How to block specific incoming calls

CCM 4.1(3)sr2
I am currently able to block specific calling numbers from PSTN with translation rules like this in my h323 gateway:
voice translation-rule 10
rule 1 reject /323xxx9650/
rule 2 reject /323xxx9580/
Then I use it with a call-block translation profile on the dial peer like this:
dial-peer voice 1 pots
call-block translation-profile incoming call_block_profile
destination-pattern 9T
progress_ind setup enable 3
incoming called-number .T
direct-inward-dial
port 2/0:23
Now I want to convert to MGCP and find that doing this same thing in Callmanager is [to me] less than obvious. Any thoughts?

Stick with H323 if you are wanting to do call control for PSTN calls, because, with MGCP, it is doable from CallManager using a combination of Route Patterns / Translation Patterns, but it is MUCH more convoluted than what you currently have established with your translation rules, which look pretty clean to me. If there is no GOOD reason to change, leave it alone....

Similar Messages

How to block private incoming calls on iphone4, how to block private incoming calls on iphone4

how to block private incoming calls on my i phone4

It might not be any use to your situation but I find adding a default ringtone to those unwanted callers helps me decide whether or not to pick up the phone.
If it's cold callers that trouble you I would defintely reccomend this option.
If they know your not answering they will (although it may take some time) leave you alone.

How could I block the incoming calls to a specific number

How could I block the incoming calls and text messages to a specific number?

Contact your cell service provider.
Message was edited by: deggie

Can you block a incoming call on iPhone 4s

Can you block a incoming call on iPhone 4s?

Call blocking is a carrier feature. In the U.S., most major carriers offer blocking features. Give yours a call.

How do I extend incoming call duration before voicemail activates ?

How do I extend incoming call duration before voicemail activates ?

I had this problem and for 12 months no one could tell me how to fix it.
Finally a young kid told me. Get onto your carrier web site, in this case Telstra in Australia,
and you will search for ringing or similar and there should be instructions how to do it. It worked!!!
good luck

How can i hide incoming calls from showing on my screen

How can I stop incoming calls from showing on my home screen?

If you just don't want to see the call notification on your home screen go to Settings, Notification, Phone and turn Notification Center to Off. Or you can simply select None and calls will be listed in the Notification center but you won't see a banner / alert on the home screen.
This also eliminates the Caller ID from being displayed before you answer the call.

HT1688 when traveling foreign countries, want to block the incoming calls for my iphone. 4

When traveling foreign countries,block the incoming calls. What is best way without turn off power? Thanks. camano8218

Put it in airplane mode (you can then enable wi-fi if you wish to use it).

How to block an incoming iMessage?

Does anyone know how to block an incoming iMessage? Verizon can't block because iMessage uses data, it's not a regular text message. Thx

You can Turn Off iMessages..Turn Of Notifications & Sounds..that way only You kno its there..
Trace the Number & Report it to the Police if it's that bad...

How do I retrieve incoming calls for the past one month?

How do I retrieve incoming calls for the past one month?

You can open the phone app and tap on recents at the bottom of the screen that's about it

Blackberry Passport is blocking some incoming calls

Hi,
My BB Passport is blocking all incoming calls if I don't have the number saved in my contact list. If there any way to turn off this option? I've contacted my service provider, and there is no restriction on my phone line. In fact, the service has been restarted twice.
Thanks,
Cesar
Solved!
Go to Solution.

Hi @cvelasqu
Let me know if this KB helps!
KB36391 Unable to receive calls or text messages from phone numbers not stored within a contact in t...
Did someone help you? Click Like! Did a post solve your issue? Click Accept as Solution!
Follow me on Twitter or Google+ and subscribe to the Inside BlackBerry Help Blog

How do I reject incoming calls on Ios7 when locked? Power button on top right does not work.

How do I reject incoming calls on Ios7 when locked? Power button on top right does not work.

I am also facing the same issues. Sometime i get an option to reject call and sometime i won't .
Tried all the basic troubleshooting i could from my end but nogo. Also tried complete reset by loosing data still the same results. Any suggestions and fix, Apple ???

How do i bar incomming calls when roaming but still receive messages

How do i bar incomming calls when roaming but still receive messages

I had this facility on my nokia phone. So iphone cant. Thanks for info

How to know your incoming call is on call conference

How to know your incoming call is on call conference

Hi amit,
Thanks for the reply.
But i already mentioned that my users cann't search using tables.
I want to know that whether any tcode is there to display the all incoming invoices created including with ALE-idoc also.
Thanks,
Vamshi.

How can i reject incoming calls in lock screen , without using ON/OFF key ??? (in iOS 7.0.2)

how can i reject incoming calls in lock screen , without using ON/OFF key ??? (in iOS 7.0.2)

You can't. Either tap the Sleep/Wake button or just let the call to continue to ring.

CME\7960 running SIP firmware - How do i setup incoming calls? - Can anyone help please?

Hi Guys,
I have a SIP trunk setup with a 2811 running CME version 7. I can make outbound calls ok but having issues getting the incoming calls working, i have 1 number on my SIP trunk and that is 01133501788 and i want that to ring my Cisco 7960 which is running SIP firmware not SCCP. I have included by config for anyone who can help me, i just want the incoming call to work.
Many Thanks.
Matthew.
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
   network 10.10.10.0 255.255.255.0
   default-router 10.10.10.1
   dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 188.92.232.50 188.92.232.100
   option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
bind control source-interface FastEthernet0/1.20
bind media source-interface FastEthernet0/1.20
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0008072514198272
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^9$.*$/ /\1/
voice translation-rule 2
rule 1 /^6...$/ /4143*002/
voice translation-profile DiscardDigit9
translate calling 2
translate called 1
voice translation-profile IncomingSIP
translate calling 1133501788
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing DiscardDigit9
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#

You my friend are a star! worked straight away, many thanks. Just one more thing, when i make an outgoing call, it always appears as "blocked" on my phone, my sip trunk is set to allow CME to alter outgoing CLI's how would i program the outgoing CLI to 01133501788 also?
The new working config is below with your suggestion, which works!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
   network 10.10.10.0 255.255.255.0
   default-router 10.10.10.1
   dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 188.92.232.50 188.92.232.100
   option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0015244443466064
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^6...$/ /4143*002/
voice translation-rule 3
rule 1 /^01133501788$/ /6999/
rule 2 /^1133501788$/ /6999/
voice translation-profile IncomingSIP
translate called 3
voice translation-profile Translatetrunk
translate calling 1
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target sip-server
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing Translatetrunk
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 17 2013 14:35:13
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#

How to block specific incoming calls

Similar Messages

Maybe you are looking for