How to change the wireless driver?

Well, firstly, hello all.
I've been looking around for some time alredy, about the correct driver for my wireless card (Belkin F5D7000 PCI). I found that the most compatible one is b43. I followed all the steps on the wiki, but still when I look on the info of NetworkManager, it says I use the rtl8180 driver. How could I change this?

The output.
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b2)
00:03.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.2 SMBus: nVidia Corporation MCP79 SMBus (rev b1)
00:03.3 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.4 RAM memory: nVidia Corporation Device 0a98 (rev b1)
00:03.5 Co-processor: nVidia Corporation MCP79 Co-processor (rev b1)
00:04.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1 Controller (rev b1)
00:04.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0 Controller (rev b1)
00:06.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1 Controller (rev b1)
00:06.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0 Controller (rev b1)
00:08.0 Audio device: nVidia Corporation MCP79 High Definition Audio (rev b1)
00:09.0 PCI bridge: nVidia Corporation MCP79 PCI Bridge (rev b1)
00:0a.0 Ethernet controller: nVidia Corporation MCP79 Ethernet (rev b1)
00:0b.0 RAID bus controller: nVidia Corporation MCP79 RAID Controller (rev b1)
00:0c.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:15.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:16.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:17.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:18.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
01:07.0 Ethernet controller: Belkin Device 700f (rev 20)
02:00.0 VGA compatible controller: nVidia Corporation Device 0644 (rev a1)
05:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. IEEE 1394 Host Controller

Similar Messages

Satellite M30 Pro: how to change the optical drive?

Hi there,
could anybody please give me a hand on changing/replacing the optical drive on my Satellite Pro M30?
Alas, my drive is a DVD-ROM/CD-RW. I have another one with the capability of burning DVD's (Super-Multi drive from Matsu****a). I just wonder how I could replace them, since it os not possible to easily slide them out?
Thank you.
Jan

Hi
To remove the optical drive you need only to remove 2 screws which are placed at the bottom of the unit on the drive side. Then you can simply slide outward the drive to disconnect it from the connector on the system board.
The drive is placed in the plastic frame. So you need also this frame for a new drive.
To remove the plastic frame from the device you have to remove 4 screws.
Bye

How to change the midp version in ktoolbar of wireless toolkit 2.1

Hi
How to change the version of midp in ktoolbar of wireless tool kit 2.1
though i tried to change the platform by selecting midp1.0 from settings
dialog box iam geeting alert:BadVersion Error
and the application is terminated abruptly
do i need to change any configuration files
please suggest me
as it is very urgent

The version of Java inside the database? If so - Not recommended at all ... the environment is NOT the same as your grandfathers JRE and there are a few noteworthy conditions.
How much of the Oracle Java Developer's Guide have you reviewed? http://www.oracle.com/pls/db102/to_toc?pathname=java.102%2Fb14187%2Ftoc.htm&remark=portal+%28Books%29

Is it possible to change the hard drive in a macbook pro, if so where from? and how?

is it possible to change the hard drive in a macbook pro, if so where from? and how?

secondrow wrote:
whats a green drive? thnks
Green is a marketing term for a drive designed for lower power use, lower noise, and lower heat. The side effect is that it's not as fast. Black drives are designed for highest performance, so they might use more power and run hotter and noisier. I upgraded my Apple Time Capsule with a green drive, but I put a black drive in my Mac Pro.
Kappy wrote:
7200 RPM drives are faster than 5400 RPM drives.
As in cars, RPM is not the sole determinant of performance. In some cases, a newer drive at a lower RPM is faster than an older drive at a higher RPM, when the newer drive uses better technology. I have heard that some of today's high-capacity 5400RPM drives are faster than 7200RPM drives of lower capacity simply because the very high density of a 1TB drive means more data passes under the head even at a lower RPM. Certainly there have been times in Apple's past when new lower RPM drives were faster than higher RPM drives of the previous generation, a notable example being when 4200RPM perpendicular recording drives were introduced and beat 5400RPM drives.
Yes, generally RPM can be used to compare, but it is important to realize it isn't always true.

I have recently had my hard drive replaced due to a fault whilst in Germany working. Happy with the replacement, however when i go to log on as a user that screen is in German? Any idea how to change the language?

i have recently had my hard drive replaced due to a fault whilst in Germany working. Happy with the replacement, however when i go to log on as a user that screen is in German? Any idea how to change the language?

Greetings Lex,
Kind of you to comment ... but you are also adding years to my signature! I know I'm 76 but I don't want to think about it.
Regards 71.

How to change the country code for Wireless channel usage

My MacBook country code is set by Japan.
In this case, I can use only 5.15~5.25 channels from ch#36 to ch48 at 5GHz Band.
I'd like use the other channels..by other country code.
How can I change the Wireless card country code?

The country code is automatically detected and set by your router. Wireless routers use the frequencies specified by the regulatory agencies in the countries in which they are sold.
There is nothing to change in your MacBook.

How to change the battery in the imac wireless keyboard

how to change the battery in the imac wireless keyboard?

FYI, there is no "iMac" wireless keyboard.
If you have an Apple Bluetooth KB, simply remove the plug (screws out) on the left top side of the KB.
Barry

HT3986 Using Boot Camp 4 and Windows 7. Try to change name of the C: drive and get the dialog "You will need to provide administrative permission to change the name". How do I change the C: drive name?

I tried to change name of the C: drive and get the dialog "You will need to provide administrative permission to change the name". How do I change the C: drive name?

Forgot to specify:
Im using an older Unibody Macbook (back when they were not all macbook pro's) 2008ish with Snow leopard 1.6.8
The thread you linked me to, Eric, shows the guy 'Niganit' with the eXACT SAME PROBLEM as me! He seems to have found out the problem but I dont see his resolve.
I just dont have the option to install windows 7 in any other form that a cd
a picture;

How do I change the install drive default for Creative Cloud Suite? I have a 64 gb SSD drive as dri

I bought another 128 GB SSD drive just for the Adobe applications. I can't figure how to change the download destination as it download or before it installs. What am I missing here?

I am sorry Scottcommercialrealtor I missed the fact you were installing Creative Cloud, we have had a lot of traffic with the release of CS6 and Creative Cloud, you can only customize the install location for Creative Cloud. You can do so by clicking on your name in the Adobe Application Manager and selecting preferences. The install files will have to be downloaded to your OS volume but you can choose to install many of the components of the applications on a separate drive. The shared components though will also need to be installed on your OS volume.
SSD solutions I would honestly recommend having your OS and Apps installed on the same drive so you can maximize your performance. You can then use a standard hard drive for your documents, videos, and images. You mentioned that you purchased a 128 gig SSD. You might consider cloning the 64 gig drive over to the 128 and then having your OS and Apps installed on the same drive.

HT4946 how to change the back up location on windows 7,c drive is almost full

how to change the back up location on windows 7,c drive is almost full

This is not a feature of iTunes.
See this thread for way to "trick" iTunes into backing up to a different location:
https://discussions.apple.com/message/20590667#20590667

How to change the letter on external HDD

My external hard drive was originally on the F drive and with this I had all my iTunes music too. However, for some reason, my computer has stopped recognizing the F drive; the following message is displayed when trying to open this drive:
"The drive or the network connection that the shortcut 'F Drive.ink' refers to is unavailable. Make sure that the disk is properly inserted or the network resource is available, and then try again."
The problem I now have is that the external hard drive is now the G drive and iTunes doesn't seem to recognize the path (G:\iTunes) I have told it to use, i.e., my music is not loading properly and only a small fraction is playable.
Can anyone help me on this matter?

Hi
I would recommend changing the external drive letter (G:) back to F.
Do you know how to do this?
After the external HDD was connected you should access the disk management and there you will see the HDD (single partitions) and the other drives.
Then you should mark the external HDD and should change the letter to F.
Possibly the F letter was reserved for another drive.
In such case you have to unlock the F letter by assigning another letter to the drive which uses the F letter.
For details please check the Microsoft knowledge document;
[How to change drive letter assignments in Windows XP|http://support.microsoft.com/kb/307844]

How to change the frequency of pulse train on the fly using an array of values?

Hi all!
First I want to thank U for the great job you are doing for this forum.
Iam still busy trying to control a stepper motor, by sending pulses from my E-series 6024 to a compumotor s6- stepper Driver. I've managed to get it working. I desperately need to control the motor using the values from an array. I believe we can use two approaches for that:
1st - I can get an array of the "numbers of pulses". Each element must run for 10 milliseconds. Using that we can calculate the array of frequencies to send the number of pulses within 10 milliseconds for each specific element. Could we use the arrays of "number of pulses" and frequencies in a "finite pulse train " and up
date with each element every 10 millisecond?
2nd - Or Could we use of the frequency array in a "continuous pulse train vi" and update it every 10 milliseconds?
Please note that I must use the values as they are.
Can someone please built a good example for me? Your help will be appreciated.
Regards
Chris
Attachments:
number_of_steps.txt ‏17 KB
frequency.txt ‏15 KB

Tiano,
I will try to better explain the paragraph on LabVIEW. The original paragraph reads ...
"While in a loop for continuous pulse train generation, make two calls to Counter Set Attribute.vi to set the values for "pulse spec 1" (constant 14) and "pulse spec 2" (constant 15). Following these calls you would make a call to Counter Control.vi with the control code set to "switch cycle" (constant 7). The attached LabVIEW programs demonstrate this flow."
You can make two calls to Counter Set Attribute or you can make a call to Set Pulse Specs which, if you open this VI, you will see that it is just making two calls to Counter Set Attribute. What you are doing with the Counter Set Attribute VIs is setting two registers called "pulse s
pec 1" and "pulse spec 2". These two registers are used to configure the frequency and duty cycle of your output frequency.
The example program which is attached to this Knowledge Base demonstrates how to change the frequency of a continuous generation on the fly. Why continuous? Because changing the frequency of a finite train would be easy. When the train completes it's finite generation you would just change the frequency and run a finite train again. You would not care about the time delay due to reconfiguration of the counter.
If you would like to change the frequency of the pulse train using a knob, this functionality will have to be added in the while loop. The while loop will be continuously checking for the new value of the knob and using the knob value to set the pulse specs.
LabVIEW is a language, and as with learning all new languages (spoken or programatic) there is a lot of learning to be accomplished. The great thing is that LabVIEW is much easier than mo
st languages and the learning curve should be much smaller. Don't fret, you'll be an expert before you know it. Especially since you're tackling a challenging first project.
Regards,
Justin Britten

How to change the storage location in Lightroom 3.6.?

How to change the storage location in Lightroom 3.6.?
I use my internal hard drive NTFS of my MacBook Pro as my storage location of Lightroom 3.6. being installed in Snow Leopard now but the data of my photos get too big now. I have two fast and big external hard drives eSATA now which I want to use for my data/photos. I know how to copy the data from one hard drive to another but I don't know how to change the settings in connection with Lightroom easily. I still want to watch all fotos on my MacBook Pro but don't want to save any fotos on my internal harddrive any more. Isn't it possible to have the programm Lightroom on my internal harddrive but the data on two times on two different extermal hard drives? If I look at Lightroom - settings of catalogue - I see that the internal harddrive location is my storage location now but I my two external harddrives don't appear as folders. Why? How to change that so that the external hard drives appear in Lightroom and I can watch all my fotos immediately (sometimes using external hard drive 1 and sometimes using external hard drive 2)?
My external hard drives are in HFS+ but I use the software of Paragon so that there shouldn't be any problem to read and write the data (I use also Final Cut Express so my external hard drives are HFS+ and not NTFS).
I want to impert many data from CDs - should I copy the fotos first to my external hard drive and then import it into Lightroom or is it easier to import the data directly from the CD in Lightroom so that I don't have to name the folders two times?
I see that I have to sort the fotos from the CDs in new different folders and an used to do that in Finder of my MacBookPro. In Lightroom I don't want have to click each of hundreds of fotos to be able to put it into the right folders ... But how to import only a part of a CDs quickly into the right (newly created) folders?
Kind regards, Karin

Would you really leave the names of photos like DSC05271.ARW and DSC05271.jpeg etc.?
What if I name them f.i. like ...
2013-09-11_Austria_1_mountain.jpeg
2013-09-11_Austria_2_mountain.jpeg
2013-09-11_Austria_3_valley.jpeg
I would NOT do this. I would not change the file name.
I would add keywords and other metadata to the photos to identify the content of the photos, and from that point on, I would use keywords and other metdata to search for these photos.
However, let's look at the big picture. I think there are three different methods of organizing
Organize via keywords and other metadata, and not via operating system constructs such as file name and folder name
Organize via operating system constructs such as file name and folder name, and not via keywords and other metadata
Some combination of 1 and 2
You can choose any one of the three methods above, the choice is yours. I am a very strong believer that for most people (and it sounds like you are one of those people), method 1 is the best method. However, not everyone agrees.
There are drawbacks to using file names to identify your photos. One big drawback is that you must type the information into each photo's name, and this is more tedious than if you wanted to assign the keyword "mountain" to the photos, you can assign the keyword to multiple photos at once. Also, if you mis-spell the information in the file name on any photo, you have just made the photo much harder to find; whereas in Lightroom, the keyword can be assigned via a mouse click (so you can't mis-spell it), or by typing the first few letters and Lightroom (auto-fill) will find the correct keyword name. So using keywords is a much simpler way to go.
.. is this much too complicated to do that in Lightroom or even dangerous to got lost of photos?
It is very simple to add keywords, as I explained for this case. Create keywords "Austria", "Mountain", "Valley"; then select the desired photos, and then click on the check box next to the keyword name. It is much more complicated in my opinion to rename the photos in this manner.
There is less danger in doing this via keywords than the danger doing this via file names, because of potential mis-spellings.
If I spend a lot of time in editing photos (in Lightroom or Photoshop) I don't want that I loose those photos f.i. later if Lightroom won't be the software I use regarding the photos (in 10, 20 years?!)
Lightroom will OPTIONALLY write your keywords and other metadata to the files (or sidecar files in the case of RAW). Every photographic application I know of (and I'm sure those in the future) can read the keywords and other metadata. So if you ever want to switch to some other software, your keywords and other metadata are available. you can turn this option on via Edit->Catalog Settings->Metadata, check Automatically Write Changes to XMP.
So I have to create two folders - one with the originals and one with the edited exported photos?
No, you do not have to create two folders. You don't have to export everything, but if you do, you can put the exports wherever you want, including putting them in the same folder as the originals, with different name.
Why not edit them in Photoshop and save them in the second folder which I import later in Lightroom? Because it takes longer?
Wow, you really need to think about: Why are you using Lightroom?
Could you explain this to me? Why are you using Lightroom?
If your goal is to edit the photos in Photoshop, and then put them in folders with whatever custom name you want to give them, then what is the benefit of using Lightroom? You can do all of this WITHOUT Lightroom. You keep explaining that your intended goal is to use Photoshop and folders/file names, and this is a goal which AVOIDs all benefits of Lightroom. I can't understand what you think the benefits of using Lightroom are for you.
It is starting to sound to me like Lightroom is not the right software for you.
Some people want to see a movie on their TV and are able to watch a DVD (not all!). Flickr seems to be a solution for movies in a big size (many GBs) to share them with friends (?)
You haven't mentioned this before, and you should check the rules on Flickr regarding how long a video you can upload.

How to change a hard drive in a first generation intel Imac?

My hardrive cratered today on my first gen intel. where can I find the info for How to change a hard drive in a first generation intel Imac?

Go to http://www.ifixit.com/Browse/iMac_Intel , choose your system, and choose hard drive replacement to see how to do that.

I just fix my macbook air because it was kernel panic. They changed the hard drive. I could not back up with Time Machine, because it did not work and I had over Adobe creative suite 5 design premium student. But I finished my studies last year and I'd li

I just fix my macbook air because it was kernel panic. They changed the hard drive. I could not back up with Time Machine, because it did not work and I had over Adobe creative suite 5 design premium student. But I finished my studies last year and I'd like to know how to get the serial number for me to reinstall Adobe creative suite 5 design premium when I am no longer study because I would still like the used? It is not fair if I do anymore because I really need.

You can download Creative Suite 5 here:
Other downloads
To deal with the issue of the serial number and using it again, you'll have to use Web Chat. Here's a link:
Adobe ID, sign in, and account help
See the bottom of the page for a link

How to change the wireless driver?

Similar Messages

Maybe you are looking for