How to compare two different characteristics at the same time in polestar

Hi Gurus,
I would like to analyse the e fashion universe in polestar with comparison of previous year product line with current year product line at the same time.
is there any way to do that we can compare two years of the product line sales revenue at the same time with comparison chart like 2003 T shirts vs 2002 T shirts
in polestar we can compare the two measures at the same time but i want to compare the sales revenue of product lines of two years in a comparison chart at the same time.
Regards and thanks
Abid Paul

Hi Stratos,
I am actually able to compare the Measures but i want the comparison between the two different characteristics like this year productline vs last year productline at the same time with say one measure like sales revenue or any other.
Is it possible to compare the both and it should represent in the chart as well at the same time.
In the polestar i can compare three measures at the same time but i want to compare characteristics like year 2009 productline VS 2008 productline with one measure say sales revenue.
I would really appreciate if you could help me out.
Regards and thanks
Abid

Similar Messages

Control two different parameters at the same time

Two motors were connected each other rigidly. One motor controlled torque and the other motor controlled speed. I generated some torque and speed data which represented one cycle of motion from a motor simulation. I like to send these two different data sets (torque and speed) to two different motors at the same time. Torque data sends to one motor and speed data sends to the other motor to see the response of the load profile. In order to do this, I thought about using multithread, but I am not sure it will work for this application. Usually multithreading delay the CPU time so the overall control process might be delayed, right? If you have better idea, please let me know.

If you are using one motion controller to control both motors, you will probably run into problems if you try to use multithreading on the PC. However, you can execute up to 10 programs (threads) at a time, in addition to host communication, using on-board programming. For more information on on-board programming please refer to the following tutorial: Developer Zone Tutorial: On-board Programming in FlexMotion
Best wishes!
Dawna P.
Applications Engineer
National Instruments

Collecting data from advantech-usb4704 with two different apps at the same time

I wonder if I can access to Advantech-4704 with two different applications at the same time?
I use this block in my vis.
I have enough ports, but inputs are needed in completely different applications. Do I have to close one of them or can they run simultaneously?
Thankyou!

Dear gtu,
as nathand said, usually it is not supported to access the same physical resource simultaneously from multiple programs. In case of DAQmx for instance, you will get an error message which says that the resource is already reserved. I suppose the same would happen with your driver, however it might be worth a try.
One workaround could be however if you revise your applications and merge the codes if it is possible so that no concurent resource allocation takes place.
Best Regards,
Adam Cseh
Applications/Systems Engineer
National Instruments

HT204380 Can you FaceTime two different people at the same time?

Can you FaceTime two different people at the same time?

No, not at this time. Feedback to Apple goes HERE, and click on the appropriate section.

How can I log into two differant accounts at the same time in two windows without the second window affecting the first.

I'm trying to log into two facebook accounts at the same time in differant windows. When ever I log into the second account in the second window it changes the login in the first window. When I hit home or any other link the first window account has been logged out and logged into the second window account. I tried installing a second copy of firefox in a differant folder that the first but it seems to use all the files of the first installation. If I can get 2 toatally seperated instalations that don't rely on the same history, cookies, cache, etc I belive that will solve my problem. Please help.
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; OfficeLiveConnector.1.4; OfficeLivePatch.1.3)

Nah, that won't work. Facebook has a feature that gets your IP Address, so as soon as you sign into one on the same computer, it changes the other login for safety purposes (say, someone was on a public library PC. They forgot to log out. Someone else logs in, and it automatically logs them out). You'll need 2 computers to do that.

How to Test two UUT not at the same time??

My test station need to test two UUT not at the same time ,Two UUT means two serial Number need to scan, and then test each UUT after scan action . The two UUT are the same PCBA,all the test items are the same. So the sequence file is same. But how to realize it in TestStand ? Can you give me a simple example for that ? Thanks so much !

Have a look at the process model options of TestStand. For your task I would use the batch model. If I remember correctly there are also some examples delivered with Teststand. Search for MultiUUT and Processmodell in the examples directory of your Teststand installation.

Is it possible to realize two different processes in the same time with TDMS?

Hello all,
we have one TDMS but a lot of workstreams. Is it possible that 2 different workstreams in the same time realize anonymization in TDMS?
Thanks in advance!!!
Ilkin Mammadov

Hello Anita,
I am sorry.I mean we have a lot of projects (for example Procurement, Finance, Logistics, etc) and each of them wants to anonymize. But it is existing just one TDMS. Can these projects start with anonymization in the same time or they have to wait till one of projects finished anonymization?
Thanks in advance!
Best regards,
Ilkin

HT2688 How to play same song of two different computers at the same time

Hi I have turned on Home Sharing. So one computer can play music on another. Is there any way to have one computer play what the other computer is playing at the same time. Other than just starting the same song as close in time as possible on each computer.

create an album of all of the photos you want to order, open the album, select all and order - be sure teh photos are cropped to the print size so unexpected cropping does not occur during the printing process
LN

How to run two vi's at the same time, one uses an AI task with 8 AI channels the other a single AI and AO channel???

Hello Everyone,
Here is my situation. I have one vi that is reading an AI task of 8 channels AI0 --> AI7 (one sample on demand) and also has control of all of the digital outputs on the board. My problem is that I want to run another vi that will use the last AI channel AI8 and an AO channel AO0. These two vi's do not need to know anything about one another but I do need them both to be running at the same time. Currently when I try running the two vi's together both vi's crash and I get an error message stating that the AI8 pin is reserved. AI8 is not part of the task and is not refrenced anywere in the larger vi. I am assuming that this problem is do to the fact that the larger vi is occupying the DAQ board, cycling through the task when the smaller vi is requesting data from AI8 and the DAQ board cannot do two things at once. The sampling rate on the smaller vi is not really that important. Is there anyway I can get the smaller vi to read from AI8 and not crash??? Software and Hardware listed below. Thanks in advance for any suggestions.
PCI-6221
Labview 7.1

Hi steve ,
Sorry to say that you cannot configure and acquire from AI channels on a Device simultaineously from 2 seperate VI's.
regards
Dev

How to make two Range Selection at the same time?

In a single clip, at the same time, in two locations, I would like to have Range Selection. Then I would like to switch between the two and play within the range one after the other immedeately. Is this possible? Thanks.

success1975 wrote:
In a single clip, at the same time, in two locations, I would like to have Range Selection.
You can mark multiple range selections in a clip by clicking and dragging with the Command key down – or marking in and out points with Shift+Command.
I don't know what you mean when you say "at the same time".
Then I would like to switch between the two and play within the range one after the other immedeately. Is this possible? Thanks.
Forward slash plays betweeen the in and out. The only way I know to play them one after the other "immediatelly" is to edit the two selections to the timeline.
Russ

How to use two different versions of the same jar within one project

Hi everybody!
I have a big problem while integrating different web service clients within one bigger java project. Both implemetations need some jar files to work but demand different version. So, i would like to know if there is any way to tell which implementation should use which version! Anyhow i add those jars to the classpath makes working only one or the other webservice working but never both! Any ideas somebody?
Best regrads,
Stefan G�tz

Of course do have the jar files different names but the classes inside of them are the same ... means that the standard system classloader can distinguish them. When you add a jar to a classpath the name actually dosent matter.... any other ideas, please?
PD.: i tryed to add a manifest file to the one jar which makes use of one of the dublicated jars to specify which jar to take direcly but it makes no difference since once classes loaded they cant be distinguish ....see:
http://java.sun.com/docs/books/tutorial/ext/basics/load.html

Is it possible to order two different cards at the same time? I do not want to pay shipping costs twice.

Hi, here's my problem. I made two different Christmas cards that I want to hand over in person. When I order one however, I can not select the other one, despite the fact that I want them both delivered to the same adress. Is there a way to order both as a bundle?
Thanks a lot
Best, Stefan

Afraid not.

Keys playing two different sounds at the same time

I keep getting one of the synths whenever I'm playing the Pop Kit, or any drumkit, with my MIDI. Basically when I hit a key, two sounds come out of it when it's only supposed to be one. I've rebooted GB and the MIDI with no success. How can I fix it?

That's weird - never heard of that phenomenon. Could it be that the second sound is coming out of your keaboard? What's your setup?

How tp compare two different programs

Hi ,
I have created a copy of a standard report , but both are giving outputs in different ways , the layout of the newly created report is distorted .
Can someone advice of there is any way to compare two different reports in the same environment
Regards
Ashish

Hi
As I m new to this transcation ,
Can you please advice what parameters do i need to enter to compare the std report & Z report in tcode SCu0.

Time Division Multiplexing and Processing Different Loops at the same time

Hi, I am new in Labview so you may find my questions too silly, sorry about that
I want to design an interface to control the test&measurement devices remotely. I have two desks and there are several devices on these desks. The real problem is to use two different devices at the same time. To do this I heard that I can use time division multiplexing. But I couldn't find enough information about it in Labview. Another advice I heard was to use a matrice and hold the on/off state of the devices in this matrice.
Where should I start the design to create such a system? Do you have any advices? Thank you in advance.
My basic GUI is attached.
Attachments:
InterfaceAli.zip ‏42 KB

As Mike pointed out you cannot communicate in parallel on the GPIB bus - unless you have separate buses for each instrument - and that defeats the purpose of a bus. I am not sure about LXI.
With regard to your VI:
1. Do not use global variables to pass your data around.
2. You should use the Array data type, not the Matrix data type. The Matrix data type in LabVIEW should only be used for matrix mathematical operations (linear algebra) which cannot be easily performed on the array data type. You have many more tools in LV to work with arrays.
3. The Event structure needs to be in a parallel loop. This is basic data flow. If you do not understand this concept, get some training, either though the online tutorials or through a class.
4. Use Value Changed events and place the button terminals inside the event case for that control.
5. The parallel loops need to have a Wait or some other function which causes a delay. Otherwise, the first one to start executing could consume all available processor resources. These are called "greedy loops."
6. Use integer data types for case structure selector inputs. Floating point values are coerced to integers at the inputs. If the values resulted from calculations, unexpected rounding effects may occur, resulting in the wrong case being selected. In some cases using type defed enums may be even better. The underlying data is integer and the enum item names show up in the case selector labels, helping to document what the case does or why it was selected.
7. Remove the timeout case from the event structure since it never executes. Also avoid Use Default if Unwired on the terminal with your matrix (array) data. You never have a situation where an empty array is appropriate.
Before going any further with the program questions, you need to carefully define your requirements. How many instruments will you have? How many can be active at one time? What kinds of communication between the program and the instruments is required? This includes commands to the instrument, data returned from the instrument, error handling, and timing requirements. What will be done with the data? Display, save to file, use to automatically control another device? What safety requirements or constraints need to be met? Once you have a good requirements document, then you can begin to determine what kind of program architecture is best suited to meet the needs.
I suspect that you may be making some things much more complicated than they need to be while ignoring other important issues.
Lynn

How to compare two different characteristics at the same time in polestar

Similar Messages

Maybe you are looking for