How to change hard drive on MacBook

How do I install a new hard drive on a MacBook  please

•Mac Laptop Repair  Guides - iFixit:
http://www.ifixit.com/Device/Mac_Laptop
http://www.ifixit.com/Device/MacBook
Depending on the identity of the product, details of the process
will vary somewhat; and the data speed of the hard drive bus
may affect alternative replacements, such as an SSD upgrade.
Good luck

Similar Messages

  • How to replace hard drive in macbook pro?

    How to replace hard drive in macbook pro?

    Hi S,
    If you have the newer unibody style, it's very easy. If it's one of the earlier models, it's considerably more difficult. Go to Apple Menu > About This Mac > More Info > Hardware and find your Model Identifier. Then go to ifixit.com, or powerbookmedic.com or macsales.com or youtube or others and there are illustrated, detailed directions. Good luck to you and post back if you have further questions.

  • How to Clone Hard Drive from Macbook Pro to Macbook Pro with Retina

    Hey everyone! I had a question about cloning my laptop's hard drive. I was considering buying a MBP with Retina, but was wondering how I would accomplish copying over my current hard drive to the retina, as I know you can't take out the retina's hard drive, and it is flash. Any suggestions?

    Connect the two with a Firewire cable if they both have Firewire ports (or use Thunderbolt if the both have Thunderbolt ports.) Boot the new computer into Target Disk Mode and the old computer normally. The new computer's disk drive should appear on the Desktop of the old computer.
    Clone using Restore Option of Disk Utility
      1. Open Disk Utility in the Utilities folder.
      2. Select the destination volume from the left side list.
      3. Click on the Restore tab in the DU main window.
      4. Select the destination volume from the left side list and drag it to the Destination
          entry field.
      5. Select the source volume from the left side list and drag it to the Source entry field.
      6. Double-check you got it right, then click on the Restore button.
    Destination means the new computer's drive Source means the old computer's drive.
    Be sure the old computer is running a version of Mountain Lion that is later than the version installed on the new computer. After cloning you will probably need to run the new 10.8.2 updater for the new computer. OS X Mountain Lion 10.8.2 Update for 13" Macbook Pro with Retina Display, 21.5" iMac (Late 2012), Mac mini (Late 2012).

  • How to replace hard drive on MacBook?

    I need to replace the hard drive on an older MacBook...how do I go about doing this?
    I'm pretty sure I just need to buy a new one, but don't know if it has to come from the Apple store.
    When I was last at Apple, they told me I could probably have it done at Best Buy.
    Please help...I'm not very computer savvy.

    You can find replacement drives plus installation tutorials at OWC.

  • Changing hard drive on macbook white

    i would like to know if changing the hard drive on the white macbook will remove the waranty ?
    i think changing it for a 320G 7200RPM western digital (scorpio)
    it's a 2.13G / 2G ram / 160G HD

    DMTY wrote:
    i would like to know if changing the hard drive on the white macbook will remove the waranty ?
    i think changing it for a 320G 7200RPM western digital (scorpio)
    it's a 2.13G / 2G ram / 160G HD
    The warranty should be intact should you change a hard drive and the installation is performed correctly. What isn't covered under warranty is a poor job, such as stripping screw threads or damaging a connector via improper insertion technique. Warranty terms may differ depending on country, but Apple has pretty standard terms that may be altered slightly depending on local laws.
    There are caveats. Apple would not be responsible for the new drive (or anything ever damaged by the new drive if it fails), although most aftermarket hard drives come with their own warranties. Some drives come with warranty terms with coverage for consequential damage. Fortunately hard drives almost never cause permanent damage of the host machine. but you should still read the warranty terms.

  • How to Upgrade Hard Drive in MacBook Pro?

    I made the mistake of getting only the 90G HD is a MBP purchased in Feb 2008. The manual does not have info on upgrading the HD and I suspect doing so myself may void the Apple Care warranty.
    Will the Apple Store do this upgrade for me and in a manner that would not void the warranty?
    Thanks,
    Marcantonio

    THe MacBook Pro you are speaking of has a hard drive that is not user replaceable. Meaning, it would void the AppleCare. With that said, any Apple Certified Support Center can service your MacBook Pro without voiding the warranty, this includes retail Apple Stores.
    http://www.apple.com/buy/locator/service/

  • How do change hard drive creation date on OS 10.3.9 hard drive

    Nuts, I installed my OS and configured everything without releasing that because the battery was dean the date had reverted back to 1976. Any way to change the hard drive creation date that shows up in GetInfo on my hard drive. Thanks

    Hi, Brett -
    That is often an effective solution, when OS 9 is available on another drive or machine, and all that is needed is the availability of Classic.
    Unlike OSX, an OS 9 System Folder can be copied via a Finder copy process (drag and drop) and still retain full functionality.
    However... if the receiving machine is OS 9 bootable, and the need is not only for Classic but also for a bootable OS 9 System Folder, copying such a folder from a different model Mac will rarely work. Unless specific steps are taken to perform a universal install of OS 9, an OS 9 install will be tailored to the machine it is installed upon - it will be model-specific to that machine.

  • HOW TO REPLACE HARD DRIVE WHITE MACBOOK EARLY 2009

    I have a White MacBook Early 2009, I need suggestions. My Macbook is still running fine, but would like to know which Hard Drive I should purchase as replacement. Thinking of going 500GB if possible, I already downloaded the instructions. Just trying to get my ducks in order for when that time comes, hopefully not for a few more years.

    For a new hard drive try Newegg.com  
    Regular SATA drives http://www.newegg.com/Store/SubCategory.aspx?SubCategory=380&name=Laptop-Hard-Dr ives&Order=PRICE  Use the list at the left for larger and faster drives.
    SSD drives
    http://www.newegg.com/Internal-SSD/SubCategory/ID-636?Order=PRICE  Use the list at the left for larger and faster drives.
    Or OWC for regular hard drives and SSDs  http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/
    Here are instructions on replacing the hard drive in a MacBook with a removable battery. http://creativemac.digitalmedianet.com/articles/viewarticle.jsp?id=45088
    To transfer your current hard drive I like the applications Carbon Copy Cloner or SuperDuper. They make a bootable copy of everything on your hard drive. http://www.bombich.com/index.html or http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html 
      You'll need a cheap SATA external hard drive case. Put the new drive in the case then format and partition the new drive and clone your old drive to the new one. Check that it's set up right by booting up from the external drive. Then replace your old hard drive with the new one and put your old one in the external case.
    Here's a cheap SATA external hard drive case on Amazon http://www.amazon.com/Vantec-NexStar-2-5-Inch-External-Enclosure/dp/B002JQNXZC/r ef=pd_cp_pc_0
      If you don’t have the tools to open up the MacBook OWC has a set for $5
    http://eshop.macsales.com/item/OWC/TOOLKITMHD/

  • How to change hard drive in 20" iMac G5 iSight ?

    I opened up the machine to replace a dead hard drive (warranty is over anyway) and discovered
    there is black tape that seals the edge of the display as well as the area below it. Can I remove this
    to change the drive and then put it back without detriment to the functionality of the machine?

    Here are the experiences of someone who did what you are doing:
    BulaRae posted this experience with the iSight:
    Remove all 5 screws on the bottom. The two for the ram slot are captive. The other 3 are not. One is longer than the others, note which slot it came from.
    There are catch levers on the top corners that need to be released by sliding something in there. That post recommended a credit card or thin plastic. I used two thin table knives with non-serrated edges.
    Once the top is off you can flip it up and lay it down or undo all the tape and unplug the iSight. I left mine intact.
    Then the fun part (NOT!). Using my table knife I very carefully peeled up the thick black foil tape stuff along the two edges. It's so sticky and tears easily. You need infinte patience. Once peeled up it reveals 4 torx screws holding the LCD in down on the bottom. You need a long Torx screwdriver and make sure it is magnetic—the screws are not captive and what a pain! Especially when you don't have a magnetic driver!
    The you can lift up the LCD. Again I left mine connected and just propped it up by sticking a can of compressed air I had sitting nearby in as a prop (obviously away from the boards). I did have to disconnect the video though (two white connectors on the left that are easy to disconnect). I later read that other connectors were very fragile in this model and wires rip easily, so I'm glad I didn't mess with any more than I had to.
    Once I got to the drive I discovered that the third connector (very small 4-pin that went off the side of the drive and over to the board in a different place than the bigger connectors) was too small for the drive that OWC sent me, so now I'm back together (but it ain't pretty in there anymore!) and calling OWC, only to have to do this again in another week or so.
    Moral of the story: don't try this at home, folks, unless you have infinite patience and love to do painstaking, tedious things, and also are really good at putting things back together the way you found them!

  • Got a new external hard drive. Transferred all files from old hard drive to new hard drive. Connected hard drive to macbook. How do I get all my files to be recognized by iTunes and my already made playlists??

    Got a new external hard drive. Transferred all files from old hard drive to new hard drive. Connected hard drive to macbook. How do I get all my files to be recognized by iTunes and my already made playlists??

    Trying to download photos from IPHONE, IPAD to IPHOTO in IMAC after installing new hard drive.
    How did you import the photos to iPad and iPhone?
    If the photos have been synced to the iPhone and iPad using iTunes, you cannot sync them back.
    See this document:  http://support.apple.com/kb/HT4236
    You can't reimport pictures synced from your computer to your device back to your computer. You can only import pictures in the Camera Roll or Saved Photos from your device to your computer. If you need to retrieve synced photos from your device:
    If your photos are not in the Camera Roll on your devices, save them to the Camera Roll, share them to the Photo Stream, mail the photos, or, if you have iPhoto on the devices, use iTunes Photo Sharing.
    http://help.apple.com/iphoto/iphone/2.0/?handbuch#blnkee26bc1
    Save photos to your computer using iTunes
    Connect your iOS device to your computer.
    Tap a photo, album, event, web journal, or slideshow and tap Share> iTunes.
    Tap Selected, or change the photos you want to save (if you are saving a slideshow skip to step 4):
    Select different photos: Tap Choose Photos, tap one or more photos, and tap Next.
    Select a range of photos: Tap Choose Photos, tap Range, tap the first and last photos in the range, and tap Next.
    Select all the photos in an album or event: Tap All.
    In iTunes, click the button for your device and click Apps at the top of the window.
    Below File Sharing, select iPhoto (in Apps).
    Select the Shared Photos folder under iPhoto Documents.
    Click Save To and select the location on your computer where you want to save the items.
    To view your photos, go to the Finder and look in the location you selected above.

  • I have a macbook pro md318 late 2011 i want to know can i change hard drive from 500GB to 2TB????

    i have a macbook pro md318 late 2011 i want to know can i change hard drive from 500GB to 2TB????

    Tbh,  I really wouldn't bother.
    I may get shot down here, but I like having storage centralised, backed up etc, so I would use the internal storage for the day to day stuff, and anything more dated, and large, then dump it on an external, with backup.
    I've heard some horror stories about larger capacity drives getting over hot, and failing in some machines. Not macs particularly though.

  • How to view windows Xp formatted hard drive with Macbook pro without losing data

    How to view Windows Xp programed Hard drive with Macbook pro with out losing data on hardrive

    Go to the First Aid tab in Disk Utility, select the external drive partition and read the format from the lower left, at the bottom.

  • I lost my logic 8 pro serial number. I can't find the booklet that comes with the serial number. How can retrieve this? I upgraded from logic pro 7. I changed hard drives and now it keeps asking for the serial number. But I can't find it. Where can I requ

    I lost my logic 8 pro serial number. I can't find the booklet that comes with the serial number. How can retrieve this? I upgraded from logic pro 7. I changed hard drives and now it keeps asking for the serial number. But I can't find it. Where can I request it? Thanks!

    If you still have the receipt or other proof of purchase, you can ask Apple to send you the serial. Otherwise, bad luck mate.. Good news is, you can now buy Logic Pro 9 from App Store for just 199 USD

  • How to upgrade my internal hard drive for macbook 5,2 from 160GB to 1TB?

    Hello,
    I wonder if you can please help me out.
    I wonder, is it possible to upgrade my internal hard drive for macbook 5,2 from 160GB to 1TB?
    Thanks,

    There's only one 9.5mm high 1tb drive around http://eshop.macsales.com/item/Samsung/HNM101MBB/
    With a video on replacing the hard drive http://eshop.macsales.com/installvideos/macbook_13_mem_hd/

  • Using Carbon Copy Cloner which is quicker firewire 800 Macbook Pro to external hard drive or Macbook Pro to same via Airport Extreme?

    Using Carbon Copy Cloner which is quicker firewire 800 Macbook Pro to external hard drive or Macbook Pro to same via Airport Extreme?

    Firewire 800 is the fastest and most reliable. Also it's bootable if you hold the option key down on a wired or built in keyboard.  Not bootable via Airport obviously or if Filevault is used.
    It's only your first clone that's usually takes the longest, it's shorter when it updates as you only do the changes which you can control to keep a pure clone if you wish.
    Most commonly used backup methods

Maybe you are looking for

  • Error: The Network Adapter could not establish the connection

    hi, i am using classes111.zip (the oracle 8.0.5 thin driver) with linux and gnu jsp pages. the backend is an oracle 8.04 NT database. i get this error: "The Network Adapter could not establish the connection " my question is this - is this error the

  • HT204368 No Bluetooth devises appear while IPhone is trying to detect, what's wrong ?

    No Bluetooth devises appear while IPhone is trying to detect, what's wrong ? In addition the Bluetooth sign on the upper part of the IPhone appears only when I enter the Bluetooth setting. Is this part of IOS 6.1 changes?

  • New security on 10.2.0.2

    I have a 3rd party product for QA that creates automatically all database objects. When I create users for testing I grant them only connect , resource, and unlimited tablespace. The tool was running until now with no problems on 10.1.0.4, but after

  • Changing Color Of Console Cursor

    I've searched for about five hours trying to uncover the method of changing the color of the console cursor in Linux. Specifically I'm not trying to change the color of the cursor in terminals, I know how to do that, but I don't know how change them

  • Trying to create detail in SOAPFaultException

    Hi I'm trying to generate the detail section for a SOAPFaultException (code snippet below) This compiles fine but when it runs I get the following exception try to access class javax.xml.soap.FactoryFinder from class javax.xml.soap.SOAPFactory // cod