How to change Ip address of Wireless network from telnet

Dear all
Please detail guide me change IP address of WLC and AP using telnet? What is fist change WLC or AP ?
Thanks

It would be better to understand what is the current IP address and vlan and what you are trying to change to. You can always telnet and ssh to the WLC and change the WLC IP address, but the IP address for the APs can be changed from the WLC GUI or CLI if the AP's are static. If the AP's are getting their IP address from dhcp, then you don't really have to do anything, just reboot the AP for the ap to get a new address. The reboot can be done from the WLC GUI or CLI or just be shutting down the PoE port or disconnecting the power injector from the unit if your using power injectors.
Sent from Cisco Technical Support iPhone App

Similar Messages

How to change ip address on EDGE network?

Hello.
I have a problem setting up the gprs settings.
Please help.
I want to use This settings.
općenite MMS postavke za TOMATO
APN; Pristupna točka: mms.tomato.com.hr
URL servera, Server URL, MMS centar; Početna stranica: http://mms.Tomato.com.hr/servlets/mms
IP adresa: 212.91.99.91
IP port: 8080
općenite GPRS postavke za TOMATO
APN: tomato
URL servera, Server URL, MMS centar; Početna stranica: http://m.tomato.com.hr
IP adresa: 212.91.99.95
IP port: 8080
The problem is i dont know how to change the ip address and port. I have to change it to have access to zero facebook.
Thank you.

Hi Pixus,
The NI-USRP Configuration Utility is what you need to change the IP address. Under the Change IP Address tab, select the device that you want to change. It will then auto populate the Selected IP Address section. Next, fill in the New IP Address field. Before you hit the Change IP Address button, click on your device again and verify that it is highlighted and blue like in this image:
After you have verified that your device is selected, hit the Change IP Address button. "Power cycle the device" means to turn the device off and then back on again. This allows the settings that you have changed in the device EEPROM to be set and the new settings will be recognized upon reboot.
Sarah Y
SDR Product Manager
National Instruments | Ettus Research

How can i set up a wireless network from my iMac lion, with a windows 7??

I wish to setup a network from my iMac to my gf windows 7 laptop, but can't figure out how...

In order to do this you should have a router. Once you have a router and both computers on the network then you will need to turn on File Sharing on the Mac. You can locate Sharing in System Preferences - Sharing. On the PC it has a similar function but typical of MS Windows much more arcane and complex. First thing you will need to know is what version of MS Windows you have, then you can Google something like "File sharing OS X Lion with Windows 7" and you will find lots of instructions.

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

Can anyone tell me how to change the names of the networks I have set up on Airport Express

Can anyone tell me how to change the names of the networks I have set up on Airport Express please? I now work in a UN compound and my network is my own name, would prefer some anonymity so seeking to change the wifi network name that others might see.

Hi mkl1961,
Happy Holidays! The article below will explain how to reset your Airport Express and change the network and base station names back to their defaults.
Resetting an AirPort base station FAQ - Apple Support
http://support.apple.com/en-us/HT3728
What default settings will my AirPort base station have after a hard or factory default reset?
AirPort base stations are set to request an IP address by DHCP.
AirPort base station passwords are "public."
AirPort base station names revert to "base station xxxxxx," where xxxxxx is the last six digits of the wireless MAC address*.
AirPort base station network names are "Apple Network xxxxxx," where xxxxxx is the last six digits of the wireless MAC address*.
*A MAC (Media Access Control) address, also known as a "network ID," is a unique hardware identification number for a network port. You can find the wireless and Ethernet network IDs on the printed label on the bottom or side of the device.
Airport Express Setup Guide
manuals.info.apple.com/MANUALS/1000/MA1613/en_US/airport_express_80211n_2nd_gen _setup_guide.pdf
I hope this information helps ....
- Judy

How can I delete a wireless network from my MacBoork Ai

How can I delete a wireless network from my MacBoork Air.
I had set up a WEP Network but I need to set up a WPA (personal) network now and i cant seem to change the WEP network to a WPA2 network.
Thank you for any help you can provide me.
LShaps

The MacBook Air will autodetect WEP and WPA security changes and should allow you to reconnect again. If the password stored in the Mac is wrong, it will ask you to enter it again.
With that said, to forget a network do the following:
- Go to the Apple Menu and select System Preferences
- Click on the Network icon
- Highlight the Airport / WiFi entry (sepending on 10.6 vs 10.7)
- Click the Advanced button at the bottom
- Make sue the Airport / WiFi tab is selected
- Click on the network name you want to forget
- Press the minus button at the bottom of the list.
You may also want to consider restarting if you are having this issue.

Netsh does not work to set IP address of "Wireless Network Connection"

On Windows 7 Professional
This set of commands work for configuring the "Local Area Connection"
netsh interface ip set address name="local area connection" static 74.94.87.157 255.255.255.248 74.94.87.158 1
netsh interface ip set dns name="local area connection" static 8.8.8.8
netsh interface ip add dns name="local area connection" 68.87.77.130 index=2
BUT for the WiFi connection, this command errors with this message "ELEMENT NOT FOUND"
netsh interface ip set address name="Wireless Network Connection" static 74.94.87.157 255.255.255.248 74.94.87.158 1
BUT the 2 following dns commands DO work for the Wifi Connection.
netsh interface ip set dns name="Wireless Network Connection" static 8.8.8.8
netsh interface ip add dns name="Wireless Network Connection" 68.87.77.130 index=2

I FOUND A SOLUTION
I manually renamed the interface from "Wireless Network Connection" to "Wifi"
Then when I use "WiFi" in the command line, I no longer get the
ELEMENT NOT FOUND error.
I have no idea why renaming the interface works . . as shown on original post above, "set dns name" command worked without the name change, but the "IP set Address" did not work.
Anybody know what this is about ?

How to change IP adress of wireless controller 2504 . from GUI

how to change IP adress of wireless controller 2504 . from GUI

In the existing setup, does WLC management & APs are on the same vlan ? If that is the case you may have not configured any of the below, as AP L3 broadcast reach WLC & in that way AP will learn about WLC.
If WLC & APs are on different vlan you may already use one of WLC discovery method listed below.
1. DHCP Option 43
2. DNS
3. UDP broadcast forwarding
4. Static configuration
When you change the WLC management IP address, AP need to know what is the new IP & you can modify the configuration of the method you used.
HTH
Rasika
**** Pls rate all useful responses ****

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages sometimes. How do I fix?

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.

If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue.

How to change mac address on mac

i'm sry i'm not sure if this is the right section or not but yeah.... nyways does anyone know how to change mac address on a macbook?

If you have not updated your OS you can use the following command.
sudo ifconfig enX ether xx:xx:xx:xx:xx:xx
You will need to replace the X with your network number and the xx:xx:xx:xx:xx:xx with the mac you want to have.
Then run
sudo ifconfig enX down
sudo ifconfig enX up
This change will last till your next reboot.
cheers
NOTE: This is not working in 10.5

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either.

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either. I have an iphone 4 that will not connect to 5ghz.
thank you!

Your AirPort Express is already providing two separate 2.4 GHz and 5 GHz bands, but each band is using the same wireless network name.
This is the default setup for the AirPort Express, which is recommended for most users. The theory here is that devices will automatically connect to the best quality signal based on their capabilities and distance in relation to the AirPort Express.
It is possible to assign a different name to the 5 GHz band, and then "point" devices at that network to connect. Some users swear by this option.....(I am not one of them).... but you might want to give it a try to see how it works for you.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Express
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options near the bottom of the next window
Enter a check mark next to 5 GHz Name.....which will automatically add "5 GHz" to the network name....so you can identify it
Click Save, then click Update and wait a full minute for the Express to restart
Now you will need to "point" your 5 GHz capable devices at the 5 GHz network name. 2.4 GHz devices will connect to your "other" network name.

I just purchased the airport Express to use in hotels while traveling to create a wireless network from the hotels wired dsl. A friend said to set up the network from home prior to traveling. How do I set this up? Thanks.

I just purchased the airport Express to use in hotels while traveling to create a wireless network from the hotels wired dsl. A friend said to set up the network from home prior to traveling. How do I set this up? Thanks.

In addition to RyanJC's comments, the 802.11n AirPort Express Base Station (AXn) can store up to five different http://docs.info.apple.com/article.html?artnum=108081 configuration profiles. You will need to use the AirPort Utility to create & save these profiles.
To create a new profile:
Open AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click "+" to create a new profile; give it a name, and then, click OK.
Set options, such as network name, passwords, Internet connection method, etc.
When done setting the options, click Update.
To switch profiles:
Open the AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click on the desired profile, and then, click OK to apply the new profile and restart the AX.
Just remember to switch to the desired configuration profile before removing power from the AX.

How to use LABVIEW to collect wireless network camera (with video server) video.

How to use LABVIEW to collect wireless network camera (with video server) video.I would like to use LABVIEW for a wireless network camera (IP Camera comes with the video server module)the client program.Will the ability to achieve?If feasible, how to do, there are examples, thank you.

I believe NI Vision is what you are looking for.

Does anyone know how to get an ipad to use the wireless network from an airport?

Does anyone know how to get an Ipad to use the wireless network from an airport express?

By default, the AirPort Express will broadcast an unsecure wireless network with a Network Name of something like: Apple Network NNNNNN. Your iPad should "see" this network and be able to connect to it. Have you tried going through the iPad's Settings > Wi-Fi > Choose a Network... option. If so, does the AirPort's wireless network appear in the list of available networks?
Can other wireless devices connect to the AirPort's network?

How to change Ip address of Wireless network from telnet

Similar Messages

Maybe you are looking for