How to change the SMTP connection timeout in Thunderbird?

Go to Config Editor
(Tools | Options, select the Advanced panel, select the General tab, and click Config Editor)
and ...
Which parameter need to change?
If I connect to the Internet as:
Computer -> WiFi Router -> 3G Modem -> Internet
then Ping time is big, and OFTEN (but not always) there is an
"Sending of message failed. The message could not be sent because the connection to SMTP server mail.domain TIMED OUT".

Then what other software do you have that fills a security role or what setting on the router or modem need fixing. I use a wifi router and 3G box at work and while the service is not great it does function and ping times are quite reasonable (we are on the out limits of the 3G coverage 1 or 2 bars)

Similar Messages

How to change the smtp. element of the outbound mail server

When adding an existing email account it is not possible to change the 'smtp.' portion of the outbound mail server address.
My smtp server name is 'mailout.easymail.ca'
How can I set this?

It is NOT a prefix. It is a label. It indicates the type of server this particular setting will connect to.
Here are the relevant bits of two of my accounts settings.
account27: 
INCOMING: account27, , (imap) mail.tamba.co.uk:143, plain, passwordCleartext 
OUTGOING: mail.tamba.co.uk:25, plain, passwordCleartext, true 
 
account29: 
INCOMING: account29, , (imap) mail.btinternet.com:993, SSL, passwordCleartext 
OUTGOING: mail.btinternet.com:465, SSL, passwordCleartext, true 
No skulldduggery was required to get those ''mail'' "prefixes" in place. ;-)

How to change the net connection 3g to Wifi

Dear
Please tell me the options for changing the network connection 3g to Wifi in Iphone4
Thanks and Regards
Majeed
0097155-6180290

Hi,
Go to MIRO, enter date,difference amount to be debited to vendor account, replace invoice with subsquent credit. Give PO and it will fetch all related details of materials which were procured using this PO in material tab. In material tab you can charge off the difference by distributing it to materials in the tab. Post the document. It will do the needful for you.
Regards

How to change the default connection

I've to change programmatically the default connection of the report (6i).
I thought to use somenthing like LOGOUT/LOGIN (FORMS6i) in the BeforeReport trigger, but I don't find any valid solution yet.
Thanks in advance,
Raffaele

The reports are developed with Report Builder 6.0.8.8.3.
The server is configurated: Oracle HTTP Server/1.3.22 (Win32)
mod_plsql/9.0.2.0.0 DAV/1.0.2 (OraDAV enabled)
mod_oc4j/3.0 mod_ossl/9.0.2.0.0 mod_fastcgi/2.2.10 mod_perl/1.26
From my application I call iexplore and set the url like:
http://<myserver>/dev60cgi/rwcgi60.exe?MY_REPORT+<jobid>
In cgicmd.dat I defined:
MY_REPORT: report=D:\report_path\theREPORT.rep
userid=def_user/pwd@the_db
server=my_repserver...
In the report, in the BEFORE_REPORT or in BEFORE_PARAMETER_FORM trigger I would like to make a query to a table of def_user with the job_id filter and get the job specific connection info.
Then, I've to re-connect to the new user where the tables of the report's data model a re defined.
Our database is structured with a single user for general data, included the info to address the other schema, and more specific users (~100) for job data.
I've used the tecnique in Forms, but I can't replicate it in Reports.
Thank you for any suggestions.
Raffaele

Where(How to change the SMTP- Server

Hello,
i'm using the OAS 10.1.2.0.2
While installation OAS i entered the name of the actual working SMTP- Server.
Sending mails worked fine until today.
Now the name of the SMTP- Server has changed and i wanted to change it(the name) in the Application Server, but i didn't find one/all place(s) where i had to change the name(s) of the SMTP- Server.
Is there anyone who can help me??
Thanks a lot.
Best regards.
Florian

Refer this:
http://download.oracle.com/docs/cd/B14099_19/core.1012/b13995/reconfig.htm#sthref681
Thanks
Shail

Change the ITS connection to Message Server

Hi Gurus,
Our project is using EP7 to access ECC 6 via ITS web access. EP7 -> ITS -> ECC 6
Currently, we has configured Group access via Message Server on ECC 6. We notice that, the ITS is still connected to Single Application Server on ECC 6. Do anyone know how to change the ITS connection to Message Server instead of Dedicated Application Server?
Please help.
Thanks,
HauChee

Hello,
Let's say your ITS port is 8000
The way to distribute load of integrated ITS requests to the different Dialog instances is to call port 8001 of the message server... That's it...
So basically the rule is:
Always call the message server hostname + defined ITS port number + 1
So in your EP7 system object you define your ITS as:
http://ECCITSMessageServer.domain.com:8001/...
Same rule apply in the WebAS section of that EP system object.
Then, the message server will redirect the request to one of the available dialog instances of integrated ITS on port 8000.
You will be able to see the redirection happenning by using an HTTP sniffer program like HTTPWatch ($$).
Regards,
Marc.

My MacBook Pro persistently will not connect to my wireless router. The message "connection timeout" appears. What is a connection timeout and how can I fix?

My MacBook Pro persistently will not connect to my MiFi Verizon wireless router. The message "connection timeout" appears. What is a connection timeout and how can I fix?

Hi there terri900!
You may want to try configuring your router settings to match the recommended settings for iOS and OS X devices, which can be found here:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
You may also find some helpful information for troubleshooting this issue in this article, which can help you with any manner of issues with Wi-Fi connections:
Wi-Fi Quick Assist
http://support.apple.com/kb/HT1145
Take care, and thanks for visiting the Apple Support Communities.
-Braden

How to change the connection for a recurring report

I have a group of reports running in production on recurring schedules. I need to update the database connection for these as we are changing our server environment.
I open the report in Crystal Reports 11 and changed the database connection saved the report back to the Enterprise Server location (I also have a backup of the original). When I preview the report using the Central Management Console, the report uses the updated database connection info. When I test the recurring report I get a logon failure. When I go to the instance to look at the database logon for the recurring instance it shows the old database connection.
How can this database connection get updated for the current group of instances for these recurring reports?
Thanks
BOBJCMC

Hi Stratos,
I tried to use .NET SDK to update the Logon_Info properties as below. But it does not seem to be working. Is this the correct way to update logon info for recurring instances?
infoObject.ProcessingInfo.Properties["SI_LOGON_INFO"].Properties["SI_LOGON1"].Properties["SI_USER"].Value = <userid>
infoObject.ProcessingInfo.Properties["SI_LOGON_INFO"].Properties["SI_LOGON1"].Properties["SI_PASSWORD"].Value = "pwd"
Thanks
Ajith

How to change the connection to MTP

Please advise how do I change the auto connection to MTP for Iphone 4.

Meaning you have created just the empty data-sources.xml and not configured any Connection Pool and DataSource in JDev?
In Oracle AS 10.1.3 you have two ways to do this:
1. Use JDev and configure the data-sources.xml (Context Menu -> Properties)
2. In Oracle AS: Select application -> Administration -> Services -> JDBC Resources -> Create Pool and Create DataSource
--olaf

How do we change the source connection in OWB?

Hello,
Currently my source connection has read/write privileges. For security reason, i created read only schema in the source database.
Now i want to change my username in the source mapping.
I go to connection Explorer,
click Location
click database
Click oracle
right click on source name(existing one), click open editor.
When i click open editor, I see all the user info are grayed out. I could not change anything.
How do i change the current source connection username?
Any help is appreciated..

Hello, I have trouble changing the source connection.
My source connection name is same as before. Only DB name, schema name is changing now for source connection. Here are the steps i have done.
1. Went to control center manager and unregister the source mapping.
2. Went to Connection explorer and right click on source connection and click the open editor. change the username, password, ip address, DB name.
3. went to control center manager and re-deploy the mapping. It is not working... It says, table or view does not exists.
Is ther any other place i need to change... Somewhere i am missing..
Any help is highly appreciated..
Edited by: Shrinika on Oct 21, 2010 9:52 AM

How to make a socket connection timeout infinity in Servlet doPost method.

I want to redirect my System.out to a file on a remote server (running Apache Web Server and Apache Tomcat). For which I have created a file upload servlet.
The connection is established only once with the servlet and the System.out is redirected to it. Everything goes fine if i keep sending data every 10 second.
But it is required that the data can be sent to the servlet even after 1 or 2 days. The connection should remain open. I am getting java.net.SocketTimeoutException: Read timed out Exception as the socket timeout occurs.
Can anyone guide me how to change the default timeout of the socket connection in my servlet class.
Following is the coding to establish a connection with the Servlet.
URL servletURL = new URL(mURL.getProtocol(), mURL.getHost(), port, getFileUploadServletName() );
URLConnection mCon = servletURL.openConnection();
mCon.setDoInput(true);
mCon.setDoOutput(true);
mCon.setUseCaches(false);
mCon.setRequestProperty("Content-Type", "multipart/form-data");
In the Servlet Code I am just trying to read the input from the in that is the input stream.
public void doPost(HttpServletRequest req, HttpServletResponse res)
throws ServletException, IOException
BufferedInputStream in = new BufferedInputStream(req.getInputStream());
byte [] content = new byte[1024];
do
read = in.read(content, 0, content.length);
if (read > 0)
out.write(content, 0, read);
I have redirected the System.out to the required position.
System.setOut(........);
Can anyone guide me how to change the default timeout of the socket connection in my servlet class.

I am aware of the setKeepAlive() method, but this can only used with the sockets. Here i am inside a servlet, have access to HTTPServletRequest and HTTPServletResponse and I don't know how to get access to the underlying sockets as the socket handling will be handled by the tomcat itself. If I am right there will be method in the apache tomcat 6.0.x to set this property. But till now I am not getting it.

How to change the default time?

when you finish the action of dialing ,the CCM system recognize your finish after 10s .How to change the default time in Service Parameters ,which is the detail Parameters ?

Please see the following link for information on configuring the interdigit timeout.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00800dab26.shtml
Hope this helps. If so, please rate the post.
Brandon

How to change the 'Default operating mode' of a mapping on the repository and not from the client

Hi everybody,
I am using OWB 11.2.0.3 and under the mapping's configuration property, I have the necessity to change the Run time parameter "Default operating mode" to SET_BASED in almost all my mappings.
Because I have 745 mappings in which the Default operating mode is different from SET_BASED, instead to open 745 times the 'Configure' and update manually the value, is there a way to update safely these values (with an oracle predefined script) directly on the repository ?
I know that exists a view called CMPSTRINGPROPERTYVALUE_V based on a table called CMPSCOPrpClasses, but changing this table it's very complicated for me because contains only keys and then I don't know in which way is connected with all the other structures....
If somebody knows a method more efficient to do these updates on the repository and not from OWB client I will appreciated it!
Thanks in advance
Alessandro

Urgent... help!!! Thanks
in short, my server log says transaction access mode is "read only", so my calling home.create() always triggers a transaction rollback. How to change the access mode to "read write"?
Is possible to work out through one of the descriptor files? Or ini settings of the underlying pointbase database? Or any other way around?

How to change the storage location in Lightroom 3.6.?

How to change the storage location in Lightroom 3.6.?
I use my internal hard drive NTFS of my MacBook Pro as my storage location of Lightroom 3.6. being installed in Snow Leopard now but the data of my photos get too big now. I have two fast and big external hard drives eSATA now which I want to use for my data/photos. I know how to copy the data from one hard drive to another but I don't know how to change the settings in connection with Lightroom easily. I still want to watch all fotos on my MacBook Pro but don't want to save any fotos on my internal harddrive any more. Isn't it possible to have the programm Lightroom on my internal harddrive but the data on two times on two different extermal hard drives? If I look at Lightroom - settings of catalogue - I see that the internal harddrive location is my storage location now but I my two external harddrives don't appear as folders. Why? How to change that so that the external hard drives appear in Lightroom and I can watch all my fotos immediately (sometimes using external hard drive 1 and sometimes using external hard drive 2)?
My external hard drives are in HFS+ but I use the software of Paragon so that there shouldn't be any problem to read and write the data (I use also Final Cut Express so my external hard drives are HFS+ and not NTFS).
I want to impert many data from CDs - should I copy the fotos first to my external hard drive and then import it into Lightroom or is it easier to import the data directly from the CD in Lightroom so that I don't have to name the folders two times?
I see that I have to sort the fotos from the CDs in new different folders and an used to do that in Finder of my MacBookPro. In Lightroom I don't want have to click each of hundreds of fotos to be able to put it into the right folders ... But how to import only a part of a CDs quickly into the right (newly created) folders?
Kind regards, Karin

Would you really leave the names of photos like DSC05271.ARW and DSC05271.jpeg etc.?
What if I name them f.i. like ...
2013-09-11_Austria_1_mountain.jpeg
2013-09-11_Austria_2_mountain.jpeg
2013-09-11_Austria_3_valley.jpeg
I would NOT do this. I would not change the file name.
I would add keywords and other metadata to the photos to identify the content of the photos, and from that point on, I would use keywords and other metdata to search for these photos.
However, let's look at the big picture. I think there are three different methods of organizing
Organize via keywords and other metadata, and not via operating system constructs such as file name and folder name
Organize via operating system constructs such as file name and folder name, and not via keywords and other metadata
Some combination of 1 and 2
You can choose any one of the three methods above, the choice is yours. I am a very strong believer that for most people (and it sounds like you are one of those people), method 1 is the best method. However, not everyone agrees.
There are drawbacks to using file names to identify your photos. One big drawback is that you must type the information into each photo's name, and this is more tedious than if you wanted to assign the keyword "mountain" to the photos, you can assign the keyword to multiple photos at once. Also, if you mis-spell the information in the file name on any photo, you have just made the photo much harder to find; whereas in Lightroom, the keyword can be assigned via a mouse click (so you can't mis-spell it), or by typing the first few letters and Lightroom (auto-fill) will find the correct keyword name. So using keywords is a much simpler way to go.
.. is this much too complicated to do that in Lightroom or even dangerous to got lost of photos?
It is very simple to add keywords, as I explained for this case. Create keywords "Austria", "Mountain", "Valley"; then select the desired photos, and then click on the check box next to the keyword name. It is much more complicated in my opinion to rename the photos in this manner.
There is less danger in doing this via keywords than the danger doing this via file names, because of potential mis-spellings.
If I spend a lot of time in editing photos (in Lightroom or Photoshop) I don't want that I loose those photos f.i. later if Lightroom won't be the software I use regarding the photos (in 10, 20 years?!)
Lightroom will OPTIONALLY write your keywords and other metadata to the files (or sidecar files in the case of RAW). Every photographic application I know of (and I'm sure those in the future) can read the keywords and other metadata. So if you ever want to switch to some other software, your keywords and other metadata are available. you can turn this option on via Edit->Catalog Settings->Metadata, check Automatically Write Changes to XMP.
So I have to create two folders - one with the originals and one with the edited exported photos?
No, you do not have to create two folders. You don't have to export everything, but if you do, you can put the exports wherever you want, including putting them in the same folder as the originals, with different name.
Why not edit them in Photoshop and save them in the second folder which I import later in Lightroom? Because it takes longer?
Wow, you really need to think about: Why are you using Lightroom?
Could you explain this to me? Why are you using Lightroom?
If your goal is to edit the photos in Photoshop, and then put them in folders with whatever custom name you want to give them, then what is the benefit of using Lightroom? You can do all of this WITHOUT Lightroom. You keep explaining that your intended goal is to use Photoshop and folders/file names, and this is a goal which AVOIDs all benefits of Lightroom. I can't understand what you think the benefits of using Lightroom are for you.
It is starting to sound to me like Lightroom is not the right software for you.
Some people want to see a movie on their TV and are able to watch a DVD (not all!). Flickr seems to be a solution for movies in a big size (many GBs) to share them with friends (?)
You haven't mentioned this before, and you should check the rules on Flickr regarding how long a video you can upload.

How to change the Timestamp In a program

Hi,
We faced a problem today, Some of the critical jobs from a source system are going to short Dump. Unfortunately we couldn't find any lockwaits, deadlocks and any delay in SM37. After analyzing, we came to know that, SAP trace indicates failure occured during program /GLB/RGTCSR_RC_INV execution :
B *** ERROR => DISTRIBUTED_TA_FAILED:
The timestamp for the execution of the program has been set as "20.070.801.000.000", that does mean it will try to retrieve all values after the date 01.08.2007 and the time 00:00:00. Now checking on the code we can see there is a logic written which retrieves the values from the table /GLB/RGTT_CS_RC, checking on the Goods Movement status (wbsta) , timestamp and document number (VBELN_SO) if any. For this case VBELN_SO is blank and vbsta is equal to space (Not Relevant). This retrieval helped to logic to retrieve 706706 document and items from the table. This amount of data is huge and we would like to request BW team to run the program with a smaller timestamp to avoid any inconsistencies and also to avoid the dumps which can occur when we try to play with this huge entries.
Checking on the code, two similar selects have been written on the same table /GLB/RGTT_CS_RC, firstly to select all the document numbers relevant to the timestamp and wbsta value and secondly to check "Get records that may have already been used", depending on the document number and item numbers. But as we are doing a select * it will automatically select VBELN_SO as well as POSNR_SO. Hence, the second select from the same table is irrelevant and it will only effect the performance of the system, in the worst case it will terminate the program with this huge amount of entries. Hence, this logic has to be combined to one single select for which the first select statement is enough. Playing with a huge amount of data 706706, and retrieving from the same table twice can surely result in a short dump. Also there are couple of loops has been done on the same table which reduces the performance too.
Possible solution looks like we need to reduce the time stamp and run it,
can some one tell me how to change the time stamp in a program???

First check the connection with the source system. If its ok then replicate the datasource and activate. Then try with running job.
Time stamp error usually happens when source system in BI and r/3 side differs.

How to change the SMTP connection timeout in Thunderbird?

Similar Messages

Maybe you are looking for