How to configure a P2000 MSA Array System Dual I/O - Help Needed
Hi, Tried to install a new HP P2000 MSA for a client today. We are connecting the P2000 directly to SAS Card in our HP Server.
Installed 2 x 3TB drives no problem. Drives show up in the BIOS and in VSphere no problem.
We want to setup a new RAID 1 array using the new SAN. I assumed running the array config (F5) on boot would allow me to create the array, but HP Smart Storage does not see the new device or drives.
I spent hours looking online for assistance. Any HP docs mention connecting to the SAN by CLI or Ethernet port. Neither of which we have on the SAN. We have two separate IN/OUT SAN connections which we have connected to our SAS card in the Server. I have also seen suggestions to use the SMU to configure RAID in the new array. Again, I cannot see how to access or run the SMU.
How can we configure RAID on the device if the HP SMart Storage software cannot see the device. Completely stuck here so any help appreciated!
Thanks.
Hi:
You may also want to post your question on the HP Business Support Forum -- Storage Area Networks (SAN) (Small and Medium Business) section.
http://h30499.www3.hp.com/t5/Storage-Area-Networks-SAN-Small/bd-p/bsc-257#.VQoKWDgtHGg
Similar Messages
-
How to Configure client 001 to logical system in trial netweaver abap?
Hi,
I have downloaded and installed sap netweaver abap trial version in my pc. I want to configure client 001 and assign it to a new logical system in it. I do not know how to do it as it is a prerequisite for BI. Kindly provide me steps to configure it.
Thanks in advance,
Regards,
KannanHi
You need to follow some steps in both the systems
R3 side
http://help.sap.com/saphelp_nw2004s/helpdata/en/27/8d8342a7d30d53e10000000a155106/content.htm
BW side
http://help.sap.com/saphelp_nw2004s/helpdata/en/ac/4a4e38493e4774e10000009b38f889/frameset.htm
Hope it helps
Thanks,
Teja -
How to configure Dotmatrix Printer in local system
Hi,
I need to configure DOT MATRIX Printer in Local System in ECC6.0. please give steps how to configure.
Thanks,
venkatThis is not more different than other printers.
check
http://help.sap.com/saphelp_nw70/helpdata/EN/7e/36e4c4023411d399b70000e83dd9fc/frameset.htm
Markus -
How to configure Use tax in the system
Hi ,
As in use tax , the tax amt should be paid by the buyer to the govt... we r using taxware... so let me know how to configure the tax codes.. normally the entries will be expenses dr, tax dr and the full amt will go to vendor cr.... but here the vendor amt should be exclusive to the tax amt.... please let me know the process..
ThanksHi,
Muscan in this scenario whenever you are posting the invoice for the vendor you may get the field called EDITING OPTIONS from there u can select check box of calculate taxes on net amount in the general entry options tab.
I hope it will helpful to you................ -
How to configure in Charm in three system landscape
Hi Experts
I want to configure the charm in the three system landscape system. Please help me to configure
Thanks & RegardsIt is same whether it is two or it is three system landscape, i guess you already must have gone through the following
charm setup
Re: Can Any one Provide Step by Step Config of CHARM??
http://sap.ittoolbox.com/groups/technical-functional/sap-basis/charm-in-2tier-system-1231210 -
How to install xp on windows 7 system (dual boot)
Hi all!
I have Lenovo s10-2 with 3G module and Windows 7 start edition originaly installed on it.
Beacause the system is very slow I want to install xp home via usb. And I woud like to have both systems working.
Is the any tutorial how to do it? And what software I need for doing it?
Thanx in advance!With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR suitable for your PC (there's a 32-bit Windows version and a 64-bit Windows version):
http://www.rarlab.com/download.htm
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you? If so, see if iTunes will launch without the error now.
If instead you get an error message during the install, let us know what it says. (Precise text, please.) -
How to configure the bios of the big bang marshal p67 (help)
Good afternoon people I'm new here, I hope to be posting in the correct forum, and come on, I recently bought a Big Bang Marshal P67 B3, I'm using a vcore [email protected] to 1:42 daily and a kit of 2200MHz 2x2GB Gskill PIS, but whenever I play the machine locks up and has the blue screen, I'd love your help on all the settings I need to do to leave my bios over 100% stable.
Thanks in advance for help.Quote from: HU16E on 04-August-11, 11:28:03
Right click 'Computer', then left click 'Properties', 'Advanced system settings', 'Startup and Recovery' 'Settings', uncheck 'Automatically resart'.
Disabled.
Thanks buddy, now I found.
I'll take and post all the screens of my bios, if possible tell me if you configured everything right or if I need to change something ok.
Every time I try to run prime95 linx or just going to play, does not take long to see this screen. -
System won't load (help needed)
Hello!
I have a PIII 600 computer which I don't really need, but I decided to make any use of it with Archlinux. The problem is that even before I cleared my hard drive, the only thing I had been able to load on it was Windows ME in a safe mode (I don't know if that's the correct name for this mode, as I was using Polish language version).
But I managed to run the Arch installer using acpi=off option. Now, when I turn the computer on, I can see the Grub menu, but no matter what I choose, the system stops loading and just does nothing. I had the same sympthom when I used the installer without acpi=off option (or with any other).
Can anybody tell me, what kind of problem (I guess it's my hardware) do I have? Is there a way to run the system I have installed right now, maybe using command line in Grub?
Some additional info: I have 128MB SDRAM DIMM (Windows was saying it was 126, but my bios finds more than 131 000 bytes), SoundBlaster 128, nVidia Riva TNT2, 17-inch LCD working at 1280x1024, a PCI wifi card, a radio ISA card. I can't run Archie nor memtest.
Thanks in advance for any ideas.Wiki is your friend - http://wiki.archlinux.org/index.php/Main_Page
I do not mean to be mean, it's simply inefficient to try and answer all the questions you _will_ have while trying to configure Arch to your liking, especially since Wiki covers most of them, and covers them well. If you come across a problem that's not covered in the wiki post here and we will definitely try and help you -
hello all,
I have not work a lot on SAN storages. One of my client has implementated 9i RAC. Now he wants to Add two more disk in SAN storage (Implemented RAID). So sun engineers will do this but before this i have to take full database backup(80GB database) throught RMAN. The problem or confussion from my side is that the database is on Sun SAN storage and i have to put the Full database backup taken by RMAN on local hard disk on the node (node 1 of rac). Is the possible since the SAN storage is RAW file system (as i guess) and i am putting the backup on local system.
Please help me out ...i have do this in couple of days..
Please tell me prosedure too to how to change the path of backup in RMAN if above is possible..
Its urgent
Thanks and Regards!!
Pankaj RawatYou best bet is to get your san folks to give you some disk space for a mount point on the last node in the cluster. Once they assign the lun (not raw) have your SAs make it a mounted file system such as /dbbackup.
Run all of your rman backups on your last node on the cluster. The only draw back is, if that node dies, then you will not be able to run backups. but your backups would be safe as they are on the san.
Only way to have a mounted file system on all nodes in your cluser is to have some sort of third party file system cluster ware .. such as veritas or OCFS2 - then all nodes could see it.
I feel the first node in the cluster (the primary node) is the most busy out of the rest .. so thats why the suggestion of running rman on the last node in the cluster. -
3-d array to xlsx file (excel) - help needed
Hi guys,
i've a question for you...
i would save an excel file (.xlsx) having as input my 3-d array...i would that first dimension are my excel worksheets and then the other 2 dimensions are the data inside each worksheet.
I know that there is the report generation toolkit, and i would use it....but i don't know in which way
could you help me?
Many thanks and nice holidays!
PS: i use labview 2009Gianluca1985 wrote:
Many thanks and nice holidays!
Curious... what holidays?
Go here and click the Download button.
It's pretty easy to use and the VIs are very straightforward. You probably want the Excel Specific VIs Excel Easy Table and Excel Add Worksheet.
Report back after you've played around with the toolkit a bit.
As far as the 3D array goes, you're going to want the first subarray to be the worksheets (it will actually be a 1D array of worksheet names, right?), so you would index your array twice to get a 1D array of strings.
Next to get each set of data, you're going to get the Index 1 value from the array and so on. Index 1 will be a 2D array data for the first worksheet, Index 2 will be the next 2D array and so on. -
My phone broke , I have recently got a new replacement but how can I get my photos from the old to the new phone
Did you have the old phone backed up? If not, then you don't. If so, you restore the backup of the old phone to the new one.
-
How to conf in Hyperion, so the system couldn't login with the same user
Hai.....
how to configure in Hyperion, so the system couldn't login with the same user id in different machine ? (could you please provide me with detail step by step ? )
rgds
uka fpfane_j wrote:
Sally R. wrote:
Someone gave me a suggestion to go to the terminal and type in the following:
ls /Users/Shared/.*.so
This was published on MacWorld's site, and it's not a very good tip. Try this instead
ls -la /Users/Shared/*.so
Turns out I was wrong about that. Somebody else suggested something even more complicated and got this reply:
By bastion
Fri Feb 24 08:49:05 PST 2012
PeterSParker said
Your terminal statement has an extra "." in it that prevents it from working.
Also, you should add the options -alR to show what is happening, and to search subdirectories.
The revised command looks like this:
ls -alR /Users/Shared/*.so
The above is completely wrong. The command as shown in the article is appropriate.
The "." is not extra and doesn't prevent the command from working. It's specifying that you're listing files that start with a period and end with ".so" with anything in between being matched.
Because you're explicitly searching for things that start with "." you don't need the -a flag.
Because you only care about simple existence and not any metadata you don't need -l.
Because the files of interest are installed in /Users/Shared directly, and not subfolders thereof, you don't need -R. -
How to configure mail server for subscription
Hi,
I want to test subscription. My problem is how to configure the mail server.
As to my understanding, we need first configure mail server, then the user can choose "Subscribe" in the Details screen of a folder.
My steps are:
1. In KM - CM - Utilities - Channels, specify SMTP server, userId and password.
2. In KM - CM - Utilities - Channel originators, set the Original address for notificator.EMAIL.
3. In KM - Collaboration - Groupware Transport - Mail Transport, specify SMTP server and sent message folder.
After that, when I choose a user and click "Send email", it failed saying "Failed to communicate with SMTP server when sending the email.".
Could anyone tell me what's wrong with my configuration, or what should I do to make subscription work?
Thanks,
RayHi Vineeth,
Thanks for help.
According to your steps:
1. set up a mail transport and making notification and mailing service active.
In System admin - KM - CM - Global services, I've enabled Inbox, Mailing and Notification services.
In KM - CM - Collaboration - Groupware Transport, I've set up a mail transport:
Name: JavaMailTransport
SMTP Server: smtp.yahoo.com
Sent message folder: /documents
System alias name: mytransport
2. Give everyone read permission on notifications in KM.
Where can I set user's permission on notifications? I think you mean folder /etc/notifications, but I don't know how to set permissions.
3. Check if proper id's are maintained in users profile.
How to do this?
Thanks for help~~
Regards,
Ray -
Configuring Netweaver administration on SLD system
I have SLD configured in our landscape. I can see all systems in the system . Does anyone knwo how to configure NWA adminstration on same system to admin all the systems through SLD ? Any pointer to white paper or OSS note will be helpful .
I am seeing messages
at NWA overview screen
System Landscape Directory is not accessible
Only local system can be administeredHi,
1. You will need following roles/authorizations to be able to administrate SLD:
SAP_J2EE_ADMIN
SAP_SLD_ADMINISTRATOR.
2. You need run RZ70 on each satellite system in order to get them connected to your SLD server.
3. I have some SAP documents please leave your e-mail here so I can send.
PS. If you think the answer is helpful, please consider to reward points.
Thanks,
Yujun Ran -
How to configure additional action
Hi,
How to Configure additional action in a system where only one action is allowed for an employee in same day in IT0000, and what is the purpose of IT0302.
it will be helpful if any one shares the steps.
Thank you
SrihariHi,
Infotype 0302 Additional Actions allows you to automatically log all of the personnel action types that are performed for an employee on a specific date. It allows you to perform and document several personnel action types for an employee in the R/3 System on the same day.
You can display and edit the data records logged in the infotype Additional Actions (0302) on the list screen of the infotype Actions (0000),
In Customizing for Personnel Administration, choose menu path Setting Up Procedures -> Actions -> Set up personnel action types to specify, among other things, the following:
whether you want to use the automatic logging of personnel action types in the infotype Additional Actions (0302)
which personnel action type should be saved, that is preserved, in the infotype Actions (0000) if you perform another personnel action type for the employee on the same day.
You can check the link below for detailed procedure for config:
http://help.sap.com/saphelp_46c/helpdata/en/dd/234b6e5733d1118b3f0060b03ca329/content.htm
Hope it helps!
Arpita
Maybe you are looking for
-
Organizing music with iTunes Problem
Hi, I had downtime today at work, and I decided to organize my iTunes library. However, some tracks are showing up on the same album, but not grouped together. I have selected every option possible in the Get Info menu. I have done all I can think of
-
- Now only FF banner appears at top with tabbing ok. - Search windows gone too. - Some sites unable to open documents for Adobe even after uninstall and reinstall. - Have uninstalled/reinstalled FF - FF started in safe mode seems OK but then regular
-
Downloading older versions for pc's with no internet
Hi I need an older version of Adobe Reader to install into a old laptop that has no internet connection. I saw something similar on other threads but for the current version instead, but because the laptop is so old the current version won't run on i
-
LDAP (OID) search fails on binary data
Hi People, I am trying to perform OID search with filter like this: "(&(cn=test*)(usercertificate=*))" and getting error: javax.naming.OperationNotSupportedException: [LDAP: error code 53 - Function Not Implemented]; remaining name '' (if perform pro
-
Read Directory Listing of a password protected Folder
Hello all, I am using an Intranet, and I want to read the directory listing of a password protected Folder, which is located onto an other computer. Thanks Geotos