How to configure an ASA with 2 Public IP address.

Hi, I have to configure a router ASA 5505 with 2 Publics IP, our ISP give us a 3 Public IP, and actually our configuration is like this:
interface Vlan1
nameif inside
security-level 100
ip address 192.168.x.x 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 200.91.x.x 255.255.255.248
The problem is: If I create a new Vlan, the interface overlaps.
How can I solve that problem??
Thanks for your answers!!!

Answered in duplicate post:
https://supportforums.cisco.com/discussion/12150111/how-configure-asa-2-public-ip-address

Similar Messages

How Can i Use two Different Public IP Addresses no my DMZ with ASA Firewall.

How To Using Two Different Public IP Address on My DMZ with ASA 5520
Postado por jorge decimo decimo em 28/Jan/2013 5:51:28
Hi everyone out there.
can any one please help me regarding this situation that im looking for a solution
My old range of public ip address are finished, i mean (the 41.x.x.0 range)
So now i still need to have in my DMZ another two servers that will bring some new services.
Remember that those two server, will need to be accessable both from inside and from outside users (Internet users) as well.
So as i said, my old range of public ip address is finished and we asked the ISP to gives some additional public
ip address to address the need of the two new servers on DMZ. and the ISP gave us the range of 197.216.1.24/29
So my quation is, on reall time world (on the equipment) how can i Use two different public ip address on the same DMZ
on Cisco ASA 5520 v8??
How my configuration should look like?
I was told about implementing static nat with Sub Interfaces on both Router and ASA interface
Can someone please do give me a help with a practical config sample please. i can as well be reached at [email protected]
attached is my network diagram for a better understanding
I thank every body in advance
Jorge

Hi,
So looking at your picture you have the original public IP address range configured on the OUTSIDE and its used for NAT for different servers behind the ASA firewall.
Now you have gotten a new public IP address range from the ISP and want to get it into use.
How do you want to use this IP address range? You want to configure the public IP addresses directly on the servers or NAT them at the ASA and have private IP addresses on the actual servers (like it seems to be for the current server)?
To get the routing working naturally the only thing needed between your Router and Firewall would be to have a static route for the new public network range pointing towards your ASA OUTSIDE IP address. The routing between your Router and the ISP core could either be handled with Static Routing or Dynamic Routing.
So you dont really need to change the interface configuration between the Router and ASA at all. You just need a Static route pointing the new public IP address towards the ASA outside IP address.
Now when the routing is handled between the ISP - ISP/Your Router - Your Firewall, you can then consider how to use those IP addresses.
Do you want to use the public IP addresses DIRECTLY on the HOSTS behind the firewall?This would require you to either configure a new physical interface with the new public IP address range OR create a new subinterface with the new public IP addresses range AND then configure the LAN devices correspondingly to the chosen method on the firewall
Do you want to use the public IP addresses DIRECLTY on the ASA OUTSIDE as NAT IP addresses?This would require for you to only start configuring Static NAT for the new servers between the inside/dmz and outside interface of the ASA. The format would be no different from the previous NAT configuration other than for the different IP addresses ofcourse
Of the above ways
The first way is good because the actual hosts will have the public IP addresses. Therefore you wont run into problems with DNS when the LAN users are trying to access the server.
The second way is the one requiring the least amount of configurations/changes on the ASA. In this case though you might run into problem with DNS (to which I refer above) as the server actually has a private IP address but the public DNS might reply to the LAN hosts with a public IP address and therefore connections from LAN could fail. This is because LAN users cant connect to the servers OUTSIDE NAT IP address (unless you NAT the server to public IP address towards LAN also)
Hopefully the above was helpfull. Naturally ask more specific questions and I'll answer them. Hopefully I didnt miss something. But please ask more
I'm currently at Cisco Live! 2013 London so in the "worst case" I might be able to answer on the weekend at earliest.
- Jouni

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

Hello, since nobdy else has replied...
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

How to configure bt mail with icloud?

how to configure bt mail with icloud?

iCloud does not handle any mail systems except for its own. BT is not an iCloud mail system, so you can't.

Qosmio F60-L10 - How to configure tv tuner with integrated antenna?

good evening,
i have a notebook toshiba qosmio f60 ,i had read your answer about tv tuner.
my question is : how to configure tv tuner with integrated antenna? thanks

Hi 3171954,
I think Paolo30 is right. Qosmio F60 is equipped with internal DVB-T but in some cases you need an external antenna to pick up the low signal. In most cases only in large citys you dont need an external antenna. If you live on the fringe of the city, normally a cable is needed.
Anyway, do you mean an external antenna or external DVB-T receiver (USB stick)?
Normally Windows media center should recognize the internal DVB-T tuner. Is it listed in device manager? Did you update the driver?

How to configure portal server with the Backend Oracle database

Hi Portal Experts,
we are planning to install Netweaver 04s sp stack 9 full java edition with Oracle 8i on windows platform.
we have the installation docs of portal but we didn't have any idea about how to configure Portal server with the Backend Oracle database at the time of installation or after ost installation of portal.can anyone provide the documentation about this or guide me how to achieve this.
PLZ share ur views---your help would be highly appreciable.
Regds
Phani.

HI
if you r working in Sap enterprise portal use for connection url
jdbc:sap:sqlserver://ilsql01.tlv.sap.corp:1433;DatabaseName=Northwind
ilsql01.tlv.sap.corp:1433 this is your portal url with port number
Northwind is your database name.
for dirver you need to give
com.sap.portals.jdbc.sqlserver.SQLServerDriver
in case if you r working on other than sap say windows along with oracle try to use
Connection URL as jdbc:oracle:<drivertype>:@<database>
Driver name as oracle.jdbc.driver.OracleDriver
ex jdbc:oracle:thick:@localhost:3036:mydb
Oracle implements two types of JDBC drivers:
Thick JDBC drivers built on top of the C-based Net8 client, as well as a Thin (Pure Java) JDBC driver to support downloadable applets. Oracle JDBC drivers are used to create JDBC applications to communicate with Oracle databases.
Oracle extensions to JDBC include the following features:
Data access and manipulation
LOB access and manipulation
Oracle object type mapping
Object reference access and manipulation
Array access and manipulation
Application performance enhancement
*************if the information is helpful to you please reward points************

How to configure IIS webserver with weblogic so that I can invoke servlets without the .wlforward extension

How to configure IIS webserver with weblogic so that I can
invoke servlets without the .wlforward extension
As per the documentation iisforward.dll is registered as a filter and .wlforward
has also been
included as a special file type. However this requires me to key-in ".wlforward"
after my servlet name.
What I want is something like this
http://iis/MyServlet
Please help me find a solution to this
Thanks,
Rishi

I am able to invoke the servlet without the wlforward extension now.
However, now I am required to add /weblogic before the servlet
name otherwise it does not execute the pathtrim property.
I have tried with the pathprepend thing also.
Can we get rid of the /weblogic part also. I just want to execute
my servlet as http://iis/myServlet.
Your help in this regard is greatly appreciated...
Thanks..
"Rishi" <[email protected]> wrote:
>
Thanks for the reply Kumar.
I did follow the instructions as given in the Weblogic documentation
The documentation said to add iisforward.dll as a filter service
and register .wlforward as a special
file type to be handled by iisproxy.dll. For this,
while configuring the IIS server in the Home Directory tab
I added an extension ".wlforward" and the executable as
iisproxy.dll. Is this the way it should have been done...
I also modified the iisproxy.ini file as per the documentation.
I have added the WLForwardPath property and set it to /weblogic.
My server works fine when I give the url as
http://iis/myServlet.wlforward
but it does not work for
http://iis/myServlet and this is the way i'd want it to work.
Please tell me if I am missing something on the configuration part
and if there is something special that needs to be done. I shall
be grateful to you.
Kumar Allamraju <[email protected]> wrote:
http://e-docs.bea.com/wls/docs61/adminguide/isapi.html#101184
Rishi wrote:
How to configure IIS webserver with weblogic so that I can
invoke servlets without the .wlforward extension
As per the documentation iisforward.dll is registered as a filter
and
.wlforward
has also been
included as a special file type. However this requires me to key-in".wlforward"
after my servlet name.
What I want is something like this
http://iis/MyServlet
Please help me find a solution to this
Thanks,
Rishi

How to configure ASA5512X DMZ with a Public IP address?

Hi;
I hav a ASA5512X firewall with 6 interface, interface 0 has been assigned to a WAN connectivity with ADSL, in which my ISP gave me two static IPs (not a block range of IP), my ISP mapped the Mac address of an interface to a ip address, this is what they called "Dynamice-Static" which is likely you research a mac address of an device on DHCP server, then it always giving you the same ip address.
Here is the scenario, in order to have the 2nd static IP, I need to give them the mac address of another interface on ASA5512x. I am thinking to give them the interface mac address of interface #3, however; the public ip address assigned to interface 0 is a WAN and the public ip address assigned to interface 3 will be on the same subnet from ISP, in this scenario, any problem and limitation, also; can I create a nat to translate the public ip on DMZ to one of the host in inside LAN?

What are you trying to do? What is the purpose of the second public ip? You can use that guy for any number of things. One to one NAT for one thing or another is most common [mail server, web server, RDP terminal, ect]. All of those would go over the same interface to get out to the internet.
Dynamic-Static is PAT. One IP address, multiple clients using different ports. Simliar to NAT, but different in how the translation is handled.
http://www.cisco.com/c/en/us/td/docs/security/asa/asa82/configuration/guide/config/nat_dynamic.html#wp1078939
SOOOO To answer what you are asking, just give them the MAC of the Interface 0. You can't have overlapping IPs on the interfaces. Won't work. Also if nothing is plugged into that interface, that IP won't do you any good. You could have a DMZ switch that your ASA and ISP link into, and have that second IP assigned to a device you plug into that DMZ switch. I've had to do that with some VCS servers to get Jabber working on it.

How to configure SharePoint HNSC with a reverse proxy server so that HNSC Share Point URLs are not exposed to end users.

Could you please let me know how SharePoint HNSC can be configured with a reverse proxy server so that HNSC Share Point URLs are not exposed to end users.
In normal path based site collections/web applications, reverse proxy configuration can be done using alternate access mappings with Public URL = "proxy URL", internal = "HNSC Share Point URL" so that share point sends response back
to Public URL = "proxy URL".
In Host Named Site Collections, alternate access mappings are not supported. Each HNSC is designed to have only one URL in each zone. Zone is one of the five zones(Default,Intranet,Internet,Custom,Extranet) with each of which only one alternate
URL is associated. This is what we are able to get using power shell command "Set-SPSiteUrl", but this will not help us to get the response back to proxy URL after a request sent to share point because we could not find any mechanism in share
point HNSC to respond to a different URL(proxy URL). Consequently, Share Point URLs are exposed to external users.
Below share point article in MSDN blog is symmetrical to what we are observing with Share Point 2013 and Proxy Server. It mentions that internal HNSC URLs can’t be hidden using any proxy server. If hiding the internal Share Point URLS is a requirement,
it suggests to use a web application instead of host named site collections.
Though I’m also observing the same behavior with Share Point 2013 HNSC, Could you please confirm my understanding is correct.
http://blogs.msdn.com/b/kaevans/archive/2012/03/27/what-every-sharepoint-admin-needs-to-know-about-host-named-site-collections.aspx
Excerpt from above article-
"Host Named Site Collections Only Use One Host Name
Continuing on the discussion on AAMs and host named site collections, you cannot use multiple host names to address a site collection in SharePoint 2010. Because host-named site collections have a single URL, they do not support alternate access mappings and
are always considered to be in the Default zone. This is important if you are using a reverse proxy to provide access to external users. Products like Unified Access Gateway 2010 allow external users to authenticate to your gateway and access a site
as http://uag.sharepoint.com and forward the call to http://portal.sharepoint.com. Remember that URL rewriting is not permitted. Further, a site collection can only respond to one host name. This means if you are using a reverse proxy, it must forward the
calls to the same URL. If your networking team has a policy against exposing internal URLs externally, you must instead use web applications and extend the web application using an alternate access mapping."<u5:p></u5:p>

Hi Satish,
You are right that only one URL is allowed for each zone of the host-name site collections in both SharePoint 2010 and SharePoint 2013.
It is by design that each host-name site collection only support one URL for each zone.
The article below is about RTM version of SharePoint, and it is the same for SharePoint 2013 with the latest CU.
https://support.microsoft.com/en-us/kb/2826457
So to make the URL of HNSC not exposed to external users is not supported, you need to use path-based sites instead.
Best regards.
Thanks
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

How to configure home network with Airport Extreme + D-Link DIR-665

*hello everyone,*
*I had these two working fine together until the D-Link took a dump the other day. No explanation. Just stopped working until I reconfigured everything.*
*Which then led to my Airport Extreme being unable to connect to the network at all, much less the internet...*
*My home network is set up like this:*
*Optimum Cable*
*Motorola Surfboard modem --> D-Link DIR-655 (via ethernet)*
*- Provides wifi and ethernet connections on one side of my house*
*DIR-655 --> Airport Extreme (via ethernet run to other side of house)*
*- Provides wifi and ethernet connections on the other side of my house*
*My MBP won't connect to anything other than my AE running N, so I have that set up primarily for my MBP over wifi, while feeding an ethernet connection to a Netgear router running B/G, for my iPhone and other devices.*
**So here are the relative details:**
*I decided to start fresh and do a factory default configuration with my Airport Extreme. My working system from earlier was essentially it's own wifi network, but the airport utility 'insists' that I need to run my AE in bridge mode. I've tried that, but I can't get online. I can see my shared connections, so something's getting through, but I cannot connect to them, in addition to being unable to get online.*
*I'm not really sure how to best illustrate this problem, so I've ran through the process again and jotted down a few notes. Excuse the rambling nature of my narrative, this is a 'blow by blow' account of the Airport Utility setup process:*
Airport version 7.4.2
IP address 192.168.0.192
router address: 192.168.0.2
Configuring over Airport connection.
- I want AE to join my current network
-.. connect AE to my network using ethernet to extend or create second network
- select device AE will connect to using ethernet - DIR-655 network (displayed w/ airport icon?)
- create an additional network (through ethernet)
AE updates..
- problem 1 of 1 : unsecured wireless network
wpa wpa2
Bridge mode or share a single IP address using DHCP
selected bridge mode
results: AE has green light, airport utility is satisfied but no connection to network is possible. Shared connections are visible, but unable to access
next try:
manual setup
Wireless mode: create wireless network
radio mode: 802.11n only (5 GHz)
channel: auto
wireless security: WPA2 personal
(bridge mode still active)
(this is the exact setup that worked for years before..)
updated…
AE light is green, but no connection to internet or shared connections (though visible)
back to airport utility
manual setup:
internet menu:
connection sharing: share a public IP address
update
--> 2 problems
DHCP Beginning address: 192.168.0.2
DHCP Ending Address: 192.168.0.2
chose 'assist me'
(now one shared connection to Mac Mini becomes active? Had selected it earlier. Able to browse folders, but not share screen)
AE refreshed now with amber light, with reported problems
Problem 1 of 2: Internet Connection
Your Apple Wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network… etc
- changed IP address to match router IP address (?) Utility goes on to next problem
Problem 2 of 2: Conflicting DHCP Range
This Apple wireless device rejected a DHCP address in the same subnet as its internal DHCP server. You should probably switch your Apple wireless device to be in bridge mode. If you still want to be using DHCP and NAT to share a single IP address, you should change your DHCP range.
- maintain selection: share a single IP address using DHCP and NAT (utility forces you to: ignore; skip; or select bridge mode - which doesn't work..)
- chose 'skip' for problem 2
- updated AE..
New problem:
Problem 1 of 1: Double NAT
This Apple wireless device has a private IP address on its Ethernet WAN port. It is connected to a device or network that is using Network Address Translation (NAT) to provide private IP addresses. you should change you Apple wireless device from using DHCP and NAT to bridge mode.
- selected Bridge Mode
updated AE…
"Setup Complete!"
Unable to connect.
** At this point, I am still able to see my shared connections, and while iTunes is open, I can play my shared library that is on my Mac Pro, which connected to the DIR-665 via ethernet, through yet another D-Link router (DIR-615)! I am still connected to the Airport Extreme via wireless, so the system is working, to an extent.*
*So I'm not sure what to do. How can I remedy my IP address issue? Bridge mode doesn't work (as far as I've experienced), so I'm struggling with my DHCP settings..*
*Thanks to anyone who has any suggestions!*

Hi Preston,
I would recommend not starting the numbering scheme for the IP addresses using a '0'. Yes the range is 0-255, but some numbers are reserved, and not generally good practice.
Also, assuming you have reset all factory defaults, start anew and have the modem --> router using NAT for dynamic IP addresses --> (other side of the house) Airport Extreme --> not a NAT configuration, but you need a simple switch. Do not use the NAT capabilities on this one. Maybe, just maybe the computer will work now. This will eliminate your double NAT and also help (hopefully) with the D-Link.
Sorry I cannot help more, I do not own any of the products you talk about, however I have networking experience. Hope it helps.
--Morris

How to configure AnyConnect/ASA/Certificate/MS CA together

Hello
We are looking to apply mobile device management utilizing some third-party cloud solution. Mostly iPad users will connect to our internal network using AnyConnect thru ASA. Third party MDM will be used to control and provision ipads and i need to provide solution for AnyConnect VPN.
Looking for some guidance, docs, examples, white paper that will provide info how to configure the following:
users will connect to ASA VPN using AnyConnect; certificate issued by internal Microsoft CA and unique to each user will be used for authenticate the user. ACS will communicate with Microsoft AD to check if the user is valid AD user. Once authentication is done, user will have access to internal network.
I am struggling to get all those peace of puzzle togehter so i can work on solution.
I would appreciate if someone will give me some ideas how this whole scenario will work.
Thank you.

Anyone from experts out there? I am sure someone heave doen this before.

Configure WRT54G Wireless Router with PUBLIC IP address and use DHCP for internal computers

Hi,I have an Internet online service with 5 public IP addresses. The router and the AP are connected to a switch. I would like to configure a WRT54G wireless router with one of this IP public Address and use DHCP (with private ip address) for the computers that will connect to the AP. As the AP is connected to the switch it is possible that other wired computers that are connected to the same switch can obtain an IP address from the DHCP ?
Thansk in advance

Thanks for your help. Please correct me if Im wrong. After connecte the equipments the way you suggestI setup a static IP address (The public IP) in the WRT54GI enable DHCP in the WRT54G with a range from 10.10.0.100 to 10.10.0.200 (as an example) The gateway is the Public IP address right ? How do I route the 10.10.0.x addresses to the public IP address. Thansk again

How to configure quality process with batch management.

Dear Friends,
we have a scenario,our client receive goods with 101movement type into quality inspection stock.
once stock is passed quality check stock,then we will take into unrestricted stock with 321 movement type.
failed in quality test will be rejected.please give me suggestion how to map the scenario.while i am testing
the process in my sandbox,its asking batch number.its not allowing me to post unrestricted stock with 321
movement type.how to make batch as optional in this scenario?if batch is mainted for the material,how to
configure the process.we are not using QM module.
please suggest me.
Regards,
Varun

In Batch management config in Logistic general, Check for the movement type 101 & 321 whether batch creation has been activated to Manual, Automatic, or no creation. In your case it looks like for mvt 321 batch creation is set to manual & for 101 no creation.
if batch creation is set to manual, enter a manual batch no & proceed.
But to cross verify wheter 101 has generated batch or not please check the stocks in MMBE.
Hope this helps.
Regards
Mithun

How to configure UDDI Server with in EDK with a 4.5WS?

I'm trying to develop a crawler service using EDK5.0.1 with a 4.5ws portal.
To do this job, I have to deploy and coufigure a UDDI Server which is a requirement for services in 4.5ws.
After develping and deploying a crawler service, I created gadget server in the 4.5ws portal, and tried to add remote data source, but the popup window for datasource seems not to be able to find the crawler service and showed 'Empty Gadget Server'.
I think I set up the uddi server with a wrong way, but I don't know what I have to do more to set a uddi server.
Actually, after developing crawler service and sci service, I deployed these with DeployServlet which is a deploy toolkit offered by EDK.
With this deploying result, I modified the uddi.xml file and put that file into c:\program files\Plumtree\ptedk\5.0\devkit\config\java\uddi folder.
Is there any things to set for uddi server?
Can anybody provide me any advise on this?
Any help would be appricated.

The UDDI is used with web services in 4.5x. This is best described as a phone book of URLS for any web services installed in that machine. Those URLS will then point to the individual web services.
In 5.0 the UDDI server is not needed since it is replaced with the "Remote Server" and "Web Services" tabs. HOw to setup a UDDI with TOMCAT
UDDI can be setup to run with TOMCAT and I believe this is the only one provided in the EDK installer in the ptedk\5.0\devkit\java directory
Here's a little TOMCAT information. Web applications are deployed in a folder called "webapp". This case, we have a uddi server installed and it's in a folder called "uddi". So, our file structure for the UDDI server looks like: /webapp - tomcats web application folder /uddi - the uddi application /WEB-INF - standard WEB-INF directory stores java classes, jars and any descriptor files. server-config.wsdd - this is the web service descriptor file for this uddi server - provided by plumtree web.xml - this is the web.xml descriptor file for how the web services in this application will be loaded and run - provided by plumtree /lib - contains the jar files for the uddi server - provided by plumtree The server-config.wsdd file should be the only item that the user needs to modify. Within the file (XML based), there should be the following tag:  <service name="MessageService" provider="java:MSG" style="message"> <parameter name="allowedMethods" value="find_tModel find_business find_binding"/> <parameter name="className" value="com.plumtree.remote.uddi.UDDIServer"/>  <parameter name="baseUrl" value="http://rickc-loaner:81/ntcws/"/>  <parameter name="isDotNet" value="true"/>   <parameter name="crawlerName" value="NT File CWS"/>  <parameter name="authName" value=""/>  <parameter name="documentProviderRpc" value="DocumentProviderSoapPort"/>  <parameter name="containerProviderRpc" value="ContainerProviderSoapPort"/>   <parameter name="sciDataSourceRpc" value="SciSoapPort"/>  <parameter name="sciCrawlRpc" value="SciSoapPort"/>  <parameter name="sciCardRpc" value=""/>   <parameter name="authProvider" value=""/>  <parameter name="syncProvider" value=""/>  <parameter name="authSci" value=""/>  <parameter name="documentProviderDoclit" value="documentprovidersoapbinding.asmx"/>  <parameter name="containerProviderDoclit" value="containerprovidersoapbinding.asmx"/>   <parameter name="sciDataSourceDoclit" value="xuiservice.asmx"/>  <parameter name="sciCrawlDoclit" value="xuiservice.asmx"/>  <parameter name="sciCardDoclit" value="xuiservice.asmx"/> </service> This tag contains the information that will be specific to the user's deployment of the web service (CWS or AWS).First off: <parameter name="baseUrl" value="http://machinename:81/ntcws/"/>
This is the location of the web server that has the target web service installed. THIS CANNOT BE "localhost". This has to be a resolvable machine name or IP address. In 5.0 this is the Remote Web Service settings. Second, you need to set the type of web service.  <parameter name="isDotNet" value="true"/> If your app server hosting the web service is dotnet, you need to set this to "true". This is equivalent to the Document encoding setting in 5.0. .NET supports Document/Literal incoding instead of RPC for Java. Third, name your web services. This is the name that will display in the drop down list in 4.5WS when you decide to create a remote data source.  <parameter name="crawlerName" value="NT File CWS"/>  <parameter name="authName" value=""/> This is the web service name property when you create a new web service in 5.0. Next are the configuration settings for your particular web service:  <parameter name="documentProviderRpc" value="DocumentProviderSoapPort"/>  <parameter name="containerProviderRpc" value="ContainerProviderSoapPort"/>   <parameter name="sciDataSourceRpc" value="SciSoapPort"/>  <parameter name="sciCrawlRpc" value="SciSoapPort"/>  <parameter name="sciCardRpc" value=""/>   <parameter name="authProvider" value=""/>  <parameter name="syncProvider" value=""/>  <parameter name="authSci" value=""/>  <parameter name="documentProviderDoclit" value="documentprovidersoapbinding.asmx"/>  <parameter name="containerProviderDoclit" value="containerprovidersoapbinding.asmx"/>   <parameter name="sciDataSourceDoclit" value="xuiservice.asmx"/>  <parameter name="sciCrawlDoclit" value="xuiservice.asmx"/>  <parameter name="sciCardDoclit" value="xuiservice.asmx"/> These are equivalent to setting the Document provider URL, Container Provider URL, Remote UI URL etc etc that are in 5.0 web services settings. Once you have installed the UDDI server, and started TOMCAT, you should be able to hit the services list at:http://machinewithuddi:8080/uddi/services This will become your Remote Gadget Server URL and you should be good to go!!

How to configure Oracle Discoverer with EBS R12 ?

Dear
I hope, by default Oracle Discoverer is not configured with EBS R 12. How to configure it?
Any hlep, highly appreciated.

Ateeq,
Please refer to the following note, it should be helpful:
Note: 373634.1 - Using Discoverer 10.1.2 with Oracle E-Business Suite Release 12
https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=373634.1

How to configure an ASA with 2 Public IP address.

Similar Messages

Maybe you are looking for