How to activate camera attributes in the MAX / LabVIEW

Hello,
I have created an icd file for a VieWorks camera. Therefore I used the camera file generator tool of NI. In this tool I can setup camera attributes. After creating the file, I opened the MAX and selected the camera in the IMAQ devices. The attributes I generated where correctly shown. The question now is how to activate the attributes. For instance I created an attribute to activate / deactivate the FAN. When I select the attribute in the MAX and set the value to ON, nothing happens.
This also fails when I use the SetCameraAttributes.vi in labview. I use LV2009 and IMAQ 4.6.1
Does anyone have any suggestions?
Regards,
Marc Vanmaris

Hello,
Just check in MAX that the "Serial Enable" is selected. It seems that the serial command is not send to your camera.
Hope this helps

Similar Messages

Missing camera attributes with the NI IMAQ for IEEE-1394 driver

I'm using an ORCA-AG and the IEEE-1394 driver. When i look at the camera attributes (either with MAX or the attribtue inquiry vi.) i can see just some of them (brightness, shutter,...). I have tried the ORCA-ER, which has the same attributes, but uses the PCI-1424 framegrabber. Using this camera i can see and modify more attributes (light mode,...). How can i modify them with the IEEE 1394 driver?
I also have another problem. When i use 1x1 binning the image must be 8bits, if is use 16bits, max cannot aquire the image (timeout error). Does anyone have the same problem?
Thank you very much.

Some non-standard attributes can be modified by directly reading and writing to the memory of the camera. Your camera manual probably has memory locations listed for the different attributes. You can get to these using the low level firewire routines. I have done it once or twice.
Bruce
Bruce Ammons
Ammons Engineering

Setting camera attributes with the PCI-1405

I have the PCI-1405 Imaq card. I was wondering how I set camera attributes like gain and exposure time. Every time I try to use the set camera attribute VI I get an error message saying the attribute is not valid.

khsay--
      Installing the driver will allow the framegrabber (1405) to communicate with the computer. I want to verify that you are using Measurement and Automation Explorer (MAX) to test the sanp/grab features of your camera. This will allow you to directly interact with the hardware.
If you are, and this is where you are getting the extract image error. First double-check that you know what kind of communication standard the camera uses (for instance, CCIR or RS170) and make sure that this is selected in MAX.
      The camera might not be using a known standard, in which case you will need a camera file that tells the computer and framegrabber how to interpret the camera's information and signal. You can look in MAX and see if the camera is listed, if it is the camera file is If not, you can try going to www.ni.com/camera and see if you can get a camera file there. If not you will need to try contacting the manufacturer to see if they have one, and if not you will need to create one using the camera file generator from the ni.com/camera.
     Just let us know if this information helped to solve the issue and if not reply back so that we can help. Also, in the future if you have a new issue you might consider posting in a new thread.
Regards,
John H.
Applications Engineer
National Instruments

How to activate camera option in message in ios 5

how to activate camera option in message in ios 5

The MMS setting appears because of the carrier file installed on your phone, assuming your carrier supports MMS, which you say your carrier does. First try restting your phone:
Press the sleep/wake button & home button at the same time, keep pressing until you see the Apple logo, then releae.
If no change, restore your phone from backup. Follow this by syncing your iTunes content back to your phone.

HT4865 How to activate my phone with the apple id

how to activate my phone without the apple id

I know it's the right apple i.d. and the password is right because I can get into icloud on the computer.

Is there a way to reset Lightroom back to when I first started the trial. In other words how it first came "out of the box"?

Is there a way to reset Lightroom back to when I first started the trial. In other words how it first came "out of the box"?
I read some tutorials and I would like to start fresh.

Not sure what your goal is here, but there are a couple of things you can do.
In preferences>General - Reset all warning dialogs.
In Preferences>Presets - Reset all default develop settings.
Finally, if you really want to start fresh with all your photos, go to File>New Catalog. Note: the new catalog will not have any photos in it. You will have to re-import all your photos.
If you are still on the 30 day trial and you are hoping to start over with a new 30 day trial, the answer is No!

How to include Navigational attribute in the selection screen

Hello All,
Can any body please tell me how to include a navigational attribute in the selection screen in BEX?

Let´s go step by step.
In your example, you mentioned the characteristic called 0MAT_PLANT. Its navegational attributes are allocated in the same dimension the main characteristic belongs. So 0MRP_CONTRL, as a navegational attr. must be allocated in the same dimension as 0MAT_PLANT.
1) In query designer in Bex (left pane) find the dimension where 0MAT_PLANT is allocated. Find the navegational attr. in the same dimension, 0MRP_CONTRL. Pls verify you are looking to a navegational attribute, activate technical names and the name of the attr must be 0MAT_PLANT__0MRP_CONTRL.
2) Below the attribut (still left pane) you will find a Variable icon (yellow). If you see the "+" symbol, it means that at least one variable exists (standar or not). Open it and check if the variable suits your requeriment to set it in selection screen. If not, create a new one (let me know if you need help with this task).
3) Once you have your variable for the navegational attribute, drag and drop it to the design area (row, column, filter).
4) Verify the order you want this variable to appear from the menu bar: Query properties -> Sequence of Entry Variables.
Hope this helps. Leticia
Edited by: Leticia Laura Locatelli on Oct 1, 2008 10:41 PM

How to add Custom Attributes in the SOAP header for OWSM

Hi,
I like to know how to add the Custom Attributes in the SOAP header for OSWM username token authentication.
Currently we are getting the header element like
<wsse:Security xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd" xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">
here we need to add the attribute "soap:mustUnderstand="1" , so the element will look like
<wsse:Security soap:mustUnderstand="1" xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd" xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">
Any info on this will be helpful.
Thanks,
ArunM

Hi Jay, you can make it in more than 1 way.
I suggest you the following:
- create an URL iview that points to any URL you want.
- define a Resource that points to the iview (with a window name, to open in new window)
- define an Area that points to the resource
- add your new Area to the your current Area Group
Regards!

PR05 - How to activate a Function in the Object Services Toolbox

Hi,
How do I activate a function in the Object Services Toolbox?
In transaction PR05 (Travel Expense Manager) select any trip and then click on 'Change'. This takes you to the screen for the individual trip.
On the top left of the screen is the 'Object Services Toolbox'.
If I drop down on this list then select 'Create' there are 5 options under 'Create' i.e. 'Create attachment', Create Note', 'Create External Document', 'Store Bus. Doc', and 'Enter Bar Code'.
The 'Enter Bar Code' is deactivated. I would like to know how to activate this.
Thank you.
Warren.

no idea

How to activate a function in the Object Services Toolbox of PR05

Hi,
In transaction PR05 (Travel Expense Manager) select any trip and then click on 'Change'. This takes you to the screen for the individual trip.
On the top left of the screen is the 'Object Services Toolbox'.
If I drop down on this list then select 'Create' there are 5 options under 'Create' i.e. 'Create attachment', Create Note', 'Create External Document', 'Store Bus. Doc', and 'Enter Bar Code'.
The 'Enter Bar Code' is deactivated. I would like to know how to activate this.
Thank you.
Warren.

I think you need to check for IMG transaction code OAC5 & OAC3 and also check IMG configuration setting under
Application server-->basis services > Archive Link> customizing incoming documents--> bar code scenarios
a®

How to chane camera attributes

Hello all, I need to modify i real time some camera attributes ( Exposure time, Gain, etc.) but with the function IMAQdxSetAttribute is it not possible, and cause an error, (attributes like zoom, focus, I don`t have any problem).
It is possible to change this attributes with other function ???
thanks for all.

http://digital.ni.com/public.nsf/allkb/E50864BB41B54D1E8625730100535E88

BC: How to set an attribute in the validateEntity method

Hi All,
a little question that hopefully someone knows the answers to.
We override the validateEntity() method in our Entity Objects to perform validation. During our validation based on the value of a (bound to a database column) attribute, we conclude that another attribute (bound to another database column) needs to be set to a specific value.
For example: we have a table with columns A and B. The user can edit both, but when the value of column A is set to 'value1' the value of column B is set to '0' in the validateEntity() method. (When the value of column A is something different the user may fill anything in column B).
Because all our validation and logic is centralised in the validateEntity() method we would also like to have this logic in there.
However we face some problems:
If we use setAttribute() or setAttributeInternal() the validation is run again (and again, and again, eg a loop). I can get out of the loop, but i really don't want the validation to be done again.
So i looked up the documentation on oracle.jbo.server.EntityImpl and i specifies that i should use populateAttributeAsChanged().
I have tried that, but now the user gets to see 'JBO-25014: Another user has changed the row...'. The same result with populateAttribute().
I tried to change the attribute to refresh after insert/update, but that doesn't help.
Can anybody help?
Thanks in advance.
Regards,
Robert

What if I wanted to "reset" one attribute when validation fails, I can do this but I don't see the error message.
my method looks like this:
public boolean validateDatumEffectueringAlsStatusIsDrie() {
if (new Number(3).equals(getStatus()) &&
getDatumEffectuering() == null) {
setStatus((Number)getPostedAttribute(STATUS));
return false;
return true;
This probably fires the method twice when status was set to 3, and the second time it does not fail because status is set back to the value that was not 3, so I don't see the error message that was shown the first time.
So how is this done properly?
The reason I do this is because DatumEffectuering is readonly when status is 3 so when the page refreshes after the validation the empty date field is readonly.... I need the status to be reset after validation of the entity fails.
Thanks in advance!

How to create own attributes in the graph.xml of 10g Reports

Hi,
Iam using 10g reports. Iam recreating the graphs in 10g which were created in Graphics builder earlier. While doing that I found lot of features are missing in 10g reports charts wizard. It has only limited number of Graph types when compared to the Graphics builder. Like there is no Curve graph in 10g. The available are Line, Bar and Area. So how can I draw a curve instead of line? 10g Legend looks very ugly. There is lot of space between the values. Is there anyway that I can add my own attributes in the graph.xml and register in the reports?
Please advise.
Thanks.
Ram Dontineni.

Hi Ram,
how can I draw a curve instead of line?I have posted a Q in BI Beans Forum for you, we should get an answer there:
Curved Line Graph?
10g reports charts wizard. It has only limited number of Graph types when compared to the Graphics builderThat may not be exactly true.
10g Graph Wizard supports 11 major graph types, and 47 sub-types
While 6i Graphics Builder supported 5 major graph types and 35 graph sub-types
There are differences between 6i Graphics and 10g Graph Wizard, so certain things you might have been able to do in 6i may not be entirely possible in 10g. However, the main advantages of the 10g Graph option are - it internally uses BI Beans, which is used in ALL Oracle poducts like JDeveloper, Discoverer, Oracle Apps etc. So the customer gets a consistent look-and-feel. And that it is possible to define your Graph in XML format (and through Java API in JDeveloper).
We have published a list of FAQ's on OTN where you should get answers to at least some of your Q's:
http://otn.oracle.com/products/reports/index.html (click on Graphing FAQ)
Is there anyway that I can add my own attributes in the graph.xml and register in the reports?This will not be possible, however, you should take a look at the complete list of elements and their attributes that is exposed in Graph.dtd - you can then choose the attributes you want, and add them to your Report's Graph.xml:
http://otn.oracle.com/products/reports/htdocs/getstart/whitepapers/graphdtd/graph_dtd_technote_2.html
Navneet.

HOW TO ACTIVATE PERSONALIZE OPTION IN THE MASTHEAD

Hi , i am hanif i am new to the portal.Please can anyone tell me how to activate the personalize option on the masthead.

Hi Hanif,
EU Role contains Portal Personalization (workset). See below.
http://help.sap.com/saphelp_nw04s/helpdata/en/46/a1be96f7bf407db6ac78e343b8cef1/frameset.htm
What you can do is to assign this EU Role to one of the existing Groups/Roles that you have created as a standard for ALL your Portal users. Once you have assign the EU Role to this standard "End User"role you have created, all your Portal users will see the option for personalize on the top right of Portal.
Assigning Roles to Users and Groups
http://help.sap.com/saphelp_nw04/helpdata/en/ed/845890b89711d5993900508b6b8b11/frameset.htm
Hope that helps and award points for useful suggestions.
Ray

How to Update Extended Attributes For the Users in SRM Organization?

Hi,
I am using 'BBP_UPDATE_ATTRIBUTES' function module to load the Default Attributes for the users in a custom program. I am able to update many attributes like company code, Movement type, catalog id, material usage, shop on behalf of and address ship to. But I am having problem updating extended attributes Plants(Attribute ID 'WRK') and Storage Locations (Attribute ID 'LAG').
Storage location and Plants has many values. Can anyone have experienced this problem before. I appreciate any help I get. I debugged enough and not able to find any other function module to do this.
Thanks and Regards,
Sreeni..

Hi Sreeni,
I'm stuck up in the same problem. Did you get any solution for this? If yes please provide the same.
Regards,
Gajendra
Message was edited by: Gajendra Bhatt

How to activate camera attributes in the MAX / LabVIEW

Similar Messages

Maybe you are looking for