How to change default admin password on Cisco Aironet 1040

How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?

Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all            Applies the configuration to every AP that does not have a specific user name.
     Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses ****

Similar Messages

  • How to change default PIRWBUSER password for ABAP Proxy monitoring ?

    Hi,
    Please advise how to change setting for PIRWBUSER in PI so no need to use master password PI in ECC server.
    In the Message monitoring you can have option to monitoring ABAP Proxy transaction in the other SAP Instance. But of course you need to have PIRWBUSER in that target SAP instance.
    How to change this configuration for PIRWBUSER for other SAP Instance. because other SAP instance it migh have different password for PIRWBUSER ?
    Regards
    Fernand

    Hello there.
    Please check the note below according to your system:
    #999962 - PI 7.10: Change passwords of PI service users
    #936093 - XI 7.0: Changing the passwords of XI service users
    #721548 - XI 3.0: Changing the passwords of the XI service users
    Regards,
    Caio Cagnani

  • ThinkPad USB 3.0 Secure Hard Drive - I can not change Default admin password

    I followed all the instructions from the manual guide but the password cannot being changed.
    enter in admin mode, then hold lock plus 9 until led flash in blue 
    input a new password (of course between 8 and 16 digits lenght)
    then the led flash in green three times, but then the led flash in blue and then flash in red and then in blue again as the password had wrong length.
    The manual does not provide furthe action to troubleshoot.
    is the device wiht defect?
    Any hint would be appreciated.
    Thanks,
    Marceloap

    Hello Denmark calling.
    Solution for you’re:
    ThinkPad USB 3.0 Secure Hard Drive problem.
    In order to set the Admin pass, you will have to do the following
    1. Press 0+OK for 5 sec, enter "12345678" and OK       = BLUE LED   (Admin mode)
    2. Press OK+9                                                                        = BLUE LED flashes
    3. Enter admin code with correct fashion, and then OK = BLUE LED flashes   (and now most important)
    4. Re-enter admin code, and OK                                        = BLUE LED.
    This must be done before attempting to change user password. (Obvious reasons)
    For User code change.
    This can be changed by accessing the admin mode first = BLUE LED
    And then         
    1+OK                                                                                            = BLUE LED flashes
    Re-enter user code and OK                                                    = BLUE LED
    For User code and Admin code there is not mentioned any reference online reference supplied by Lenovo, which tells the new proud owner the correct way to alter standard codes.
    But let it be said that in my humble opinion this is a (almost) great product (SSD would make the difference for me personally)
    Hopes it helps
    TaR

  • How do I change the admin password in SJSWS 7.0?

    I've googled this, searched the forums, read the manual, but I haven't found anything that explained how to change the admin password for SJSWS 7.0. So, right now I'm stuck with "adminadmin" as the password, which I think is the default since I don't remember specifying that during install. Clearly I can't use this in production with the default admin password... sorry if this is a rtfm question, but I really didn't see anything in the manual about changing the admin password. Thanks!

    You could use the following CLI command:-
    wadm> set-admin-prop --set-password
    More information about the command:-
    http://docs.sun.com/app/docs/doc/819-3283/set-admin-prop-1?a=view
    You could also use Administration console-
    - Login to the Administration Console and click on the Nodes tab
    - In the Nodes page, click on the Administration Server link within the Nodes table
    - Go to "Administration Server Preferences" section in the General page and change the password

  • How to change default Ovi Player store ...

    Hi, 
    I need help from you people.  
    I had installed Ovi Player. Whenever I try to open Ovi Player, the default store gets’ open is "India". I change the store location to "Germany". When I do the search for particular music, it will again take me to "India" store instead of "Germany" store. In addition, most annoying is that I have to re-login but my user id and password will not work as its different store. Also when I go via music.nokia.de and try to login, it open Ovi player and since default location is "India", it takes me to India store and my login credentials do not work.  
    I ask Nokia care on how to change default Ovi Player Store location but they are unable to provide any good answer.  
    I already un-install / re-installed but won't work. Do any of you have answer to my problem? I want my default Ovi Player location to be "Germany" instead of "India".  
    More information, my regional settings have location as “Germany” and language as “English”.  
    Please help. 
    Thanks for your response.
    Regards,
    Subhendra
    Nokia N97 Black
    RM-505
    V12.0.026
    0586701
    Solved!
    Go to Solution.

    I had got message from Nokia on how to correct this issue. This had solved the problem. Below is the mail from them ...
    Dear Chakraborty,
     Thank you for your response.
     This error is sometimes caused by a corrupted MDataStore.db3 file used by the Ovi Player.  This file will need to be deleted with the Ovi Player closed.  Then open the player and the datastore file will be rewritten by the application:
     Close Ovi Music Player and delete the MDataStore.db3 file:
     Vista C:\Users\<user>\AppData\Local\Nokia\Nokia Data Store\DataBase\MDataStore.db3
     XP C:\Documents and Settings\<user>\Local Settings\Application Data\Nokia\Nokia Data Store\DataBase\MDataStore.db3
     Both of these locations are in hidden folders.  So, to view them users will need to: 
     Open Windows Explorer > Tools > Folder Options > View > Show Hidden Files and Folders
    Once Ovi Music is opened again the MDataStore.db3 file will be rewritten to this folder.
      After that manipulation try to install the Ovi Player once again:
     http://europe.nokia.com/explore-services/music/nokia-music
      Best regards
     Nokia Care Team

  • How to change Default editor in Linux for PL/SQL Programming

    Deare friends ,
    I am using oracle 8i (8.1.6) on RedHat Linux 7.2 , But i donot know how to change default editor for modify editor on sql prompt say ex:-
    In winodow
    SQL> ED
    it open nope pad to modify sql and pl/sql statement
    while in linux
    SLQ > ED
    it open one editor but it is not easy to work and i want to change that editor so could you tell me how to chane editor i want to use vi editor .
    if any boyd know reply me on :-
    [email protected]
    or on this forum
    Thanking you in advance
    Piyush Patel

    Either manually do a 'define editor=vi' when you log in through sql*plus, or put that in the glogin.sql in $ORACLEHOME/sqlplus/admin or put that in a login.sql in the directory you run sqlplus from.

  • Can't change the admin password in HSS

    Hi all,
    I want to change the default admin password to a different one,
    I thought I could change it via HSS but when I open the properties menu, there is no option to change password,
    Does anyone know a different way?
    Thanks,
    Yuval

    You can also change the Password from Your relational db
    For Example
    Go to db and Type in query
    Select * from css_users;
    Result
                                                                User         Password
    native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER admin {SSH2}L+o8ap4rF392KtWf6/druBlx96bqIOcvRh+fbSdeeXNyjdMLdSTEpmB0nJBqaJoF Administrator Shared Services Administrator 1 Shared Services System Shared Services System
    Edit the Password column line
    "{SSH2}L+o8ap4rF392KtWf6/druBlx96bqIOcvRh+fbSdeeXNyjdMLdSTEpmB0nJBqaJoF"
    and replace with Password123
    and save the query .You need to restart the hyperion server and login into the shared services with lastest password
    Thanks,
    Sreekumar Hariharan

  • Cisco connect software wants to match the admin password to cisco connect password?

    As much as possible i want only one SSID for my router, so i dont want to have another SSID for guest. To protect my router
    settings I need to have a different admin password from those of passphrase (i.e. wifi password).
    Why is it that cisco connect software wants to match the admin password to cisco connect password?
    The cisco connect password is the same as the passphrase. I think its unsafe to have similar passes for both admin password
    and passphrase.
    Is there any way that cisco connect software would work under different admin password & passphrase?

    From what I can tell, the router is set up so that it broadcasts two seperate SSID's with two unique passwords.  If you logon to the SSID-Guest network, you are not allowed any kind of Admin access to the router.  If you attempt to use the Cisco Connect software, you'll eventually get an error saying that it could not find a network (unless there is an unconfigured router running factory defaults in range).  I verified this using a Cisco Linksys E4200 and a few laptops.
    So long as you utilize the guest network properly, you should be able to maintain security on your network and use Cisco Connect.  Obviously this isn't ideal for most commercial use, but then again I don't know why you would want to use this software on that scale.
    If you are trying to keep one SSID for the network, I think you're going to have to use the web based service and do a little manual configuration.  
    TLDR:  Seta different password for the guest network and never give out the primary network password.  Guests don't have admin access, even while using Cisco Connect so long as they are connected to the -Guest SSID.

  • HT1338 How to retrive my admin password

    How to retrieve admin password for mac if its forgotten?

    It can't be retrieved but it can be changed which is effectively the same thing except for the Keychain Access application which will retain the old password.
    If you wish to change your Admin password, follow these instructions.
    OS X: Changing or resetting an account password

  • How to change default compile directory tmp_ejb?

    Dear all,
    Someone knows how to change the default directory "tmp_ejb...." in WebLogic Server
    7.0?
    This is the default directory where WebLogic Server 7.0 generates and compiles
    the EJB's declared in config.xml.
    I try to specify the attribute TmpPath="ANOTHER_TMP_LOCATION_DIRECTORY_FOR_EJB"
    in the EJBContainer node but still doesn't work.
    The same thing happens when I test this attribute on EJBComponent declaration.
    Someone knows if there is an enviroment variable that specify this tmp_ejb location
    path?
    It's false that the tmp_ejb is located where the config.xml file is placed.
    I have 3 weblogic servers and they haven't the same behaviour.
    Someone can help me??????
    Thanks.

    I ran into the same problem and was wondering if you got an aswer the question you posted in BEA's news group: "How to change default compile directory tmp_ejb?
    Thanks

  • How to change default approval for ResourceAuthorizerApproval ?

    Hi,
    I'am new in OIM and I follow documentation where I found some predefined workflows. I'd like to use them.
    Could you tell me, step by step, how to change default approval for ResourceAuthorizerApproval (only for my new defined resource).
    I'm using OIM 11g and Design Console 11.1.1.3.0.2.0

    Ok, I made new tamplate (copy of existing one), there I changed Template Level Approval Process and set allowed resources. It seems to be ok :)
    If there are other solutions please share with me
    Thanks
    M.

  • How to change default Current Flag values for SCD2?

    I'd be curious to find out how to change default Current Flag values for SCD2 (instead of 0/1 to use N/Y)
    Probably I can change IKM module .... is there another way?
    Thanks

    Hi,
    You need change the IKM. This values are hardcode in the IKM.
    You can create a new IKM and the values used are a options of the IKM.
    Regards
    Edited by: Uthred on May 18, 2009 4:27 PM

  • How to change default save as location

    hi,
    how to change default save as location in acrobat 7.0?

    Why is Acrobat involved in this process at all? Why don't you save directly the pdf from your email program directly where you want it to be? Acrobat is just adding another step to this process.

  • How to change default ringtone to a custom one for IPhone 5.

    I have gone into settings  through Sounds made the change, but it does not register as the default even though the ringtone chosen has the checkmark beside it.  Ringtone still lists the factory default under sounds & vibrations.
    I am able to customize ringtones for individual contacts.

    user598986 wrote:
    Hi,
    How to change default value in a table
    I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
    I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
    ALTER TABLE  test
    MODIFY (indicator DEFAULT 'I'); 
    Incidentally, INDICATOR is a keyword in Oracle, so you may have problems using it as a column name. If so, you'll have to enclose the column name in double-quotes, and be careful to use capital letters inside the quotes.
    Edited by: Frank Kulash on Aug 26, 2009 11:42 AM

  • How to change default value in a table using ALTER TABLE

    Hi,
    How to change default value in a table
    I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
    I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
    Any help will be needful for me
    Thanks and Regards

    user598986 wrote:
    Hi,
    How to change default value in a table
    I have a table TEST which has 2 fields CODE of Datatype VARCHAR2(10) and Indicator as VARCHAR2(1).
    I want to change the default value using ALTER TABLE TEST of field Indicator to 'I'.
    ALTER TABLE  test
    MODIFY (indicator DEFAULT 'I'); 
    Incidentally, INDICATOR is a keyword in Oracle, so you may have problems using it as a column name. If so, you'll have to enclose the column name in double-quotes, and be careful to use capital letters inside the quotes.
    Edited by: Frank Kulash on Aug 26, 2009 11:42 AM

Maybe you are looking for

  • Looking for some good documents on performance tunning

    Hi, please excuse me, as this is not a technical issue.as i am looking for some good ebooks ,can anybody suggest me some good site from where i can download free. or any metalink number. Message was edited by: user00726

  • Date & Time in menu bar not updating

    My "Date & time" info in the top right menubar does not "run": it only updates to the current time when I click it. I have it set as digital showing seconds but it just doesn't run, it's stuck on the last date/time I updated by clicking it. I never h

  • Recording starting too early and also ending too e...

    Another problem..... When recording programmes I am frequently finding that the recording is starting way too early...5-10 minutes....and often ends too early (very annoying as one misses the end of a particular programme). Any help, gratefully recei

  • Inventory Report with Trading Partners & Cost of Sales

    Hi Freinds, We have activated the Trading Partners in the document types relating to the Invoice Verification and Goods Receipts. Accordingly when we do the GR or the Invoice Verification, the Trading Partner information gets picked up at the time of

  • GL Trial Balance has no data using Parent Value

    I have setup a company parent value with two children values. I went to run the stamdard trial balance 1 summary report for the parent value and the report shows no data. Are only fsg's able to print parent value reports? Thanks fin advance.