How to access the pendrive on my Airport Extreme via my iPhone 3GS?

I connected a pendrive on my Airport Extreme.
After connecting my Mac to the Airport Extreme it showed the pendrive.
But when i connected my iPhone to the Extreme it did not show the pendrive.
Is there any app or way that I can view or acces my pendrive on my iPhone?

Try an App like FileBrowser from the App Store.

Similar Messages

How to extend the range of my Airport Extreme network by adding an Airport Express

How to extend the range of my Airport Extreme network by adding an Airport Express?

You have to make sure that the AirPort Express is in Factory Default Settings. If it is straight out of the box, it is ready to be configured.
The instructions that I will provide are for using AirPort Utility 6.0, which you have.
Locate the Express in the same room as the AirPort Extreme for the configuration. Power it up and allow a full minute for the Express to display a blinking amber light.
Make sure that the wireless is turned on your Mac
Open AirPort Utility 6.0 and look at the small rectangle in the upper left hand corner of the display. It should now read something like "Other AirPort Base Stations (1)"
Click on the rectangle, and then click on the AirPort Express xxxxxx listing
AirPort Utility will take a minute or two to analyze the settings on your network and then suggest that the Express be configured to "Extend" your wireless network.
Edit the Base Station name to your liking, then click Next in the lower right hand corner
Allow a full minute or two let AirPort Utility do its work
When you see Setup Complete, click Done at the lower right of the window.
Now move the AirPort Express to a location that is approximately half way between the AirPort Extreme and the area that needs more wireless coverage.
You should be in business.

How to access external drive attacked to AirPort Extreme from ipad

Have attached external drive to AirPort Extreme via USB, how can I access those files from iPad / iPhone?

Check to see if the File Browser App can do this:
App Store - FileBrowser - Access files on remote computers

How to disable the wireless section of Airport Extreme Base Station?

Is it possible to disable the wireless section of Airport Extreme Base Station?
It is because I do not want to have any high frequency radio signal which may be dangerous for small baby (no such proof for the moment, however).
Anyone using the new Airport Extreme Base Station please check and help.
Thanks!!

I think you are a little too concerned. Just for the sake of how to, here it is.
go to manual set up, airport, wireless, wireless mode, and then choose off.
good luck.

Looking for the steps to configure remote access to HD connected to airport Extreme via Surfboard modem

I found an article that seemed a little dated outlining steps on how to access files on my exteral hard drive that is connected to my airport extreme. I have enabled personal file sharing, specified the ports and put in the internal IP address. To test, I am connecting to VPN on my ipad, firing up a browser and trying to navigate to the external IP address and port number specified (xxx.xx.xxx.xx:xxxx) I keep getting a page cannot be displayed error. Any suggestions?

Test from a real WAN connection.. not a loop around via vpn. as it is hard to know where the problem is.. is it the vpn or the port forwarding.
Also it is hard to test from ipad as the only effective protocol to use is AFP on 548 and ipad is not able to do it.
Read Tesserax info on remote access.
https://discussions.apple.com/docs/DOC-3413

HT4145 how to connect the i pod to airport extreme

I am trying to figure out how to connect to my airport extreme from my ipod- anyone who can give me a stepby step answer?
I am not sure which operating system it is...
Thanks!

If the AirPort Extreme is allowing other devices to connect, it is not the issue.
Follow the iOS Troubleshooting Guide for Wi-Fi Networks and Connections
http://support.apple.com/kb/TS1398
You will be better served to post in the iPod support area for questions about the iPod. Post here:
iPod

How can access hours be restricted with airport extreme

I want to be able to stop my kids from accessing the internet and bogging things down during the day when working from home. Is there an easy way to do this with an Airport base station network or by setting up a guest network? I have tried using parental controls but that limits all computer use, not just online access hours. Any help would be appreciated.

You do have a number of choices available to you to restrict access, either completely through AirPort's Access Control, or limiting what they will be able to access on the Internet. If your goal is to restrict them from particular sites or categories of sites, like P2P sharing torrents, one option is to use OpenDNS as your DNS provider. Through their service, you can easily configure what they can access or not.

How do I configure port forwarding on Airport Extreme via Win 7/64?

Hello all,
I'm trying to forward some ports in order to correct issues with setting up servers for video games, i.e. I can connect but another can't while yet another can connect fine, etc. So far, despite thorough Google searching, I have not been able to find a solution that matches my exact problem.
The specific ports I want to forward are 7777 and 25565. Currently, my connection is through Northstate Communications using an ADSL modem/router (Zhone Model No. 6218-I2-200-0NS) hooked up to an Airport Express + Time Capsule (Model No. A1254, version 7.5.2). As far as I know, the only reason the Airport Extreme is there is for the time capsule, but I don't know for sure whether my computer is actually connecting to the internet through one or through the other. I didn't set it up originally, unfortunately.
I currently can't edit the settings for the Zhone. Supposedly, typing 192.0.0.1 into the address bar of my web browser should open the router configuration utility, but instead it returns "Oops! Google Chrome could not find <address>." I can, however, use the AirPort Utility for Windows to edit all of the AirPort's settings. I have followed the instructions in this YouTube video to forward the port 7777 using the AirPort Utility: http://www.youtube.com/watch?v=OFad6NvddRk but changes I make to Advanced/Port Mapping apparently do not work because www.whatsmyip.org and www.canyouseeme.org report that a test of port 7777 is either timing out or unavailable, respectively.
I am concerned that the IP address automatically provided for me when I create a new port mapping is not the correct IP address since it is 10.x.x.x, which I can't find anywhere in any settings on the computer or online. But, when I type in the IP address I get from www.whatsmyip.org (97.x.x.x) and then go back to edit the setting I created, it has apparently reverted to 10.x.x.x without saving the address I entered.
So, what am I doing wrong? Do I need to change some settings in the Zhone router before it will work, and if so, how can I access it? What is the 10.x.x.x address that the AirPort Utility assigns to new port mappings by default? Since I intend to use Hamachi to host the game server, do I need to use the IP address given to me by that program (5.x.x.x) instead? As far as I can determine, all my drivers are up to date. Any assistance would be much appreciated. Other system specs given below:
CPU: AMD Phenom II X4 945 3.00 GHz
MB: MSI 790FX-GD70 AM3 AMD
RAM: Corsair Dominator 4GB (2 x 2GB) 240-Pin DDR3 SDRAM 1600 (PC3 12800)
Mushkin Enhanced Blackline 4GB (2 x 2GB) 240-Pin DDR3 SDRAM 1333 (PC3 10666)
GPU: Sapphire 100258-1GHDMI Radeon HD 4850 1GB 256-bit GDDR3 PCI Express 2.0 x16
Wireless: AZiO AWD102N PCI Wireless Adapter
OS: Windows 7 64-bit
-R

Thanks for your response. I attempted to do that, but I couldn't find any way to access the configuration for the Zhone router. Typing the IP address into my web browser's address bar only resulted in "page could not be found" or "page timed out", etc. I called tech support at Northstate, who likewise suggested that the Zhone router should be set to bridge mode and the AEBS set to router mode since it would be easier for me to configure the AirPort. After wrangling a bit with them over my inability to change any settings for the Zhone, they sent a technician over. He messed around with the Zhone, apparently putting it in bridge mode, and we managed to get the AirPort to work without any double NAT errors. I reset the AirPort and created a new configuration file. Unfortunately, when I went to the Advanced/Port Mapping menu and repeated the original steps to forward port 7777, tests at www.whatsmyip.org still returned "timed out". The technician said he wasn't knowledgable enough about Apple products to assist me any further and suggested I call their tech support or visit the nearest Genius Bar. So that's about it. Any other ideas?

How to access the "Genre", "Artist", and "Album" Panel via COM/script

I thought I posted this a couple of days ago, but checking on "My Posts", it appears I didn't. Oooops
I'm using the COM interface, which is also same as the scripting one.
I'm trying to discover what elements in the iTunes main window have been selected, and thus "highlighted".
The main window appears, to the interface, to be the "BrowserWindow", not to be confused with the View -> Show Browser window. Within this main window, I can identify which Playlist is currently selected, and/or which individual tracks are selected.
But, what I'm trying to do, is also identify if any elements in the View -> Show Browser window are also selected. "Genre", "Artist", and "Album".
Does anyone know if this is possible, and if so, how do I achieve it.
Cheers,
Eddie

In case you don't get any replies here, Eddie (your post might get buried under queries about iTunes 7.7), it might also be worth checking in at Teridon's google discussions. Robert's post here has a link through to those:
http://discussions.apple.com/thread.jspa?threadID=1584683&tstart=30
(Robert is the person I think of immediately in the context of scripting issues.)

I have an Ipad, I activated the time capsule with no issues. I added the airport Utility application without issue. However, I do not know how to access the hard drive with either my Windows computer or the Ipad. Does someone know how?

I have an Ipad, I activated the time capsule with no issues. I added the airport Utility application without issue. However, I do not know how to access the hard drive with either my Windows computer or the Ipad. Does someone know how?

On windows load the airport utility .. latest correct version as possible.. there is no windows 8 but win7 works after a fashion.
Make sure the TC is using SMB compatible names.. short no spaces and pure alphanumeric.
Type the name directly into windows explorer.
\\TCname or \\TCIPaddress
If no luck turn off all the firewalls.. internal windows plus security software plus whatever other gargyoles and other rubbish AV software you have running.
Ensure windows is able to at least ping the TC by IP address and name..
Use the utility in windows to set file sharing to guest account on with full read and write access.. and set workgroup to WORKGROUP.

How do I access external hard drive connected to AirPort Extreme via iPad

Hello,
How do I access external hard drive connected to AirPort Extreme via iPad / windows laptop.
I donot have a Mac and I use windows laptop.

For your iPad, you will need an app, like FileBrowser, to access the external drive.
For your Windows laptop, you would access the drive like any other network share. The basic format is: \\<servername>\<sharename>, where, in this case, the servername is the base station name and the sharename is the name of the external drive.

How can I access my HD files connected to my airport extreme thru my iPhone?

How can I access the files stored on my HD that is connected to my airport extreme thru my iPhone?

You might want to check out Filebrowser. More info here:
http://www.stratospherix.com/products/filebrowser/

In VB Programming code -- How to access the formula for suppressing a field

In VB Programming code -- How to access the formula for suppressing a field
I am using Crystal Reports 2008 v1
Using VB code, I am attempting to modify a Crystal Report before exporting it into a PDF format and then displaying it on the Web.
My problem is that I am unable to access the formula used to dynamically suppress a field.
The following code is working:
mySections = rd.ReportDefinition.Sections
For Each mySection As CrystalDecisions.CrystalReports.Engine.Section In mySections
   ' myFieldToChange is a String set to the text of the field I need to adjust the Suppression
   iloop = 0
   For Each RecObj As CrystalDecisions.CrystalReports.Engine.ReportObject In mySection.ReportObjects
           If mySection.ReportObjects.Item(iloop).Name.ToLower = myFieldToChange Then
               myTextObject = CType(mySection.ReportObjects.Item(iloop), CrystalDecisions.CrystalReports.Engine.TextObject)
               myTextObject.Text = "new field text goes here"
               mySection.SectionFormat.EnableSuppress = True
               ' Here is where I want to change the formula for the Suppression
            End if
            iloop = iloop + 1
    Next
Next
I can not find any reference to the actual suppression formula in the SDK help file.
Note, the EnableSuppress can be set to True for False, but if there is a formula for dynamic suppression, the True or False value is overwritten. The results of the formula determine the suppression.
Is there a way to reference this formula. I know that I can put on in using the Crystal Report Designer software, I need to modify this formula using VB code and the SDK.

Hello, Mark;
If you are using the ReportDocument object you do not have access to the Conditional Suppression formula. You can get around it by using a formula field in the report for the supression and then using the FormulaField code to change it at runtime.
If you want to change the supression condition directly at runtime you need to use RAS and the ReportClientDocument.
Elaine

How to access the photos on icloud

hi
how to access the photos which i saved in i cloud, from my iPhone 5,
Note: i do not use any PC. and i only have purchased 20 GB of space on an annual sub. so as to save my photos, and create space in my phone and now i am unable to access it,
please advise
thanks
xxv

There isn't really a way to "save" photos to iCloud currently with non-beta software.
iCloud is involved with photos in 2 ways -- backup and Photo Stream.
Backup of an iOS device includes Camera Roll photos but they cannot be viewed at iCloud.com -- the backup can only be used when doing a restore of an iOS device.
Photo Stream photos also cannot be viewed at iCloud.com; Photo Stream is designed as a method of transferring photos from one device to another and is not designed to store the photos. More info http://support.apple.com/kb/HT4486
There is a new feature -- "iCloud Photo Library" -- coming sometime after the iOS 8 release next week: http://www.macrumors.com/2014/09/12/apple-demotes-icloud-photo-library-beta/

I used a partitioned HDD for time machine, using a partition already containing other data files. I am now no longer able to view that partition in Finder. Disk Utility shows it in grey and "not mounted". Any suggestions of how to access the files?

I used a partitioned HDD for time machine, using a partition already containing other data files. I am now no longer able to view that partition in Finder. Disk Utility shows it in grey and "not mounted". Any suggestions of how to access the files? Does using time machine mean that that partition is no longer able to be used as it used to be?
HDD is a Toshiba 1TB, partitioned into two 500GB partitions.
OS X version 10.9.2

Yes, sharing a TM disk is a bad idea, and disks are cheap enough so that you don't need to.
Now
Have you tried to repair the disk yet

How to access the pendrive on my Airport Extreme via my iPhone 3GS?

Similar Messages

Maybe you are looking for