How to: Change MAC adress on ps3 controller?

Hello.
I want to change my ps3 controllers MAC adress so that I can pair it to my android device.
There are instructions on this site: http://www.dancingpixelstudios.com/sixaxiscontroller/tool.html
"Command line utility version of 'sixpair' for OSX can be downloaded from here. Modified source code can be found here. This utility requires libusb, which can be downloaded from http://www.ellert.se/twain-sane/. Choose the binary for your version of OSX."
But I can't figure out how this works, so now I'm wondering if any of you either
1. can explain
2. know of an app that does this
3. has another way

I'm looking for an app that can fix this that runs on 10.8. I've seen other similar threads under respective osx version forum.
Do you have any suggestions which forum I could post it under if not here? I didn't really find a general forum.
/ Jonis

Similar Messages

How to change IP adress of wireless controller 2504 . from GUI

how to change IP adress of wireless controller 2504 . from GUI

In the existing setup, does WLC management & APs are on the same vlan ? If that is the case you may have not configured any of the below, as AP L3 broadcast reach WLC & in that way AP will learn about WLC.
If WLC & APs are on different vlan you may already use one of WLC discovery method listed below.
1. DHCP Option 43
2. DNS
3. UDP broadcast forwarding
4. Static configuration
When you change the WLC management IP address, AP need to know what is the new IP & you can modify the configuration of the method you used.
HTH
Rasika
**** Pls rate all useful responses ****

How to change mac address on mac

i'm sry i'm not sure if this is the right section or not but yeah.... nyways does anyone know how to change mac address on a macbook?

If you have not updated your OS you can use the following command.
sudo ifconfig enX ether xx:xx:xx:xx:xx:xx
You will need to replace the X with your network number and the xx:xx:xx:xx:xx:xx with the mac you want to have.
Then run
sudo ifconfig enX down
sudo ifconfig enX up
This change will last till your next reboot.
cheers
NOTE: This is not working in 10.5

How to change mac address on time capsule

Hi there,
How to change mac address on time capsule?

There are routers that allow you to create/clone a mac address to whatever you like. Since many companies use the mac address to 'register' a unit connected to it's system, you usually just have to let them know you've changed your router and they will reset your system to accept connections from the new device.

How to change mac address on wrt54g router

How to change mac address on wrt54g router?

are u sure u wanna change the MAC of the WRT54G ? it's not possible....you can however clone the MAC address of your PC onto the router...depending on your ISP.

How to Fetch MAC-Adresses across Subnets

Hi All,
for some reason we have a number of Machines out there where we would like to install a Package via ARD instead of Casper. We have a list of Hostnames from this Machines. Now, the first idea was to ping them and to get the MAC-Adress out of the ARP Cache via arp -a. All together could be used as an Import-File for Remote-Desktop.
But ARP does not work across Subnets.
Now i was wondering - how does for example ARD read the MAC-Adress from a Machine if i do a scan to a specific Network-Range. Could i use this process to fetch the MAC-Addresses? Or could there be another way.
bye
joe

Hi
You could try installing ARD on a client within that range? Poll workstations within that range for relevant information. Save it to the Desktop of that ARD workstation. Transfer it to a memory stick etc. Or if you know the IP address of that workstation you may be able to add it using the network address option from another workstation that's in a different subnet.
Tony

Solman how to change IP Adresses of servers

Hi,
we were using virtual ip adresses (other server names) for the database servers. These IP adresses (server names) does not exist any longer after changing the outsourcer. Now I want to change this values in SMSY, but exactly thist fiel is not accessible because the data source for this information is "SYSTEM RFC" does anybody know how to change this values?
I do not want to delete all the servers and reconnect them ...
Thank you.
Best regards,
Christian

Hello Christian,
If your data source is set to come from SLD - which should be for Solution Manager and Managed systems - the job LANDSCAPE FETCH is scheduled to run overnight and send the data from SLD to SMSY.
You can go to SM37 copy the job and release it for a instant update.
Best regards,
Guilherme Balbinot

How do i set up a PS3 controller with my mac?Before anyone says its not possible, it is, I've done it before but it now asks me for a passcode and i can't guess it and don't know it, please help

Before anyone says its not possible, as ive been told many times before, it is, I've done it before but it now asks me for a passcode and i can't guess it and don't know it, please help

if it keeps asking for the password again just write "0000", add the controller to your favorites, close bluetooth before asked for a password again, and the open bluetooth again

How to change Mac App Store Login for Updating Apps

I purchased a used Macbook from a local computer retailer; when they installed Mavericks and setup the account they used their Mac ID. Now it's showing updates for Keynote, Numbers, Pages, and iMovie but if I choose Update it prompts their username and wont let me change it. I assume those apps are connected to that account so it wont let me update. Is there a way to change the associated login to mine or is it safe for me to remove them and reinstall using my ID? I wasn't sure if they were core apps that would cause any damage if removed and I really dont want to format and start over. Thanks for the help!

The first thing to do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. How you do it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
It is not safe to use a computer with software installed by a previous owner.
1a. If you don't own another Mac
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for some MacBook Air models. For early MBA models, you may need a USB optical drive or Remote Disc. You should have received the media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
Some models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you may not be able to reinstall 10.6 even from the original discs, and Internet Recovery may not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
1b. If you do own another Mac
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
2. Partition and install OS X
If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In thePartition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
Then run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
3. Other issues
If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information.

How to change Mac Mavericks colors?

Hey
I have installed the new Mac Mavericks and it's nice but I wanna change the color of the bar up the one has the time and search and that things. It's green now maybe because of the Mavericks background but can I change the bar's colors only without the background?
Thanks!

You can't change the colour of the menu bar unless you use 3rd party utilities and /or hacks. As you rightly pointed out it is green because of the bacground image because it is set to be transculant:
Personally I do not like apps or hacks that alter the appearance of the OS. Not because I think it is perfect but because I am never certain they will not cause any trouble. Maybe I am getting old...
Still, if you insist: change the colour of os x menu bar

How to change mac desktop icons

I want to change my Macintosh HD icon to an icon of iMac. Where do I find this and do it?
I also want to change other HD icons on desktop - how is this done in Mavericks?
Thanks,
Don

Here are some cool icons:
#1:
http://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8& docid=K-Wt1TGwSJP-EM&tbnid=zkZ7DRuBycJmCM:&ved=0CAIQjBw&url=http%3A%2F%2Fsimplei con.com%2Fwp-content%2Fuploads%2Fimac.png&ei=ncdVU6TSMI_QsQS7mICwBg&bvm=bv.65177 938,d.b2I&psig=AFQjCNGn1t7gW_X0QFsVJnTTwBOnpqwkSg&ust=1398216982703961
#2:
http://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8& docid=RseTXyUI3pgvCM&tbnid=JjX8VdLRJggvuM:&ved=0CAIQjBw&url=http%3A%2F%2Ffiles.s ofticons.com%2Fdownload%2Fobject-icons%2Fmac-icons-by-iconshock%2Fpng%2F512%2Fim ac.png&ei=rcdVU5vcL83gsATI8ILYCQ&bvm=bv.65177938,d.b2I&psig=AFQjCNGn1t7gW_X0QFsV JnTTwBOnpqwkSg&ust=1398216982703961
They're in .png extention, you can convert them into .icn by a simple app like Img2icn or even use the online converter. Barney-15E answered the rest.

How to change MAC address on VPN Adapter - Deterministic Network Enhancer

Is it possible to change the MAC address 00-05-9A-3C-78-00 on the Cisco VPN Client / Cisco Systems VPN Adapter - Deterministic Enhancer Miniport. (Version 4.6.02.0011)
Thanks

I've tried using mac address changeing softeware on it before and it always changed it back when I enable my VPN.
HTH
Patrick

How to change Mac Login screen background?

I realize how to rename the four files "apple.png, apple_s1.png, [email protected], and [email protected]", in the Resources directory. But my picture keeps showing this grey bar at the bottom of the screen. I keep playing around with the resolution and it still shows. My macbook screen resolution is 1280x800. When I adjust the picture in "Preview", and change the height, it ends up cutting off the top of the picture but making the grey bar at the bottom smaller. Helps but it doesn't. Can you?

Hello,
Here you can see it in details:
http://application-express-blog.e-dba.com/?p=1681
http://www.grassroots-oracle.com/2011/07/modifying-your-apex-login-page.html
Regards,
Fateh

How i change mac os to windows

pls help me i cant install software

You can either utilize bootcamp and switch back and forth between Windows and Mac OSX or buy virtualization software such as VMWare Fusion or Parallels which allows you to run Windows without rebooting your Mac, this option is more convenient but doesn't offer as good of performance as bootcamp. Either option requires a full version of a Windows operating system (XP, Vista, 7).

How can i change my adress mail on iPhoto?

Can you tell me how to change my adress mail because i did a mistake in it and when i want to share my photos on hotmail they told me that my password and my adress are not compatible but i can't change it.. Please help me!

http://support.apple.com/kb/HE40

How to: Change MAC adress on ps3 controller?

Similar Messages

Maybe you are looking for