How to apply patch 118833-36 on a containerized server?
We have a V890 running Solaris 10 that has two zones (containers) running instances
of Oracle database. `smpatch' won't install patch 118833-36 in the normal manner
because it's flagged as an interactive patch. The recommended procedure is to shut
the server down, boot it in single-user mode and then apply the patch this way:
# cd /var/sadm/spool
# smpatch add -i 118833-36
Then, you are supposed to shut it down again, do a reconfiguration boot, and finally
run smpatch again to apply the remaining patches.
Will this procedure work for a server with containers? I understand that the zones have
to be running for the patch upgrade to succeed. Is there a way to boot the zones into
single-user mode as well? We need to ensure that Oracle doesn't start during the
patch procedures.
Log into the global zone and run :
# shutdown -y -g0 -is
This should bring down the global zone to su mode and halt the other zones (notice Halt)
However I believe there is a bug presently where this does not always happen and you are still able to telnet to the local zones.
Local zone admin could always run zoneadm -z <zone-name> halt on each zone (notice halt not single-user).
Once global zone in in single-user mode install the patch as normal, when the global is done it will bring up each local zone to single-user mode to add the patch too.
118833-36 may need patch add and -G option as this patch also has been experiencing some issues, in which case I believe you would need to do the patch add process on each zone manually
Once the global zone is brought back up again it should bring up the local zones as well.
Let us know if you experience the locals not being halted as mentioned above and need to do it manually.
Similar Messages
-
How to apply patch to forms 6i and report 6i version
Hi to All,
Can any give any link or Metalink Doc ID or any method to how to apply patch to forms and reports 6i in cleint server architecture.
Thanks and Regards
imranHi user622720
Pls Check this Link
Pls verify this as an example:
MyProject =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = servername)(PORT = 1540))
(CONNECT_DATA =(SID = TEST))
and change the bold fields as required according to ur application..!
Hope it Helps,
Regards,
Abdetu.. -
How to apply patches to SP16?
Hi,
I am looking for a clear direction of how to apply patches to the J2EE Engine 6.40 SP16 to SP20. I have NW04, and the patch level is 102141.313. Please tell me how to start. Thank you.
Regards,
-NapadolHi,
Download te following file from service markeplace
CTRLMSS20_0-20001822.SAR
J2EERT20_0-10001982.SAR
J2EERTOS20_0-20001822.SAR
SAPINST20_0-20001822.SAR
Uncar these SAR files
Hope you know how to uncar these files.
After Uncarring two folders will be generated.
J2EE-RUNT-CD
SAPINST-CD
Run the <b>sapinst</b> present within the SAPINST-CD folder.
Choose the option Import support package.
This will patch the engine from SP16 to SP20
Any queries revert back.
Do reward poits.
Regards,
Nayana -
How to apply patches by using solution manager system?
HELLO FRIENDS,
when i download the patch SAPKB70012 & next level patches from service market place, it says that we have to apply the following packages by using maintenance optimizer(solution manager). here i have solution manager4.0., please any one let me know how to configure the maintenance optimzr and how to apply support packages by the solution manager system.
Thanks&Regards
Farkath.CHello
Solman will not implement the files you can download the files using Solman. You need to move the downloaded files to application server and implement them for that you need to configure MoPZ
You can go to server market place service.sap.com/RKT in that select Solution manager.
You will have to select the product as solution manager 7.0 and in technology consultants and system administrator you will find the configuration documentations in for for SIM files.
You can use that and learn how to configure the optimizer on the system.
Then you can download the files and implement the same.
Regards
Vivek -
How to apply patches if application installed multinode type
I have installed the 11.5.10.2 applications with multinode type
node A contains Forms, web and Dbtier
node B contains admin and concurrent.
In my case how do i apply patches( U Driver)
I started applying pathes from Node B went smoothly, but
If start applying patches on node A it showing some errorswhile applying 5985992 on node B , the fallowing erros is showing
AutoPatch error:
Error while executing statement
AutoPatch error:
ORA-06550: line 3, column 10:
PLS-00302: component 'IS_PATCH_APPLIED2' must be declared
ORA-06550: line 3, column 1:
PL/SQL: Statement ignored
I fallowed the metalink doc 556785.1, Now the error is resolved but is it necessary to apply u5985992.drv on both the nodes -
I'm trying to apply patches to dbxml 2.2.13.
I'm pretty sure I'm alone in finding this tricky...but here goes:
Each patch seems to need some different -p arg to strip some arbitrary bit of the path. Am I missing something obvious here?
A couple (eg patch 6 shown below) don't work (I tried downloading using different browsers just in case they're not saving plaintext right)...
patch -p1 < ../patch.2.2.13.6
missing header for context diff at line 3 of patch
(Stripping trailing CRs from patch.)
patching file src/dbxml/nodeStore/NsEventGenerator.cpp
Hunk #1 FAILED at 357.
1 out of 1 hunk FAILED -- saving rejects to file src/dbxml/nodeStore/NsEventGenerator.cpp.rej
Again, I've not used patch before so apologies for being thick.Jacoby,
I think you're right. The patch files have somehow become inconsistent that way. The code portions are still correct.
I'll look into fixing this, but in the mean time, if you hand edit the patch files so that the relative paths to the individual files involved is consistent, they'll work better.
Regards,
George -
How to apply patch on database 9.2.0.1.0
Please any body can send patch applying procedure. I want to apply patch on 9.2.0.1.0 to new release.
ThanksWhat do you mean by 'new release' in your thread? 9.2.0.8.0 is not the new release, but the latest and the last patchset for 9iR2.
You should download from metalink the patchset corresponding to your platform (actually not specified either) using your valid CSI.
~ Madrid -
How to apply patch on Kernal for ECC 5.0?
Hi,
I have installed a new SAP ECC 5.0 system. The release verion shows the current Release as 6.4 and Patch Level 43. Now I want to apply the latest patch on Kernal.
Can any one please provide me the steps for
1). How to proceed with the Kernal upgarde?
2). Which all files to be downloaded from Service Marketplace before proceeding
with the upgrade?
3). Any configurations/back up to be done before starting with upgradation?
4). Any document for the upgradation of Kernal.?
5). How to confirm whether the upgradation has been done sucessfully?
Please reply ASAP!
Thanks in advance.
Regards,
ManishHI
For latest patches you can check at
http://service.sap.com/swdc -> Support Packages and
Patches -> Entry by application -> Application Components
-> SAP ERP -> ERP2004 -> SAP ECC Server
There are two kinds of kernal files:
SAPDBEXE and SAPEXE,one is DB dependent and one file is DB independent.
For downloading the kernal patch:Follow the below path as per your OS and DB combination
for downloading a kernel patch
go through following
service.sap.com/swdc
downloads-> SAP Support packages -> My Company's Application Components -> SAP KERNEL 32 bit ->SAP KERNEL 4.6D 32-BIT ->SAP KERNEL 4.6D 32-BIT->Windows Server on IA32 32bit -> Select ur database->Windows Server on IA32 32bit
Reward suitable points -
Hi All,
I am working on xapps for Mobile to implement CRM mobile sales for handheld using CRMHH 5.0. For that I am using the WAR file MSAHH02_0-10003081.ZIP( xMSA FOR HH (WITH CRM) 5.0 SR02 ) available on SAP marketplace.
Now I want to apply the patch available for the same i.e. MSAHH02P_4-10003081.ZIP(Patch for MSA FOR HH (WITH CRM) 5.0 SR02 )
Can anyone please tell the procedure to apply the patch.
Thanks & Regards
SumitHI
For latest patches you can check at
http://service.sap.com/swdc -> Support Packages and
Patches -> Entry by application -> Application Components
-> SAP ERP -> ERP2004 -> SAP ECC Server
There are two kinds of kernal files:
SAPDBEXE and SAPEXE,one is DB dependent and one file is DB independent.
For downloading the kernal patch:Follow the below path as per your OS and DB combination
for downloading a kernel patch
go through following
service.sap.com/swdc
downloads-> SAP Support packages -> My Company's Application Components -> SAP KERNEL 32 bit ->SAP KERNEL 4.6D 32-BIT ->SAP KERNEL 4.6D 32-BIT->Windows Server on IA32 32bit -> Select ur database->Windows Server on IA32 32bit
Reward suitable points -
How to apply patches to BW instance
we have NW04 SR1 software.
Using the SAPINST gui we installed WebAS Unicode with Java Add-in.
We did a client copy 010 for XI and 020 fro BW. (We want to maintain different clients for XI and BW).
Then we installed the BW UDI Component, XI and Adapter Engine.
We started applying the patches - Servcie Pack 18.
ABAP patches went well.
While installing the J2EE patches,I have to specify the client. So I specified the XI client 010 and installed the J2EE patches.
Now my question is - do install the J2EE patches for BW purpose with client 020?
If so, will there be any conflict between the install done with client 010?
Please advise.
Thanks,
Bhaskarclosing - no answer
-
How to apply Qos in the precedence of cache server
m in an isp and iwant to apply the QOS to enhance my network internet performance
actually i have two requests , i will start with showing brief topology about my network and start asking the questions .
here is the topology below :
from the topology above , my access is only on R1 which is BGP internet gateway router and R2 is my ISP router.
1- i want to apply Qos on R1 so that a subnet of 32 ips to have gurantee bandwidth of 30M .
assume the subnet is 10.20.30.0/27 that need to be bw gurantee .
2- i want the download traffic by idman or ftp on my Router R1 dont exceed 50 % of my total bw .
i mean that i have 450M bandwith from my isp , & sometimes we have a slow in browsing , so i want to enhance the browsing quality because its more important that downloading files from internet.
here is my two requests above , i dont know how it will work with the precedence of the cache server .
anyway , i will paste my config of router and i will replace my puplic ips with xxx for privacy .
7200Gateway#sh run
Building configuration...
Current configuration : 10149 bytes
upgrade fpd auto
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname 7200Gateway
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 50000
enable secret xxxxxxxxxxxxxx
no aaa new-model
ip source-route
ip wccp 80 redirect-list CACHE80
ip wccp 90 redirect-list CACHE90
ip cef
no ip domain lookup
ip accounting-threshold 4294967295
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
multilink bundle-name authenticated
username xxxxxx password xxxxx
archive
log config
hidekeys
interface GigabitEthernet0/1
description LAN
bandwidth 230000
ip address 10.160.150.2 255.255.255.0
ip wccp 80 redirect in
ip policy route-map CACHE-REDIRECT
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description Cache
bandwidth 150000
ip address x.x.x.x 255.255.255.248
ip wccp redirect exclude in
load-interval 30
duplex auto
speed 1000
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description Internet
bandwidth 230000
ip address x.x.x.x 255.255.255.252
ip wccp 90 redirect in
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
router bgp zzzzzzz
no synchronization
bgp log-neighbor-changes
network xxxx mask xxxxx
network xxxx mask xxxx
network xxxx mask xxxxx
network xxxx mask xxxx
network xxxx mask xxxxx
network xxxx mask xxxx
redistribute connected
redistribute static
neighbor zzzzzzzz remote-as zzzzzzz
neighbor zzzzzzz password zzzzzzz
neighbor zzzzzz route-map Pipo out
no auto-summary
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 xxxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
no ip http server
no ip http secure-server
ip flow-top-talkers
top 200
sort-by bytes
cache-timeout 5000
ip access-list extended bb
permit ip xxxx.xxxx.xx.0 0.0.1.255 any
ip access-list extended CACHE80
permit tcp xxxxxxx any eq www
ip access-list extended CACHE90
permit tcp any xxxxx.0 0.0.0.255
ip access-list extended pipo
permit ip xxxxx xxxxxxx any
permit ip xxxxx xxxxxxx any
ip access-list extended private
permit tcp 172.16.0.0 0.0.255.255 any eq www
permit ip 10.20.30.0 0.0.0.255 any
ip access-list extended telnet
permit ip xxxxxx xxxxxxx.255.255 any log
permit ip xxxx xxxxx 0.0.0.255 any log
ip prefix-list bb seq 5 permit xxxxx
ip prefix-list bbseq 10 permit xxxxxx
logging history size 500
no cdp run
route-map pipo permit 10
match ip address prefix-list pipo1
route-map pipo permit 20
match ip address prefix-list newsubnet
set metric 500
set origin incomplete
set as-path prepend xxxxxxxxx
route-map permit 10
match ip address prefix-list bibo
route-map CACHE-REDIRECT permit 10
match ip address private
set ip next-hop 1vvvvvv
route-map CACHE-REDIRECT permit 20
match ip address bibo e1
set ip next-hop vvvvvv
route-map CACHE-REDIRECT permit 30
match ip address pipo
set ip next-hop vvvvvvvvvv
route-map CACHE-REDIRECT permit 100
snmp-server community xxxxxx RO
control-plane
dial-peer cor custom
line con 0
password xxxxxxxx
logging synchronous
login
stopbits 1
line aux 0
stopbits 1
line vty 0 4
exec-timeout 60 0
password xxxxxxxxxxxxxxxxx
logging synchronous
login local
endHi Vinay,
Please check the program. I have used the replace statement but it is not working.
IF NOT v_sap_bom_rec IS INITIAL.
Spliting the records at '~' delimiter
SPLIT v_sap_bom_rec AT c_del INTO wa_bom_file-model_name
wa_bom_file-product_code
wa_bom_file-description
wa_bom_file-product_type
wa_bom_file-mfg_part_num
wa_bom_file-mfg_part_desc.
REPLACE cl_abap_char_utilities=>horizontal_tab IN wa_bom_file-mfg_part_desc WITH space .
wa_bom_file-status = c_status.
APPEND wa_bom_file TO i_bom_file.
But it is not working.
Please help me..
Thanks
Neelima -
Apply Patches on Oracle Database with Logical Standby Database
Here I am:
I got a primary database with a logical standby database running Oracle 11g. I got two client applications, one is the production site pointing to the primary one, another one is just a backup site pointing to the logical one.Things will only be written into the primary database every mid night and client applications can only query the database but not add, update nor delete.And now, I want to apply the latest patch on both of my databases. I am also the DNS administrator, I can make the name server pointing to the backup site instead of the production one.I want to firstly apply the patch on the logical one, and then the physical one.
I found some reference which explains how to apply patches by adopting "Rolling Upgrade Method". however, I want to avoid doing any "switch over" mentioned in the reference because I can make use of name server. Can I just apply patches as the following way?
1)Stop SQL apply
2)Apply patches on logical standby database
3)let the name server point to the backup site
4)Apply patches on the primary database
5)Start SQL apply
6)Let the name server point back to the production site
Thanks in advance.Pl follow the steps in MOS Doc 437276.1 ( Upgrading Oracle Database with a Logical Standby Database In Place )
HTH
Srini -
Note on applying patches to the file system and database
Dear all,
I am new to Oracle E-business suite. Anyone in the house that can give a note (either a step by step or oracle metalink note) on how to apply patches to a file system or database.
Kind Regards.Hi,
Steps to apply an application patch:
- Stop all application services (keep the database and the database listener up and running)
- Download the patch from Metalink
- Copy the patch file to any directory (i.e. /u04/patches)
- As 'applmgr' do the following:
- Source the environment file
- $ cd /u04/patches
- Type 'unzip <patch_number>.zip'
- cd <patch_number>
- Type 'adpatch'
- When it prompts you to enter the patch driver, type 'u<patch_number>.drv'
Apply the patch on the database tier first then on the application tier.
Do not forget to 'Enable Maintenance Mode' from adadmin before applying the patch. Once you apply the patch successfully, 'Disable Maintenance Mode' from adadmin.
And, always follow the steps in the patch README file.
For database patches, follow the steps in the patch README file and apply the patch using opatch as oracle user.
For more details about applying patches, please refer to:
"Oracle Applications Maintenance Utilities" manual
http://download-uk.oracle.com/docs/cd/B25516_14/current/html/docset.html
How to apply EBS 12i pathces in both Linux and Windows
Re: How to apply EBS 12i pathces in both Linux and Windows
Need to apply patch!
Need to apply patch!
Regards,
Hussein -
How To Install Patch in BI Publisher Server
Hi Experts,
Can any one please guide me how to apply patch in BI Publisher server.
Any reference would be appreciated.
P.S : I have gone through the "read me" file but it is not making much sense to me.
Regards,
AndyWhat patch is this ? PSU/CPU or a upgrade ?
-
Error while applying patches (HRSPs)
Hi,
I have applyed patches in sandbox system. after that server got restarted due to some power outage. i have started database manualy. every thing is up and running. now i am trying to apply the patches in development system which is running in same BOX. now it is getting struct at Addon conflict stage. if i see the ST22 list there i got the dump everytime DBIF_RTAB_SQL_ERROR. in that it is showing that no connectivity to database. i am surpizing that with out database connectivity how the instanses are running? then i have restarted database and listner manualy but there is no use. can somebody please in this issue. Just FYI The same patches i am applying in the different server are working fine.
Thanks in Advance,
Dev.Hi,
Did you use SPAM? What is the status of SPAM? The error could be due partial instalaltion of patches as you lost the power while installation.
Manoj
Maybe you are looking for
-
Ichat 3.0.9 to ichat 5.0.3 connection problems
Hi, situation as follows: Mac A : iMac G4 17" (domed body) running OS 10.4.11 and iChat 3.0.9 with external iSight camera Mac B : iMac G5 20" running 10.6.6 and iChat 5.0.3 When Mac A tries to call Mac B, a window pops up showing the cameras view of
-
How to embed URL of deployed java servlet into Android code
I have deployed my servlet code on cloud which access the database cloud , but when i try to access the URL of deployed application , it asks for my credentials (username and password).... Now that i want to embedd my servlet link on cloud to my andr
-
Reg Creation Position and Otg Unit
Hi Am creating org and positions using FM 'RH_OBJECT_CREATE' and its creating org unit and position ,but when i see in PP01 tcode i can see position very well but for org unit it will show only otype and objid and it not show green arrow
-
hi all, can any one gimme step by step procedure to load data from one cube to another cube in BI7 thanx in advance
-
I want to change the tab page lable dynamically whenver user select the concerned tab page it should be bold,i tried but it seems to me its not possible due to OS. Any body has clue which serve my purspose to just alert the user that you are on this