How to check UC560 FXO Port Not Problem Question
Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your Attention
Hi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad.
Similar Messages
-
Uc560 fxo port not answering incoming calls
Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj -
How to check if there is any problem in the interaction center inbox
hi,
how to check if there is any problem in the interaction inbox for recieving the attachments/cic0
some users who are sending withattachments is not able to reach the sap indox./
but without the attachments the mails are coming
I want to know how we can able to find out were is the problem.
thanks in advance
Prajith Phi,
Any update for the above query.
Thanks & Regards
Prajth P -
FXO port not going back onhook when call goes to CUC Voice mail.
HI All,
Quiet new to the voice world and have just set up a home lab and have run into the following problem.
When a call comes in from the PSTN and gets transferred to voicemail CUC, when the caller has left the message and hung up the FXO port on my Cisco 3825 does not go back on hook
If a call comes in from the PSTN and is answered on a phone registered to the CUCM and the internal user hangs up the FXO port goes back on hook but if the caller hangs up the FXO port does not go back on hook.
I am using H.323 between the 3825 & CUCM
PSTN ------->Voice Gateway 3825-------->CUCM-------->CUC
Anyone got any ideas as to why this is happening?
ThanksHi Shaun,
The router DSP port is not able to detect the disconnect tone sent by provider that is why FXO port is remaining off hook. When call is answered by IP phone then IP phone user can listen the disconnect tone when PSTN caller disconnectes the call and they will hang up the call so gateway is aware that call is disconnected and moves the port to ON hook state but CUE cannot understand the tone so it keeps the call active. To resolve the issue we ave to configure custom CPTONE. Kindly collect PCM capture for a test call. Disable capture after call is disconnected by PSTN caller. i have attached the document. Use the method according to your IOS version.
Using PCM capture we can findout the exact frequency and cadence of the disconnect tone sent by provider. -
How to check all items are not null in CAML Query?
HI All,
In a CAML Query, i got three items. In all three items, a particular column(Closure Date) should not be null. How to check in all three items, where 'Closure date' is not null?
Thanks in advance!Hi,
Try this:
"<Where><IsNull><FieldRef Name='Closure Date' /></IsNull></Where>"
Hope it hepls!
Thanks,
Avni Bhatt
If this helped you resolve your issue, please mark it Answered -
Photosmart printer D110A CN732A How do I solve a port match problem?
operating system: windows 7
Error message: port match
Any changes made to your system before the issue: No
When I go to print something It tells me it's printing, but then never does. The explanation is always just the simple "error". I've used troubleshoot, re-started everything and ran the diagnostic test which told me it was a port match problem. My printer will still copy.Hi there,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too. -
How to check that Delta is not captured?
Dear Experts,
I am using 2LIS_02_ITM datasource.
PO is created using a program.
The next step in the program, it can change a field in the PO depending on logic, using a abap command 'update'.
Sometimes, this change is not captured in the delta queue, it seems.
why i say this is the PO shows the field value but BI delta load does not.
It is using Queued Delta now.
Initially, the program uses a command 'update' to update the field in PO.
Now, we decided to use ME22N program to ensure delta will be created.
The problem is happening to some records and not all delta records.
Its very difficult to tell what is the cause.
What is the standard method to check that Application table data is not captured in Delta Queue by the extractor?
Or
If PO can show the field value, is there a possibility that Delta may not capture this field change?
regards
PascalWell just throwing few possibilities:
1 - Basically PO creation, change in values/quantities etc are Business transactions and they generate evens known as BTEs.
Now we have to explicitly inform SAP ECC that which applications can use BTEs and we do this by tcode BF11.
Check if the software component creating and changing POs is properly linked to BTEs and if BW is set as active in BF11 tcode.
2 - If point 1 is checked and nothing is found to be incorrect, please check if Industry sector is correctly chosen (SBIW). Industry sector generates a set of Transaction keys (BWVORG) without which the values are not updated in BW.
Also rightly pointed by Tbollo, you need to ensure that there's a pattern in the missing docs to identify the rootcause.
Debanshu -
How to check the VXML Port utilisation in CVP
Hi,
Currently we are using 300 VXML Ports but while monitoring the Active Call in Operational Console
it is showing 300 + Active calls in the VXML Server.
Please kindly help me to findout why Active calls status is showing mor than 300 +.
Regards,
A.Pravin RajYou can check VXML port Utilization by running status.bat file , it will show you the exact ports usage & it will also displays on which application how many callers are.
c:/Cisco/CVP/VXMLServer/admin -
How to check a downloaded OSS Note?
Hi all,
I asked to ABAP team to download one OSS Note.
OK, the Oss Note has been already downloaded.
Now, how can I check, in the system, this downloaded OSS notes?
Thanks all and rgds,
BarbaraHi,
Go to SNOTE transaction.
In that download ur SAP note.
And GOTO SAP NOTE---> IMplement.
It will give info if it is already implemented.
Else u can implement it..
Cheers,
Simha,. -
How to check customer reference no. not being use more than once
I have the following situation and appreciate if some one could show me a simple solution.
On the Sales order window, when user enter a value for Customer Ref. No, check if the entered value has already been used on any existing Sales Order, and give message eg. this Ref. No already been used in SO. 257
What is the easiest way of implementing the validation?
Using Formatted Search?
Triggers or Stored Procedure?
Or one must go about doing this simple task using SDK, DIAPI?
sample code illustrating solution would be much appreciated.
I tried to create a query and used it with Formatted search on the Field, but failed on an error.
the code using temporary hard coded value instead of $[$x.0.0] looks like this
if (SELECT COUNT(*)
FROM dbo.ORDR
WHERE (NumAtCard = 'AAA' and CardCode ='1234')
) =0
Begin
select 'AAA' --redisplay value
end
else
begin
SELECT TOP 1 'already used in SO '+ Convert(Char(3),DocEntry)
FROM dbo.ORDR
WHERE (NumAtCard = 'AAA')
end
where 'AAA' is the reference no. to check for customer '1234', this code works when I run it in SQL query analyser, but failed when I run it as query in Business one. the idea was to redisplay the entered No. 'AAA' if it is not found in any existing SO for cust ='1234'
can anyone point out what the error is or show alternative code for the query.
thanksHi Andy,
I believe the best way to do this is probably to use the SDK as (to my knowledge) this is the only way you can get a message to be displayed and to stop the actual processing of the document.
If you want to go the formatted search route I would suggest you change your query a bit. I have played with your query and the following is an example as I got it working in SBO. I think SBO gets confused if there is more than one select statement that returns a result and I have started using variables to save the results of the select statements in.
[code]Declare @Val varchar(100)
declare @Count integer
set @Val = $[$14.0.0]
if (SELECT COUNT(*) FROM dbo.ORDR WHERE (NumAtCard = @Val and CardCode = $[$4.0.0])) > 0
begin
SELECT TOP 1 @Val = 'already used in SO '+ Convert(Char(3),DocEntry) FROM dbo.ORDR WHERE (NumAtCard = @Val)
end
select @Val[/code]
I hope it helps a bit,
Adele -
How to check mails send or not
Dear All,
I am Using Java Mail API to send mail even if there are some invalid mailids in the cc list, But some time mail are not sending because of some mail server issues(eg insuffcent storage), Is there any fuction to handle this issues,Please advice me how to identify.
Is there any other way apart from catching the "SMTPSendingFailedException"
with Regards,
Prakash Shanmugamksp wrote:
Now I have 2 more questions now
1) When we use attach option in java mail API, the junck are displayed in our java server console, how to block this unwanted junck characters.What junk characters? Maybe you need to disable debugging or not log to the console, but to file or something.
2) Is there any function to store the mail contant and send it automatically to the mail server, when the mail server gets ready.No, you will need to write that yourself. -
How to check that exception is not thrown for particular exception alone
Hi,
I want to check for Exception but I don't want it to throw exception when it is
java.net.SocketException.
I want to throw message for all other exception.
Please let me know how to implement it.
Thanks & Regards,
Nasrin.Ntry {
//some exception throwning code
} catch (SocketException e) {
//handle the exception
} catch (Exception e) {
//all other exceptions are handled here
} -
How to check iPhone 5S is not refurbished
Hi there.
I have a ques ...
I wanna buy an iPhone 5S but quite concern about the device quality (original and not refurbished).
Actually I am not able to but the iPhone from Apple directly as at my Country no Apple store available yet unfortunately. So I need to buy from a local smartphone store at my Country.
Can anyone please advise me ... the best way to check iPhone 5S is original and not refurbished?
Thanks in advance.
Regards.Hi Ralph.
Few more ques please.
- From the serail check result of selfsolve.apple.com, by which parameter I can undersatnd its not refurbished?
- Is there any other way to get Serial number rather than Settings > General > About?
Sorry to ask silly ques ... I dont have any iPhone nearby right now to check.
Thanks.
Regards. -
Call into an MGCP controlled FXO port not connecting
my setup is
PSTN --- GW --- CUCM --- 6921 phone
when we call from the PSTN then call rings and shows connected on the PSTN phone after about 10 sec the call disconnects with fast busy but the 4 digit plar does not ring at all, outgoing calls are working fine. Need help in resolving this issue
ShabbarFXO is configured as loop start as below, cannot run the debug isdn
R_SCI_KQ#debug isdn q931
^
% Invalid input detected at '^' marker.
Registration
Registered with Cisco Unified Communications Manager 192.168.0.26
IP Address
192.168.100.6
End-Point Name
AALN/S0/SU0/0@R_SCI_KQ.sciafrica.net
Description
Device Pool
DP_KQ -- Not Selected -- Cisco Unity voice Mail Ports DP_DAR DP_DRC DP_MOZ DP_ZAM UCCX
Common Device Configuration
< None >
Media Resource Group List
MRGL < None >
Packet Capture Mode
None Batch Processing Mode
Packet Capture Duration
Calling Search Space
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
AAR Calling Search Space
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Location
Hub_None Kenya Mozambique Phantom Shadow Zambia
AAR Group
< None > AAR_GRoup
Network Locale
< None > Argentina Australia Austria Belgium Brazil Canada China Colombia Cyprus Czech Republic Denmark Egypt Finland France Germany Ghana Greece Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Japan Jordan Kenya Korea Republic Lebanon Luxembourg Malaysia Mexico Nepal Netherlands New Zealand Nigeria Norway Pakistan Panama Peru Philippines Poland Portugal Russian Federation Saudi Arabia Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey United Kingdom United States Venezuela Zimbabwe Itu Chile Bulgaria Croatia Romania Serbia and Montenegro United Arab Emirates Oman Kuwait Algeria Bahrain Iraq Mauritania Republic of Montenegro Morocco Qatar Republic of Serbia Sudan Tunisia Vietnam Yemen Lithuania Latvia Estonia
Use Trusted Relay Point
Off On Default
Transmit UTF-8 for Calling Party Name
Called Party Transformation CSS
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Use Device Pool Called Party Transformation CSS
Enable Caller ID -
How to check if Delta is having problem in R/3?
Hi Experts,
In LBWE, is there anything to check regarding delta setting for standard Extractor in R/3 ? What settings affect Delta? Do customizing settings in LBWE affect?
Would really like to get some help here.
regards
PascalHi,
Please examine note 505700. It gives information about lbwe.
Regards.
Maybe you are looking for
-
I am repeatedly having to reset my homepages in the Tools and Options toolbar. Why are my homepages being replaced without my permission?
-
GRC 5.3 CUP SP16 - User info not loading from LDAP into CUP
Hello, We have multiple LDAPS that we needed to connect to our CUP system to authenticate the userids before a request can be created for them. And also to bring in Manager ID and manager email from LDAP as the first level approver for requests. My c
-
SAP screen is displayed in ITS mobile
Hi friends, I am new to ITS mobile. I am getting 2 errors The error is given below. 1. ITS mobile displays SAP screen. 2. ITS_REFERENCE_NULL: Template "itsmobile\99\rlmenu_2088.html" has caused a runtime error in function "label". Cause of error: Var
-
How do i restore OS X to my mac?
after my mac was being excessively slow i decided to wipe the harddrive and reinstall OS X and apple aplications. I restarted my laptop holding down the command and R keys to open the disk utility. I then erased the Macintosh HD. Now i am trying to r
-
Urgent ! Speed and image size problem.
Dear Java Guru, I have the speed caused by: param.setCompression(TIFFEncodeParam.COMPRESSION_JPEG_TTN2); If use: param.setCompression(TIFFEncodeParam.COMPRESSION_DEFLATE); It will be 6 times faster, but the image size is bigger. But we need to keep t