How to bridge a linksys cisco E1200 series router?
I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox
purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App
Similar Messages
-
Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
IP_ADDRESS: 10.0.0.3
IP_SUBNET_MASK: 255.0.0.0
DEFAULT_GATEWAY: 10.0.0.1
TFTP_SERVER: 10.0.0.2
TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
TFTP_VERBOSE: Progress
TFTP_RETRY_COUNT: 18
TFTP_TIMEOUT: 7200
TFTP_CHECKSUM: No
TFTP_MACADDR: 30:37:a6:49:35:a8
FE_PORT: Fast Ethernet 0
FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 > " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
TFTP_MACADDR: The MAC address for this unit
FE_PORT: 0= (default), 1
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
5=Auto (default)
TFTP_DESTINATION: The flash destination device for the file
flash:(default), usbflash0:, usbflash1:
Command line options:
-h: this help screen
-r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
IP_ADDRESS: 10.0.0.3
IP_SUBNET_MASK: 255.0.0.0
DEFAULT_GATEWAY: 10.0.0.1
TFTP_SERVER: 10.0.0.2
TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
TFTP_VERBOSE: Progress
TFTP_RETRY_COUNT: 18
TFTP_TIMEOUT: 7200
TFTP_CHECKSUM: No
TFTP_MACADDR: 30:37:a6:49:35:a8
FE_PORT: Fast Ethernet 0
FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick -
Configuring New Interface and NAT on Cisco 1900 Series Router.
Hello Cisco Team,
am asking for advise on how to how setup NAT rules and overload on my 2nd interface on my cisco 1900 series router,am not sure where am getting it wrong.
my router has 2 interface, interface one has IP address 10.5.5.5X and plugs into my ASA firwall and into my switch and works just fine.
i have just configured my second Interface with a new IP 172.16.0.X- i want to NAT my new IP address to our public IP address which is 41.77.X.X
my configuration so far are as follows.
GigabitEthernet0/0 172.16.0.X YES manual up up - Not working
GigabitEthernet0/1 10.5.5.X YES NVRAM up up- this works fine
GigabitEthernet0/0/0 41.77.X.X YES NVRAM up upHello Jon,
Thanks for your feedback, my router configuration are as follows.
interface GigabitEthernet0/0
description WL2504
ip address 172.16.0.2 255.255.254.0
duplex auto
speed auto
interface GigabitEthernet0/1
description WAN
ip address 10.55.55.2 255.255.255.252
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/0/0
description LINK TO CLT INTERNET
ip address 41.X.X.130 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex full
speed 100
media-type sfp
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0/0 overload
ip route 0.0.0.0 0.0.0.0 41.X.X.129
ip route 41.X.X.136 255.255.255.248 10.55.55.1
ip route 192.168.0.0 255.255.255.0 10.55.55.1
access-list 1 permit 10.55.55.0 0.0.0.255
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 1 permit 192.168.1.0 0.0.0.255
from the router interface interface GigabitEthernet0/0- I will connect it to my wireless Controller WL 2504 -
License on the Cisco 3900 Series router.
I am trying to understand what does the "data" license exactly do on the Cisco 3900 series router. What I understood is that the data license supports "MPLS.ATM. Multiprotocol support".
Question is is a do not have this license will I not be able to run BGP, EIGRP and terminate service provider links?
Technology Package License Information for Module:'c3900e'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
NtwkEss None None None
CollabPro None None None
Configuration register is 0x2102
Thanks,
NikI think WAAS express is one of the technologies you will lose out on. Amongst other advanced features. See link below.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/software-activation-on-integrated-services-routers-isr/white_paper_c11_556985.html
EDIT: And performance routing. -
NetConfig issue wrt Cisco 3900 Series Router
Hi Cisco;
I can't able to configure my Cisco 3900 series Router via NetConfig tool. While I am able to Configure all other Routers (7600, & 2800) and Switchs (6500, 3700, 3560). I can accessable 3900 Series Router via Inventory Collection, Sync Archieve, Campus Manager, DFM and etc.
I have Cisco LMS 3.2 with RME 4.3 & using SNMPV3.
Thanks for your support.
Best regards;
Shoaib AhmedHi Clarke;
Please find the requested Screen Shot.
Actully my problem is that, I can't configure my Cisco 3945 Routers (Shows not applicable devices) via NetConfig tool. I can use other tools like Sync archieve and etc is working fine for these 3945 routers.
Best regards;
Shoaib Ahmed -
Question about setting up rdp using a cisco 800 series router
HI there,
I am currently in school for networking. One co-op placement I went too handed me a cisco 800 series router to practice my routing skills on. I am trying to setup RDP so I can access my server from outside my internal network. I ran this following acl command to do it.
ip nat inside source static tcp server IP address port# cable modem IP port # extendable.
My question here is, my cable modem will occasionally hand out a different IP since it has DCHP. I cannot turn DHCP off in my cable modem. So is there a way I can set this up to use a dynamic IP from my modem so I alwasy have access to it or every time my modem changes the IP address do I have to go in and modify this acl?Configure DDNS ( Dynamic DNS ) on the router. For this you need to register with a DDNS provider. Go to
http://www.no-ip.com/ . they provide free reliable service.
With DDNS, Once your router gets a DHCP address from your ISP , it will dynamically update the DNS name record. For example if you register you routers name as, "myrouter.no-ip.org", from there onwards whatever the IP your router gets, you can refer to that by this name.
So do as what Paolo said regarding using interface instead of ip, and register with the DDNS and you are good to go..
Hope this helps
Please rate this post if helpful..
Thanks
Shamal -
IOs for cisco 1900 series router
Hi,
Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
Cisco IOS System Timers Remote Overflow (CSCei61732)
Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
Cisco IOS Telnet Service DoS (CSCef46191)
Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
Regards,
BalaHi,
The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
Regards,
A.Bala
leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
>Balakrishnan Appavu,
>
>A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
>
>https://supportforums.cisco.com/message/3277195#3277195
>
>Author : leolaohoo
>Profile : https://supportforums.cisco.com/people/leolaohoo
>
>Message: -
How to move a standalone Cisco C series to UCS managed service profile without losing data?
Hi,
We currently have a standalone cisco C series server with Windows 2012 installed on the local disks. We need to move this server to Cisco UCS managed with a service profile but cannot lose the existing data and OS boot method.
Does anyone know how to do this?
ThanksHi Adrian,
To be able to accomplish this set the local disk policy to "Any Configuration" this way UCSM won't overwrite the current raid configuration on the server.
See link below
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-1/b_UCSM_GUI_Configuration_Guide_2_1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_011110.html#task_897FABF194524BDF8C0EF72E755972F0
Let it me know if this helps -
Cisco 2600 series router and cable modems
Hi everyone, I am just about to get started preparing for my CCNA... I am looking to pick up some used Cisco 2600 series routers to set up a home lab. I am wondering if it is possible to connect a cable modem directly to a 2600 series router? If so, do I need a certain type of WIC? I want to go from my cable modem, to a router, to my switch. Thanks in advance!
Hi,
Yes you can, using the Ethernet port on the cable modem, you can connect the cable modem to the router 2600, and the 2600 comes with builtin ethernet or fastethernet (according to your platform).
HTH,
Mohammed Mahmoud. -
Creating VLAN on our Cisco 300 series router
I am wanting to create separate VLANs on our Cisco 300 series switches, but I am struggling to find any decent examples out there.
Our basic infrastructure is
Router with
192.168.1.1 VLAN1
192.168.2.1 VLAN2
The switch is set up on ports 2345 for VLAN2
Port 1 is attached to the router on VLAN1 and VLAN2 assigned.
My problems seem to be that I really not sure what settings I should be using for each the ports to get this to work correctlyHi,
Hope below link will have the information which you are looking for.
https://supportforums.cisco.com/document/140341/vlan-configuration-articles-sx200300-series-managed-switches
If you are looking for only vlan creation then below link will help.
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=80
According to your above description you have connected the router to port 1 of switch and you have configured it as vlan 1...Should this port be trunk???
Regards
Najaf -
Linksys Cisco EA6400 - Passphrase/router password
I'm trying to find the password for this screen, seen after typing my remote ip address "192.168.1.1", in order to access my router settings.
As you probably already know, I don't know what it is. I've tried the default passwords I could find on some portforward sites, which are "admin" and "tivonpw", along with "default", "password", "[blank]", and every number or letter on the back and front of my physical router. I've also tried many passwords me or my dad might have set it as, but nothing. On multiple occasions, I've tried hard reseting my router and re-typing all of these passwords, first holding down the reset button for 10 seconds, then 30, a minute, and finally two minutes. I also tried calling a support site, but they said my warranty ran out and that I'd need to pay for their advice, which I chose not to.
Things like these have happened enough to where I've stopped becoming frustrated with them, but the help would still be much appreciated.
Thanks.
P.S. A curious thing I noted; this router doesn't seem to have a username?@Baximus
There’s no way to retrieve the router password once you change it from the default password admin.
If you forgot your router password, you can perform a hardware reset to restore your router to factory default settings. Just press and hold the Reset button on the back panel of the Linksys Smart Wi-Fi Router for about 10 seconds then release.
Once done, you may run the Linksys Smart Wi-Fi setup wizard or manually set it up. It should prompt you to update your router and wireless password. Make sure to type the password correctly since it’s case sensitive. -
Linksys Cisco E1200: Session Failed
Whenever I log in to the 192.168.1.1 page of the router to reboot it, it always ends in its log in page with an error, "Session Failed" below the username and password fields. I know my router password and username but why does it always appears. Please help, thank you so much!
Try isolating this matter by using other browsers or computers. Have you tried doing a powercycle? Simply unplug the power cord at the back of the router for 10-15 seconds. If that won’t work, updating the router’s firmware may correct this. Make sure that you are using a computer that is hardwired to the router to avoid any trouble. Use this link to know if you have an updated firmware: http://support.linksys.com/en-us/support/routers/E1200
This link will also guide you on how to properly update the router’s firmware:
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=e9c2361ee7974d75913e61386a712188_4030.xml&pid=80&r...
Help, learn and share -
How do I monitor a Cisco 1700 Series T1 Serial Port.
I have a Cisco 1721 Router and I am looking to monitor it for hourly statistics to find max and min speeds. How would I go about doing this? I know if I do a show interfaces it shows me all the data since the last time the counters were reset. Thanks for any help.
Chad
Diversified Telecom.http://www.paessler.com/
There are many others. -
Linksys n300 e1200 wireless router
I set-up the router on a computer I no longer have. How do I download the software to my new computer without going through set up again? I also need to recover the guest access which was accidently deleted. Thank you
If you really want to take full advantage of the Linksys Connect Software, you need to manually download it directly from the Linksys site, but you may need to set up the router from scratch. I suggest you use the router’s web-based setup page instead, you’ll be able to manage the router and configure the Guest access without setting it up again.
-
How to reconfigure my Linksys EA2700 wi fi router
I made the mistake of resetting my router (EA2700) when it was down and now I need to reconfigure it. Can anyone help me or do I need to pay tech support at Linksys?
ThanksI recommend that you phone contact your regional Linksys support office and ask for help and information...
Maybe you are looking for
-
How to provide value to a User Defined field thru java code
I am using OIM 11.1.1.5. I have a user defined field called Unique-Customer-Number. This field need to be pre-populated during user creation (using OIM Web UI) and the value comes from a java code. Can any of you tell me the high level steps to imple
-
Install OS X Lion + go to factory settings
Hi. I have an iMac with OS X Snow Leopard. I am going to give it away, but want to give a clean manchine, with OS X Lion Installed. If I update the OS X to Lion, it does not give me the option to restart to factory settings (I have done this in anoth
-
How can I edit several lines to cut or replace one word
I am trying to import a CD of an opera. When I put my CD in the reader, I get this (screen copy): I wish to erase all the ocurrences of "Wagner: Parsifal - Act 1:" and keep the rest of the line (the part written in German). How can I do this in one p
-
Workflow Notification status coming canceled by default
Hi, I have a process in my workflow which sends notifications after a wait node (time set to 1 minute at the moment). There is a loop before the wait node which has a value three. So effectively my process sends three notifications after waiting for
-
Modify Transition element in work flow using for and not attributes to restrict access
Hi, I have TFS 2013 for my premises and I am working on changing the work flow for TFS work item. I have created a work item as per requirement and it has 3 states Active, In Review and Closed in work flow. When developer creates a work item it is in