
    I tried upgrading the firmware upgrade from v1.0.1 to v 1.2.1 and I had the same problem. The device just stopped responding. I tried that in a lab and I figured out what exactly to do when you get in to a problem like that. So lets start off once again.
    Snce SPA112 must get an IP first through a DHCP on WAN port. Connect the SPA 112 device according to the instructins told in this article till the step 3.
    http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2775
    Once you access the web GUI of SPA112 follow the contents of the following article and upgrade the firmware
    http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2676
    In your case I believe the window got stucked at the point when it says "The upgrade is successful" and then there was no further response to HTTP requests.
    Restart the device and see if it works or not. If it does not then log in to the router web GUI and navigate to the ARP table and see what are the VLAN assigned to the IP address.
    NOTE: Both the router and SPA should be in the same VLAN. This way only the device will respond to the HTTP requests. If they are in a different VLAN's, navigate to the VLAN and disable the LAN memberships. For example there are two VLAN ID 1 and 100. Disable the LAN ports for the ID 100 and only enable it for 1.
    Navigate to the ARP table again and refresh it. Both the IP addresses should be in the same VLAN. If yes. Access the SPA112 with an IP address assigned to it again and navigate to Administration > Firmware Upgrade. You will see the firmware of the device has been upgraded.
    (optional) Upgrade the firmware again. This time, it will go through and the device will restart.
    Let me know if you still need any help. 

  • How to I get library songs upgraded from 128k to 256k

    How to I get library songs upgraded from 128k to 256k. That is the reason I signed up for match in the first place.

    Upload all your music to iTunes Match. Now that all your music is in iCloud iTunes Match service. You can now delete all your current music on your computer. Now download all the music from the iCloud and your music will be 256k. That is for PC or Mac.
    On your iPhone, as soon as you download the music to your iPhone. The songs will be 256k.

  • I have removed every possible componet of Mozilla Firefox from my computer and I still get a message when I turn on my computer that Firefox had a problem and needed to close. How do I get this completely removed from my computer?

    I have removed every possible componet of Mozilla Firefox from my computer and I still get a message when I turn on my computer that Firefox had a problem and needed to close. How do I get this completely removed from my computer?

    See:
    * http://kb.mozillazine.org/Profile_backup
    You can transfer files from the old profile to that new profile (be careful not to copy corrupted files)<br />
    See:
    * http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

  • How can get 40,000 pix from old computer restored by Carbonite to new computer into PE 11 or 12?

    I bought a new,  faster, more storage Windows 8 computer.
    I had 40,000 pix on old computer tagged with names, event, location, date with PE 11. Also several projects involving hundreds of pix.
    Carbonite restored all files (250 gig) from old computer to new, and their tech support says they all are on the new computer.
    I bought the new PE 12 and installed it on new computer.  It has only found 4,000 pix.  I don't at all like PE 12 after enjoying PE2-11 and managing all my  pix with it.  PE11 was clearer in the pix presentation.
    Apparently when imported to the new computer, I lost the tags that went to events, location, and the person tags did not  separate family from friends etc.  I can't even find my projects.
    I was so frustrated with PE12, that I installed PE11, but everytime I try to open the Organizer, it doesn't open.
    Help.  I am so frustrated.  I am pretty sure  before I made the transition that I had written all tags to files.  When I put PE11 on the new computer, why won't it give me what I had on the old.
    This is probably my 10th generation computer change, and I never had such problems before with PE.

    I am using 10 and 11 instead of 11 and  12.  I tried to go back and edit,
    but couldn't figure out how.  Sorry,  typing errorC.
    In a message dated 2/6/2013 7:02:33 P.M. Eastern Standard Time, 
    [email protected] writes:
    Re:  How can get 40,000 pix from old computer restored by Carbonite to new 
    computer into PE 11 or 12?
    created by Jeff A Wright (http://forums.adobe.com/people/JeffAWright) 
    in  Photoshop Elements - View the full  discussion
    (http://forums.adobe.com/message/5050443#5050443)

  • How to get back voice memos from my computer

    Hello, is there any way to get back voice memos from my computer? please help, very urgent, thank you in advance:)

    The only method I know of is software called iexplorer.  After downloading the program onto your computer, open explorer and navigate to your phone and you will see the voicemails.  Copy them to your computer and your all set.  Sorry for your loss

  • Can I get a free upgrade from photoshop elements 11 to the 13? I have 11 and my laptop is 64 bit. registered software bought aug 2013

    Can I get a free upgrade from photoshop elements 11 to the 13? I have 11 and my laptop is 64 bit. registered software bought aug 2013

    There is no free upgrade. You have to buy it.
    Mylenium

  • I have Safari 5.1.10 Browser and keep getting notices to upgrade from my bank.  What is the best upgrade?

    I have Safari 5.1.10 Browser and keep getting notices to upgrade from my bank.  What is the best upgrade?

    Upgrading to Yosemite
    You can upgrade to Yosemite from Lion or directly from Snow Leopard. Yosemite can be downloaded from the Mac App Store for FREE.
    Upgrading to Yosemite
    To upgrade to Yosemite you must have Snow Leopard 10.6.8 or Lion installed. Download Yosemite from the App Store. Sign in using your Apple ID. Yosemite is free. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
        OS X Mavericks/Yosemite- System Requirements
          Macs that can be upgraded to OS X Yosemite
             1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
             2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
             3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
             4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
             5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
             6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
             7. Xserve (Early 2009) - Model Identifier 3,1 or later
    To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
         Are my applications compatible?
             See App Compatibility Table - RoaringApps.
    Upgrading to Lion
    If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
    You can purchase Lion at the Online Apple Store. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
         Lion System Requirements
           1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
               or Xeon processor
           2. 2GB of memory
           3. OS X v10.6.6 or later (v10.6.8 recommended)
           4. 7GB of available space
           5. Some features require an Apple ID; terms apply.

  • How do I transfer music, videos to my iPhone from another computer that is not the one my iPhone syncs with

    How do I transfer music, videos to my iPhone from another computer that is not the one my iPhone syncs with.
    Thank You!

    Take a look at this -> Recovering your iTunes library from your iPod or iOS device
    Short version: iTunes will transfer the purchases made from the iTunes Store on your iPhoneh to your computer. It treats all other music and video syncing as a one-way street, to comply with copyright laws (wont sync stuff not purchased through iTunes from your iPhone to your computer).

  • Help me please going crazy, I have my Iphone 4S getting my e-mails from my computer using outlook but when I delete yhem on my computer they stay on my phone, I am syncing via the cloud, Is there a setting that stopps this e-mail from growing on my phone?

    Help me please going crazy, I have my Iphone 4S getting my e-mails from my computer using outlook but when I delete yhem on my computer they stay on my phone, I am syncing via the cloud, Is there a setting that stopps this e-mail from growing on my phone?

    For outlook or hotmail emails they use a pop server technology that you can't sync your computer and your iPhone with. You have to unfortunately delete the emails from both devices. It is super frustrating but that is the only way.
    Hope this helps.

  • How can I transfer some of my iTunes songs from my computer to my husband's iPhone who has a different apple ID.

    How can I transfer some of my Itunes songs from my computer to my husband's iphone?  He has a different apple ID and every time I do this, my IMac says it will erase and sync.  I've checked the manual manage box but no luck.

    turkofrome wrote:
    It says that his computer is authorized, but as soon as I try to transfer anything, I get a message saying that my iphone is already synced with another iTunes library
    What does the iPhone have to do with anything?
    Don't plug yoru iPhone into his computer.
    Do I need my iPhone to do it or can I do it from iMac to iMac? Thanks for any help.
    So you have two different computers?
    Just enable Home Sharing and he can copy the songs from you iTunes to his then he can sync his iPhone to his iTunes.
    See this -> http://www.apple.com/support/homesharing/

  • How can I transfer my iTunes library and playlists from one computer to another?

    How can I transfer my iTunes library and playlists from one computer to another?

    Copy the iTunes folder (Mac: Home\Music or PC: My Music) to the same location on the new computer. If an iTunes folder already exists on the new computer (it will on a Mac) replace it with one you copied.

  • Firmware upgrade from 2.1(3a) to 2.1(3b).

    I don't find any documentation on the web for firmware upgrade from 2.1(3a) to 2.1(3b)..
    is it wise to follow this link http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/upgrading/from1.4/to2.1/b_UpgradingCiscoUCSFrom1.4To2.1.html
    Any best practices ?

    I would consult
    http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2.1/b_GUI_Firmware_Management_21.pdf
    Cisco UCS B-Series GUI Firmware Management Guide, Release 2.1First Published:
    Last Modified: July 12, 2013November 16, 2012

  • How can I transfer all my music and apps from my computer to my new iphone?

    how can I transfer all my music and apps from my computer to my new iphone?

    This is one of the most basic of functions of the iPhone.  This is a good time for you to read the User Guide.  All the instructions on how to operate yor phone are included.  I suggest you read through it.
    http://manuals.info.apple.com/en_US/iphone_user_guide.pdf

  • How can I deactive software for Photoshop Elements 10 from my computer.

    How do i deactivate software for Photoshop elements 10 from my computer. Help does not appear to have a deactivate command

    If you have the mac app store version, there's no need to deactivate.

Maybe you are looking for

  • Is third-party SO/PO  process possible using only one company code?

    Hi friend, 1) my client wants to implement third-party PO process but also wants a way of keeping track of inventory during this process. I know that inventory should be tracked on the vendor side and not on our client side since we're doing third-pa

  • Proxy to Mail Adapter issue

    Hi Experts, I have a requirement like a control report is comming from SAP through proxy to XI and I need to send that control report as an attachment in excel format from XI to the 3rd party by the mail adapter.Also in the mail body I have to send t

  • Display Table Headings in 4 Layers..

    Hi All, Please help me in displaying the table heading in four layers.. layer1 | X | Y | Z | layer2 | heading 1 | heading 2 | heading 3 | Heading 4 | Layer 3 | col name 1 | coln 2 | cl 3 | col 1 | heading 0 | col 1 | heading 0 | heading 1 | Layer 4 |

  • Fading between multiple customer comments - scalability issue

    I am completely new to Flash and have been learning about alpha tweening to fade one .jpg image (of a customer's happy comment) to another.  This works fine if I only have a small number of comments, but modifying each and every stage of the transiti

  • How to track keystrokes

    Hi, I would like to know how to create an background application which can track keystroke as we are creating an application which records the ppt slide change time. And this log we are going to use it for another javaFX application. Thank you in adv