How to adjust upper and lower printer margins?

I want to be able to print a 5x7 photo on an A4 sheet so that I can fold it to make a greeting card. Therefore I need to be able to set the top and bottom margins independently like you can in Photoshop. How can I do this? I am using an Epson Stylus Pro 4880 printer and an HP deskjet D2460 printer. Pleas help. I am getting frustrated. Please help with any solutions. Thank you.

Unless your printer driver has such controls you will have to use a third party image editor or page layout program to do this
Old Toad's tutorial #8 describes the process for iPhoto - http://web.mac.com/toad.hall/OldToadsTutorials/No._8.html
LN

Similar Messages

How to set upper and lower limit for service notification in SPRO

Hello everyone,
Good morning....!!
I am new to SAP PM and to SCN as well.
I have a question on Service notification user status.
I have notification profile configured in SAP as below:
Status no      Status          Short text              Lower limit          Upper limit
5                  REGD          Registered                1                          70
10                PCKS            Pack sent                  1                          70
20                APRC            Application received 1                        70
etc..
I want the statusesto be set as navigation should only allow to go back one by one...like from APRC -->PCKS not to REGD.From PCKS -->REGD etc..not vice versa.
Can enayone explain me to how to set lower and upper limits for these according ot the above requirement.
for more details please check my attachment.
Thanks in advance..!!
Regards,
Sudha.

Once you change the status to previous status, just save the order. Then again open the order & try to change the user status.
Just I made replica of your profile. I could able to change (even without saving the order).

How do I remove the background display in the upper and lower parts of the page?

The upper and lower ends have a background display when a new version was updated.I wish to remove the display.
== This happened ==
Every time Firefox opened
== Today

Sounds that you installed a Persona.
You can uninstall that Persona and revert to the ''Default'' theme (Tools > Add-ons > Themes).
See [[Using themes with Firefox]] and http://kb.mozillazine.org/Themes (Lightweight theme)

SAPScript: how tu adjust heigh and width of standard text (logo)?

Hi!
how to adjust heigh and width of standard text (logo)?
I do not want to edit the logo, because it is used elsewhere, so I need to adjust heigh and width when using it in a form.
For now stadard text comes over the window. Here is how I use it:
INCLUDE ZHEX-LOGO OBJECT TEXT ID ST
Will reward,
Mindaugas

Hi Mindaugas,
While uploading using RSTXLDMC. You have to maintain your size of the logo.
Go through below mentioned document.
Upload TIFF files to SAPscript texts
Description
The report RSTXLDMC allows a TIFF graphics file to be uploaded from the file system of the R/3 GUI to a standard text in the R/3 word processor SAPscript. (TIFF is a registered trademark of the Aldus Corporation.)
When uploading, the TIFF graphic is converted either into a black and white raster image (parameter type=BMON ) or as a color raster image with a maximum of 256 colors (parameter type=BCOL).
The black and white raster images ( BMON) can be printed using the following printer types:
PCL-5 printer
PostScript printer
Kyocera PRESCRIBE printer
Device type SAPWIN (with SAPlpd 32-bit as of Version 2.41 for Windows NT or Windows 95)
The color raster images (BCOL) can be printed using the following printer types:
PCL-5 printer with color capability (e.g. HP Color LaserJet). Color graphics are not printed properly on monochrome PCL-5 printers (e.g. HP LaserJet 5), because the printer cannot set the color palette as required and does not perform any gray-level conversion.
PostScript printer (color graphics are automatically converted to gray levels on black and white printers using PostScript) Device type SAPWIN (with SAPlpd 32-bit as of Version 2.41 for Windows NT or Windows 95) During TIFF graphic import, the basic set " Baseline TIFF 6.0 " of the TIFF specification 6.0 is supported.
To maintain compatibility with earlier versions of the report RSTXLDMC, it is also possible to convert the TIFF graphic directly into a black and white raster image for a particular printer type when uploading. These are the three printer types PCL-5 (parameter type=PCL ), PostScript (parameter type=POST) and Kyocera PRESCRIBE (parameter type=PRES ). A raster image uploaded in this manner can only be printed using the appropriate printer type.
Besides TIFF raster graphics, direct printer commands in the respective printer language (PCL-5, PostScript or Prescribe) can also be contained in the file which is to be uploaded (printer macros). They are then transferred to the standard text unmodified.
The graphics are output by inserting the standard text into the document which is to be printed, directly or using an INCLUDE command. The printer commands, which for example draw a company logo on the page, are only output if the print request is processed by the printer driver corresponding to the macro type, otherwise they are ignored. Example: A macro of type PCL is contained in a print request. If the request is output to a printer with type HPLJIIID (to which the driver HPL2 is assigned), the macro data is sent to the printer. If the request is printed on a printer of type POSTSCPT (to which the driver POST is assigned), the output of the macro data is suppressed.
In the standard text, the printer commands are inserted between the HEX ... ENDHEX command lines in hex notation. Various report parameters allow the graphic or printer macro to be placed on the page or at the current text position. Note: When the /:HEX command line which precedes the macro appears in the text, a line break is generally made before the graphic is output. The output of the macro therefore begins in the next text line at the left window border of the current page window, as long as a shift to the right is not specified (see below).
If your own printer macros are uploaded and not TIFF files, you must ensure yourself that the normal (text) output of the driver is not impaired when the printer commands are inserted in the output from the uploaded file. The printer drivers pass the data contained in the file to the printer unmodified, therefore without control over the individual actions this triggers on the printer. For example, syntax errors should not be generated by the PostScript commands (type POST), or form feeds should not be contained in the file (unless this was intended) for PCL-5 (type PCL).
Restrictions:
In general, the output of graphics generated via RSTXLDMC from R/3 is not suitable for mass printing (that is, unless you are using the "Graphic resident on printer" feature): the R/3 spooler has to hold significantly more data in its output files. If the graphics occur several times in a spool request, the data also reoccurs. Apart from this, the network is more heavily loaded in sending the increased volume of data to the printer and the printer output is slowed significantly (varies according to printer model) if raster graphics are output as well as the text.
If your graphics reside on your printer during a printing job, the degree of 'correctness' with which they are printed depends on the amount of memory available in your printer. R/3 print drivers are unable to determine whether the amount of memory available is enough! If one of the graphics that you have marked as resident is not displayed, try reloading the graphic and switching off the parameter "Graphic resident on printer".
When printing black and white graphics on PCL-5 printers, image data is compressed in order to greatly reduce the file size.
The output of graphics and macros on PCL-5 printers, PostScript printers and device type SAPWIN (type BMON, BCOL, PCL, POST) is adapted to the page orientation used, that is if landscape is used instead of portrait, the graphic is also turned when output. This is not the case for the PRESCRIBE printers (type BMON, PRES)! With these printers, the graphic is not automatically turned when landscape is used, but appears on the page in the identical position as for portrait. You are therefore recommended not to output raster images when printing in landscape on PRESCRIBE printers.
PRESCRIBE printers do not support the resolutions 200 and 600 dots per inch when printing raster images.
Not all PCL-5 compatible printers support the resolutions 200 and 600 dots per inch when printing raster images.
TIFF graphics with compression type 2 ("CCITT Group 3 1-Dimensional Modified Huffman run length encoding ") can currently not be imported although this is a component of the Baseline TIFF 6.0 specification for monochrome images.
Color TIFF graphics with full color representation (ie. a lot more than 256 colors) are automatically converted into 256 gray levels when uploading with type BCOL.
When TIFF graphics are converted to black and white raster images (type BMON, PCL, POST, PRES) there is no default simulation of gray levels or colors of the original image on the printer (for example, by using different tones of gray). Each pixel of the original image is converted to a white or black pixel on the printer according to its intensity value.
The parameter "Number of TIFF gray levels" does, however, allow a simulation of gray/colour tones of the original image through levels of gray on the printer, when using type PCL, POST or PRES. This parameter is ignored for type BMON.
The conversion of TIFF graphics can be so time-consuming that it is recommendable to execute the report RSTXLDMC in batch processing. Note: in batch, the file is always read from the file system of the application server (ie. not from the file system of the GUI).
The length of an individual text in the text file is limited. When importing TIFF graphics with very large dimensions, especially if more than 2 gray levels are used, a termination can therefore occur when saving the standard text ("EXPORT_TOO_MUCH_DATA"). This restriction can only be avoided by reducing the TIFF graphics. Note: The display of a raster image in Postscript or PRESCRIBE format needs from two to three times as much space as displaying in PCL-5.
When processing very large TIFF images on PostScript printers, a print termination can occur with PS error message "limitcheck". In this case the internal memory of the printer is insufficient to scale the required raster image. This implementation limit cannot be influenced by changing the report parameters when importing.
Requirement
The file which is to be uploaded can contain the following formats/ commands:
Baseline TIFF 6.0 raster image files. The image information of the TIFF file is converted into black and white/color raster images when uploading. Note: As the TIFF format allows a variety of variants, only a basic set of TIFF 6.0 formats is supported here described in the TIFF 6.0 specification as Baseline TIFF 6.0.
PCL : PCL-5, Hewlett Packard Printer Control Language 5 for HP LaserJet 3, 4, 5 series and compatible printers. The data is output by the printer driver HPL2 only.
PRES: Kyocera PRESCRIBE for Kyocera laser printers. The data is output by the printer driver PRES only.
POST: Adobe PostScript or EPS format (encapsulated PostScript ) for PostScript printers. The data is output by the printer driver POST only. In the upload, one of the end-of-file markers (CTRL-D, hex $04) which may be contained in the PostScript file is not transferred.
For PostScript files which contain a bounding box entry (for example, all EPS files) the macro/graphic can be scaled to a size specified by the user. In this case, a small lead text and trailer are generated by the report for the macro data and inserted in the standard text.
Parameters of RSTXLDMC
File name
Path and file name of the file to be uploaded in the file system of the R/3 frontend (dialog processing) or in the file system of the application server (batch processing)
Type
Way which the data contained in the file is to be converted. Possible values are BMON, BCOL, PCL, POST and PRES. With parameter values BMON and BCOL, a TIFF 6.0 file is expected. This is converted into either a black and white raster image (BMON) or a color raster image (BCOL). These raster images are printer-independent and can be printed using various printer types (see above).
With parameter values PCL, POST and PRES, either a TIFF 6.0 file or a file with printer commands in the appropriate printer langauge is expected. If the file is a TIFF file, it is converted into a black and white raster image for the printer type specified in the parameter. The presence of a TIFF file is recognized automatically. If the file is not a TIFF file, the file contents are regarded as the printer macro of the respective type. Data loaded with type PCL, POST or PRES can only be printed on the respective printer type.
Resolution for TIFF raster images
Resolution which should be used when importing a TIFF raster image, in dots per inch (dpi). If an allowed value is entered here, this overrides the resolution information in the TIFF file. The allowed values are:
75 dpi
100 dpi
150 dpi
200 dpi (not for type PRES, for PCL only HP LaserJet 4,5 series)
300 dpi
600 dpi (not for type PRES, for PCL only HP LaserJet 4,5 series)
Changing the resolution affects the size of the graphic on the printer. If a resolution of 300 dpi is stated in the TIFF file and this parameter is set to 75 dpi, the graphic is four times as big when printed as at the outset.
Note: Kyocera PRESCRIBE printers do not support 200 and 600 dpi resolutions.
Note: Not all PCL-5 printers support resolutions 200 and 600 dpi, for example HP LaserJet 3 series does not, but LaserJet 4 and 5 series do.
Graphic Resident on Printer
Normally, graphics that occur more than once in a printing job (a company logo that appears on each page, for example) are sent to the printer repeatedly each time they are needed. In order to avoid this kind of redundancy, you can select this checkbox on the selection screen. The R/3 print driver then stores the graphic in the printer's memory and the printer retrieves the 'resident' graphic memory every time that re-occurs in your job.
Caution: Whether or not the printer correctly reproduces the graphic depends on the amount of memory available in the printer during the printing job! You should avoid using this feature with color graphics since they take up a lot more memory than monochrome graphics.
This parameter can only be used with types "BMON" and "BCOL".
Absolute positioning
Determines whether the macro/graphic is positioned absolutely or is to be output at the current text position. If this checkbox is selected, the graphic is positioned absolutely (parameters "X-position" and "Y-position" are used), if this checkbox is not selected, the graphic is positioned at the current text position (parameters "Reserved height" and "Shift to right" are used)
Absolute X-position
Horizontal position (space from left border) of the macro/graphic, if absolute positioning is required. This is the parameter XPOS of the HEX command.
Absolute Y-position
Vertical position (space from upper border) of the macro/graphic, if absolute positioning is required. This is the parameter YPOS of the HEX command.
Reserve height automatically
If this checkbox is selected, the system automatically inserts the actual height of the graphic during printing into the subsequent "Reserved height" parameter.
Reserved height
If positioned at the current text position, this parameter specifies the horizontal spacing to be reserved for the macro/graphic, which must not be printed with text from the paragraph. This is the parameter HEIGHT of the HEX command.
Shift to right
If positioned at the current text position, this parameter specifies the space between the left border of the macro/graphic and the left border of the page window. If this value is increased, the macro/graphic is shifted to the right. This is the parameter LEFT of the HEX command.
Unit of measurement for positioning
The unit of measurement in which the position values (X,Y, height, shift) are specified. Possible values are CM (centimeters), MM (millimeters), IN (inches), PT (typographic point = 1/72 inch), TW (1/20 point = 1/1440 inch)
Text title
Comment used for the attribute "Title" of the standard text generated as well as as a comment line in the text itself
Line width
Number of columns to be used in the standard text when generating the HEX...ENDHEX command lines. The default value is 132
Text name
Name of the standard text to be generated. If an * character occurs in the name, it is replaced by the value of the parameter "Printer type". For example, if the entry is ZHEX-IMAGE1-* and the printer type = PCL, the text name ZHEX-IMAGE1-PCL is generated. The default value for the name is ZHEX-MACRO-<printer type>, but the standard text can be named as required (take into account customer reserve). Standard texts are client-dependent!
Note: The name of a standard text can be up to 32 characters long !
Text ID
ID of the standard text to be generated. The default value is ST (general standard texts)
Text language
Language key of the standard text to be generated. The default value is the logon language
PostScript scaling
Flag which determines how the macros/graphics of type POST are handled. If set to 'X', the report expects a PostScript comment line in the file
%%BoundingBox llx lly urx ury (e.g. %%BoundingBox -1.5 0 21.4 14.1)
as present, for example, in all EPS files, in which the dimensions and the position of the macro/graphic are specified (if a bounding box comment is not included, 0 0 1 1 is assumed as the default value). This information is then used by the report to insert PostScript commands which scale the macro/graphic to the size specified in the parameters "Width" and "Height" (listed below).
If the flag is set to ' ' (blank), the PostScript file is transferred to the standard text without any additions (any transformations to the coordinate system used by the printer driver must already be contained in the file).
The flag must be set to 'X' for the import of TIFF files for type POST.
Width according to PS scaling
Required width of the macro/graphic if the flag PostScript scaling is set. Can remain at zero for the import of TIFF files, the size is then determined by the resolution of the graphic.
Height according to PS scaling
Required height of the macro/graphic if the flag PostScript scaling is set. Can remain at zero for the import of TIFF files, the size is then determined by the resolution of the graphic.
If you want to scale the PostScript graphic with these parameters, one of the two values, width or height, can be specified with zero. The graphic is then scaled so that the width-to-height ratio remains unchanged and the original graphic is not distorted.
Unit of measurement for PS scaling
Unit of measurement in which the parameters "Width" and "Height" are specified. Possible values are CM (centimeters), MM (millimeters), IN (inches), PT (typographic point = 1/72 inch), TW (1/20 point = 1/1440 inch)
Number of TIFF gray levels
Number of gray tones which are to be used on the printer for displaying the original image. Note: This parameter is only evaluated when using types PCL, POST or PRES!
Possible values are 2,4,9. With the default value 2, each pixel of the original image is converted either to a white or a black pixel on the printer. With the value 4, each pixel of the original image is converted on the printer with 4 pixels, which simulate 4 different gray levels. With the value 9, each pixel of the original image is converted on the printer with 9 pixels which simulate 9 different gray levels.
Note: With values 4 or 9 the resolution of the image is doubled or tripled. The restrictions on the possible resolutions (see previous parameter) then apply for the resulting resolution.
Output
Individual steps of the upload procedure are logged in the report list generated and, if necessary, errors reported. The uploading of TIFF graphics, in particular, is cancelled if there is a variant which is not supported. A message to this effect is then issued. If execution is successful, the report generates a standard text with the key specified in the parameters. If the standard text already exists, a window appears with a warning before the text is overwritten.
Regards,
Ameer Baba.

UPPER and lower case file extensions for Photo Shop Elements using Windows 7

How do I persuade WIndows 7 to show both UPPER and lower case file extensions, which is a very useful facility offered by my ancient, 2002, version of Photoshop Elements? When processing large volumes (100 plus) photos it is very useful to be able to spot those that have been processed among those awaiting my gentle touch. The JPEG file extension produced by my camera is UPPER case so by using "Save as" with lower case the modified photos are immediately spotted. This worked fine on Windows XP and the same programme has loaded and works well on my new laptop which came loaded with Windows 7 EXCEPT that it persists in using UPPER case all the time, irrespective of the preference settings in PSE. HELP!
Camperman1

In PSE there is a facility "File > process multiple files".
Using this facility you can actually process multiple files at one go and you can easily rename images.
Addi

How do I set the default print margins for ALL printers in mozilla.cfg

How do I set the default print margins for ALL printers in mozilla.cfg, even ones that are not yet installed / connected to the computer?
I'm trying to install firefox with MDT and apply certain print options, but the printers themselves are connected at a later stage so the print.printer_myprinterhere cannot be used.

Best answer I could find: [https://mike.kaply.com/2012/03/16/customizing-firefox-autoconfig-files/#comment-132668]
If you can figure out how to add the printer name, this can be used to lock the margins.

Read the signal value that pass over the upper and lower limit..

how to create the system which can read the signal value that pass the lower and upper limit? i've try but the system only read the value that in range of upper and lower limit..thanks..

Im not very sure if this system can read the value that pass over the limit..because at the save file data so many value(i will attach that file)..and i dont know how to setting to get the failure values only..
Actually i want to build some system that can read and save value that pass over the limit..i take the signal from simulation sine signal..no hardware required..
im very new with this software and im in learning process..
A very big thanks to all that helping me..
save file data from the system
Channels 8
Samples 1 1 1 1 1 1 1 1
Date 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05
Time 12:30:11.099999 12:30:11.216 12:30:11.216 12:30:11.216 12:30:11.099999 12:30:11.216 12:30:11.216 12:30:11.216
X_Dimension Time Time Time Time Time Time Time Time
X0 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1
Delta_X 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000
***End_of_Header***
X_Value Sine (Negative Peak) Failures (Negative Peak) Upper Limit (Negative Peak) Lower Limit (Negative Peak) Sine (Positive Peak) Failures (Positive Peak) Upper Limit (Positive Peak) Lower Limit (Positive Peak) Comment
0.100000 -6.999066 -6.999066 5.000000 -5.000000 6.999136 6.999136 5.000000 -5.000000
0.200000 -6.998993 -6.998993 5.000000 -5.000000 6.999204 6.999204 5.000000 -5.000000
0.300000 -6.998917 -6.998917 5.000000 -5.000000 6.999269 6.999269 5.000000 -5.000000
0.400000 -6.998838 -6.998838 5.000000 -5.000000 6.999331 6.999331 5.000000 -5.000000
0.500000 -6.998756 -6.998756 5.000000 -5.000000 6.999391 6.999391 5.000000 -5.000000
0.600000 -6.998672 -6.998672 5.000000 -5.000000 6.999447 6.999447 5.000000 -5.000000
0.700000 -6.998585 -6.998585 5.000000 -5.000000 6.999501 6.999501 5.000000 -5.000000
0.800000 -6.998495 -6.998495 5.000000 -5.000000 6.999552 6.999552 5.000000 -5.000000
0.900000 -6.998403 -6.998403 5.000000 -5.000000 6.999601 6.999601 5.000000 -5.000000
1.000000 -6.998307 -6.998307 5.000000 -5.000000 6.999646 6.999646 5.000000 -5.000000
1.100000 -6.998209 -6.998209 5.000000 -5.000000 6.999689 6.999689 5.000000 -5.000000
1.200000 -6.998108 -6.998108 5.000000 -5.000000 6.999729 6.999729 5.000000 -5.000000
1.300000 -6.998005 -6.998005 5.000000 -5.000000 6.999766 6.999766 5.000000 -5.000000
1.400000 -6.997898 -6.997898 5.000000 -5.000000 6.999801 6.999801 5.000000 -5.000000
1.500000 -6.997789 -6.997789 5.000000 -5.000000 6.999833 6.999833 5.000000 -5.000000
1.600000 -6.997677 -6.997677 5.000000 -5.000000 6.999862 6.999862 5.000000 -5.000000
1.700000 -6.997563 -6.997563 5.000000 -5.000000 6.999888 6.999888 5.000000 -5.000000
1.800000 -6.997445 -6.997445 5.000000 -5.000000 6.999912 6.999912 5.000000 -5.000000
1.900000 -6.997325 -6.997325 5.000000 -5.000000 6.999932 6.999932 5.000000 -5.000000
2.000000 -6.997202 -6.997202 5.000000 -5.000000 6.999950 6.999950 5.000000 -5.000000
2.100000 -6.997076 -6.997076 5.000000 -5.000000 6.999965 6.999965 5.000000 -5.000000
2.200000 -6.996948 -6.996948 5.000000 -5.000000 6.999978 6.999978 5.000000 -5.000000
2.300000 -6.996817 -6.996817 5.000000 -5.000000 6.999988 6.999988 5.000000 -5.000000
2.400000 -6.996683 -6.996683 5.000000 -5.000000 6.999994 6.999994 5.000000 -5.000000
2.500000 -6.996546 -6.996546 5.000000 -5.000000 6.999999 6.999999 5.000000 -5.000000
2.600000 -6.996546 -6.996546 5.000000 -5.000000 7.000000 7.000000 5.000000 -5.000000
2.700000 -6.996683 -6.996683 5.000000 -5.000000 6.999994 6.999994 5.000000 -5.000000
2.800000 -6.996817 -6.996817 5.000000 -5.000000 6.999988 6.999988 5.000000 -5.000000
2.900000 -6.996948 -6.996948 5.000000 -5.000000 6.999978 6.999978 5.000000 -5.000000
3.000000 -6.997076 -6.997076 5.000000 -5.000000 6.999965 6.999965 5.000000 -5.000000
3.100000 -6.997202 -6.997202 5.000000 -5.000000 6.999950 6.999950 5.000000 -5.000000
3.200000 -6.997325 -6.997325 5.000000 -5.000000 6.999932 6.999932 5.000000 -5.000000
3.300000 -6.997445 -6.997445 5.000000 -5.000000 6.999912 6.999912 5.000000 -5.000000
3.400000 -6.997563 -6.997563 5.000000 -5.000000 6.999888 6.999888 5.000000 -5.000000
3.500000 -6.997677 -6.997677 5.000000 -5.000000 6.999862 6.999862 5.000000 -5.000000
3.600000 -6.997789 -6.997789 5.000000 -5.000000 6.999833 6.999833 5.000000 -5.000000
3.700000 -6.997898 -6.997898 5.000000 -5.000000 6.999801 6.999801 5.000000 -5.000000
3.800000 -6.998005 -6.998005 5.000000 -5.000000 6.999766 6.999766 5.000000 -5.000000
3.900000 -6.998108 -6.998108 5.000000 -5.000000 6.999729 6.999729 5.000000 -5.000000
4.000000 -6.998209 -6.998209 5.000000 -5.000000 6.999689 6.999689 5.000000 -5.000000
4.100000 -6.998307 -6.998307 5.000000 -5.000000 6.999646 6.999646 5.000000 -5.000000
4.200000 -6.998403 -6.998403 5.000000 -5.000000 6.999601 6.999601 5.000000 -5.000000
4.300000 -6.998495 -6.998495 5.000000 -5.000000 6.999552 6.999552 5.000000 -5.000000
4.400000 -6.998585 -6.998585 5.000000 -5.000000 6.999501 6.999501 5.000000 -5.000000
4.500000 -6.998672 -6.998672 5.000000 -5.000000 6.999447 6.999447 5.000000 -5.000000
4.600000 -6.998756 -6.998756 5.000000 -5.000000 6.999391 6.999391 5.000000 -5.000000
4.700000 -6.998838 -6.998838 5.000000 -5.000000 6.999331 6.999331 5.000000 -5.000000
4.800000 -6.998917 -6.998917 5.000000 -5.000000 6.999269 6.999269 5.000000 -5.000000
4.900000 -6.998993 -6.998993 5.000000 -5.000000 6.999204 6.999204 5.000000 -5.000000
5.000000 -6.999066 -6.999066 5.000000 -5.000000 6.999136 6.999136 5.000000 -5.000000
5.100000 -6.999136 -6.999136 5.000000 -5.000000 6.999066 6.999066 5.000000 -5.000000
5.200000 -6.999204 -6.999204 5.000000 -5.000000 6.998993 6.998993 5.000000 -5.000000
5.300000 -6.999269 -6.999269 5.000000 -5.000000 6.998917 6.998917 5.000000 -5.000000
5.400000 -6.999331 -6.999331 5.000000 -5.000000 6.998838 6.998838 5.000000 -5.000000
5.500000 -6.999391 -6.999391 5.000000 -5.000000 6.998756 6.998756 5.000000 -5.000000
5.600000 -6.999447 -6.999447 5.000000 -5.000000 6.998672 6.998672 5.000000 -5.000000
5.700000 -6.999501 -6.999501 5.000000 -5.000000 6.998585 6.998585 5.000000 -5.000000
5.800000 -6.999552 -6.999552 5.000000 -5.000000 6.998495 6.998495 5.000000 -5.000000
5.900000 -6.999601 -6.999601 5.000000 -5.000000 6.998403 6.998403 5.000000 -5.000000
6.000000 -6.999646 -6.999646 5.000000 -5.000000 6.998307 6.998307 5.000000 -5.000000
6.100000 -6.999689 -6.999689 5.000000 -5.000000 6.998209 6.998209 5.000000 -5.000000
6.200000 -6.999729 -6.999729 5.000000 -5.000000 6.998108 6.998108 5.000000 -5.000000
6.300000 -6.999766 -6.999766 5.000000 -5.000000 6.998005 6.998005 5.000000 -5.000000
6.400000 -6.999801 -6.999801 5.000000 -5.000000 6.997898 6.997898 5.000000 -5.000000
6.500000 -6.999833 -6.999833 5.000000 -5.000000 6.997789 6.997789 5.000000 -5.000000
6.600000 -6.999862 -6.999862 5.000000 -5.000000 6.997677 6.997677 5.000000 -5.000000
6.700000 -6.999888 -6.999888 5.000000 -5.000000 6.997563 6.997563 5.000000 -5.000000
6.800000 -6.999912 -6.999912 5.000000 -5.000000 6.997445 6.997445 5.000000 -5.000000
6.900000 -6.999932 -6.999932 5.000000 -5.000000 6.997325 6.997325 5.000000 -5.000000
7.000000 -6.999950 -6.999950 5.000000 -5.000000 6.997202 6.997202 5.000000 -5.000000
7.100000 -6.999965 -6.999965 5.000000 -5.000000 6.997076 6.997076 5.000000 -5.000000
7.200000 -6.999978 -6.999978 5.000000 -5.000000 6.996948 6.996948 5.000000 -5.000000
7.300000 -6.999988 -6.999988 5.000000 -5.000000 6.996817 6.996817 5.000000 -5.000000
7.400000 -6.999994 -6.999994 5.000000 -5.000000 6.996683 6.996683 5.000000 -5.000000
7.500000 -6.999999 -6.999999 5.000000 -5.000000 6.996546 6.996546 5.000000 -5.000000
7.600000 -7.000000 -7.000000 5.000000 -5.000000 6.996546 6.996546 5.000000 -5.000000
7.700000 -6.999994 -6.999994 5.000000 -5.000000 6.996683 6.996683 5.000000 -5.000000
7.800000 -6.999988 -6.999988 5.000000 -5.000000 6.996817 6.996817 5.000000 -5.000000
7.900000 -6.999978 -6.999978 5.000000 -5.000000 6.996948 6.996948 5.000000 -5.000000
8.000000 -6.999965 -6.999965 5.000000 -5.000000 6.997076 6.997076 5.000000 -5.000000
8.100000 -6.999950 -6.999950 5.000000 -5.000000 6.997202 6.997202 5.000000 -5.000000

MIC with different upper and lower limit

Hi experts,
I have a scenario where I have a characteristic to be tested for trace element in a chemical.
But the upper and lower specification of this MIC is different for different chemicals (material numbers) . ie the specification depends on chemical (material) to be inspected.
So I am stuck with a combination a number of MICs with same trace element (say iron) to be tested for a number of chemicals.
How does QM handle this scenario ?
Rgds
JMG

1st - Are you batch managed? if so you can create a batch class and add a general characteristic to it linked to a single MIC. Use this MIC in your inspection plans. Then in the batch class set the specs limits.
You can create a separate batch class for each group of materials. I.e. those with the same specs.
You can also modify the spec value in the classification view for each material that is different then the spec in the class.
You can also create plans which use the same MIC but in the plan you unlock it and set the spec. Then assign all the materials using that spec to the same plan.
This is all very simplied above. But under NO circumstances should it be necessary to create multiple MICS for the same test with all different specs!
Craig

Upper- and lower case filenames

I have two Mac OS Extended (journaled) drives with one on my laptop and one on my desktop. I sometimes get an error that reads:
"You can't copy some of these items because their names are the same as other items on the destination volume, and that volume does not distinguish between upper and lower case letters in filenames. Do you want to skip these items and continue copying other items?"
Recently this happened when trying to force move (using the Command Key) data from my iDisk to my desktop hard drive.
Does anyone know what is going on here?
Is it advisable to first copy data to the desktop on the volume that you are moving to and then move it onto the harddrive and if so what is the reason for this?
Thanks,
Jon

Hi Kappy.
Thanks. Good information. Are you saying you can only /move/ across filesystems or disk volumes or are you saying you can only /copy/ across filesystems or disk volumes.
My impression was that going from one hard drive to another hard drive - that the default was copy, but that you could force a move by holding down the Command Key. When I do this over here the little green plus symbol goes away seeming to imply that it is moving. However, /sometimes/ the dialog says it is Copying and sometime is says it is Moving.
The problem is when it craps out in the middle of a Move (or a Copy). Ignoring the dupe file names with caps issue for the moment - what are you supposed to do when you get through a Move or a Copy (from Hard Drive to Hard Drive for instance) and Finder presents you with an error?!
My understanding of your explanation is that Finder has gotten part way through a Copy and/or (?!) part way through an Erase.
Is there any way of understanding WHERE it has gotten when it says it cannot complete an operation because filexyz.pdf is in use (even when it is not)? If I am moving 100 GB of data (or whatever) how am I supposed to know if it has only Copied some information, Copied and Erased some information, Moved some information, or Moved and Erased some information?
Irrespective of the amount of data, when you get to the point that you cannot reasonably be expected to manually sort through this data how in the world am I supposed to know what Finder has done? More importantly, what is the best way to get back to a point at which you know what information is where?
Thanks,
Jon
P.S. I'm moving data in Target Disk mode at this point and I am not getting errors like "The operation can't be completed because an item with the name "folder 100" already exists - WHEN I HAVE ALREADY SELECTED APPLY TO ALL AND OVERWRITE EXISTING FILES.

Upper and lower case Username creates Contact, Calendar, Note acces problems

Dear All
Maybe someone has a solution for this or discovered the same case. Our server infrastructer is using Username with upper and lower case letters e.g "Galler".
Pushing these access data (Username, server adress etc.) for E-Mail, Contact, Calendar and Notes via the profile manager creates problems for the Contact, Calendar and Notes access, because profiles is rechanging the username in all lower case letters "galler". For the E-Mail it is not the case.
Every help would be very appreciated. Maybe some solution in using username alias with only lower case letters, but I don't no how to establish.
Thanks in advance for your help.

Perre wrote:I'm used to being able to pick one or a couple of songs and then adding it a specified playlist. Is this impossible in sonata?
It's clearly not impossible, just different than you expect. Create your playlist as you want it to appear in the Current tab (meaning don't dump every single song from your library in there, just the ones you want) and then save the playlist.
Perre wrote:And if I try to play the m3u file created (the one with every song listed) through freevo I get a message that the directory is empty. What am I doing wrong??
Look at save_absolute_paths_in_playlists in your mpd.conf.

Graph of Multiple Numeric Result displaying measurements and upper and lower limits

Is there a way with your graph control to show all the measured values against upper and lower limits in the same graph?. I can display individual lines, but would like to show all the data on the one graph. The woefully cryptic help files you provide with the graph control in TestStand seriously needs attention (Give examples!) also axis labelling, how is that achieved?

Hey Brian,
I'm not sure I understand what you're wanting to see with the data plotted on the graph--would it be possible for you to show us an example, even if it's just a drawn mockup of what the graph would look like? I'd like to look into it a bit and confirm that there is not a way to display the data.
Also, could you provide a bit of detail about the problems you've run into with using external languages with the ATML and XML reports? I'd like to understand that issue a bit better as well to determine how we could address it.
One thing you might be interested in is that we can currently embed images in the report by inserting HTML code linking to the image. I've seen cases where a LabVIEW VI plotted some data onto a custom graph, saved a picture of the control, and linked the image into the report. Here is a KnowledgeBase article which describes how the linking process works: http://digital.ni.com/public.nsf/allkb/D98A271E30431C9D86256C230079843A?OpenDocument
I'll look forward to your reply about what you're hoping to see, and perhaps we can think of the best way to accomplish it with the reporting mechanism in TestStand. As Chiara mentioned, if there are features you would like to see that are not currently possible with our reports, the Idea Exchange will be a great place to post that.
Thanks!
Daniel E.
TestStand Product Support Engineer
National Instruments

Meter reading upper and lower limits

Hello,
Does anyone know how the structure REL16_RANGE in the form class IS_U_DM_MR_DOWNLOAD gets filled? I need to find the place where the upper and lower limits are filled and how to manipulate, i.e. to correct them. Where, which table, are these values coming from?
thanks,
melinda

GO to se38 t-code give report name IEEL16R2
Line no : 2287.
form fill_reading_ranges using x_reading like t_reading
                                                 y_ranges like rel16_range.
This form wil fill your structure REL16_RANGE.
first it will serach for the billing documnet...then it will find out the rate category,rate then it will search for the tolearnce limit.
Then Upper limit.
      convert lower limit 1 MR result into display format*
        call function 'ISU_METER_IDDATA_TRANSFORM'
      convert upper limit 1 MR result into display format*
        call function 'ISU_METER_IDDATA_TRANSFORM'
Please let me know if you need any more information.
Regards,
Siva

My SD video keeps jumping between the upper and lower frames. So the video starts frame blending and blurring in and out.

My SD video keeps jumping between the upper and lower frames. So the video starts frame blending and blurring in and out. The sequence settings are set to
Editing Mode: DV NTSC 29.97 frames/second.
Pixel Aspect Ration: D1/DV NTSC (0.9091)
Fileds: Lower Field First
Display Format: 30fps Non-Drop-Frame Timecode
720 x480

What is the source of your video, and exactly what is inside your video?
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download

How do I change page setup print margins from Milileters to inches?

How do I change page setup print margins from Milileters to inches?

This has to do with selecting the paper size in the print setup. If you select a (European) paper format that uses millimeters then the margins are in millimeters. To get inches just select an American paper format.

Datatable for upper and lower limit maintained in Measuring Point.

Hi,
I am making use of user exit : IMCR0001. User exit generates maintenance order for measuring reading which are beyong the range maintained in measruing point.
I have create measuring point with characteristics as TEMPERATURE. I have maintained upper limit : 1500 C & lower limit : 1200 C.
When I check datatable IMPTT and look for upper and lower limit, it is showing me : Upper range :1.7731500000000001E03 Lower range : 1.4731500000000001E03
Why is that I can not find the actual value as 1500 and 1200 n the datatable?
In which datatable I can find these values?
Kindly help.
Thanks in advance.
Regards,
TOM.

Hi Tom,
These are system Generated Values, but they will be concatenated by a few Zeros, but you can always find the exact value,
I am able to see the Values correctly in my system follower by some 10-12 zero's "E"+ 02 or 03.
but can check the values
can cross check the Characteristics for the same measuring point?
Regards,
Yawar Khan

How to adjust upper and lower printer margins?

Similar Messages

Maybe you are looking for