How to change default action when a device is connected to Windows 8

The first time I connected my Android phone to Windows 8, I selected an default action (view files in Windows Explorer.)
Now I would like to change that default. Where/how do I do that?
Thanks,
Jim Kay
Jim Kay

From http://windows.microsoft.com/en-gb/windows-8/autoplay-faq search in the start screen for Autoplay, go into settings and then click Change default settings for media or devices.
Look through the list and find your phone (should be down at the bottom of the list) and change the action.

Similar Messages

How to change default action "alarm" for all signatures ?

My question belongs to a Cisco 1712 (128 MB, IOS 12.3T, SDM 2.5 installed):
I'm trying to change the default action "alarm" to "alarm,reset,drop" for all signatures of my custom set.
However doing so via SDM fails. First, it appears as being done correctly, but after compiling the signatures again, the default values are back there (in the same sense, I was unable to delete signatures, works just using the CLI).
I followed the instructions at cisco.com:
router(config)#ip ips signature-definition
router(config-sigdef)#signature 6130 10
router(config-sigdef-sig)#engine
router(config-sigdef-sig-engine)#event-action produce-alert
router(config-sigdef-sig-engine)#event-action deny-packet-inline
router(config-sigdef-sig-engine)#event-action reset-tcp-connection
router(config-sigdef-sig-engine)#exit
However ip ips signature-definition is not understood by the router, so the procedure fails.
Can you please assist me ?

You can use IOS command-line interface (CLI) to change signature actions for one signature or a group of signatures based on signature categories. The following example shows how to change signature action to alert, drop and reset for signature 6130 with subsig ID of 10.
router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
router(config)#ip ips signature-definition
router(config-sigdef)#signature 6130 10
router(config-sigdef-sig)#engine
router(config-sigdef-sig-engine)#event-action produce-alert
router(config-sigdef-sig-engine)#event-action deny-packet-inline
router(config-sigdef-sig-engine)#event-action reset-tcp-connection
router(config-sigdef-sig-engine)#exit
router(config-sigdef-sig)#exit
router(config-sigdef)#exit
Do you want to accept these changes? [confirm]y
router(config)#

How to change default properties when uploading role

Hi, all.
Our env. is like the following.
   EP 6.0 SP9 patch1
   J2EE SP9
   Windows 2003 MS SQL Server
When we upload a role from R/3 to EP, role is correctly uploaded but the problem is the following default behavior.
- default property of entryPoint for role is set to "false"
- default property of GUI type for Transaction iView is dependent on the GUI support of R/3 SE93(Maintain Transaction Codes)
Is there any way to change these default settings to some other values in EP without modification?
What we want to do is that when we upload roles, we want to set the following values by default.
- entryPoint = "true"
- GUI type = "SAPGUI for Windows"
One way would be to use Content Administration --> Multiple Property Replacement feature but we want to reduce our operation time more.
Thanks.

Hi Sejoon
Even i'm in the same situation, i tried modifying transaction type in the
com.sap.portal.appintegrator.sap.bwc.Transaction which is iview template for all the iviews created on import of roles..but it also dint work.
yeah Multiple replacement is not the best of the option,
let me know if u have figured out something.
-Krishna

How to change default DC that AD snap-in connects to

I installed RSAT tools on a Windows 7 VM. Every time I open Active Directory it connects to the DC that is geographically the farthest away -- across the country!!! MAKES SOOOOOOOOO MUCH SENSE. How can I configure the snap-in to connect to something more
practical? Like the DC on the same network as the RSAT management computer?? Getting livid by the fact I need to google simple things like this lately...........
OK. I reluctantly went to GOOGLE again and found this: http://support.microsoft.com/kb/214676.
;adlkjfalkdjfkqa;lgakfnddk,mv asgvz
sd'fgfsd;g nslrdkjgnlskfjdbz 'fd
vsdf
sdf sdf sdf;gb s
df
AHHHHHHHHHHHHHHHHhhh!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

You need to define sites and subnets in Active Directory to control the selection of DCs for authentication, replication and the DC being automatically used by ADUC.
http://technet.microsoft.com/en-us/library/cc754697.aspx
Run the following command on your machine where you trying to run ADUC from, it will report the site it will select a DC from:
nltest /dsgetsite
Enfo Zipper
Christoffer Andersson – Principal Advisor
http://blogs.chrisse.se - Directory Services Blog

How to change default compile directory tmp_ejb?

Dear all,
Someone knows how to change the default directory "tmp_ejb...." in WebLogic Server
7.0?
This is the default directory where WebLogic Server 7.0 generates and compiles
the EJB's declared in config.xml.
I try to specify the attribute TmpPath="ANOTHER_TMP_LOCATION_DIRECTORY_FOR_EJB"
in the EJBContainer node but still doesn't work.
The same thing happens when I test this attribute on EJBComponent declaration.
Someone knows if there is an enviroment variable that specify this tmp_ejb location
path?
It's false that the tmp_ejb is located where the config.xml file is placed.
I have 3 weblogic servers and they haven't the same behaviour.
Someone can help me??????
Thanks.

I ran into the same problem and was wondering if you got an aswer the question you posted in BEA's news group: "How to change default compile directory tmp_ejb?
Thanks

How to change default Ovi Player store ...

Hi,
I need help from you people.
I had installed Ovi Player. Whenever I try to open Ovi Player, the default store gets’ open is "India". I change the store location to "Germany". When I do the search for particular music, it will again take me to "India" store instead of "Germany" store. In addition, most annoying is that I have to re-login but my user id and password will not work as its different store. Also when I go via music.nokia.de and try to login, it open Ovi player and since default location is "India", it takes me to India store and my login credentials do not work.
I ask Nokia care on how to change default Ovi Player Store location but they are unable to provide any good answer.
I already un-install / re-installed but won't work. Do any of you have answer to my problem? I want my default Ovi Player location to be "Germany" instead of "India".
More information, my regional settings have location as “Germany” and language as “English”.
Please help.
Thanks for your response.
Regards,
Subhendra
Nokia N97 Black
RM-505
V12.0.026
0586701
Solved!
Go to Solution.

I had got message from Nokia on how to correct this issue. This had solved the problem. Below is the mail from them ...
Dear Chakraborty,
Thank you for your response.
This error is sometimes caused by a corrupted MDataStore.db3 file used by the Ovi Player. This file will need to be deleted with the Ovi Player closed. Then open the player and the datastore file will be rewritten by the application:
Close Ovi Music Player and delete the MDataStore.db3 file:
Vista C:\Users\<user>\AppData\Local\Nokia\Nokia Data Store\DataBase\MDataStore.db3
XP C:\Documents and Settings\<user>\Local Settings\Application Data\Nokia\Nokia Data Store\DataBase\MDataStore.db3
Both of these locations are in hidden folders. So, to view them users will need to:
Open Windows Explorer > Tools > Folder Options > View > Show Hidden Files and Folders
Once Ovi Music is opened again the MDataStore.db3 file will be rewritten to this folder.
  After that manipulation try to install the Ovi Player once again:
http://europe.nokia.com/explore-services/music/nokia-music
  Best regards
Nokia Care Team

How to change Default editor in Linux for PL/SQL Programming

Deare friends ,
I am using oracle 8i (8.1.6) on RedHat Linux 7.2 , But i donot know how to change default editor for modify editor on sql prompt say ex:-
In winodow
SQL> ED
it open nope pad to modify sql and pl/sql statement
while in linux
SLQ > ED
it open one editor but it is not easy to work and i want to change that editor so could you tell me how to chane editor i want to use vi editor .
if any boyd know reply me on :-
[email protected]
or on this forum
Thanking you in advance
Piyush Patel

Either manually do a 'define editor=vi' when you log in through sql*plus, or put that in the glogin.sql in $ORACLEHOME/sqlplus/admin or put that in a login.sql in the directory you run sqlplus from.

HT4199 how do I fix it when "another device is using computer IP address" and I can't get wireless to work anymore? It used to work fine.

How do I fix it when "another device is using computer IP address"? Airport used to work fine. I've already tried turning everything on and off several times.

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

With per-message S/MIME enabled, the default action when replying to an encrypted message is to send that reply unencrypted. Causes users to accidentally send originally encrypted content, back unencrypted.

This seems counter-intuitive, are we doing something wrong or is this working as expected?
When we have per-message S/MIME enabled on an iOS 8 device. Everything works as expected and we have the ability to select when you are sending an email whether that email should be encrypted or not, but i've noticed that, when you receive an email encrypted with your S/MIME cert, read that email on your iOS8 device with per-message S/MIME enabled, and reply to, or forward, that message, the default action is to send that reply, or forward, unencrypted UNLESS you manually re-tap the little padlock button to re-encrypt the message.
This seems broken. I would imagine we would want the default action when replying or forwarding that encrypted message to be an encrypted reply or forward so as to keep the encryption intact. I can't think of a time when you would actually want to send an unencrypted reply to an encrypted message, as doing so would send the originally encrypted content back, as unencrypted text therefore negating the point of ever encrypting it in the first place.
I know we can set the iOS device to by default send ALL email as encrypted, but that's overkill. Our users probably only get 1 or 2 encrypted emails a week, but when they do get those encrypted email we would want their replies and forwards to those email to also remain encrypted, and not open up the chance of one of these users forgetting to re-check the padlock button thus accidentally sending the originally encrypted content, out as an unencrypted message.
Is this working as expected or are we doing something wrong?

Hi,
Thank you for your clarification.
Yes, it seems you have installed all the updates for the Outlook.
“Testing on a good computer” is a method to narrow down whether the cause is related a specific computer.
For debugging tool, I think we can take a look at:
1. RPCTrace log
2. Process Monitor
For RPCTrace log, it’s not that easy to capture. You must firstly replace some Outlook dll files before you can capture the log. Even more, the dll files can vary if the Outlook
SP versions are different. So, It’s recommend to contact a Microsoft Support to capture and analyze the trace log.
Thanks,
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Simon Wu
TechNet Community Support

How to change default approval for ResourceAuthorizerApproval ?

Hi,
I'am new in OIM and I follow documentation where I found some predefined workflows. I'd like to use them.
Could you tell me, step by step, how to change default approval for ResourceAuthorizerApproval (only for my new defined resource).
I'm using OIM 11g and Design Console 11.1.1.3.0.2.0

Ok, I made new tamplate (copy of existing one), there I changed Template Level Approval Process and set allowed resources. It seems to be ok :)
If there are other solutions please share with me
Thanks
M.

How to change default Current Flag values for SCD2?

I'd be curious to find out how to change default Current Flag values for SCD2 (instead of 0/1 to use N/Y)
Probably I can change IKM module .... is there another way?
Thanks

Hi,
You need change the IKM. This values are hardcode in the IKM.
You can create a new IKM and the values used are a options of the IKM.
Regards
Edited by: Uthred on May 18, 2009 4:27 PM

How to change default save as location

hi,
how to change default save as location in acrobat 7.0?

Why is Acrobat involved in this process at all? Why don't you save directly the pdf from your email program directly where you want it to be? Acrobat is just adding another step to this process.

How to change default ringtone to a custom one for IPhone 5.

I have gone into settings through Sounds made the change, but it does not register as the default even though the ringtone chosen has the checkmark beside it. Ringtone still lists the factory default under sounds & vibrations.
I am able to customize ringtones for individual contacts.

user598986 wrote:
Hi,
How to change default value in a table
I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
ALTER TABLE test
MODIFY (indicator DEFAULT 'I');
Incidentally, INDICATOR is a keyword in Oracle, so you may have problems using it as a column name. If so, you'll have to enclose the column name in double-quotes, and be careful to use capital letters inside the quotes.
Edited by: Frank Kulash on Aug 26, 2009 11:42 AM

How to change default value in a table using ALTER TABLE

Hi,
How to change default value in a table
I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
Any help will be needful for me
Thanks and Regards

user598986 wrote:
Hi,
How to change default value in a table
I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
ALTER TABLE test
MODIFY (indicator DEFAULT 'I');
Incidentally, INDICATOR is a keyword in Oracle, so you may have problems using it as a column name. If so, you'll have to enclose the column name in double-quotes, and be careful to use capital letters inside the quotes.
Edited by: Frank Kulash on Aug 26, 2009 11:42 AM

How to change default encoding in DataBindings.cpx

Hello,
How to change default encoding in DataBindings.cpx,
on windows-1251 for instance?

I've filed Bug# 3147045 for this. Our DataBinding.cpx file and UIModel XML files seem to be getting hardcoded to use the ISO-8859-1 encoding. Our ADF Business Components XML files correctly pickup the IDE encoding.

How to change default action when a device is connected to Windows 8

Similar Messages

Maybe you are looking for