How to be sure port 10443 is open on vintage airport extreme ( ufo shape, not square)

My Denon 2112 AV reciever is having intermittent internet connect issues. Denon says to be sure port 10443 in my router is open. How do I check this and see if it is open on my vintage (ufo/dome shape) airport extreme?

To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <skip this setting as you will be custom configuring which ports you need opened for the TiVo>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"

Similar Messages

How to make single port fowarding for camera by using airport extreme ???

hi
I have airport extreme model no A1143 (apple)
when I was using linksys ,I have camera
I reserve IP local for camera and then by aplication single port foward I put IP local for camera so I would get for the picture or video
Is any body can help by using apple airport extreme model no A1143
where should I put the IP local for the camera ?which application
thanks
Message was edited by: charlie368

charlie368, Welcome to the discussion area!
Using AirPort Utility you can configure the AirPort Extreme base station (AEBS) to forward the port(s) to the camera. However the camera will need to be assigned a local IP address. The default local IP addresses are in the 10.0.1.x range.
To get to the camera from the internet, you would use the IP address provided by your ISP. This is the one used by the WAN side of the AEBS.

How do I use a seagate external hard drive with airport extreme?

I have a 1tb Seagate external hard drive and I connected it to the USB port at the back of my Airport Extreme. I opened Airport Utility and am now lost. How do I access the hard drive?
(I have a Macbook Pro running os x version 10.8.2)

The external hard drive must be formatted either in Apple's HFS+ or in Microsofts FAT32 in order for it to be recognized. You can format the drive by connecting it to your Mac and bringing up "Disk Utility".

I have a Linksys 10/100 5 port workgroup switch attached to an Airport Extreme. Does anyone know if this setup will work properly?

I have a Linksys 10/100 5 port workgroup switch attached to an Airport Extreme to expand the number of ports. Does anyone know if this setup will work properly?

Sure - just be aware that it will limit you to 100Mb/s internal network speed. If you want to be able to transfer files internally on your network faster, look into a gigabit switch.
Matt

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

How can i connect my Panasonic Viera Link TV with Airport Extreme?

I use the Panasonic adaptor that came with my Blu-ray player. It worked with my Panasonic plasma TV when I used a NetGear router, but I recently changed to an Airport Extreme router and now neither the Blue-ray nor TV will connect. They find my network, but when I enter the password, after waiting a while, I get an error message that the network timed out. My iPad, iPhone, and MacBook Pro and MacAir all connect fine to this router from anywhere in the apartment. I am not using the wrong case when entering the letters of my password. It's exactly the same passsword that I enter on all my devices. Please help me connect the Panasonic TV to the Airport Extreme--I do NOT want to use ethernet. I want to use the wireless connection. Again--it worked fine withe the Netgear router, but does not connect wiht teh Airport Extreme. Thanks!

Checking the specifications of your camera, I see it as a Firewire out .
DV: 4-pin, digital input/output, IEEE 1394 standard (IEEE 1394 is Firewire)
So you should be able to connect it to your Mini via the Firewire 800 port.
You will need a Firewire 400 to Firewire 800 cable because the Firewire on the camera is a 400.
But I couldn't fine any info that confirmed this model is compatible with iMovie if this is what you plan to use for editing.
There is a work around but it is not very easy.
Simplest way to import your videos is still Elgato video capture, but it will not give you the same quality as DV

How do I prevent other Mac users from changing my Airport Extreme Network Name and Password within the Airport Utility?

How do I prevent other Mac users from changing my Airport Extreme Network Name and Password within the Airport Utility? My company is using an Airport Extreme in our office now and I want to prevent other employees from messing with the network/settings. Is there a way to place a password on the settings to allow only the admin to access the network name and password?

Hi - you have will have to change the device passwords on all the base stations and then don't give them to anyone except the administrators and tell them not to save them on their computers that use the older versions of the Airport Utility - for the newer versions like the mobile apps, as soon as you enter the pasword it is saved and is visible in the advanced pane along with the network password - so if anyone gets a hold of your iPad or iPhone, they can edit the whole network - I have this same issue with my networks in the office and it is inconvenient but doable - I hope this helps

How can i sync ipad1/iphone4 with itunes wirelessly using airport extreme network

how can i sync ipad1/iphone4 with itunes wirelessly using airport extreme network

Hi,
This is currently not supported by iOS for any devices. Rumour is that iOS 5 will finally add this function, until then I'm afraid you are stuck with the good old cable.
Jamie

Airport extreme software will not install on vista, how can i still configure the router?

airport extreme software will not install on vista, how can i still configure the router? Trying to help someone with vista get an airpot extreme configured. 10.0.1.1 does not work, the software will not install correctly on their vista machine. How can I get into the base tation and lock it down?

Hi - Vista can be tricky - I need more info to see if I can be of some help - first, is the Vista machine a desktop or a laptop and is it fully up to date with Windows Update (sp2 or higher)? - next, are you trying to install Airport Utility version 5.5.3 which is the correct one for Vista? - and finally, what do you mean "it will not install" - what kind of error messages or evidence are you getting?

How to open Nat on airport extreme

Hello i just got a new airport extreme trying to connect xbox it says i need to open nat. my computer is running vista i have a ipad and iphone 5s please help

Xbox uses upnp.. think vhs..
Apple routers use NAT-PMP.. think betamax..
When xbox says please open the following ports for me.. apple router blows a rasberry at it.. and says tough.. you are not apple.. I don't have to do what you say.
Same for your vista computer.
iOS devices should be ok.
You will need to manually port forward. Good luck with that.
http://support.xbox.com/en-AU/xbox-360/networking/network-ports-used-xbox-live
Tesserax is the guru here and he often answers these queries so refer to one of his posts for more details.
AirPort Extreme and xbox 360
https://discussions.apple.com/thread/5385065?tstart=0
The latest Xbox one should just add a couple of ports but will be about the same.

How can I get two hard drives connected to the Airport Extreme. There's only 1 USB port.

I believe I want to use TWO USB Hard Drives with my Airport Extreme, but it seems there is only 1 USB port.
I am currently using that USB port for my backup external hard drive (works with Time Machine). But now I have decided I want a common hard drive for music, photos, etc. for the two Macs in my home to share. I read that you do that via the same port.
What should I do? Is there a way to use 2 hard drives - a common shared and one for time machine?
Please advise and thank you!

singer777 wrote:
I believe I want to use TWO USB Hard Drives with my Airport Extreme, but it seems there is only 1 USB port.
Use a (powered) USB hub.
I am currently using that USB port for my backup external hard drive (works with Time Machine).
I hate to have to tell you this, but backing-up that way is unreliable and not supported by Apple. See: Using Time Machine with an Airport Extreme Air Disk.

How do I find out who is connected to my airport extreme?

I have a motorola WPS870G wireless printserver that has an old HP LJ4 attached via parallel. I had a netgear router and all was good. I had it set up so that the router always assigned the same IP address to the print-server, and then I had my G4 set up to print to that IP address - then shared the printer to my MBP along with the other two printers attached to the G4 which is really now just a server in the closet. Anyway, when I switched over, I can't figure out how to find what IP address is being assigned to the printserver now nor how to make sure it's fixed. I've logged onto the printserver and set it to ask for the same IP address every time from the extreme and it does show that it's connected (based on the lights that are lit). I should also share that I first had to change the network SSID and the WEP pw to match the new network. I first tested to make sure it disconnected from the old network, then made sure the lights came back on for the new network. But now I cant figure out what IP address it's connected to. Ultimately, I need to be able to hard code that into the shared printer on the G4 to get everything back in working order. Any suggestions on how to get this printer working?
Thanks.

I'm not sure if this is what you're looking for, but you can find out who's connected by using something like Airport Monitor Utility (3rd party software) or you can use Apple's Airport Utility. Apple's Utility will also let you change settings if you don't like what you find, so we'll use that for this little example.. Please read through this whole thing before you attempt it so you know what to expect at each part and how it relates to later information. Note this will only work if the parallel print-server is connected directly to the AirPort router by wireless or wired connections. If there are any in-between routers, these directions may fail to help you and you should consider reconnecting the print-server directly to the AirPort base station.
First, write down the MAC address of the print server (or ANY other device) you need to configure for a "static" address. In this case, I mean static address not by the sense that we are not using DHCP to assign it, but in the sense that ultimately it doesn't change so your Macs and other computers/devices can always find it on the network.
* If you can't find the MAC address of the print-server or other device in question, then the only other way to go about assigning it a non-changing address will require that you can access that devices internal network setup configurations (some helpful directions on that at the bottom of this text) and set the device's DHCP Client ID to something that you will set the Airport to look for later when it assigns the print-server its connection address. MAC Address is probably easiest to use because you may be able to find the MAC Address of the device on a sticker on its case. If you can't see a MAC Address listed on the device or it has been altered through settings and you can't access the device's setup configuration pages over the network to find its current Mac Address, you may still be able to figure it's MAC Address out by following the monitoring directions immediately below.
Using Airport Utility v5.3.2, here are directions for monitoring and assigning addresses, etc:
* How to see who's connected....
1. Open Airport Utility.app
2. Select the appropriate Airport base station.
3. Click "Manual Setup" at the bottom.
It will read settings for a moment, then you should see info on the station itself. If not, click the Airport logo on the left side of the top bar of icons to take you back to this top menu page and click the "Summary" sub-tab on the left below it.
NOTE: A lot of people don't realize the fact that this "info" is actually a menu with hidden shortcuts that lead to a lot of advanced useful features that otherwise you might take a while to hunt down navigating icons and tabs above. You have to actually mouse over each line to figure that out.
4. To find out who's connected, mouse-over the entry that says Wireless Clients until it has a right-pointing arrow in a circle appear to alert you that it's now a link. Clicking "Wireless Clients" will be a shortcut that saves you a lot of time and clicking that would equate to clicking the obvious controls above in the order: icon "Advanced", then tab "Logging", then page link "Logs and Statistics" then tab "Wireless Clients".
Note: This info is not a static display, but an active charting of who's connected, at what speeds, with what signal to noise ratios. It updates very quickly.
5. From here, you can click the "DHCP Clients" tab to see all the devices connected to this basestation by either wireless or wired connections and their relevant MAC addresses, etc. This page unfortunately has no direct quickly like its neighboring tab for Wireless clients, but at least you have a shortcut now to get you to this pages nearest neighboring tab which does save some time.
Note: This info will be helpful to figure out what's going on with your print-server or other routers/devices if you know their MAC addresses. You can find the MAC address on most devices on a sticker somewhere on the bottom or back side of the device if you can't pull up a configuration page on it to tell you. Some devices can have their MAC addresses reprogrammed through their configuration pages. Be aware of that possibility if you can't find the expected MAC address connected in this list. If you can't figure out which MAC address is your print-server, disconnect it from AirPort and see that a device disappears from the list. Then reconnect it and the device that is added to the list again is the MAC address you are looking for. Write this down for the next section. If it doesn't appear in this list, then we have a real problem with the connection like possibly the print-server device's internal networking settings are messed up and need to be reset to defaults. There is some info on how to go about that at the bottom of this text.
Now, on to forcing a DHCP device connected to AirPort routers to always use a particular address:
Once you have an idea what the MAC address is of the device you want to force to use a static address, you can go about it two ways. Either you assign it an address permanently in its own configuration page (if accessible) after turning off its DHCP setting to static, or you can use its DHCP setting to set the address with the Airport Router automatically to the same address every time it reconnects to the network or is turned back on, etc. The steps with Airport need to start the same way in either case.
1. Same as before, if you haven't already, open Airport Utility, select router, click "Manual setup"
2. Click the "Internet" icon at the top. Then click the DHCP subtab.
3. To keep other devices from "Stepping on" your address that you want to assign permanently to the printer or other device, make sure the static address you choose is outside of the range of DHCP addresses setup on this page. If not, other devices could take the address away from time to time and it will cause you headaches.
Once that's set so you have an address protected from other devices getting assigned to via DHCP by limiting the DHCP address range not to include it, here's where you must choose which route to use to assign the address. You can either assign it in the printer's web-reachable configuration page (if you can figure out how to get to it and have the passwords, etc to do it, and its configuration is capable of accepting static addressing etc.. ) OR you can assign it directly from Airport's configuration (recommended). This is how to do it in Airport Utility from the DHCP controls we just opened:
1. Under the "DHCP Reservations" section, we want to click the add "+" button to set up your printer or other device for a static (but assigned) address that won't change..
2. Enter a description like "printer" or "print server" or what have you.
3. Select reservation by "MAC Address", then click "OK".
NOTE: You can use the reservation by "DHCP Client ID" to set this up as well, IF the device has a unique Client ID set in its configuration settings. I don't recommend doing so for two reasons. MAC Addresses are more hardware based, and thus, a more stable method of identification that isn't likely to change and cause you grief later. DHCP Client IDs are software-set and more subject to get wiped out if the device is reset than its MAC address as well there is the potential for two devices to be set to the same DHCP Client ID if one isn't careful, which would also cause confusion for AirPort. Most networking devices won't let you "fake" their MAC address using software settings, so MAC address can be considered the most stable and desirable method of identifying a non-computer on your network. Computers are the most likely culprits for spoofing different MAC addresses through software, so likely you don't have to worry about that with your print-server, although it's dependent on the manufacturer and what they gave it the capability to do.
4. Now here you enter the MAC address (or DHCP Client ID if so directed) of the print-server or other device you want to permanently assign the address you've chosen.
5. Lastly, enter the static IP address you want it to take on each time it is reset and requests and address again from AirPort and click done. This address will always be held available and assigned every time by Airport each time the device with the MAC address you gave it asks for a DHCP address assignment. Thus, while the device thinks its being assigned dynamic addresses, its just using the DHCP process to be assigned the same address every time by AirPort..
6. Save the changes you just made to your Airport configurations for DHCP assignments and reservations and then after Airport restarts, power-cycle your printer or other device you just setup by matching MAC address in Airport Utility and it should be assigned the new address you just specified.
7. AIRPORT TEST: Go back to the first directions in this piece to check the DHCP device connections. You should see the Mac address of the printer show up with the correctly assigned "static" IP address now in this list. If you don't, then perhaps the printer or other device assigned isn't set up for accepting an address by DHCP in its own settings. Usually this is a default behavior for any device connected to a network. If you can't open the configuration settings, at your option, you may find a pin-hole reset switch on the device you can use to reboot it with original hardware configuration settings that probably are set to DHCP.
8. Don't forget to go change your print-server settings in System Preferences of all Macs connected (and printer settings of any PCs). Your Mac needs to know the print-server's new 'permanently' assigned address in order to find it.. Be sure to save the changes..
** Be careful that you know what you are doing if you have a device that doesn't want to cooperate the way you think it should with your AirPort router. If you can't access the devices internal configuration settings in your web browser by typing its current IP address in the URL format http://.xxx.xxx.xxx.xxx, you should lookup the device manufacturer's website and search it for their support info on the device for its setup, default user-name/password and default network configuration and IP address settings to understand why you are still having trouble before you resort to resetting it by hardware reset switch. Hardware resets can sometimes have very bad results. Avoid this until the software configuration route can't be achieved by any method you try.
If you have any PCs that need to find the print-server and that setup proves to be too difficult, sometimes it helps to install Apple's Bonjour software for PCs (running Windows 2000, XP, or Vista only).... It will try to automatically locate any printers or print-servers on your network, but also makes the set-up a lot easier in general in most cases...
I hope that helps.

How do I use more than one USB device with Airport Extreme?

I would like to plug a shared hard drive into my new airport extreme and still be able to plug in a shared printer as well. How am I supposed to do this with only one USB port. Do I use a USB hub???
Is it possible to connect a hard drive using one of the ethernet ports?

To use multiple USB devices you would use a powered USB hub.
You can connect a hard drive to one of the Ethernet ports providing the hard drive is a NAS and supports Ethernet connections. In that situation the NAS hard drive is just like any other Ethernet client and the AirPort Extreme base station (AEBS) does not handle the file sharing services. The drive itself would provide the file sharing services.

How can I have the external HD connected to my Airport Extreme show up on Windows 7 and 8.1?

So, I have an Airport Extreme which works flawlessly. I have a 1 TB external HD connected to it. On my Maccbook Pro and a windows 7 laptop, I can view the HD as "Z". For some reason, on another Windows 7 and Windows 8.1 Laptop, it is not showing up under my computer. Any advice? THANKS!!

You can share files with iOS devices by using filebrowser or other file app.
To play movies on the iOS device though you would need a player that is outside of itunes.. because itunes will not play from the router.. it has no media extensions.. neither does the TC which merely adds an internal disk but is otherwise identical.
So look up how to play movies with a player on the iOS.. there is several available I am sure.
http://www.pcadvisor.co.uk/how-to/apple/3512138/how-put-films-on-ipad/
BUT itunes depends on a computer running in the network.. so storing the itunes library on the AE is useless.. and will slow the network down no end. It is much better to put files where they can be accessed.. ie directly on the computer.

How to setup a static ip address and DNS on airport extreme using the iOS Airport Utility?

I am at a location that only has wired ethernet. The ethernet connection has a specific Static IP address, subnet, gateway, and DNS setting. I cannot seem to find how to enter DNS settings using the Apple Utility on an iPad. HELP!!!

First, I am assuming that you are trying to administer your AirPort base station for a static IP address using the iOS version of the AirPort Utility ... correct?
If so, then to do so:
Start the AirPort Utility app on the iPad
Select your base station.
Select Edit
Select Internet Connection
Select Static
Enter the appropriate IP address information
Select Done
Sorry, it does not appear that direct input for DNS IP addresses is an available option with this version of the iOS AirPort Utility app. Not sure why this was not included.

How to be sure port 10443 is open on vintage airport extreme ( ufo shape, not square)

Similar Messages

Maybe you are looking for