How to add wireless to a MacPro?

I have a 2008 MacPro and an airport in another part of the house. How do I reliably add a wireless reciever to the MacPro? I have PCIe slots, USB, or Firewire, and would appreciate a specific recommendation with a tested solution. I am currently running 10.7 OS.
Thanks!

You don't really add or delete them.. the airport Extreme does not generally have controls except for times access.
Is that what you intend to use?? Please just look up timed access.. that will allow you to prevent a computer or device accessing the router at particular times..

Similar Messages

How to add an extra DVD drive to a MacPro?

How to add an extra DVD drive to a MacPro?
Is there any where instruction on the procedure?

There are instruction in the manual that came with the computer. Set the drive jumper to CS (Cable Select). You will need to remove the tray's lip.
<http://eshop.macsales.com/tech_center/index.cfm?page=removedrivedoor.html>
Be careful not to pinch or cut the cables when reinstalling the drive carrier.

How to add ipad 2 to wireless

how to add Ipad 2 to my wireless?

For anyone struggling with the collusal failure of iOS6. Do this > Settings > Safari > Clear cookies and Data. Then go to Wifi - Forget the network. Then turn off the iPad, turn it back on. Reconnect the wifi. You should get a 'success' message. Dear Apple, you really screwed this one up.

How to add hp printer in windows xp which is in a wireless network?

how to add hp printer in windows xp which is in a wireless network?

What printer?
In general, you can download and install the latest software for your printer from the "Support & Drivers" link at the top of this page.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

How to add a wireless printer to airprint?

How to add a wireless printer to airprint?

Only the printer manufacturers can add AirPrint support to their printers via firmware updates. If your printer isn't listed on this page as supporting AirPrint, then does the manufacturer have their own app in the app store that supports it ? If not then there are third-party printer apps such a PrintCentral Pro and Print n Share which might work with it.

How do I add wireless printer or Direct tv

How do I add wireless printer or Direct tv

These devices would be added the same way that any other wireless device is added as a client to a network......
1) Scan to select the network
2) Enter the wireless network password
Keep in mind that DirecTV cannot connect to a wireless network if there are special characters.....like an apostrophe, asterisk, dollar sign, etc......in the wireless network name.
So if your wireless network is named something like Ernestomelia's Wireless Network, DirecTV will not be able to to connect. Instead, the network should read something like ernestomelia network. A shorter name with no spaces would be better.
Your printer might have similar requirements, but you did not provide the make or model number of the device....so we don't have much to go on here. In general, you would want to contact support at the printer manufacturer for more specific information.

How to add a class in a project?

Hello!
i'm a beginner in developing and i don't know how to add a class in a project in Sun Java Wireless toolkit 2.5.2...
The name of my project is essai2 and i already put a class, LogoMIDlet and now i want to put my new class ComBasique, how can i do that?
and do you know if there is a program for bluetooth in order to connect my Nokia 6680 to another device that have a bluetooth?
thanks a lot for your answer!
Sophie

how to change the class name after the project is created.In NetBeans, right click the class name either in the declaration or constructor, select Refactor --> Rename... and follow the dialog.
You can refactor --> rename anything that is not in a guarded block. For those, there are options via the properties window.
db

Is my system DV7t-3300, or DV7t Quad Edition? And how to add more memory to it?

Dear forum,
I have an old notebook computer bought back in March 2010. It's a DV7t series. As it's getting slowly, I'm thinking of adding more memory. However, I'm not sure how much memory the motherboard can support for the upgrade.
I'm stuck with the first step, which is to decide the model number (and then motherboard) of it.
My original order email states the following:
YOUR CUSTOMIZED HP PC
dv7t quad edition
• Genuine Windows 7 Home Premium 64-bit
• Intel(R) Core(TM) i7-720QM Quad Core processor (1.6GHz, 6MB L3 Cache) with Turbo Boost up to 2.8 GHz
• FREE Upgrade to 4GB DDR3 System Memory (2 Dimm) from 3GB DDR3 System Memory (2 Dimm)
• 500GB 7200RPM SATA Hard Drive with HP ProtectSmart Hard Drive Protection
• 1GB Nvidia GeForce GT 320M - For i7-720QM and i7-820QM Processors
• 17.3" diagonal HD+ High-Definition HP LED BrightView Widescreen Display (1600 x 900)
• LightScribe SuperMulti 8X DVD+/-RW with Double Layer Support
• Webcam Only
• Intel Wireless-N Card with Bluetooth
• HP Integrated HDTV Hybrid Tuner
• HP Color Matching Keyboard
• 8 Cell Lithium Ion Battery
• No Modem
• Microsoft(R) Works 9.0
• HP Home & Home Office Store in-box envelope
However, the bottom of the notebook computer has a label that specifies the following:
Pavillion dv7
Serial: omitted
Product: WH764AV
Model: Q dv7t-3300.
I visited some memory buying website like 'crucial.com'. However, I was prompted to select the model and there were both dv7t-3300 CTO and dv7t Quad Edition. Unfortunately, they resulted in different kinds of memory (although the specs of the sugested memory modules seem to be the same, these two memory modules have different model numbers).
So, what model number my system has? 3300 CTO or Quad Edition?
Perhaps a suitable model number would tell me which motherboard this notebook has. Additionally, can anyone advice me about on how much memory my notebook can support (8GB or 16GB) maximum?
Thanks a lot!
Cruiser

Hi,
Max is 8Gb using the following manual:
http://h10032.www1.hp.com/ctg/Manual/c01859666.pdf
And from the following site:
https://www.ramcity.com.au/upgrade/hp-compaq/pavilion-dv7-series-notebook/dv7t-3300-cto/73893
The above manual shows you how to add/replace RAM. Looks like you have to buy 2 x 4Gb sticks.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

How to add Mac27" to existing home network? and read files on other PC computers (Window7)

How to add Mac27" to existing home network? and read files on other PC computers (Window7).
type of connection:
All computer (PC & Mac) connect to router (ethernet or wireless), then connect to internet.
condition:
internet works fine on all computer (PC & Mac).
existing 4 PC communicate well (share files & printers),
my problem:
can NOT add Mac into existing home network.
I tried SYSTEM PREFERENCES, then NETWORK, then ......... several times
could not make it work.
pleas help.

Ah, it looks like I should have read your title more carefully. Are the files on the PCs that you want to share with your iMac in a shared folder?
If not, follow the steps on this page to set up shares from Windows 7.
If that is already set up, connect to the share from the iMac using this article.

How to add an AP to a Controller

Hello,
I'm not familiar with the process of how to add an access point to a controller. DHCP with option 43 has been configured for the subnet where the AP will be installed. The AP has obtained an IP address and I'd like to know how to discover it on the controller and add it.
Thanks in advance for your assistance.
Best, ~zK

Hi Zk,
You have to use DHCP option 43 in dhcp pool configured for AP to find out the WLC:
option 43 hex <hexadecimal string>
More info about DHCP Option 43: http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/97066-dhcp-option-43.html
I will try to keep AP and WLC on same subnet.
More info about LAP registartion to WLC:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/70333-lap-registration.html
Regards
Dont forget to rate helpful posts

How does does Wireless and a Wireless card work?

I bought an imac G5 1.8ghz We already have a BT wireless connection and I want to hook up to that. I gather that I need an airport card but I'm not sure how to insert a card into the machine there is a CD portal and ones for USB as well. How does this wireless business work and what do I need for my machine running Tiger 10.4.11?

The AirPort Extreme card appears to be the correct product
but you should be able to tell from some of the Apple Support
information in the form of their product support page for your
specific computer model. The main support section has a side
bar menu of products and if you find iMac G5, then look into it
further, you can identify what exact model iMac G5 you have.
{+If you have looked under the Blue Apple in the Finder menu bar+
+and chosen About this Mac> more info> System Profiler> then,+
+look under Network> Airport card, you can see if one is installed+.}
There are manuals, instructions and other info available, too.
The manual to install the physical AirPort Extreme card is in
the manuals link in the iMac G5 page in Apple Support.
Since there were a few different models of iMac G5, you should
be sure to get the install instructions that match your computer.
The card itself could be used in many different Mac models, so
it will NOT have installation instructions with it for your iMac G5.
{The hardware installation is the point of reference here; not the
CD software, which very likely is outdated and not needed at all.}
Apple - Support - iMac G5 models:
http://www.apple.com/support/imac/g5/
Apple - Support - Manuals:
iMac models (from newer Intel, on back to older)
http://support.apple.com/manuals/#imac
Since the iMac G5 (PPC) and iMac (Intel) look similar, you
will have to identify your computer in the G5 category to
be able to get the correct AirPort installation instruction .pdf.
How to Identify your iMac (note three designs)
http://support.apple.com/kb/HT1463
The software CD included with that older Airport Extreme package
will likely be older than your OS X version in the computer now.
{So, you will NOT need to install that software to use the AirPort card.}
Examples of .pdf download manuals on how to install an Airport card
are as follows (these are actual links to these manuals.) +So, these may+
+not be for your specific iMac G5 computer.+ To be sure, use Identify page.
• _iMac G5 20-inch_ AirPort Extreme Card Replacement Instructions (Do It Yourself Manual)
iMac G5 AirPort Extreme Card, 20-inch 4. Pull the tab on the card to remove the card from
the AirPort card guide. Important:
http://manuals.info.apple.com/enUS/imacG5_20inchAirPort.pdf
• _iMac G5 17-inch_ AirPort Extreme Card Replacement Instructions (Do It Yourself Manual)
iMac G5 AirPort Extreme Card, 17-inch 4. Pull the tab on the card to remove the card from
the AirPort card guide. Important:
http://manuals.info.apple.com/enUS/imacG5_17inchAirPort.pdf
{Since the above are examples, and there were more than two designs, you should
check the ' how to identify your iMac ' page under the iMac G5 and Intel, to be sure.}
Good luck & happy computing!
PS: if your 1.8GHz iMac G5 is a 17" LCD with Ambient Light Sensor, the wireless
AirPort Extreme is a built-in component: Model # M9843 (1.8 GHz) and in the older
1.8GHz iMac G5 20" the card is listed as an Optional part, in pre-light sensor model.
{ edited 2x - to add info }

How to add JetDirect (A2591A) to W7 & Driver for Win7/DesignJet 750c+

Here is what I have:
-HP G71 wireless, windows 7 Home, laptop
-Linksys E2000 wireless Router
-HP JetDirect Ex A2591A
-DesignJet 750c Plus Large Format Plotter (Yes, I know it's old, but it's a backup unit until my 1055cm gets fixed).
Problem #1: I cannot find an HP driver for the DesignJet 750c Plus for windows 7, is there one? If so, where?
Problem #2: How to add JetDirect (A2591A) -750c Plus Plotter to my Windows 7 G71 wireless laptop. While using my wireless router and the JetDirect Ex. It is physically hooked up correctly. I belive that I need to be able to find out what is the I.P. address for the JetDirect, but I've been wrong before. Is there a link to show me how to do this somewhere?
Thank You in advance.

For 64 bit systems you can download the XP x64 drivers from here, then unzip the files into a new folder. Next go to the Devices and Printers folder, Add a Printer, select the proper port, then select "Have a Disk" and point to the folder where you unzipped the files.
To find the IP address the easiest way is to print a config page from the printer front panel.
This forum is focused on consumer level products. For the Designjet you may have better results posting in the HP Designjet forum here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Add wireless printer to my ipad

Im not sure how to add my printer to my iPad

Printing from an iPad or iPhone
To print directly from an iPad you need an AirPrint - enabled printer on the same wireless network as the iPad. All AirPrint printers are wireless but not all wireless printers are AirPrint-enabled.
If you do not have an AirPrint printer, a number of workarounds exist that enable the use of any printer you normally use, even older ones that may predate AirPrint by decades. Search for the following products:
handyPrint (Mac only, donation-supported)
Printopia (Mac only, $19.95 with free trial)
These are utilities you install on the Mac you normally use for printing, enabling it to act as an AirPrint print server. The Mac must be "on" but may be asleep for them to work. The iPad needs nothing else, no iOS apps need to be installed and no configuration is necessary. If your computer can print, so can the iPad, using one of these utilities on your Mac.
Equivalent utilities may exist for PCs but I have no experience with them - I suggest https://www.collobos.com
There are also iOS apps available from printer manufacturers that enable printing directly from your iPad to selected printers. Search for them in the App Store.
You can also buy this standalone hardware print server, bypassing the need for a computer altogether:
http://www.lantronix.com/it-management/xprintserver/xprintserver.html
Otherwise you will need to buy an AirPrint printer or multifunction device. I recommend you consider AirPrint compatible Brother printers and multifunction devices.
Read the reviews and choose wisely.

How to add fields to already loaded cube or dso and how to fill records in

how to add fields to already loaded cube or dso and how to fill it.can any one tell me the critical issues in data loading process..?

This is sensitive task with regards to large volumes of data in infoproviders.
The issue is to reload of data in case of adjusted structures of infoproviders.
Indeed there are some tricks. See following:
http://weblogs.sdn.sap.com/cs/blank/view/wlg/19300
https://service.sap.com/sap/support/notes/1287382

How to add a library (libSomeRandomlib.so) to a project....??

Ok, so I've been trying to get CERN's ROOT program/libraries to work in an xcode project for a while, but I'm running into one really weird error, and I think I may just not know how to add a library to a project correctly.
Suppose I create a new Xcode C++ command line tool project. I hit Build and go, and it gives me a nice little Hello World! in the console, just as it should. If I then click on the project in Groups & Files, go to Project>Add to Project..., and choose, say, libCint.so, from my root/lib directory, and click ok, then click Build & Go, I get an error in the console:
dyld: Library not loaded: @rpath/libCint.so
Referenced from: /Users/paulthompson/Documents/Programming/Build Products/Debug/LibraryIncludeTest
Reason: image not found
sharedlibrary apply-load-rules all
Data Formatters temporarily unavailable, will re-try after a 'continue'. (Cannot call into the loader at present, it is locked.)
My assumption is that either I'm missing a step in the process of adding a library, or else there is something jacked up with the libraries themselves. Anyone have any advice?
Thanks,
Paul
EDIT* Oh, I should mention that the actuall binary that gets built after adding the library WILL execute properly in the Finder, or from terminal, just not with the Build & Go, or Go commands from within xcode.
Message was edited by: TraxusIV

TraxusIV wrote:
Results of otool:
LibraryIncludeTest:
@rpath/libCint.so (compatibility version 0.0.0, current version 0.0.0)
/usr/lib/libstdc++.6.dylib (compatibility version 7.0.0, current version 7.9.0)
/usr/lib/libSystem.B.dylib (compatibility version 1.0.0, current version 123.0.0)
Macintosh-9:Debug paulthompson$ otool -L /Applications/CERNRoot/root/lib/libCint.so
/Applications/CERNRoot/root/lib/libCint.so:
@rpath/libCint.so (compatibility version 0.0.0, current version 0.0.0)
/usr/lib/libSystem.B.dylib (compatibility version 1.0.0, current version 125.2.0)
/usr/lib/libstdc++.6.dylib (compatibility version 7.0.0, current version 7.9.0)
I honestly don't know much about @rpath. I found this page that explains it a bit more: http://blogs.sun.com/dipol/entry/dynamiclibraries_rpath_andmac
So, since I don't want to deploy with the environment variable set, I should ask, what IS the correct, MacOS X way to do it?
The best way to find that is to look at how Apple does it. They put frameworks in /System/Library/Frameworks and regular shared libraries in the standard places. You can do the same. Put your frameworks into /Library/Frameworks and your shared libraries into /usr/local-based paths.
If you want to create stand-alone executables that can be installed via drag-n-drop, you can put shared libraries inside the application bundle. If your shared libraries/frameworks are elsewhere, you will need some sort of installer to get them installed.
I've been sifting through Apple's developer documentation but I have yet to find a concise, straightforward explanation of how to add shared libraries. I'm horribly confused at this point. Is there a good tutorial available anywhere for both the general unix case of linking to dylibs and .so's, and the Mac specific case?
Hopefully someone else knows an answer for this one.
*EDIT* I do already have the variable defined both in ~/.MacOS/environment.plist and also in Xcode as an additional user variable.
I'm not sure about the whole RPATH thing. Setting environment.plist will define environment variables for use in the Finder, but that is really a hack. There are better ways to do it, but if you are porting some open-source programs, that may be the only way. You should be able to define those variables in Xcode. You have to selected the debug executable under "Exectuables"

How to add wireless to a MacPro?

Similar Messages

Maybe you are looking for