How to ACS 5.0.0.21 Expresss integrate with Active Directory Standar 2003 and authenticate PEAP MSCHAPV2
Hi:
My name is Ivan, I have a trouble
I have a ACS 5.0.0.21 express, and i have to integrate with Active Directory (AD) 2003 Standar. I should authenticate the users of the Domain in the LAN with PEAP MSCHPAV2, using the follow:
Cisco WLC 4402 + Cisco ACS 5.0.0.21 + Active Directory
I need to know if i should to install a certificate in the ACS 5.0.0.21 or some agent remote install in the AD.
I put in the ACS a external database with the AD, and i already select the users on the domain in the ACS Express.
Please could you tell me all the steps to autenticate the users on the Domain using the ACS Express and the Active Directory,
I would like to know wich are the configuration that i have to do in my ACS express to authenticate using PEAP MSCHAPV2
Regards
Ivan
See the below URL - multiple config guides on what you want to do:-
http://www.cisco.com/en/US/products/ps6366/prod_configuration_examples_list.html
HTH>
Similar Messages
-
ACS 5.3, EAP-TLS Machine Authentication with Active Directory
I have ACS 5.3. I am testing EAP-TLS Machine Authentication using Active Directory as an external Identity Store. II was testing and everything was going fine until I did some failure testing.
My problem: I deleted my computer account out of Active Directory and tried to authenticate my wireless laptop and it still worked when it should have failed.
Here is some of the output of the ACS log. You can see that the computer could not be found in AD and this was returned to the ACS. However, ACS still went ahead and authenticated the computer successfully.
Evaluating Identity Policy
15006 Matched Default Rule
22037 Authentication Passed
22023 Proceed to attribute retrieval
24433 Looking up machine/host in Active Directory - LAB-PC-PB.VITS.attcst.sbc.com
24437 Machine not found in Active Directory
22016 Identity sequence completed iterating the IDStores
Evaluating Group Mapping Policy
12506 EAP-TLS authentication succeeded
11503 Prepared EAP-Success
Evaluating Exception Authorization Policy
15042 No rule was matched
Evaluating Authorization Policy
15006 Matched Default Rule
15016 Selected Authorization Profile - Permit Access
22065 Max sessions policy passed
22064 New accounting session created in Session cache
11002 Returned RADIUS Access-Accept
I was assuming that if the computer was not found, the Identity Policy would fail, so I did not configure any authorization policy. Do I need an authorization policy to tell the ACS to fail the authentication if the machine cannot be found in AD? If I need an authorization policy, how do I configure it?
Note: In my Identity Store Sequence, I did enable the option:
For Attribute Retrieval only:
If internal user/host not found or disabled then exit sequence and treat as "User Not Found"
but this only seems to work for internal identity stores (at least based on my testing)
Under my Access Policy Identity tab, I configured the following Advanced features:
Advanced Options
If authentication failed
RejectDropContinue
If user not found
RejectDropContinue
If process failed
RejectDropContinue
And that didn't do anything either.
Any ideas? Thanks in advance.Can try the following. Define an attribute to be retrieved from Active Directory and that exists for all objects. When defining the attribute it can be given a default value. Assign a default value which is a value that will never be returned for a real machine entry (eg "DEFAULTVALUE") and give it a "Policy Condition Name"
Then can make a rule in the authorization policy such as
If "Policy Condition Name" equals "DEFAULTVALUE" then "DenyAccess" -
ACS 4.2.0.124 Appliance with Active Directory with windows 2008
we have a solutions of 802.1x with Cisco ACS appliance wich is working fine, the soluction include two ACS appliance version 4.2.0.124, 02 remote Agent wich is setting up on windows 2003. The remote agent is integrated with Active Directory windows 2003. The computers have windows XP with service pack 2 and service pack 3, all computers do machine authentication and then user authentication. My customer in thinking in migrate the Active Directory windows 2003 to windows 2008. My question is ¿there wil be some problem with Active Directory 2008 with the current soluctión of ACS and 802.1x solution ? or I will have to do aditional task.
MarcoHi,
You can find the suported Windows Server versions on the online documentation:
ACS 4.2: http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/windows/install.html#wp1041376.
ACS 4.2.1: http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2.1/Installation_Guide/windows/install.html#wp1041376.
So, i would suggest you to double-check carefuly the Release and Service Pack of the new 2008 Servers and also the OS bit version to make sure you migrate to Win2008 but continue on a supported scenario.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
ACS Local databse authentication as a failover to Active Directory
Hi all
Router- 10.10.10.1
ACS-10.10.10.2
AD-10.10.10.3
in AD - created a group called "telnet users" - added user with name of - john
I have added cisco router as clients in Cisco ACS 5.1 and integrated with Active directory. when i telnet to 10.10.10.1 , i can logon with Active directory account
but i want a faiover to active directory with ACS local database
Can you let me know how to configure?
In ACS - i have created a user with name of - Test1 and Identity group : all groups.
Can any one help please.Hi,
You need to create an Identity Store Sequence and then select that Identity Store under the Identity section of the Access Service.
1.
2.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
Autheticating useing Cisco ACS 4.2 integrated with Active Directory 2003
How do i check that users are Autheticated useing Cisco ACS 4.2 integrated with Active Directory 2003, any one help me in this thanks
You can't actually see the user's membership from ACS. All you can do, create group-mapping under external database >> group mapping section. This would give you an option to map external (AD) group with an Internal group.The group memberrship need to be modified under Active Directory.
Once user is succussfully authenticated and learned as a dynamic user in ACS user setup database, it would be mapped with an ACS internal group based on group mapping we did.
Let me know if you have any doubts.
Regards,
Jatin -
How do I use Automator to duplicate a folder with graphics on my desktop and erase their Resource forks?
I do not use command line and tried to use ZapResourceForksAMAub_1.2 which I downloadedand instaled the Zap Resource Forks.action. Next I tried to use their sample copy-zap-rsrc.workflow in Snow Leopardon my Mac Pro. The 3 different steps are displayed in Automator but there is no place to put in which folder (on my deskto) to copy, and remove the resource forks from the graphic files.
Can sombody please step me through this please please.
W.W.Unfortunately, Back to My Mac only works across computers using the same iCloud account.
-
How many different computers can I sync my iPod with? My laptop crashed and was completely wiped clean and this was the machine that my iPod synced with so I don't know if it will be counted as a "new" computer when I sync my iPod.
You can sync with onee at a time. Syncing to another will erase the current content.
Copy everything from your backup copy of your old computer to your new one. -
How do I get IE to read pdf's with a Windows 7 OS and acrobat 7 on my system?
How do I get IE to read pdf's with a Windows 7 OS and acrobat 7 on my system? It works with firefox. It worked previously but I think the automatic upgrade to reader 9.4 messed it up - so how do I fix it?
Hi,
It looks like the default association of your PDFs was set to Adobe Acrobat, when you installed Adobe Reader 9.4.0. I would request you to either uninstall Adobe Reader 9.4.0 and install it again. This time around, you will receive a window asking you to chose between Adobe Acrobat 7 and Adobe Reader 9.4.0 as the default PDF viewing application, make sure you select Adobe Reader 9.4.0 and continue on. This will associate Adobe Reader 9.4.0 as the default PDF viewing application and your internet explorer will be able to open PDFs without an issue.
If an uninstall seems out of the question, you can change the following registries to point to the path of AcroRd32.exe (i.e. the path wherein you have installed Adobe Reader 9.4.0. By default it would be something like: C:\Program Files\Adobe\Reader 9.0\Reader\AcroRd32.exe). The quotes mentioned below are intentional and must be included.
i. HKEY_CLASSES_ROOT\Software\Adobe\Acrobat\Exe\(Default) - Change the value to "C:\Program Files\Adobe\Reader 9.0\Reader\AcroRd32.exe"
ii. HKEY_CLASSES_ROOT\AcroExch.Document.7\shell\Open\command\(Default) - Change the value to "C:\Program Files\Adobe\Reader 9.0\Reader\AcroRd32.exe""%1"
iii. HKEY_CLASSES_ROOT\AcroExch.Document.7\shell\Read\command\(Default) - Change the value to "C:\Program Files\Adobe\Reader 9.0\Reader\AcroRd32.exe""%1"
This should set the default application to view PDFs as Adobe Reader 9.4.0 and let you view PDFs in browser as well.
Hope this works.
Ankit -
How to get Primary Group details of a user from Active Directory
Hi ,
This is Viswanath. I want to know how can we retrieve the primary group of a user (Active Directory). I have searhed the entire forum but could not get the required information.
The reference link is which i have searched is : http://forum.java.sun.com/thread.jspa?threadID=581444
I got a sample .NET project where we can retrieve the primary group information :
refer to the link : http://dunnry.com/blog/DeterminingYourPrimaryGroupInActiveDirectoryUsingNET.aspx
you can download the sample project and build that in VS.NET 2003 and see the result. Please let me know if this kind of implementation is possible in java.
Kindly help me as i have to provide a solution to my client.
Regards,
Viswanath.
Edited by: sriganesh on Jun 22, 2008 10:36 AM
can anybody please share their thoughts on the aboveTo connect to the Active Directory you can do something like this:
import java.util.Hashtable;
import javax.naming.Context;
import javax.naming.NamingException;
import javax.naming.directory.DirContext;
import javax.naming.directory.InitialDirContext;
public class AD
public static void main(String[] args)
Hashtable environment = new Hashtable();
//Just change your user here
String myUser = "myUser";
//Just change your user password here
String myPassword = "myUser";
//Just change your domain name here
String myDomain = "myDomain";
//Host name or IP
String myActiveDirectoryServer = "192.168.0.20";
environment.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.ldap.LdapCtxFactory");
environment.put(Context.PROVIDER_URL, "ldap://" + myActiveDirectoryServer + ":389");
environment.put(Context.SECURITY_AUTHENTICATION, "simple");
environment.put(Context.SECURITY_PRINCIPAL, "CN=" + myUser + ",CN=Users,DC=" + myDomain + ",DC=COM");
environment.put(Context.SECURITY_CREDENTIALS, myPassword);
try
DirContext context = new InitialDirContext(environment);
System.out.println("Exit!!");
catch (NamingException e)
e.printStackTrace();
Reddy Pathepuram
Inteligic Inc -
Cisco ACS 4.2 integration with Active Directory
Hello,
I´m new in the administration of ACS, we have recently implemented on server ACS version 4.2
for manager all users authorization for our Network.
We are in one environement which have an Active Directory, group and users.
Now, i´m just able to creat a new user in ACS and work with on the Client SWITCH, what i need to do, is to integrate my ACS 4.2 with Active Directory.
for work with the user and Group that a register in my AD.
Someon can help me please?You can't actually see the user's membership from ACS. All you can do, create group-mapping under external database >> group mapping section. This would give you an option to map external (AD) group with an Internal group.The group memberrship need to be modified under Active Directory.
Once user is succussfully authenticated and learned as a dynamic user in ACS user setup database, it would be mapped with an ACS internal group based on group mapping we did.
Let me know if you have any doubts.
Regards,
Jatin -
How to install Small Business Server 2008 in an existing Active Directory domain
It is shown on this page:
http://support.microsoft.com/kb/884453, "How to install Small Business Server 2003 in an existing Active Directory domain".
Is it possible to do this with SBS2008 ?
If "YES", are there any published information about the procedure ?Yes, it is. Thank you very much.
But there is something that confuses me - I want to migrate from Win2003Std to SBS2008. And also, I want to keep the existing Win2003Std as a second DC for a long time.
But it is written in the shown article:
... After the migration is finished, you must remove the Source Server from the network within 21 days. ...
Is this rule mandatory for the scenarios where the Source Server is Std, not SBS ? As I know, I can have more than one DC(Win2003Std/Win2008Std) together with SBS2003. But what about SBS2008 ? -
ACS Express integration with Active Directory
Hello,
I have ACS Express version 5.0.1 installed on Cisco ADE; I'm trying to get it integreated with an Active Directory without sucess.
I did packet captures on the ASA that is in between and I can see communication going thru just fine. I ran a diagnostic on the ACS express and got this:
DIAGNOSTIC USING THE IP ADDRESS OF THE DOMAIN CONTROLLER:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Tabla normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Output of AD Domain Diagnostics:
IP Diagnostics
Local host name: he-zfm-acs-01
Local IP Address: 172.31.67.10
Not found in DNS!Make sure it is in Reverse Lookup Zone.
FQDN host name:he-zfm-acs-01.clarocr.americamovil.ca1
Domain Diagnostics:
Domain: 172.24.2.93
Subnet site:
WARNING! Unable to locate computer's subnet site in Active Directory.
Ask your Active Directory administrator to add this computer's subnet
to the appropriate site.
DNS query for: _ldap._tcp.172.24.2.93
Found no SRV records!
Computer Account Diagnostics
Not joined to any domain
AD Agent Process Status: Not joined to any domain
DIAGNOSTIC USING THE AD REALM:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Tabla normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Output of AD Domain Diagnostics:
IP Diagnostics
Local host name: he-zfm-acs-01
Local IP Address: 172.31.67.10
FQDN host name:he-zfm-acs-02.clarocr.americamovil.ca1
Domain Diagnostics:
Domain: CLAROCR.AMERICAMOVIL.CA1
Subnet site: TELECOM
DNS query for: _ldap._tcp.CLAROCR.AMERICAMOVIL.CA1
Found SRV records:
rom-pro-dc-03.clarocr.americamovil.ca1:389
Testing Active Directory connectivity:
Domain Controller: rom-pro-dc-03.clarocr.americamovil.ca1
ldap: 389/tcp - good
ldap: 389/udp - good
smb: 445/tcp - good
kdc: 88/tcp - good
kpasswd: 464/tcp - good
ntp: 123/udp - good
Domain Controller: rom-pro-dc-03.clarocr.americamovil.ca1:389
Domain controller type: Windows 2003
Domain Name: CLAROCR.AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Forest Name: AMERICAMOVIL.CA1
DNS query for: _gc._tcp.AMERICAMOVIL.CA1
Testing Active Directory connectivity:
Global Catalog: rom-des-dc-01.desa1sv.americamovil.ca1
gc: 3268/tcp - timeout
No TCP LDAP response, giving up on rom-des-dc-01.desa1sv.americamovil.ca1
Global Catalog: rom-amv-dc-02.americamovil.ca1
gc: 3268/tcp - good
Global Catalog: rom-tlc-dc-01.telecom.americamovil.ca1
gc: 3268/tcp - good
Global Catalog: rom-pro-dc-03.clarocr.americamovil.ca1
gc: 3268/tcp - good
Global Catalog: rom-tlc-dc-02.telecom.americamovil.ca1
gc: 3268/tcp - good
Global Catalog: rom-amv-dc-01.americamovil.ca1
gc: 3268/tcp - good
Domain Controller: rom-amv-dc-02.americamovil.ca1:3268
Domain controller type: Windows 2003
Domain Name: AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Domain Controller: rom-tlc-dc-01.telecom.americamovil.ca1:3268
Domain controller type: Windows 2003
Domain Name: TELECOM.AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Domain Controller: rom-pro-dc-03.clarocr.americamovil.ca1:3268
Domain controller type: Windows 2003
Domain Name: CLAROCR.AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Domain Controller: rom-tlc-dc-02.telecom.americamovil.ca1:3268
Domain controller type: Windows 2003
Domain Name: TELECOM.AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Domain Controller: rom-amv-dc-01.americamovil.ca1:3268
Domain controller type: Windows 2003
Domain Name: AMERICAMOVIL.CA1
isGlobalCatalogReady: TRUE
domainFunctionality:
forestFunctionality: 0 = (DS_BEHAVIOR_WIN2000)
domainControllerFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Forest Name: AMERICAMOVIL.CA1
Computer Account Diagnostics
Not joined to any domain
AD Agent Process Status: Not joined to any domainDennis,
TIme in sync on the ACS and AD servers?
Faisal -
ACS 4.2 with Active Directory
i have a windows 2003 active directory domain setup with cisco acs 4.2 also installed on it I'm using a 2611xm router(ios 12.4 advsec) if I create users on the acs, i have no issues setting up AAA Authentication however, I have followed the online documentation, to set the ACS to use my windows user database(AD)...but when i try to log in, the authentication fails. On my domain, I have created a computer account named 'CISCO' and I have granted my user "Dial-in" permission. When I checked the failed attempts report on the ACS server it said, "authen failed" and under the authentication code, it said "internal error
Here are some results from some debug commands. Any help would be greatly appreciated
SDMRouter#
*Mar 1 00:24:44.365: AAA/BIND(00000007): Bind i/f
*Mar 1 00:24:44.369: AAA/AUTHEN/LOGIN (00000007): Pick method list 'MY_OWN'
*Mar 1 00:24:44.373: TPLUS: Queuing AAA Authentication request 7 for processing
*Mar 1 00:24:44.377: TPLUS: processing authentication start request id 7
*Mar 1 00:24:44.377: TPLUS: Authentication start packet created for 7()
*Mar 1 00:24:44.381: TPLUS: Using server 10.1.1.3
*Mar 1 00:24:44.385: TPLUS(00000007)/0/NB_WAIT/855EB078: Started 5 sec timeout
*Mar 1 00:24:44.393: TPLUS(00000007)/0/NB_WAIT: socket event 2
*Mar 1 00:24:44.393: TPLUS(00000007)/0/NB_WAIT: wrote entire 33 bytes request
*Mar 1 00:24:44.393: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:44.397: TPLUS(00000007)/0/READ: Would block while reading
*Mar 1 00:24:44.401: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:44.401: TPLUS(00000007)/0/READ: read entire 12 header bytes (expec
t 16 bytes data)
*Mar 1 00:24:44.405: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:44.405: TPLUS(00000007)/0/READ: read entire 28 bytes response
*Mar 1 00:24:44.405: TPLUS(00000007)/0/855EB078: Processing the reply packet
*Mar 1 00:24:44.405: TPLUS: Received authen response status GET_USER (7)
*Mar 1 00:24:48.900: TPLUS: Queuing AAA Authentication request 7 for processing
*Mar 1 00:24:48.904: TPLUS: processing authentication continue request id 7
*Mar 1 00:24:48.904: TPLUS: Authentication continue packet generated for 7
*Mar 1 00:24:48.908: TPLUS(00000007)/0/WRITE/84D88908: Started 5 sec timeout
*Mar 1 00:24:48.908: TPLUS(00000007)/0/WRITE: wrote entire 25 bytes request
*Mar 1 00:24:48.936: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:48.936: TPLUS(00000007)/0/READ: read entire 12 header bytes (expec
t 16 bytes data)
*Mar 1 00:24:48.936: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:48.936: TPLUS(00000007)/0/READ: read entire 28 bytes response
*Mar 1 00:24:48.940: TPLUS(00000007)/0/84D88908: Processing the reply packet
*Mar 1 00:24:48.940: TPLUS: Received authen response status GET_PASSWORD (8)
*Mar 1 00:24:51.981: TPLUS: Queuing AAA Authentication request 7 for processing
*Mar 1 00:24:51.985: TPLUS: processing authentication continue request id 7
*Mar 1 00:24:51.985: TPLUS: Authentication continue packet generated for 7
*Mar 1 00:24:51.989: TPLUS(00000007)/0/WRITE/84D88908: Started 5 sec timeout
*Mar 1 00:24:51.989: TPLUS(00000007)/0/WRITE: wrote entire 24 bytes request
*Mar 1 00:24:52.150: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:52.154: TPLUS(00000007)/0/READ: read entire 12 header bytes (expec
t 6 bytes data)
*Mar 1 00:24:52.154: TPLUS(00000007)/0/READ: socket event 1
*Mar 1 00:24:52.154: TPLUS(00000007)/0/READ: read entire 18 bytes response
*Mar 1 00:24:52.154: TPLUS(00000007)/0/84D88908: Processing the reply packet
*Mar 1 00:24:52.154: TPLUS: Received authen response status FAIL (3)Most likely a permission issue, please see this link,
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.1/installation/guide/windows/postin.html
Regards,
~JG
Do rate helpful posts -
My photo stream has always synced just fine between my Windows 7 PC and my iPhone 5. However, just a month or so ago it stopped automatically syncing. I turned it off and on in the iPhone settings in two places, deleted all the photos manually, signed out of iCloud on my PC and even uninstalled iCloud on my PC. Now it appears to be partially working. If I add or delete photos from my Photo Stream on my iPhone, the changes are reflected on my PC. However, if I delete photos or add photos to my Photo Stream folder on my PC, the changes are not reflected on my iPhone. I can delete all the pictures out from my Photo Stream on my PC but they are all still there in my Photo Stream on my iPhone. How do I get the two devices to sync properly again?
Hello snoopy016,
Thank you for using Apple Support Communities.
For more information, take a look at:
iCloud: My Photo Stream troubleshooting
http://support.apple.com/kb/ts3989
I added some photos into My Photo Stream on my Windows PC, but they don't appear in My Photo Stream on any of my devices.
Have a nice day,
Mario -
How to make a thumbnail to triger a lightbox with a several images inside and navigation option
hy
ive tryd the the tooltip but it wont let me to navigate in the lightbox
any idea?Use the techniques outlined by Adobe's Terry White in the following video: How To Design a Mega Custom Menu in Adobe Muse CC - YouTube
If you're still running into issues, can you please describe what you're trying to achieve in a bit more detail? Do you have a site that achieve's this effect/photos/more detailed description? Thanks.
Best of luck and hope that's helpful
Maybe you are looking for
-
G5 OS 10.4 and G3 OS 8.6 to wireless router?
My main internet machine is my G5, but I also connect quite frequently with my G3 which runs various legacy OS 8.6 software. For ease of use, I'd like to connect them both to a wireless router, but never having owned one before I'm unsure on a couple
-
FF 4.0. The menus flash like a key is being held down making them inaccessible. The problem persists with all plugin's turned off. Firefox box in top left corner not showing. The old FF logo show there instead.
-
I am trying to apply a BPEL orchestration (11g PS2) to receive and process an outbound msg from Salesforce. Salesforce provides the wsdl for the outbound msg that Salesforce sends to my service. Alone, this is not a problem. However, circumstances re
-
Hi, I have 3 KPI's, I want all the KPI's in Column wise. By default it is row wise but for my requirements is. I want to make all KPI's as a coulm. Can anyone tell me. Its annoying me like anything. Thanks & Regards Pomani Sankaran
-
Setting screen resolution on a retina MacBook Pro
If I need my screen resolution to be 1920x1080, how do I set that in System Preferences>Displays? Thanks very much.