How to change Cisco EPC2425 into bridge mode

Hi,
I need help regarding how to chage ECP2425 into bridge mode. I have Wireless NAS drive router which has its own DHCP and NAT service. At the moment my Wireless Timecapsule (NAS Drive) is in bridge mode and connected to EPC2425 with ethernet cable. Everything is fine. But in order to access my timecapsule over the internet, I need to use its (timecapsule)'s NAT service. For this, I need to put EPC2425 which is my first point of access from internet, into bridge mode or atleast disabled its (EPC2425) NAT service. Unfortunately, I am not been able to find NAT or Bridge mode option on EPC2425. I will appreciate if anyone can help me out in this case. I need to change my EPC2425 router into bridge mode or gateway mode.
Thank you very much                  

Hi Azhar,
Thank you for your question.  However, this community is for Cisco Small Business Products and the DPC/EPC2425 is not a Cisco Small Business Product.
Your product is an internet service provider (ISP) supported product.  In other words you need to contact your ISP or technology reseller that you purchased this from to help you with your question.
http://www.cisco.com/web/consumer/support/modem_DPC2425.html
http://www.cisco.com/web/consumer/support/prod_modems.html
Regards,
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business Products
www.cisco.com/go/smallbizsupport
twitter: CiscoSBsupport

Similar Messages

  • HT201974 how do you change your airport to bridge mode

    how do you change your airport to bridge mode?

    See your other post. Please, do not double post on the support forums, as it makes things very confusing.

  • How to put gateway into bridge mode

    I have my own router and would like to put my comcast provided equipment into bridge mode. Can you please provide instructions?

    http://customer.comcast.com/help-and-support/internet/wireless-gateway-enable-disable-bridge-mode
    http://forums.comcast.com/t5/Home-Networking-Router-WiFi/Gateways-and-Bridge-Mode/td-p/2419143

  • Why do I lose internet connection when I put airport extreme into bridge mode to correct Double NAT issue

    I reset my airport extreme router the other day because I was too lazy to reset the password on my private network.
    I have been reading the advice found on apple support communities and wide web, but the solutions do not solve any problems and often create new ones.
    I'm regretting because everything was working just fine.
    But I remember having this double nat error when I first set it up a few months back, but now I cannot resolve it.
    I would live with the yellow light, but it seems that this double nat error is preventing my playstation 3 from connecting to the airport extreme.
    When I put the aiport extreme into bridge mode, I loose all my wireless networks, even when I reboot the airport extreme and the modem.
    I try rebooting the modem, then the airport. and vice versa. No internet.
    I switch back to NAT/DCHP and the internet works fine on apple devices, but not the playstation 3, and I have the 1 Double NAT error.
    I have a plain stock Motorolla modem and I can dial in and see settings (although nothing about NAT). I didn't see where to see them.
    I tried setting the DHCP only but it said it didn't like the settings. is there a stock range i could be using?

    I have a plain stock Motorolla modem and I can dial in and see settings (although nothing about NAT). I didn't see where to see them.
    Exact model .. motorola make adsl, cable and probably wireless modems.. with some modems and some modem router.. we need exact info. What kind of broadband do you have?
    I would note.. some of the motorola cable modems seem to have issues with the apple routers. If you are about due to change modems.. now is a good time.. not another motorola.
    If the modem is a straight cable modem, the AE must be in router mode.. but you need to power down the cable modem. maybe for 20min so the new router can pick up the IP address.
    You cannot use DHCP alone.. the ISP do not give you a block of IP addresses.
    You cannot use bridge with a pure modem.. you will find it works.. but only to one device.
    The only reason you get double NAT is the failure to pick up the public IP.
    Give the info required..
    If you have trouble, I need the actual IP of the modem. the actual IP of the AE WAN port when plugged in. Screenshots are good.

  • HT201263 how to place your device into recovery mode without home button?

    How to place your device into recovery mode without home button?

    Try these programs:
    RecBoot: Easy Way to Put iPhone into Recovery Mode
    The Firmware Umbrella - TinyUmbrella

  • How to change 'z' key into 'A' key with key blinding?

    How to change 'z' key into 'A' key?
    Although txt.setText("A") can set the text field with 'a', but it is not original input from keyboard because it cant trigger the key listener.
    It is possible to perform key pressing more than a key in same time? Example, perform 'q' & 'w' keys pressing at the same time.
    import javax.swing.*;
    import java.awt.*;
    import java.awt.event.*;
    public class Main
    {   public static void main(String[] args)
        {   JFrame f = new JFrame("Test");
            Test GUI = new Test();
            GUI.setOpaque(true);
            f.setContentPane(GUI);
            f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
            f.pack();
            f.setVisible(true);
    class Test extends JPanel
    {   JTextArea txta = new JTextArea(10,20);
        JTextField txt = new JTextField(10);
        JScrollPane sp_txta = new JScrollPane(txta);
        public Test()
        {   this.setPreferredSize(new Dimension(400,300));
            setLayout(new BorderLayout());
            txta.setEditable(false);
            add(sp_txta, BorderLayout.CENTER);
            add(txt, BorderLayout.PAGE_END);
            Action testAction = new AbstractAction()
            {   public void actionPerformed(ActionEvent ae){ txt.setText("A"); }
            txt.getInputMap().put(KeyStroke.getKeyStroke('z'), "test");    //Change z into A
            txt.getActionMap().put("test", testAction);
            txt.addKeyListener
            (   new KeyListener()
                {   public void keyPressed(KeyEvent e){ txta.append(e.getKeyChar() + " key is pressed \n"); }
                    public void keyReleased(KeyEvent e){ txta.append(e.getKeyChar() + " key is released \n"); }
                    public void keyTyped(KeyEvent e){ txta.append(e.getKeyChar() + " key is typed \n"); }
    }Edited by: 835972 on Feb 11, 2011 8:11 AM

    It is possible to perform key pressing more than a key in same time? Example, perform 'q' & 'w' keys pressing at the same time.With r.keyPress method, it only can perform single key pressed at a time. Do you have any idea how to perform multiple key pressed at a time?The javadoc for Robot.keyPress suggests ( "+The key should be released using the keyRelease method+" ) that the key remains "pressed" until you keyRelease(...) it. So, press the keys sequentially:
    theRobot.keyPress(KeyEvent.VK_Q);
    theRobot.keyPress(KeyEvent.VK_W);
    // At this stage both Q and W are pressed "in same time"
    ... // do stuff
    theRobot.keyRelease(KeyEvent.VK_W);
    // At this stage, only Q is pressedI suspect that in real life, unless you're a very gifted musician, you don't really press keys "at the same time" (under the time resolution of a keyboard, which I imagine is around a few milliseconds).

  • I have just installed Illustrator CS6 yesterday, but I found it was in French. Could help me figure out how to change the language into English?

    I have just installed Illustrator CS6 yesterday, but I found it was in French. Could help me figure out how to change the language into English?
    I got my series number from my Institut (which is in Paris, FR). I do not use Creative Cloud.
    When I was installing the software, I cannot select a language.
    Could you help me with my problem? Do I have to get a different series number?

    lunc,
    You will have to get a new application in English, to replace the French one.
    You, or your Institute will have to get help from Adobe, I am afraid.
    You may try a chat here,
    Get help with orders, refunds, and exchanges (non-CC, chat open between 5AM and 7PM PST/PDT on workdays)
    http://helpx.adobe.com/x-productkb/global/service-b.html
    or (have your Institute) talk to Adobe in France
    http://helpx.adobe.com/adobe-connect/adobe-connect-phone-numbers.html
    If you fail to get any help, please report back here, and I will ask a special forum staff friend to try to find the right one at Adobe to have things sorted out.

  • How to add extra labels into Bridge CS5?

    Hi folks, nice to meet you all.
    I do not want to edit or rename the existing 5 existing labels into Bridge CS5. I just want to create new labels. So, I want to add extra labels to have more than 5 labels.
    Does anybody know how to add extra labels into Bridge CS5? If so, please, tell me how to do it.
    Thanks.

    You should move this post to the new Bridge forum as this one will soon die.  Here is link http://forums.adobe.com/community/bridge/general

  • How to boot your phone into safe mode

    If you experience any problem with your phone, booting it into safe mode can be a good idea to check if any third party applications might be involved in the problem you’re having.
    If you run your phone in safe mode for a while and you don’t experience any problem, the problem you’re having is most likely related to a third party app that you’ve installed.
    How to boot into safe mode differ from models to model and it can also be different depending on firmware version but this topic will explain to you how to do it.
    NOTE!
    Booting into safe mode may change personal UI customizations such as icons and folders.
    Later Xperia phones running on Android Jelly Bean (Android 4.1 or later)
    Press and hold the on/off key until you get this screen.
    Now tap and hold the Power off option until you see this screen.
    Press OK to reboot into safe mode.
    If you have successfully booted into safe mode you will see the text Safe mode in the bottom left corner.
    You can also boot into safe mode by turning off the phone and wait a few seconds. Now press and hold both the on/off and volume down (-) key. Keep pressing these two keys until the phone has booted completely.
    To exit safe mode you simply power off and power on as normal.
    Xperia phones using touch menu key running on Android GB (2.3.X) or ICS (4.0.X)
    Turn off your phone.  Wait a few seconds and then turn it on again. Now during the boot process start tapping the menu key continuously and keep tapping until the phone has booted completely. Not too fast, not too slow. The beat of Iron man by Black Sabbath is just right.
    To exit safe mode you simply power off and power on as normal.
    Xperia phones using hardware menu key
    Turn off your phone.  Wait a few seconds and then turn in on again. Now during the boot process press and hold the menu key until the phone has booted completely.
    To exit safe mode you simply power off and power on as normal.
     - Community Manager Sony Xperia Support Forum
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

    Hi Annthias,
    Welcome to the community,
    Try clearing out the Camera application first.
    Menu > Apps > All > Camera > Clear Cache > Clear Data
    Let us know if the issue continues.

  • Ibooks 3.1 how to change horizontal scroll into vertical scroll

    update to ibooks 3.1, the scroll mode is changed into horizontal scroll, now in my .epub books it cut so many picture in two parts and display in two pages...how to change , back to vertical mode...

    I find this maybe is the new feature only for books with Asia-Pacific words....english books is right with vertical scrolling mode...but chinese books whit horizontal scrolling mode
    why apple doesn't make a set up to change between this ..

  • How do I up it into dfu mode?

    How do I put an Ipod touch into dfu mode?

    I followed the instructions below but I dont get anything that says "DFU" mode. itunes says recovery mode but neither the touch nor itunes says "DFU"
    A small guide on how to put your iPod touch / iPhone  into DFU mode. Works with all G’s of iPod touch / iPhone What is DFU: Device Firmware Upgrade
    Step 1: Turn off your iPod touch / iPhone completely and connect to PC / mac
    Step 2: Hold down the Power button for 3 seconds
    Step 3: Without releasing the power button, also hold the Home button for 10 seconds
    Step 4: Without releasing the home button, release the power button and keep holding the Home button  for 20 seconds. Itunes will identify that you are in DFU mode.

  • How to put iPod 5G into retail mode

    How can I put iPod 5G INTO RETAIL MODE AS I RUN A PHONE SHOP

    What do you mean by retail mode?
    Apple uses their own custom iOS mods to have iOS devices for demonstration in their stores.
    You can do some restrictions of use of the iOS device by using Guided Access. See:
    http://support.apple.com/kb/ht5509

  • How to Change the Fields from Input mode to display mode

    Hi experts,
    Here is my business requirement. I need to show certain fields in the PRICING TAB OF SALES ORDER  in display mode. Now for this i am using the BADI definition CRM_PRICING_BADI.
       Now, can anybody tell me how to change the field type from input mode to change mode?

    Hi Karan,
      In your BADI has a parameter CT_INPUT_FIELD_NAMES with one field called CHANGEABLE with values:
         Field Can Be Changed
    A     Field Cannot Be Changed
       Assing this values to your fields according with your requirements.
    Regards.
    Manuel

  • How To Access Files Remotely In Bridge Mode?

    Hey guys, so I've got a TC and my roomate has a TC the only way we can get them both to work is hooked up to our router and placing both TC's to Bridge Mode. The issue is in Bridge Mode we've lost a lot of remote functionality. The main thing we both want to do is access our files when we're on the go. Is there a way to remotely access our TCs in bridge mode? I'm pretty techy so I'm open to any creative solutions.

    but how will this solve the problem where I don't see "Share disks over WAN" on my TC?
    The TC does not need that option....since it is already in Bridge Mode. 
    If the TC were also your router.....then it would be providing DHCP and NAT service....and the option to "Share..." would be needed....so it would appear so you could allow or open the WAN port. The example that Tesserax provides assumes that the TC is also the router......providing DHCP and NAT service.
    You have a different layout. Another device is providing the DHCP and NAT routing, and the TC  is in Bridge Mode.
    Are you saying that option will become available when my TC sees the approptiate port is open?
    You don't need the "option" at all in Bridge Mode.  All ports are already open when the TC is in Bridge Mode. There is no WAN port in Bridge Mode....it automatically becomes a LAN port, so no need to "open" a port if it is already "open".

  • How to setup time capsule in Bridge Mode

    How do I set up my airport base station in Bridge Mode?

    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click on the base station, then click Edit in the small window that appears
    Click the Network tab at the top of the next window that appears
    Insure that the setting for Router Mode = Off (Bridge Mode)
    Click Update and wait a full minute for the base station to restart
    It would be a good idea to also.....
    Power off both your main router and the base station
    Wait a minute or two
    Start up the main router first and let it run a full minute
    Start up the base station next the same way

Maybe you are looking for