How to Change pacman Mirrors
arch works fine, except i use the ftp.archlinux mirror and its throttled, so my download are way slower then im capable. i followed this from the wiki
[core]
# Add your preferred servers here, they will be used first
Include = /etc/pacman.d/core
changed it to
[core]
ftp://ftp.nethat.com/pub/linux/archlinux/
Include = /etc/pacman.d/core
didnt work, tried
ftp://mirrors.unixheads.org/archlinux http a well
It wouldnt work, It even hung once so i had to restart.
So i cant figure out how to use other mirrors besides the default one and have them actally work. I would like to be able to download faster then 50-80kbps when im capable of mb's down at a time. I saw this in the wiki
"Aria2 Mirror Script " but it also says not to use ftp.arch linux with it, so im stuck, its all i can use. Any options for a newb?
maybe post a pacman.d if your in america? i dont know what im doing wrong.
shining wrote:
axion419 wrote:[core]
ftp://ftp.nethat.com/pub/linux/archlinux/
Include = /etc/pacman.d/core
It should read :
[core]
Server = ftp://ftp.nethat.com/pub/linux/archlinux/
Include = /etc/pacman.d/core
It should read:
[core]
Server = ftp://mirrors.unixheads.org/archlinux/core/os/i686/
Include = /etc/pacman.d/core
You need to specify the extra dirs, just like it does in /etc/pacman.d/core
Similar Messages
-
Guys, sorry if the answer is overly obvious, but I've spent a couple of days searching the forums, the wiki, google, and in the config files for how to change the sync timeout in pacman, but can't find what I'm looking for. Perhaps I'm using the wrong search terms, or looking in the wrong places, but not sure.
Anyway, when trying to sync the system with the package mirrors using pacman, there is currently a delay of what seems like 4 to 5 minutes for each mirror that is not available. I'm wanting to change that delay to something more like a minute or so if there's no problem in doing that.
Do any of you know where that timeout period can be changed?
Thank you.don't know if changing the timeout is possible, but delays to skip a non-responding mirror of more then 10 seconds are bad.
- how many mirrors do you have enabled and did you check them against http://www.archlinux.org/mirrors/status/
normally having 3 or 4 mirrors (1 primary, rest for backup) enabled is more then enough
- what Xfer command are you using ? -
How to change external display resolution WITHOUT clicking "CONFIRM"?
I have a somewhat unusual situation. My MacBook laptop is actually now a ModBook (a pen-tablet computer), and as such I no longer have a trackpad attached to it. All of my inputs are via the stylus, tapping directly on the built-in display.
This works perfectly fine, except when I need to give presentations on an LCD projector (which is quite often lately). I like to use the projector as an external monitor, so that I can run the Keynote presentation on it while using my laptop screen as the presenter's display, with the upcoming slide, etc. If the projector doesn't give me an ideal native display option (sometimes, the aspect ratio for the 3 or 4 resolutions available in the Displays drop-down in the menubar turn out to be stretched or squeezed), then I, naturally, have to open the Display System Preferences and try out different resolutions.
The problem is, since my stylus only interacts by clicking directly on the built-in-display, I have no way of moving the cursor over to the external display when the dialog box with the "Click here to confirm change/You have 15 seconds..." message appears. So I can never click it ... so I can never confirm the new settings.
The workarounds I've used so far are:
- Mirror displays (not ideal, as I need the presenter preview of the next slide)
- borrow a mouse from someone (usually from a Windows desktop, frankly) and plug that in to briefly mouse over and click the confirm button
I'd love to find a software workaround that allows me to NOT mirror displays and also doesn't require me to carry around a mouse all the time (my laptop bag is already overstuffed...).
Thanks.Fateh wrote:
I hope that my question is clear ... Nope.
How to change the display resolution of APEX ??APEX doesn't have a display resolution. "Display resolution" is an attribute of the device and user agent software used to view the APEX page.
What do you mean by "the display resolution of APEX"?
In other word, if an end user sees large elements on a pageWhat "large elements"?
then he/she zooms it outHow?
"Zooms" what—the entire page or a single "large element"?
How can I set a proper ZOOM for my app by default ...Meaning what?
And as usual, we're missing:
<li>Full APEX version
<li>Full DB/version/edition/host OS
<li>Web server architecture (EPG, OHS or APEX listener/host OS)
<li>Browser(s) and version(s) used
<li>Theme
<li>Template(s)
<li>Region/item type(s)
You've been posting here for years. You know this basic information is necessary to understand and reproduce problems.
If you're looking for help it doesn't seem unreasonable that you make the effort to provide a full, clear but concise description of the problem or requirement. -
How to disable airplay mirroring on iPad with ios7
How to disable airplay mirroring on iPad with ios7?
I've had this problem ever since I was at my friend's house- she has Apple TV- and my iPad connected automatically. So, I have no idea why any of the practical solutions that people think of are not options BUT, in terms of just getting it done, I did figure out a way. The key for me was getting near another Apple TV. I was out of town so I took my iPad to another friend's house who also has TV. Once I was logged onto their wireless network (the same network that their Apple TV is on-- that's how it connected in the first place), then the Airplay icon and options showed up from the bottom-draw menu and I was able to make sure that mirroring was turned off from the Apple TV section and to make sure the selection was on iPad instead. Problem solved. Now whether or not this will stay the same (rather than me having to make sure it stays at this setting everytime I link up to a network that has an Apple TV on it) I don't know. So my advice is find someone with Apple TV and connect to their network with your iPad and then change it.
-
when i change slide mirroring from off to on ,my new i pad lost wi fi connection and apple tv lost wifi connection:ihave last software for both.Can u help me?thanks.
when i use i pad with apple tv for see my photo,youtube and movies all ok.I suspect that the problem is in your router. Do NOT consider your router to be blameless if some other devices seem to work with it.
Try restarting your WiFi router by removing power for 30 seconds. Don't just turn it Off. On many routers that doesn't really do anything but put the router into standby mode. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
There is a chance that some services turned on in your router could be causing problems. Look for a setting called QoS (Quality of Service). If ON turn it OFF.
If you need more help please give the make, model, and version of your WiFi router and how you have it configured.
See also here: http://www.apple.com/support/ipad/wifi/ -
All the pacman mirrors seems to be slow from my location, chennai in southern India. The only reason I am sticking with ubuntu, is that they have got a mirror 4 kms away from my home in IIT and i get 60K download speed on my 512kbps line. I tried a few of them and none of them includeing the main server give more than 30k. This should'nt be a problem, except that my ISP has a download limit and I can download for free only for 11pm to 9am, which is usually used for downloading other stuff. So how do I find which server will be fastest for me. I tried to ping the servers and compare, but I soon discovered that the ping really does'nt influence download speed. Often a server with higher ping seems to be faster than some with lower ping.
Last edited by unixguru (2007-06-27 05:35:55)i use the apokryph server from the topic of #archlinux.de which is pretty up to date and i get good speed there aswell (about 650k). the downside is, that it doesn't include the community repo
edit: switched to hosteurope.de too. just as fast, more up to date than apokryph and it has community too /me happy
Last edited by baze (2007-04-07 15:51:50) -
Portege S100: How to change the RAID in the BIOS
Changing the BIOS setting for Portege S100 from JBOD to RAID0, I hit space on Exectute Creation and enter the string key in the manual and press "enter".
The settings then return to existing settings and not the new RAID0 setting I selected.
I have been at this most of the day / evening looking at various posts, but I can see nothing wrong with the details entered.
It is the same as recorded in this link:-
[How to Change the RAID configuration|http://aps2.toshiba-tro.de/kb0/TSB6901K60006R01.htm]
I am now at the end of my tether, I only wanted to install new WD HDD and do fresh install of XP Pro, is that too much to ask?Maybe its a silly question but; did you install the second HDD in the Ultra Slim Bay?
The RAID feature is ONLY available when a second HDDD is installed in the Ultra Slim Bay.
If the second HDD has been inserted then you could change the RAID in Windows OS.
There should be a Toshiba RAID Console.
You can use this console to create or manage a RAID array.
To start the utility click Start, point to All Programs, point to Toshiba, point to RIAD and click RAID console.
Its possible to change RAID1 (mirroring) from a non-RAID configuration (default).
But note; when RAID1 is set, you cannot change your settings unless you completely restore your preinstalled software. -
How to change default alerts in iCal?
Hello.
Every time you add a new event in iCal, the Info panel of the event contains a series of default alerts that you may want to add to it. However, all of them are useless to me (e.g.: "Send email to <my address> 4 days after), so I need to manually edit them event by event. Anybody knows how to change them? I have already inspected all the plist files related to ical, and looked inside the ical package content, but I found no indication of where to change these values. Using iCal version 5.0.2
Thanks,
lJohn: Thank you, this is exactly what I wanted. I was indeed inspecting the plist with bbedit, but what I did not realize is that the file has some parts which are binary, so I could not see the PersistentMenu-lastUsedAlarms part by using a text editor. I opened it with Xcode and I did find what you were saying, and erased all the junk that was in there. In fact, the issue I had was also described here:
http://newsgroups.derkeiler.com/Archive/Uk/uk.comp.sys.mac/2010-06/msg02349.html
For some reason, it looks like after some upgrade the program adds were some positive values in the plist and I was stuck with default alarms that were set *after* the events I wanted to set an alarm for.
I did what you suggested, then added by hand new values to the PersistentMenu part of the plist, and I am now happy.
For everybody's information, to know what I did, it is enough to know to add Dictionary items to the PersistentMenu-lastUsedAlarms, with 3 fields:
-- AlarmTypeKey (this determines if you want a sound, or else an email, or else the other default alarm type keys. For example, sending an email is a Number, value 4; having a message with sound is a Number, value 3)
-- AlarmDurationKey: This is a Number, in seconds, that determines when you want your alarm to trigger. E.g: -172800 will be two days before. Must be negative for "before", of course)
-- AlarmParameterKey: This is a String, where you store the value that you want the alarm to have. For example, if you want an email to be sent, the AlarmTypeKey will be 4, as explained above, and this field will contain your email address. Instead, if you want the alarm to be a sound, the AlarmTypeKey will be 3 and this field will have the name of the sound you want (e.g., Basso).
That's it. Thanks a lot for the solution!
l. -
How to change pricing Conditions in Sales order in change sales order bapi
Hi Experts,
How to change pricing Conditions in Sales order in change sales order bapi.
I have used the 2 function modules bapi-changesalesorder and sd salesdocument change, But it is creating the new record , instead of changing the existing one, Could please assist regarding the same
Thanks in Advance .
NLNHI NLN
I have just tried on my system and managed to overwrite the existing price by passing the following parameters.
<b>Import Paramters:</b>
SALESDOCUMENT - Sales Document Number
ORDER_HEADER_INX - UPDATEFLAG as <b>'U'</b>.
LOGIC_SWITCH - Import Structure - Pass 'X' to LOGIC_SWITCH-COND_HANDL.
<b>Tables:</b>
CONDITIONS_IN - ITM_NUMBER,
COND_COUNT, -> Condition counter same as KONV-ZAEHK generally it is <b>'01'</b>
COND_TYPE,
COND_VALUE,
CURRENCY.
CONDITIONS_INX - ITM_NUMBER,
COND_COUNT,
COND_TYPE,
UPDATEFLAG as <b>'U'</b>,
CURRENCY.
Hope i have clarified your query.
Kind Regards
Eswar -
Hi Support team, somehow my mozilla settings have been changed and it became transparent, now how to change back to normal because everything is transparent, menus, pages etc.
This could be the same problem other users are reporting as a white screen or black screen, caused by an incompatibility between Firefox 33 and some older graphics card/chipset drivers.
Please disable hardware acceleration as a temporary workaround. Step-by-step directions in this thread: https://support.mozilla.org/questions/1025438
Does that work? -
How to change header and footer in login page in oracle apps r12
Hi all,
how to change header and footer in login page in oracle apps r12 and login button background color, please help me
thanks
saranhow to change header and footer in login page in oracle apps r12 and login button background color, please help meTips For Personalizing The E-Business Suite R12 Login Page (MainLoginPG) [ID 741459.1]
How to Personalize Login page in R12? [ID 579917.1]
R12 Login Page: How to Personalize the Logo ? [ID 849752.1]
Thanks,
Hussein -
How to change the OraSSO login link in webcache/load balance
Hi
we have 10gAsR1 installed as a Portal instance. We have 6-server
load balancer => webcache as loadbalancer (listening port 80)
Wb ch1 and wb ch2 => webcache (listening port 7777)
portal1 and portal2 => Portal listening 7778
infra =>Infrastruture with repository Portal/Oracle SSO (listening 7777)
This set up is working fine for our intranet setup, now we need to open this for couple of external clients. Well initially we need to open on the load balancer server on port 80 for external team to access, it works fine when we make it publc access.
Now when we need to make it SSO (siteminder) enables, when users click on login link it first goes oracle sso then it internally redirects the page to site minder sso.
Well, I have noted that the sso server details are mentioned in global setting sso/oid details. Since we need to open this for external client we have to add a DNS entry for this so that we can allow its access over firewall..
Now I have made DNS name change at my infrserver level, now I need to update the change at the load balancer server (where wheb chache is running).
Any one know how to chang the URL at load balancer.
I am struck at this point please suggest how should i proceed..
Thanks,Extract from Personalization Guide - Page Footer - Personalization Considerations
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a standard Copyright and Privacy (that is, its Auto Footer property is set to true), set the Scope to OA Footer, in the Choose Personalization Context page of the Personalization UI.
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a custom Copyright and Privacy (that is, its Auto Footer property is set to false), set the Scope to Page in the Choose Personalization Context page of the Personalization UI. In the following Page Hierarchy Personalization page , identify and personalize the Privacy page element. -
How to change the privacy statement link url
I looked into the previous threads , could not find the answer to "Changing the privacy statement url to clients privacy statement url".
I am talking about the privacy statement URL in the page that user see it as soon as user logs into the e-business suite.
I have read the previous theads and developers guide regading how to show or hide this autofooter thing. but could not find any thing about how to change the one in the login page.I even looked ino personalization but could not find a place to change this url. please HELP.
Another question is " is it ok to show privacy statement in just the first page and hide it in rest of the application pages?"
Thanks
karanExtract from Personalization Guide - Page Footer - Personalization Considerations
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a standard Copyright and Privacy (that is, its Auto Footer property is set to true), set the Scope to OA Footer, in the Choose Personalization Context page of the Personalization UI.
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a custom Copyright and Privacy (that is, its Auto Footer property is set to false), set the Scope to Page in the Choose Personalization Context page of the Personalization UI. In the following Page Hierarchy Personalization page , identify and personalize the Privacy page element. -
How to change the default apex port
hi,
i am installed apex4.0 in EBS R12 DB with HTTP Server method. my apex is running from application server 10g and default port is 7777.
URl: http://hostname:7777/pls/apex
My EBS R12 running on http://hostname:8007.
is it possible to change the apex port to EBS Apache port(8007) in R12 and finally i want to change above URL like this
Before change : http://hostname:7777/pls/apex
After Change : http://hostname:8007/pls/apex
Thanks in advanace....How to Change the Default SSH Port from Terminal ?
now showing default SSH Port 22 i need change it pls help me how can do -
How to change CUE ip address?
Hi,
We moved to a new location and using comcast as ISP. I was setting up the phone system today and met a few problems.
1. First of all, all the phones are connected and working(total of 4), but I can only see 3 of them showing up in the CCA. Whats happening here?
2. I wanted to change the user name which appears on the phone using the CCA, CCA told me that the settings were successfully sent to UC520, I restarted the phone and uc520, but the names on the phones remain unchanged?
3. I forgot the password of the voicemail for one of the phone, and wanted to changed in the CUE. so I went to 10.1.10.1,but some comcast login page showed up instead of CUE. so I want to know how to change the IP address of CUE? I don`t know the CLI commands so please teach me if it can only be done with CLI. I have only used CCA in the past. Could this be the reason why for problem 1 and 2? I`m feeling wierd because all the phones can be used to call in/out.
my data vlan is 192.168.0.0 and voice vlan is 192.168.2.0 let me know if you need any other info.
need help urgently as I want to resolve this problem asap.
Thanks in advance.
Building configuration...
Current configuration : 31483 bytes
! Last configuration change at 19:39:02 EST Mon Jan 27 2014 by admin
version 15.1
parser config cache interface
no service pad
no service timestamps debug uptime
service timestamps log datetime msec
service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC_520
boot-start-marker
boot-end-marker
no logging buffered
no logging rate-limit
enable secret 4 X4ZqtPJ///KxuEWxHSsJrv3beQVnz2ise/xj8fF6eFU
aaa new-model
aaa authentication login default local
aaa session-id common
clock timezone EST -5 0
clock summer-time EDT recurring
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3885458945
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3885458945
revocation-check none
rsakeypair TP-self-signed-3885458945
crypto pki certificate chain TP-self-signed-3885458945
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33383835 34353839 3435301E 170D3133 30383136 32303534
32305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 38383534
35383934 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100E470 89FBE9D2 67ED2223 338A6991 0CF59918 BDEF6020 545DFCAF 93A17C39
BEE49E0E 4EDEE26B CCE65E3E 44443BFC E1CE6B5E FE8906DA 3290C015 450721F3
8FB997D1 74A9EAD1 2FB11EAF 7E346F69 4AF873DE A93DCCC0 0607406E 09C0D5D4
47552B50 34398AF9 A5F9CC57 1A2CBCE8 D8DCE2E9 6702F3DD 77505122 2284BDC8
96730203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14F3FB0C E861F89C 588B7B22 97DCB6B8 95F52EAF 3F301D06
03551D0E 04160414 F3FB0CE8 61F89C58 8B7B2297 DCB6B895 F52EAF3F 300D0609
2A864886 F70D0101 05050003 81810067 7B14BD34 CF6FE9A5 C2B125A9 347023AD
58DAB6CB E64FA260 41DA2B0B 1921A21D BAED2A0F 47172233 A589F64D 74D70BB5
2790DE19 B905BCFF 18DB2EE5 F397C92D 7522DEB0 B4968E27 0F2CCF98 DCCE40C5
4BF1736A 1C945AFA E0EF7A33 E529F94C CC99549A 051CA1BD E33495DB 0B79451C
5666954E 10E691DF 5D5CCC50 CB72D2
quit
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 192.168.0.1 192.168.0.99
ip dhcp excluded-address 192.168.0.151 192.168.0.255
ip dhcp excluded-address 192.168.2.1 192.168.2.9
ip dhcp excluded-address 192.168.2.241 192.168.2.255
ip dhcp excluded-address 192.168.2.99
ip dhcp pool phone
network 192.168.2.0 255.255.255.0
default-router 192.168.2.99
option 150 ip 192.168.2.99
ip name-server 205.152.111.23
ip name-server 205.152.144.23
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
voice class cause-code 1
no-circuit
voice register global
mode cme
source-address 192.168.2.99 port 5060
max-dn 88
max-pool 22
load 9971 sip9971.9-2-2
load 9951 sip9951.9-2-2
load 8961 sip8961.9-2-2
timezone 12
create profile sync 0423457390373118
voice hunt-group 1 parallel
final 201
list 201,223,227,239,301
timeout 16
pilot 511
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1112
rule 1 /^9/ //
voice translation-rule 2001
voice translation-rule 2002
rule 1 /^6/ //
voice translation-rule 2222
rule 1 /^91900......./ //
rule 2 /^91976......./ //
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile XFER_TO_VM_PROFILE
translate redirect-called 2002
voice translation-profile nondialable
translate called 1000
voice-card 0
fax interface-type fax-mail
license udi pid UC520W-16U-4FXO-K9 sn FTX1251Y0DC
archive
log config
logging enable
logging size 600
hidekeys
username admin privilege 15 secret 4 X4ZqtPJ///KxuEWxHSsJrv3beQVnz2ise/xj8fF6eFU
ip tftp source-interface Loopback0
class-map match-all _class_Voice0
match ip dscp ef
class-map match-all _class_Voice1
match ip dscp cs3
policy-map Voice
class _class_Voice0
set cos 6
class _class_Voice1
set cos 3
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $ETH-WAN$
no ip address
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/8
switchport mode trunk
switchport voice vlan 100
no ip address
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
antenna receive right
antenna transmit right
service-policy output Voice
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
ip access-group 109 in
ip mtu 1452
ip nat outside
ip inspect SDM_LOW out
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [email protected]
ppp chap password 7 121D001B1E535E56
ppp pap sent-username [email protected] password 7 121D001B1E535E56
ppp ipcp dns request
interface BVI1
ip address 192.168.0.55 255.255.255.0
ip access-group 104 in
ip access-group 108 out
ip helper-address 192.168.0.99
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
interface BVI100
description $FW_INSIDE$
ip address 192.168.2.99 255.255.255.0
ip access-group 102 in
ip access-group 107 out
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 192.168.0.99
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.1.1.0 0.0.0.255
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 permit ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 192.168.2.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 192.168.2.0 0.0.0.255 eq 2000 any
access-list 101 permit ip 192.168.2.0 0.0.0.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 102 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 102 permit ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 103 remark SDM_ACL Category=64
access-list 103 permit ip any any
access-list 104 remark SDM_ACL Category=64
access-list 104 permit ip any any
access-list 105 remark SDM_ACL Category=64
access-list 105 permit ip any any
access-list 106 remark SDM_ACL Category=64
access-list 106 permit ip any any
access-list 107 remark SDM_ACL Category=64
access-list 107 permit ip any any
access-list 108 remark SDM_ACL Category=64
access-list 108 permit ip any any
access-list 109 remark auto generated by SDM firewall configuration##NO_ACES_14##
access-list 109 remark SDM_ACL Category=1
access-list 109 permit ip 10.1.10.0 0.0.0.3 any
access-list 109 permit ip 192.168.2.0 0.0.0.255 any
access-list 109 permit udp host 205.152.111.23 eq domain any
access-list 109 permit udp host 205.152.144.23 eq domain any
access-list 109 permit icmp any any echo-reply
access-list 109 permit icmp any any time-exceeded
access-list 109 permit icmp any any unreachable
access-list 109 permit ip 10.0.0.0 0.255.255.255 any
access-list 109 deny ip 172.16.0.0 0.15.255.255 any
access-list 109 permit ip 192.168.0.0 0.0.255.255 any
access-list 109 deny ip 127.0.0.0 0.255.255.255 any
access-list 109 deny ip host 255.255.255.255 any
access-list 109 permit ip host 0.0.0.0 any
access-list 109 permit ip any any
dialer-list 1 protocol ip permit
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/7916/B016-1-0-4.SBN alias B016-1-0-4.SBN
tftp-server flash:/phones/7937/apps37sccp.1-4-4-0.bin alias apps37sccp.1-4-4-0.bin
tftp-server flash:/phones/7940_7960/P00308010200.bin alias P00308010200.bin
tftp-server flash:/phones/7940_7960/P00308010200.loads alias P00308010200.loads
tftp-server flash:/phones/7940_7960/P00308010200.sb2 alias P00308010200.sb2
tftp-server flash:/phones/7940_7960/P00308010200.sbn alias P00308010200.sbn
tftp-server flash:/phones/7941_7961/apps41.9-1-1TH1-16.sbn alias apps41.9-1-1TH1-16.sbn
tftp-server flash:/phones/7941_7961/cnu41.9-1-1TH1-16.sbn alias cnu41.9-1-1TH1-16.sbn
tftp-server flash:/phones/7941_7961/cvm41sccp.9-1-1TH1-16.sbn alias cvm41sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7941_7961/dsp41.9-1-1TH1-16.sbn alias dsp41.9-1-1TH1-16.sbn
tftp-server flash:/phones/7941_7961/jar41sccp.9-1-1TH1-16.sbn alias jar41sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7941_7961/SCCP41.9-1-1SR1S.loads alias SCCP41.9-1-1SR1S.loads
tftp-server flash:/phones/7941_7961/term41.default.loads alias term41.default.loads
tftp-server flash:/phones/7941_7961/term61.default.loads alias term61.default.loads
tftp-server flash:/phones/7942_7962/apps42.9-1-1TH1-16.sbn alias apps42.9-1-1TH1-16.sbn
tftp-server flash:/phones/7942_7962/cnu42.9-1-1TH1-16.sbn alias cnu42.9-1-1TH1-16.sbn
tftp-server flash:/phones/7942_7962/cvm42sccp.9-1-1TH1-16.sbn alias cvm42sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7942_7962/dsp42.9-1-1TH1-16.sbn alias dsp42.9-1-1TH1-16.sbn
tftp-server flash:/phones/7942_7962/jar42sccp.9-1-1TH1-16.sbn alias jar42sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7942_7962/SCCP42.9-1-1SR1S.loads alias SCCP42.9-1-1SR1S.loads
tftp-server flash:/phones/7942_7962/term42.default.loads alias term42.default.loads
tftp-server flash:/phones/7942_7962/term62.default.loads alias term62.default.loads
tftp-server flash:/phones/7945_7965/apps45.9-1-1TH1-16.sbn alias apps45.9-1-1TH1-16.sbn
tftp-server flash:/phones/7945_7965/cnu45.9-1-1TH1-16.sbn alias cnu45.9-1-1TH1-16.sbn
tftp-server flash:/phones/7945_7965/cvm45sccp.9-1-1TH1-16.sbn alias cvm45sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7945_7965/dsp45.9-1-1TH1-16.sbn alias dsp45.9-1-1TH1-16.sbn
tftp-server flash:/phones/7945_7965/jar45sccp.9-1-1TH1-16.sbn alias jar45sccp.9-1-1TH1-16.sbn
tftp-server flash:/phones/7945_7965/SCCP45.9-1-1SR1S.loads alias SCCP45.9-1-1SR1S.loads
tftp-server flash:/phones/7945_7965/term45.default.loads alias term45.default.loads
tftp-server flash:/phones/7945_7965/term65.default.loads alias term65.default.loads
tftp-server flash:/ringtones/Analog1.raw alias Analog1.raw
tftp-server flash:/ringtones/Analog2.raw alias Analog2.raw
tftp-server flash:/ringtones/AreYouThere.raw alias AreYouThere.raw
tftp-server flash:/ringtones/DistinctiveRingList.xml alias DistinctiveRingList.xml
tftp-server flash:/ringtones/RingList.xml alias RingList.xml
tftp-server flash:/ringtones/AreYouThereF.raw alias AreYouThereF.raw
tftp-server flash:/ringtones/Bass.raw alias Bass.raw
tftp-server flash:/ringtones/CallBack.raw alias CallBack.raw
tftp-server flash:/ringtones/Chime.raw alias Chime.raw
tftp-server flash:/ringtones/Classic1.raw alias Classic1.raw
tftp-server flash:/ringtones/Classic2.raw alias Classic2.raw
tftp-server flash:/ringtones/ClockShop.raw alias ClockShop.raw
tftp-server flash:/ringtones/Drums1.raw alias Drums1.raw
tftp-server flash:/ringtones/Drums2.raw alias Drums2.raw
tftp-server flash:/ringtones/FilmScore.raw alias FilmScore.raw
tftp-server flash:/ringtones/HarpSynth.raw alias HarpSynth.raw
tftp-server flash:/ringtones/Jamaica.raw alias Jamaica.raw
tftp-server flash:/ringtones/KotoEffect.raw alias KotoEffect.raw
tftp-server flash:/ringtones/MusicBox.raw alias MusicBox.raw
tftp-server flash:/ringtones/Piano1.raw alias Piano1.raw
tftp-server flash:/ringtones/Piano2.raw alias Piano2.raw
tftp-server flash:/ringtones/Pop.raw alias Pop.raw
tftp-server flash:/ringtones/Pulse1.raw alias Pulse1.raw
tftp-server flash:/ringtones/Ring1.raw alias Ring1.raw
tftp-server flash:/ringtones/Ring2.raw alias Ring2.raw
tftp-server flash:/ringtones/Ring3.raw alias Ring3.raw
tftp-server flash:/ringtones/Ring4.raw alias Ring4.raw
tftp-server flash:/ringtones/Ring5.raw alias Ring5.raw
tftp-server flash:/ringtones/Ring6.raw alias Ring6.raw
tftp-server flash:/ringtones/Ring7.raw alias Ring7.raw
tftp-server flash:/ringtones/Sax1.raw alias Sax1.raw
tftp-server flash:/ringtones/Sax2.raw alias Sax2.raw
tftp-server flash:/ringtones/Vibe.raw alias Vibe.raw
tftp-server flash:/Desktops/CampusNight.png
tftp-server flash:/Desktops/TN-CampusNight.png
tftp-server flash:/Desktops/CiscoFountain.png
tftp-server flash:/Desktops/TN-CiscoFountain.png
tftp-server flash:/Desktops/CiscoLogo.png
tftp-server flash:/Desktops/TN-CiscoLogo.png
tftp-server flash:/Desktops/Fountain.png
tftp-server flash:/Desktops/TN-Fountain.png
tftp-server flash:/Desktops/MorroRock.png
tftp-server flash:/Desktops/TN-MorroRock.png
tftp-server flash:/Desktops/NantucketFlowers.png
tftp-server flash:/Desktops/TN-NantucketFlowers.png
tftp-server flash:Desktops/320x212x16/List.xml
tftp-server flash:Desktops/320x212x12/List.xml
tftp-server flash:Desktops/320x216x16/List.xml
tftp-server flash:/bacdprompts/en_bacd_allagentsbusy.au alias en_bacd_allagentsbusy.au
tftp-server flash:/bacdprompts/en_bacd_disconnect.au alias en_bacd_disconnect.au
tftp-server flash:/bacdprompts/en_bacd_enter_dest.au alias en_bacd_enter_dest.au
tftp-server flash:/bacdprompts/en_bacd_invalidoption.au alias en_bacd_invalidoption.au
tftp-server flash:/bacdprompts/en_bacd_music_on_hold.au alias en_bacd_music_on_hold.au
tftp-server flash:/bacdprompts/en_bacd_options_menu.au alias en_bacd_options_menu.au
tftp-server flash:/bacdprompts/en_bacd_welcome.au alias en_bacd_welcome.au
tftp-server flash:/bacdprompts/en_bacd_xferto_operator.au alias en_bacd_xferto_operator.au
radius-server attribute 31 send nas-port-detail
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
shutdown
caller-id enable
voice-port 0/0/1
shutdown
caller-id enable
voice-port 0/0/2
shutdown
caller-id enable
voice-port 0/0/3
shutdown
caller-id enable
voice-port 0/1/0
trunk-group ALL_FXO 64
connection plar 201
shutdown
caller-id enable
voice-port 0/1/1
trunk-group ALL_FXO 64
connection plar opx 511
description Configured by CCA 4 FXO-0/1/1-Custom-BG
caller-id enable
voice-port 0/1/2
trunk-group ALL_FXO 64
connection plar opx 511
description Configured by CCA 4 FXO-0/1/2-Custom-BG
caller-id enable
voice-port 0/1/3
trunk-group ALL_FXO 64
connection plar 204
shutdown
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 192.168.2.99 identifier 1 version 3.1
sccp
sccp ccm group 1
associate ccm 1 priority 1
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 6 pots
description 鬰atch all dial peer for BRI/PRI�
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
translation-profile outgoing XFER_TO_VM_PROFILE
destination-pattern 396
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 2001 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 398
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 2012 voip
description ** cue prompt manager number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 240
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 58 pots
trunkgroup ALL_FXO
corlist outgoing call-emergency
description **CCA*North American-7-Digit*Emergency**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9911
forward-digits all
no sip-register
dial-peer voice 59 pots
trunkgroup ALL_FXO
corlist outgoing call-emergency
description **CCA*North American-7-Digit*Emergency**
preference 5
destination-pattern 911
forward-digits all
no sip-register
dial-peer voice 60 pots
trunkgroup ALL_FXO
corlist outgoing call-local
description **CCA*North American-7-Digit*10-Digit Local**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9[2-9].........
forward-digits all
no sip-register
dial-peer voice 61 pots
trunkgroup ALL_FXO
corlist outgoing call-local
description **CCA*North American-7-Digit*Service Numbers**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9[2-9]11
forward-digits all
no sip-register
dial-peer voice 62 pots
trunkgroup ALL_FXO
corlist outgoing call-national
description **CCA*North American-7-Digit*Long Distance**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91[2-9]..[2-9]......
forward-digits all
no sip-register
dial-peer voice 63 pots
trunkgroup ALL_FXO
corlist outgoing call-international
description **CCA*North American-7-Digit*International**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9011T
forward-digits all
no sip-register
dial-peer voice 64 pots
trunkgroup ALL_FXO
corlist outgoing call-toll-free
description **CCA*North American-7-Digit*Toll-Free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91800.......
forward-digits all
no sip-register
dial-peer voice 65 pots
trunkgroup ALL_FXO
corlist outgoing call-toll-free
description **CCA*North American-7-Digit*Toll-Free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91888.......
forward-digits all
no sip-register
dial-peer voice 66 pots
trunkgroup ALL_FXO
corlist outgoing call-toll-free
description **CCA*North American-7-Digit*Toll-Free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91877.......
forward-digits all
no sip-register
dial-peer voice 67 pots
trunkgroup ALL_FXO
corlist outgoing call-toll-free
description **CCA*North American-7-Digit*Toll-Free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91866.......
forward-digits all
no sip-register
dial-peer voice 68 pots
trunkgroup ALL_FXO
corlist outgoing call-toll-free
description **CCA*North American-7-Digit*Toll-Free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 91855.......
forward-digits all
no sip-register
no dial-peer outbound status-check pots
telephony-service
video
authentication credential admin admin
fxo hook-flash
max-ephones 22
max-dn 88
ip source-address 192.168.2.99 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service phone SPA525-wifi-on yes
service phone SPA525-protocol SPCP
service phone SPA525-auto-detect-sccp yes
service phone SPA525-http-write yes
service phone SPA525-SSID cisco-voice
service phone SPA525-readonly no
service phone SPA525-Encryption-type DISABLE
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message ZFI Engi & Const
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
cnf-file location flash:
cnf-file perphone
load 7916-12 B016-1-0-4
load 7916-24 B016-1-0-4
load 7937 apps37sccp.1-4-4-0
load 7960-7940 P00308010200
load 7941 SCCP41.9-1-1SR1S
load 7941GE SCCP41.9-1-1SR1S
load 7942 SCCP42.9-1-1SR1S
load 7945 SCCP45.9-1-1SR1S
load 7961 SCCP41.9-1-1SR1S
load 7961GE SCCP41.9-1-1SR1S
load 7962 SCCP42.9-1-1SR1S
load 7965 SCCP45.9-1-1SR1S
load 521G-524G cp524g-8-1-17
time-zone 12
keepalive 30 auxiliary 4
voicemail 396
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$AJGT$FDYMK5h1/Tiz2VQKQe2fS.
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
transfer-pattern 6... blind
secondary-dialtone 9
night-service day Sun 00:00 23:59
night-service day Mon 17:00 08:00
night-service day Tue 17:00 08:00
night-service day Wed 17:00 08:00
night-service day Thu 17:00 08:00
night-service day Fri 17:00 08:00
night-service day Sat 00:00 23:59
night-service date Jan 1 00:00 23:59
night-service date Nov 25 00:00 23:59
night-service date Dec 25 00:00 23:59
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 15
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 16
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer TrnsfVM Confrn Acct Park
ephone-template 17
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer TrnsfVM Confrn Acct Park
ephone-template 18
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-dn 9
number BCD no-reg primary
description MoH
moh out-call ABC
ephone-dn 81 octo-line
number 301 no-reg primary
pickup-group 1
name wpb wpb
call-forward busy 396
call-forward noan 396 timeout 20
ephone-dn 82 octo-line
number 227 no-reg primary
pickup-group 1
name Robert Stewart
call-forward busy 396
call-forward noan 396 timeout 20
ephone-dn 83 octo-line
number 239 no-reg primary
pickup-group 1
name Conf Room
call-forward busy 396
call-forward noan 396 timeout 20
ephone-dn 84 octo-line
number 223 no-reg primary
pickup-group 1
label 223
description George Guo
name Caroline Wang
call-forward busy 396
call-forward noan 396 timeout 20
ephone-dn 85 octo-line
ring external
number 201 no-reg primary
pickup-group 1
label 201
description Caroline Wang
name Cari Adamonis
call-forward busy 396
call-forward noan 396 timeout 20
ephone-dn 86
number 6... no-reg primary
description ***CCA XFER TO VM EXTENSION***
call-forward all 396
ephone-dn 87
number A801... no-reg primary
mwi off
ephone-dn 88
number A800... no-reg primary
mwi on
ephone 1
device-security-mode none
mac-address 0015.6276.7240
ephone-template 16
username "mdeng" password 123456
type 7940
button 1:82
ephone 2
device-security-mode none
mac-address 0015.6278.9118
ephone-template 16
username "jespinal" password 123456
type 7940
button 1:83
ephone 3
device-security-mode none
mac-address 0015.6269.5B0C
ephone-template 16
username "wpb" password 123456
mtp
type 7940
button 1:81
ephone 5
device-security-mode none
mac-address 0012.4362.0B1E
ephone-template 16
username "GGuo" password 123456
type 7940
button 1:84
ephone 6
device-security-mode none
mac-address 0015.6286.AE4F
ephone-template 16
username "cwang" password 123456
type 7940
missed-calls all
button 1:85
alias exec cca_voice_mode PBX
alias exec cca_vm_notification schedule from_time=00 to_time=24
banner login ^Cbanner login ^Cisco Configuration Assistant. Version: 3.2 (3). Sat Aug 24 11:52:57 EDT 2013^^C
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
transport preferred none
transport input all
line vty 5 100
transport preferred none
transport input all
ntp master
endhow to change local ip address?Via an operating system command.
It's not the sort of thing an application should be doing at all. IP addresses these days are assigned via DHCP. Why would you want to change it from within an application? It would probably disconnect all sockets for all running applications, invalidate the login, all kinds of bad effects.
What is the actual requirement?
Maybe you are looking for
-
Error message when logging into imessage and facetime
When I try logging into facetime and imessage on my ipod touch 4th gen, I get the following error message "the user name or password for "my email address" was incorrect. Try again." However I am able to log into apple id online, app store, game cent
-
Encountering errors in File scenarios
Hi, I am encountering errors 1.system cannot find path specified when connecting to FTP server in File to FTP scenario 2.file is not being picked up when the source file is in CSV format in File to File scenario. can any one suggest me something
-
I need to know why I cannot download my purchase movies while working abroad. I work in Iraq and before coming over I purchase the Walking Dead Series, but now when the new episodes comes out I cannon download them. Why is that?
-
Workflow for new starters/leavers
Hello All, I am new to workflow. I have a requirement to send an email to an administrator when a new starter is employed and when an employee leaves. Any ideas on how to do this? Thanks, Nick.
-
I just bought a 1841 router with IOS 12.3 and I succesfully configured Internet access using NAT. Now I want to redirect some ports (25, 100, 3389, etc.) to my internal mail server. I would appreciate some help to do it, using SDM if possible. Thank