How to Check WET610N is working?

I called and spoke to a Cisco representative and they told me all I have to do is get a WET610N and WAP610N in order to get my wireless situation set up.
We currently have the E3000N (which everyone said was the strongest router, but doesn't even go 300ft) it is connected to our cable modem.
It sends out it's wireless signal, and the Cisco representative told me if I get the WET610N to act as a wireless bridge, and then the WAP610N to act as a wireless access point we should be able to extend the wireless range.
I've set up the WET610N and the WAP610N. It claimed that everything was working correctly, that the wireless bridge was set up, etc.
I created a second SSID and it appeared to work. Then we moved the WET610N and WAP610N to their location in order to extend the range and it stopped working!
I know for a fact we are not out of the wireless range of the E3000N as I am using it to post this. The second SSID coming from the WAP610N is broadcasting and the signal is strong, but when I try to connect it says it has limited internet access, or no access.
So is something wrong with the WET610N in receiving the signal? Or is something wrong with the WAP610N? How can I check if they are working? Do I have to reconnect them to the E3000N to check? Is there a surefire way to make sure it all works?

How you have configured WET and WAP? have you setup a static ip on them or it is configured as dynamic ip? If you have setup a static ip then on your computer open the command prompt window and ping the ip address of the bridge and check if you are getting replies, If you are getting replies then the bridge is configured properly, then you need to check the settings for your AP.

Similar Messages

  • How i check ads configuration working fine ?

    Hi,
    How i check my ads configuration working fine ?
    Regards,
    Gurprit Bhatia
    Edited by: GURPRIT BHATIA on Jun 9, 2008 2:15 PM

    Thanks arafat,
    I need some more help regarding this issue. I checked that working fine as u say.
    But still my Interactive forms gives error like
    com.sap.tc.webdynpro.services.exceptions.PDFDocumentCreationException: ../../local/Test_Interactive/TestInteractive/~wd_key19_1213015656616/Error+PDF.pdf;jsessionid=(J2EE1769300)ID0821942250DB10853844897087772781End;saplb_*=(J2EE1769300)1769350?sap-wd-download=1&sap-wd-dl_behaviour=1&sap-wd-cltwndid=3c74abd1362211dd8c0f00144f411328&sap-wd-appwndid=3c74abd2362211ddb81100144f411328&sap-wd-norefresh=X
        at com.sap.tc.webdynpro.clientserver.uielib.adobe.impl.InteractiveForm.afterHandleActionEvent(InteractiveForm.java:405)
        at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.afterApplicationModification(ClientApplication.java:1132)
        at com.sap.tc.webdynpro.clientserver.cal.ClientComponent.afterApplicationModification(ClientComponent.java:895)
        at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.doRespond(WindowPhaseModel.java:573)
        at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequest(WindowPhaseModel.java:152)
    Please help me to trace this code.
    Regards,
    Gurprit Bhatia

  • How to check the generated work schedules

    Hi Friends,
    We have more than 30 Work schedule rules,  in which some of them have been generated some of not. So now I want to check which work schedules have not been generated. Kindly advice the how can I check the non generated Work schedules or generated work schedule.
    Thanks
    kl

    generally
    We use the following tcodes
    PT01  to generate
    PT02  to change the DWSR
    PT03  to display the DWSR
    more over if u have not generated the Daily work schdule you will get an Error while save DWSR in IT0007  so please check the above tcodes

  • How to check any URL working or not through Java Code

    Hi,
    Is there any way by which i can check whether any particular URL is working or not using JAVA..
    Thanks in advance......
    AJ09

    Especially for POSTs, I would use HTTPClient: [http://hc.apache.org/httpclient-3.x/]
    For simple GETs, you could just create the URL and then see if openStream works.

  • How to check / internet is working or not?

    i need to execute a line of code in java console application only and only when internet is working ie i can access the google page
    to check the internet connection , i try below code,,
    try
            URL url = new URL("http://google.com/");
               URLConnection connection = url.openConnection();
               connection.connect();
            catch( Exception ex)
                // connection can not be established
            }but here, when internet is working, try block successfully execute . when internet is down , it throw an exception on Connection.connect() ,
    connect() is void type , it is not returning anything, that's why i can not handle it.... is there any other way , where i get true or false or any number , when internet is ok, ie www.google.com is responseing..

    rohit pathak wrote:
    iwhen internet is down , it throw an exception on Connection.connect() ,
    connect() is void type , it is not returning anything, that's why i can not handle itWhen an exception is thrown, you have two choices:
    1) Catch it and actually handle it. This means whatever failed, you have to make it work. Maybe by trying again, maybe be providing a default value.
    2) If you cannot to #1, then you should not catch the exception in the first place. Or, if you do catch it, wrap it and rethrow it.
    So, for example, in your case, if your code is:
    Establish connection.
    Use connection.If the "establish" part fails, you obviously can't do the "use" part, and this overall task has failed. That happens sometimes.

  • How to check if DBlink works

     

    Prashant,
    In Sqlplus,
    Do a desc or select on a table with the dblink
    ex: select count(*) from <table_name>@<db_link_name>;
    ex: desc <table_name>@<db_link_name>;

  • Project server 2013 how to check work hours per hour per project

    Hi all,
    I would like to know how to check the total work hours for a project per month. For examples, I want to know all the work hours for all resources spent for the project A in August. Any idea?
    Thanks,
    Anna

    Hi Anna,
    If you don't want to write queries, I'd suggest you to simply open the project unchecking the option "load resources summary assignments" and go to the task usage view. Then display the project summary task and choose the monthly timeframe ("view"
    tab) for the timephased part of the screen (right part).
    Hope this helps,
    Guillaume Rouyre, MBA, MCP, MCTS |

  • How to Check BPM success or fail in SXMB_MONI_BPE ?

    Hi Experts
          Help me...and i am new to BPM
          I have done a simple BPM scenario and i am not sure it is working fine or not
         So I open TS code : SXMB_MONI_BPE and here how to check the BPM
         Working find or not ? if success means what is the response number?
         Failure means what is the response number ?
         Can any one explain me in detail....step by step of Monitoring of BPM?
    Adv thanks and Points
    Prasad K

    Hi Prasad,
      Two ways you can check your BPM has successfull or not.
      1. Go to SXI_CACHE , Double click on Integration Process Check the Return Code has 0. If return code Non-zero, select the Integration Process and activate now it will come to the Return Code is '2' again activate and you will get Return Code as '0'.
      2. Go to SXMB_MONI or SXI_MONITOR or SXMB_ADMIN
      Execute the XML message, find out your message and that message has 'PE' that means that is a BPM message.
      Click on PE you will see how BPM steps worked in your scenario where it failed exactly.
      select the particular step and In Application toolbar there is ICON called 'Technical overview' click the buttion it shows the everything.
    Regards,
    Venu.

  • How to check oracle is running or not

    Hi,
    Can any one help me the command to check whether oracle is running or not, in UNIX flatform.How to check the Disk+Work proess is running or not.

    Option1 :Logon to SAPDBA...U will be able to see whether Oracle is running or not.
    Option 2:
    Sqlplus /nolog;
    connect / as sysdba;
    startup;
    If it is already running: you will get msg that Oracle is already running
    Oprion 3: ps -eaf|grep ora
    to determine whether disp+work is running or not:
    Option 1: ps -eaf|grep sap
    Option 2: dpmon pf = <path of instance profile>
    Reward Points if helpful!

  • How to troubleshoot issues that Spell Check is not working in Outlook 2013

    When composing a new message in Outlook 2013, we may notice that Spell Checker does not recognize misspelled words. When we enter a completely garbage word in Outlook, it won’t be marked as misspelled with a red wave underline. When encountering such issue,
    we may follow the troubleshooting guide below to correct it.
    1. Make sure you are not typing in the signature area.
    Outlook doesn't perform a spell check in the signature area, so if this is the case, spell check won’t work. To confirm if you are typing in the signature area, right click in the area you are typing, if you see a menu listed all you signatures instead of
    the normal context menu, then you are not typing in the email body.
    If you want spell check work in signature area, use Quick Parts instead of Signature. For more information, see
    Quick Parts.
    2. Check the Set Proofing Language option.
    In Outlook, click New Email to open a new message, click
    REVIEW tab > Language > Set Proofing Language, a dialog titled
    Language will open.
    Please first make sure English (United States) is shown above the double line. If not,
    you must enable the language for it to be available to check spelling.
    Second, make sure “Do not check spelling or grammar” check box is not selected.
    Note: If this method fixes the problem, repeat steps 1 through 3 to reopen to the
    Language dialog box, and then click Set As Default.
    3. Enable Check spelling as you type.
    To enable the option in Outlook, go to File > Options > Mail, click Spelling and Autocorrect button. In the Editor Options dialog, select the check box labelled “Check spelling as you type”.
    4. Make sure that you are not using a standalone version of Outlook or mixed versions of Word and Outlook.
    The “Check spelling as you type” feature doesn’t work when using a standalone installation of Outlook or mixed versions of Word and Outlook. However, the manual spell check always works. In this scenario, we can set Outlook to
    always check spelling before sending. To do this, go to File > Options > Mail, select the check box before “Always check spelling before sending” in the Compose message section.
    5. A registry key exists overriding the spell checker
    To remove the registry key, please follow these:
    Important This article contains information about how to modify the registry. Make sure that you
    back up the registry before you modify it.
    a. Press Windows key + R to open the Run command.
    b. In the Run box, type regedit, and then press Enter.
    c. Locate the following registry subkey:
    HKEY_CURRENT_USER\Software\Microsoft\Shared Tools\Proofing Tools\1.0\Override
    d. Delete or rename the subkey.
    e. Exit Registry Editor. Restart Outlook.
    6. Recreate the NormalEmail.dotm and Normal.dotm template
    If the two templates above are corrupt, this issue may also happen. To fix it, please browse to:
    drive:\Users\username\AppData\Roaming\Microsoft\Templates
    Rename the two templates, then restart Outlook to see the result.
    7. Problematic add-in
    Add-ins may cause various issues in Outlook, so if you have tried all the suggestions and still no luck, try starting Outlook in safe mode to see if a problematic add-in is the culprit. To do this, exit Outlook, press Windows key + R to open the Run
    command, then type outlook /safe and press Enter. If the problem disappeared in safe mode, then go to File > Options > Add-ins and disable the suspicious add-in to resolve the problem.
    If you have any comments, welcome to post in the forum. Thank you.
    Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

    Not all locales come with a dictionary installed for licensing reasons.<br />
    If you do not have the en-US locale then check that you have a dictionary installed (Tools > Add-ons > Extensions) and selected.<br />
    <br />
    You can see which dictionary is selected if you right-click in a text area and open the Languages submenu.<br />
    Also make sure that [X]"Check Spelling" in the right-click context menu has a tick.<br />
    You can also try to toggle the "Check Spelling" item off and on again.<br />
    <br />
    See http://kb.mozillazine.org/Spell_checking and [[Using the spell checker]]<br />
    See also http://kb.mozillazine.org/Dictionaries<br />

  • Spell Check in New Forums- How The Heck does it work?

    Can somebody please tell me how the spell check works in this new forum format? I click on the abc icon and it does nothing. I do a two finger click on a word that is misspelled and it give me Insert Options. I really like the new format but hate the spell check. Can anyone offer advise? Thanks.

    The built-in ASC spell checker is -- to put it kindly -- quirky. First, you must turn it on using the 'abc' tool on the right in the editor toolbar. (When it's on, it highlights.) But it won't stay turned on if you click on the tool before you enter any text -- it will just tell you that no misspellings were found & won't stay on. It also sometimes fails to check the last word if followed by a space. You can tell it to ignore misspellings, but you can't tell it to learn words because the spell-checking dictionary is actually on the servers running the site, not on your Mac or PC.
    But from your remarks, you probably aren't even using the built-in checker. Instead, I suspect you are trying to use the far superior system-wide one built into OS X. The problem with that is the ASC editing tools are powered by Javascript supplied by the Jive SBS software running the site. Because that is platform independent it doesn't know anything about OS X's contextual menu (which includes suggestions for misspellings, the Dictionary lookup, & so on).
    So to make a long story short, what happens when you try to right click on a word the OS X checker has underlined in red, instead you get the Javascript's response to a right click, which brings up the editor's insert/alignment popup menu instead of the OS X contextual menu.
    The solution is to control click on the word -- believe it or not, within the ASC editor window a right click & a control click are not the same thing! You literally have to hold down the control key on the keyboard when you click to bypass the Javascript's right click response.
    To make things that much more confusing, this only applies if the pointer is not over empty space in the editor window, which in this case excludes lines that have any text on them, including invisible text like spaces or returns. (To see what I mean, drag the tab at the bottom right of the editor window down so there is a lot of empty space below what you have typed. In this empty area, right & control clicks both bring up the OS X contextual menu, but anywhere in the text you have typed, they behave differently.)
    In short, the problem is not that Apple has changed how the buttons or clicks work, it is that the new software that runs the site (not developed by Apple) does.
    Hope this helps.

  • I synced my iphone 3 to my pc and i had about 90 songs on it and when i looked at my phone to check if it worked, it deleted about 80 of the songs, what happened to them and how do i get them back

    I synced my iphone 3 to my pc and i had about 90 songs on it and when i looked at my phone to check if it worked, it deleted about 80 of the songs, what happened to them and how do i get them back

    You might have better luck in the iPhone community. I'll ask the hosts to relocate your post.
    iPhone community
    Have you tried syncing the iPhone to your computer and restoring from the backup to see if you can get your other songs back? If you purchased the new album with your Apple ID, you should be able to download it to your computer to sync.

  • How to check if my all speakers are working or not?

    Hey ,wanted to know how t ocheck my speakers are working or not properly.model DV 66121 tx ,with beats enabled.i think my 1 speaker is not working ,how to check ?thank you guys.

    I Bought an Iphone 5s On a shop How Will I Know If Its Fake or not
    THANKS
    <Personal Information Removed by Host>

  • How to check user profile service working in sharepoint 2013?

    HI All,
    How to check user profile service working or not in sharepoint 2013? Thanks.

    Hi,
    Select which OU's you want to synchronize, then check if all users in those OU's have a user profile in the user profile service application.
    Nico Martens - MCTS, MCITP
    SharePoint 2010 Infrastructure Consultant / Trainer

  • How to check if the GPS Antenna works?!?!?

    Dear all,
    I've a "small" problem.
    As most of you have experienced I cannot fix the signal from the satellite.
    I tried everything...45°, open sky (I tried even in open sea!!!) etc...
    So my doubt is the following: how can I be sure that my antenna is working?
    Do you know if a SW to verify it exists????
    Do you know how to check it???
    If yes, pleaseeeeee tell me!!
    cheers
    MArco

    No - there's no software which can tell whether the GPS antenna is working or not. Within Maps v2 in the bottom right hand corner there is an indicator which will let you know once it has obtained a satellite lock - but not whether the actual hardware is working or not.
    Having said that I have never come across any instances where the GPS antenna has not worked on a phone. What phone do you have ?
    You should definitely have got a lock after 3 hours !
    It is definitely worth checking your settings. Make sure you quit Maps before doing this.
    Goto the menu, click Tools then Settings.
    Then click General and choose Positioning.
    Within here click Positioning methods.
    Ensure the options below are ticked :
    - Assisted GPS
    - Integrated GPS
    - Network based
    However please be aware that for Assisted GPS and network based, your network operators will charge you for any data transmitted.
    Then load Maps again and give it some time to get a lock.
    Please let me know how you get on.
    Regards,
    Edward

Maybe you are looking for