How to change active partition?

Hi experts,
I have disk D which contains OS windows 7 and not in active, but my another disk E is in active with 100% free space.so, how can i change active partition from E to D ? please help me

Hi,
Hope the following two links can help you better under a active partition
http://windows.microsoft.com/en-in/windows/mark-partition-active#1TC=windows-7
http://support.microsoft.com/kb/228004
Yolanda Zhu
TechNet Community Support

Similar Messages

Change active Partition in Solaris 10

I have installed Solaris10 and after Windows Xp, the boot loader disappear. The system Startup always by Windows Xp. I have installed Partion manager and I change Active partition to Solaris 10, Know the system Statup always by Solaris 10. Please tell me how I change active partition in Solaris (to set Windows XP active partition again ). Could I use fdisk ? and how?

1.Change the bios settings to boot from CD
2. Insert the Solaris Software CD 1
3. The procedures for installation starts , when it asks for the type of installation ie Interactive , jumpstart etc.
4. At this prompt type " b cdrom -s "
5. This will give you a root prompt
6. mount the disk root partition onto a temp mount point on cd
mount /dev/dsk/c0d0s0 /a
7. cd /a
8 . Run the format command
9 . Choose fdisk
10 . Follow prompts to make the WinXP the active partition
11. Save changes
12 . Reboot

How to change the PARTITION(P#) is replace of PYYMMDD format

hi
hi everybody, i am developing the appl is used to jsp and oracle.. i need to change # is replace of YYMMDD format in oracle.. i want to display the partition wise data (like p070220) based on the query..
how can you change the query (p#, p070220)....
pls find the above code..
Table Names(1): select * from imis_p3_report
Fields: mis_rep_id, mis_rep_name, query_description
EX: LPP0159,Deativations thru 152 Short code, SELECT
TO_CHAR(CALL_DATETIME,'DD-MON-YYYY') DEACTIVE_DATE, TIME, SUBSTR(CV1,3,10) MSISDN,SUBSTR(CV2,3,10) DEALER_NUMBER,CV3 PRODUCT_CODE,CV4 SYS_STATE, TO_CHAR(TO_DATE(CV5,'YYYYMMDD'),'DD-MON-YYYY') CREATE_DT,CV6 SERVSP_ID,CV7 DEALER_CODE,CV8 ZONE_DEALER FROM DAILY_IN_DUMP PARTITION(P#) WHERE
Upper(Nodelabel)='ID_DEACTIVATION' 2) select * from imis_p3_controls Fields:mis_rep_id, condition_id, control_type, control_label, control_content, default_value
EX: LPP0159, 1, DTP, FORDATE
COntrol_types like DTP, COMBOBOX, LISTBOX, RADIO
3) select * from imis_p3_conditions
Fields: mis_rep_id, control_id, condition_id, query
ex: LLP0159, 4, 2, select
TO_CHAR(TO_DATE('#','DD/MM/YYYY'),'YYMMDD') DT from dual
Condtion_id: 0,1,2,3,4,5..
i want to change the PARTITION(P#) replace to p070220 format
please help me....
Kalyani

Hi there Luke. Thanks for the answer but it has bred a new problem as good as it was. I've shrunk the second volume (E) down to 20GB exactly, however there is now around 53gb of unallocated space. When I right click on the C partition the option for extending is greyed out and it wont let me allocate the 53gb to it.
Any ideas on why this might be?
Wish I knew more about computers! :(

How to change active ascontrol to non-active

I have two 10.1.3.2 instances with each an active ascontrol. Now I want to add them to a cluster, where a discovery server with an active ascontrol is already present (we do not use multicast, but specify the discovery server for each opmn). This means that the ascontrol should be made inactive for the two instances.
My question is: Is it enough to specify start="false" for ascontrol in server.xml, or do I have to make more changes?

Hi,
Hope the following two links can help you better under a active partition
http://windows.microsoft.com/en-in/windows/mark-partition-active#1TC=windows-7
http://support.microsoft.com/kb/228004
Yolanda Zhu
TechNet Community Support

How to change activity number screen attribute

Dear :
Can I change activity number field to "display" attribute? I find all PS config, but can not change screen attribute only for "activity number" field.

Hi Jennifer,
Please follow the steps given below:
1. Using transaction OK02 create a user profile, preferably by copying from an existing profile
2. Now go in for detailed screen of the created user profile
3.Enter status number (you can number them as 1,2,3..),status in short form (like "PROD' for "under production"),
3.Now select the status created by clicking on the left side and click "object types" at the top. Among the objects listed select "Network Header & Activity"
4.Go back to the detailed screen and double click the status. Here you select "Change activity / element number" as forbidden.
Now set this status to your network.
You can select the status profile by opening the network in CJ20N ->edit->Status->System/User Status, or by assigning the user profile to the transaction in customizing transaction:OPSC
Reagds
Muraleedharan.R

How to change the partition type on a table with data

Hi
I have a table, which is partitioned by list on date column. The table contains large volume of data.
My requirement is to make the list partition into range on the same date column.
I am working on Oracle10g
Kindly advice

partitioned by list on date How many distinct DATE values do you have ? Each DATE value would be a Partition in List Partitioning.
Why do you need to convert this to RANGE Partitioning ? How many DATE values do you expect in the table in the future ?
You can use DBMS_REDIFINITION to copy a LIST Partitioned Table to a RANGE Partitioned Table and then switch the tables at the end.
See examples (where the source table is not partitioned)
http://www.oracle-base.com/articles/misc/partitioning-an-existing-table.php
http://uhesse.com/2010/02/15/partitioning-a-table-online-with-dbms_redefinition/
But before converting I would justify why a LIST Partitioned Table be converted to RANGE Partitioned. Do you have Date-Range queries ?
Hemant K Chitale
Edited by: Hemant K Chitale on Mar 15, 2013 2:11 PM

How to change a partition?

I have already partitioned my 1TB external drive for 2 partition 600GB for the TM partition 1 and 400GB for partition 2.I do have stuff on both of them and just now I realized that I like to increase partition 1 TM to 750GB and have partition 2 250GB.Can this be done easily,I am pretty bad when it comes to MacsI just came over from Windows.

I am pretty bad when it comes to MacsI just came over from Windows.
After resolving this issue, see:
Switching from Windows to Mac OS X,
Basic Tutorials on using a Mac,
Mac 101: Mac Essentials,
Anatomy of a Mac,
MacFixIt Tutorials,
MacTips, and
Switching to the Mac: The Missing Manual, Snow Leopard Edition.
Additionally, *Texas Mac Man* recommends:
Quick Assist.
Welcome to the Switch To A Mac Guides,
Take Control E-books, and
A guide for switching to a Mac.

HT1338 how to change the partition of bootcamp

I install bootcamp for windows 7, now i find i need a biger partition

Not at all easy. Once Windows has been installed, it will always want to take up the same amount of space when restored.
Winclone is the only app I know of that can accomplish a resize of an installed Windows partition. I've used it to shrink my Win 7 install from 300 GB to a 50 GB partition.
Instructions here. You will of course first need to purchase Winclone. Make sure to back up everything first, including making your initial backup of your Windows partition with Winclone.

How can i actived mu id apple? i change my pasword 3 times and it still donsent qwork

how can i actived mu id apple? i change my pasword 3 times and it still donsent qwork

Boot from your recovery partition by holding down the key combination command-R at startup. Release the keys when you see a gray screen with a spinning dial.
When the recovery desktop appears, select Utilities ▹ Terminal from the menu bar.
In the Terminal window, enter “resetpassword” and press return. A Reset Password window opens.
Select your boot volume if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password.
Select  ▹ Restart from the menu bar.
You should now be able to log in with the new password, but you won't be able to unlock the Keychain. If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it. You’ll need to reset your keychain in the preferences of the Keychain Access application.

W520 active partition changed from lenovo 100MB internal to C: with Windows. Can't boot windows.

Hello!
I moved active system partition in diskmgmt.msc from lenovo 100MB internal partition (actually I'm not sure with the default size of the partition it migth be 1000MB or so I just remember visually digits, but I quess the partition is 100MB) to my C: partition. In result I can not boot up my system. All I can do after turning on notebook is to enter the bios.
I didn't remove lenovo partition I just clicked RMB on my C: partition in diskmgmt.msc and made it active. After reboot I can not load windows any longer.
How can I restore lenovo partition to be active?
Got Windows 7 64 bit.
Thanks in advance for any ideas
Kindest Pawel
P.S. I'am writing on Lenovo T400 which doesn't contain that lenovo internal partition, so I'm even more confused what is the purpose of it, maybe for security reasons or so...
Solved!
Go to Solution.

The "active" partition is where Boot Manager lives. The BIOS goes to the "active" partition to start the boot process, i.e. to launch Boot Manager which may utilize a boot manager menu to select which OS you want to boot to, if you have more than one bootable OS installed in multiple partitions. The boot manager menu also resides in this "active" partition.
If you install Windows7 from scratch on an empty drive, by default it will create a 100MB "system reserved" partition (i.e. the "active" partition, and which does NOT get a drive letter assigned to it when Windows comes up), along with a second large system partition for Windows itself (i.e. what you see as C). The entire rest of the drive is allocated to C by default, if you don't make any changes at cold install time.
So although it's possible to relocate Boot Manager and the boot manager menu into that large C partition (corresponding to changing that partition to be "active" and also de-activating the small "system reserved" partition which is no longer going to be used to begin the boot process), that is NOT the way the Windows installer builds things. And it's NOT the way Lenovo delivers the factory setup.
The Lenovo "system_reserved" partition from Lenovo is actually about 1.4GB rather than the usual 100MB. In it Lenovo places other utilities which get utilized during the system recovery process (which also uses the third partition Lenovo puts on the drive, i.e. the "recovery" partition). This is what allows you to truly recreate the factory-provided original hard drive steup if you need to or want to.
Anyway, it is possible to relocate the Boot Manager files into the C-partition if you had a true retail Windows 7 installation DVD. You could run "system repair" (rather than "install") three times in succession, and this would accomplish the deed. There are also utilities like EasyBCD which can relocate Boot Manager into the C-partition. Both of these processes would then allow you to delete the original "system reserved" partition (either the small 100MB one from MS, or the 1.4GB one from Lenovo... realizing of course that you would then lose the ability to use the "recovery partition" to restore Lenovo factory setup).
Also, if you install Windows 7 as a second bootable OS on a drive where WinXP was already installed, the Win7 installer would NOT create a "system reserved" (active) partition, as the existing WinXP partition is already marked as "active" and is where the current Boot Manager (from WinXP) lives. The Win7 installer replaces this (in the WinXP system partition itself, which is left untouched as the "active" partition) with the Win7 Boot Manager and menu, and creates a separatte new partition with Win7 in it. So now you have two bootable OS's, and no small "system reserved", and the WinXP partition contains Win7 Boot Manager and 2-OS boot menu, and is the "active" partition where the BIOS goes to start the boot process.
But honestly, there is really no reason to do any of the above with your W520. Just stick with what came from Lenovo. Some partition on the boot drive MUST be marked "active", and that's where Boot Manager and its menu MUST reside. Who cares whether that's in a small separate partition (which doesn't get a letter anyway), or in C? There's really very little to gain from changing this, other than a very small amount of additional hard drive space becoming "usable".

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

Yes, you can do something like that. What you would do is create a button for each image and then hide them. When I do this type of thing I place all of the buttons on a template page and then hide the template.
You can then use JavaScript to copy the icon from any of the hidden buttons to the main button that you've set up to display the image. For example, suppose you set up 10 buttons named b1, b2, b3, ...b10. The code to copy the icon from one of them to the button used to display the image (b0) would be something like this:
// Get the icon from the b3 button
var oIcon = getField("b3").buttonGetIcon();
// Get reference to the b0 button
var f = getField("b0");
// Set the icon of the b0 button to the icon retrieved from the hidden button
f.buttonSetIcon(oIcon);
// Show the b0 button
f.display = display.visible;
This code would go in the Mouse Up event of the smaller button.

How to change validity period of cost centre or activity type

Hi
How to change validity period for an Activity type or Cost centre?
Can we change the validity period once created?
regards
Prakash

Please note this can be done.
Go to Edit Cost Center
Goto Edit, Analysis Period.
Create a new validity period say today until 3112999
Change the data you want and save.
When you go into the CC again it will show two validity periods.

How to create recovery partition in new(changed) HDD.

my new HP pavilion g4 laptop HDD have crased, then I replce it by HP care. I upload original win 7 by recovery disk(DVD) but when I open my computer it shows only one partition (C drive, there is no recovery partition and HP tool.
So how to creates recovery partition by recovery disk(DVD)...........please help me.

Creating the recovery partition
Right-click the start orb, and start 'Disk Management'.
Shrink the C: drive by let's say 20-30GB.
Then create a new Partition and assign the R: label to it and name it RECOVERY.
Then open command prompt as administrator and type: 'recimg /createimage <directory>',
In this case: 'recimg /createimage R:\' to save it on the new partition.
This step may consume a lot of time.
Now we need to register the newly created recovery image: 'recimg /setcurrent <directory>'
'recimg /setcurrent R:\'
Voila you are done.
Restoring from recovery partition
You may want to use this restoring method by default, because it is the easiest way to do so if your recovery partition is still intact. If not, look at the other recovery methods to see which suits you best. This is usually the way you reset or refresh your Windows installation if you purchase a computer from a brand like Lenovo instead of building one yourself
Press the Windows-key + C to open the charms bar or swipe in from the right.
Click Settings.
Click Change PC Settings.
Click Update & Recovery in the menu on the left.
Click Recovery.
If all your documents are safe and sound in your user folder, you can use Refresh your PC without affecting files. However I still recommend taking a back-up... If you want to do a complete reinstallation of Windows and also clean your user folder in the process then choose Remove everything and reinstall Windows.

How to send active links in email from firefox. Works in IE but not Firefox... Is there a setting to change?

how to send active links in email from firefox. Works in IE but not Firefox... Is there a setting to change?
== This happened ==
Every time Firefox opened
== Always

Check with your web mail service provider for help with that issue.

How to change a TAB dynamically to be the active tab?

Hi,
I have a portlet written in Java and registered using a web provider. This portlet exposes a link which drives the content of another portlet through parameters&events.
This other portlet is placed on the same page but on a different TAB (!).
What I want is, when clicked on the link in Portlet1, this changes the content of the Portlet2 (via an event and parameter - that works) AND should change the TAB, so that the TAB which contains the Portlet2 is active and shown.
I couldn't figure out, how to change the TAB with an event or any other way. I can easily change the page through an event, but not to a tab on the same page. Do I overlook something or can I just don't use events for this?
Is there any API function which does changing tabs or getting the tab id or is there any other programmatic workaround to do dynamic tab changing?
If so, can someone point me to a code fragment?
Any help would be much appreciated.
Cheers,
Erik

A work around may be to change the location.href to the url of the tab you want to switch to.
Have you tried that already?

How to change active partition?

Similar Messages

Maybe you are looking for