How to configure AP1200 repeater with WPA-EAP

Hi, my network have 4 AP 1240 configured how root AP. These APs use WPA-EAP (MS-CHAPV2) with radius and are working fine.
Now I need install another AP how repeater. Using WPA-EAP don't work. I tested using WPA-PSK and work fine.
Anyone can help me.
Thanks. Tavares

Hi,
You need to point both the root and the non-root towards the ACS server using IP address and port 1812 using eap settings and then specify a eap username and password under the ssid. Please see below partial config from my non-root which is using Cisco LEAP:
ssid XXXX
authentication network-eap eap_methods1
authentication client username XXXXXXXX password XXXXXXXXXX
station-role non-root
radius-server host x.x.x.x auth-port 1812 acct-port 1813 key xxxxxxxxx
radius-server vsa send accounting
Hope this is of some help!
Regards
Mark

Similar Messages

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

Hello, since nobdy else has replied...
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

How to configure bt mail with icloud?

how to configure bt mail with icloud?

iCloud does not handle any mail systems except for its own. BT is not an iCloud mail system, so you can't.

Qosmio F60-L10 - How to configure tv tuner with integrated antenna?

good evening,
i have a notebook toshiba qosmio f60 ,i had read your answer about tv tuner.
my question is : how to configure tv tuner with integrated antenna? thanks

Hi 3171954,
I think Paolo30 is right. Qosmio F60 is equipped with internal DVB-T but in some cases you need an external antenna to pick up the low signal. In most cases only in large citys you dont need an external antenna. If you live on the fringe of the city, normally a cable is needed.
Anyway, do you mean an external antenna or external DVB-T receiver (USB stick)?
Normally Windows media center should recognize the internal DVB-T tuner. Is it listed in device manager? Did you update the driver?

How to configure portal server with the Backend Oracle database

Hi Portal Experts,
we are planning to install Netweaver 04s sp stack 9 full java edition with Oracle 8i on windows platform.
we have the installation docs of portal but we didn't have any idea about how to configure Portal server with the Backend Oracle database at the time of installation or after ost installation of portal.can anyone provide the documentation about this or guide me how to achieve this.
PLZ share ur views---your help would be highly appreciable.
Regds
Phani.

HI
if you r working in Sap enterprise portal use for connection url
jdbc:sap:sqlserver://ilsql01.tlv.sap.corp:1433;DatabaseName=Northwind
ilsql01.tlv.sap.corp:1433 this is your portal url with port number
Northwind is your database name.
for dirver you need to give
com.sap.portals.jdbc.sqlserver.SQLServerDriver
in case if you r working on other than sap say windows along with oracle try to use
Connection URL as jdbc:oracle:<drivertype>:@<database>
Driver name as oracle.jdbc.driver.OracleDriver
ex jdbc:oracle:thick:@localhost:3036:mydb
Oracle implements two types of JDBC drivers:
Thick JDBC drivers built on top of the C-based Net8 client, as well as a Thin (Pure Java) JDBC driver to support downloadable applets. Oracle JDBC drivers are used to create JDBC applications to communicate with Oracle databases.
Oracle extensions to JDBC include the following features:
Data access and manipulation
LOB access and manipulation
Oracle object type mapping
Object reference access and manipulation
Array access and manipulation
Application performance enhancement
*************if the information is helpful to you please reward points************

How to configure IIS webserver with weblogic so that I can invoke servlets without the .wlforward extension

How to configure IIS webserver with weblogic so that I can
invoke servlets without the .wlforward extension
As per the documentation iisforward.dll is registered as a filter and .wlforward
has also been
included as a special file type. However this requires me to key-in ".wlforward"
after my servlet name.
What I want is something like this
http://iis/MyServlet
Please help me find a solution to this
Thanks,
Rishi

I am able to invoke the servlet without the wlforward extension now.
However, now I am required to add /weblogic before the servlet
name otherwise it does not execute the pathtrim property.
I have tried with the pathprepend thing also.
Can we get rid of the /weblogic part also. I just want to execute
my servlet as http://iis/myServlet.
Your help in this regard is greatly appreciated...
Thanks..
"Rishi" <[email protected]> wrote:
>
Thanks for the reply Kumar.
I did follow the instructions as given in the Weblogic documentation
The documentation said to add iisforward.dll as a filter service
and register .wlforward as a special
file type to be handled by iisproxy.dll. For this,
while configuring the IIS server in the Home Directory tab
I added an extension ".wlforward" and the executable as
iisproxy.dll. Is this the way it should have been done...
I also modified the iisproxy.ini file as per the documentation.
I have added the WLForwardPath property and set it to /weblogic.
My server works fine when I give the url as
http://iis/myServlet.wlforward
but it does not work for
http://iis/myServlet and this is the way i'd want it to work.
Please tell me if I am missing something on the configuration part
and if there is something special that needs to be done. I shall
be grateful to you.
Kumar Allamraju <[email protected]> wrote:
http://e-docs.bea.com/wls/docs61/adminguide/isapi.html#101184
Rishi wrote:
How to configure IIS webserver with weblogic so that I can
invoke servlets without the .wlforward extension
As per the documentation iisforward.dll is registered as a filter
and
.wlforward
has also been
included as a special file type. However this requires me to key-in".wlforward"
after my servlet name.
What I want is something like this
http://iis/MyServlet
Please help me find a solution to this
Thanks,
Rishi

How to configure quality process with batch management.

Dear Friends,
we have a scenario,our client receive goods with 101movement type into quality inspection stock.
once stock is passed quality check stock,then we will take into unrestricted stock with 321 movement type.
failed in quality test will be rejected.please give me suggestion how to map the scenario.while i am testing
the process in my sandbox,its asking batch number.its not allowing me to post unrestricted stock with 321
movement type.how to make batch as optional in this scenario?if batch is mainted for the material,how to
configure the process.we are not using QM module.
please suggest me.
Regards,
Varun

In Batch management config in Logistic general, Check for the movement type 101 & 321 whether batch creation has been activated to Manual, Automatic, or no creation. In your case it looks like for mvt 321 batch creation is set to manual & for 101 no creation.
if batch creation is set to manual, enter a manual batch no & proceed.
But to cross verify wheter 101 has generated batch or not please check the stocks in MMBE.
Hope this helps.
Regards
Mithun

How to configure UDDI Server with in EDK with a 4.5WS?

I'm trying to develop a crawler service using EDK5.0.1 with a 4.5ws portal.
To do this job, I have to deploy and coufigure a UDDI Server which is a requirement for services in 4.5ws.
After develping and deploying a crawler service, I created gadget server in the 4.5ws portal, and tried to add remote data source, but the popup window for datasource seems not to be able to find the crawler service and showed 'Empty Gadget Server'.
I think I set up the uddi server with a wrong way, but I don't know what I have to do more to set a uddi server.
Actually, after developing crawler service and sci service, I deployed these with DeployServlet which is a deploy toolkit offered by EDK.
With this deploying result, I modified the uddi.xml file and put that file into c:\program files\Plumtree\ptedk\5.0\devkit\config\java\uddi folder.
Is there any things to set for uddi server?
Can anybody provide me any advise on this?
Any help would be appricated.

The UDDI is used with web services in 4.5x. This is best described as a phone book of URLS for any web services installed in that machine. Those URLS will then point to the individual web services.
In 5.0 the UDDI server is not needed since it is replaced with the "Remote Server" and "Web Services" tabs. HOw to setup a UDDI with TOMCAT
UDDI can be setup to run with TOMCAT and I believe this is the only one provided in the EDK installer in the ptedk\5.0\devkit\java directory
Here's a little TOMCAT information. Web applications are deployed in a folder called "webapp". This case, we have a uddi server installed and it's in a folder called "uddi". So, our file structure for the UDDI server looks like: /webapp - tomcats web application folder /uddi - the uddi application /WEB-INF - standard WEB-INF directory stores java classes, jars and any descriptor files. server-config.wsdd - this is the web service descriptor file for this uddi server - provided by plumtree web.xml - this is the web.xml descriptor file for how the web services in this application will be loaded and run - provided by plumtree /lib - contains the jar files for the uddi server - provided by plumtree The server-config.wsdd file should be the only item that the user needs to modify. Within the file (XML based), there should be the following tag:  <service name="MessageService" provider="java:MSG" style="message"> <parameter name="allowedMethods" value="find_tModel find_business find_binding"/> <parameter name="className" value="com.plumtree.remote.uddi.UDDIServer"/>  <parameter name="baseUrl" value="http://rickc-loaner:81/ntcws/"/>  <parameter name="isDotNet" value="true"/>   <parameter name="crawlerName" value="NT File CWS"/>  <parameter name="authName" value=""/>  <parameter name="documentProviderRpc" value="DocumentProviderSoapPort"/>  <parameter name="containerProviderRpc" value="ContainerProviderSoapPort"/>   <parameter name="sciDataSourceRpc" value="SciSoapPort"/>  <parameter name="sciCrawlRpc" value="SciSoapPort"/>  <parameter name="sciCardRpc" value=""/>   <parameter name="authProvider" value=""/>  <parameter name="syncProvider" value=""/>  <parameter name="authSci" value=""/>  <parameter name="documentProviderDoclit" value="documentprovidersoapbinding.asmx"/>  <parameter name="containerProviderDoclit" value="containerprovidersoapbinding.asmx"/>   <parameter name="sciDataSourceDoclit" value="xuiservice.asmx"/>  <parameter name="sciCrawlDoclit" value="xuiservice.asmx"/>  <parameter name="sciCardDoclit" value="xuiservice.asmx"/> </service> This tag contains the information that will be specific to the user's deployment of the web service (CWS or AWS).First off: <parameter name="baseUrl" value="http://machinename:81/ntcws/"/>
This is the location of the web server that has the target web service installed. THIS CANNOT BE "localhost". This has to be a resolvable machine name or IP address. In 5.0 this is the Remote Web Service settings. Second, you need to set the type of web service.  <parameter name="isDotNet" value="true"/> If your app server hosting the web service is dotnet, you need to set this to "true". This is equivalent to the Document encoding setting in 5.0. .NET supports Document/Literal incoding instead of RPC for Java. Third, name your web services. This is the name that will display in the drop down list in 4.5WS when you decide to create a remote data source.  <parameter name="crawlerName" value="NT File CWS"/>  <parameter name="authName" value=""/> This is the web service name property when you create a new web service in 5.0. Next are the configuration settings for your particular web service:  <parameter name="documentProviderRpc" value="DocumentProviderSoapPort"/>  <parameter name="containerProviderRpc" value="ContainerProviderSoapPort"/>   <parameter name="sciDataSourceRpc" value="SciSoapPort"/>  <parameter name="sciCrawlRpc" value="SciSoapPort"/>  <parameter name="sciCardRpc" value=""/>   <parameter name="authProvider" value=""/>  <parameter name="syncProvider" value=""/>  <parameter name="authSci" value=""/>  <parameter name="documentProviderDoclit" value="documentprovidersoapbinding.asmx"/>  <parameter name="containerProviderDoclit" value="containerprovidersoapbinding.asmx"/>   <parameter name="sciDataSourceDoclit" value="xuiservice.asmx"/>  <parameter name="sciCrawlDoclit" value="xuiservice.asmx"/>  <parameter name="sciCardDoclit" value="xuiservice.asmx"/> These are equivalent to setting the Document provider URL, Container Provider URL, Remote UI URL etc etc that are in 5.0 web services settings. Once you have installed the UDDI server, and started TOMCAT, you should be able to hit the services list at:http://machinewithuddi:8080/uddi/services This will become your Remote Gadget Server URL and you should be good to go!!

How to configure Oracle Discoverer with EBS R12 ?

Dear
I hope, by default Oracle Discoverer is not configured with EBS R 12. How to configure it?
Any hlep, highly appreciated.

Ateeq,
Please refer to the following note, it should be helpful:
Note: 373634.1 - Using Discoverer 10.1.2 with Oracle E-Business Suite Release 12
https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=373634.1

How to configure the SSL with SharePoint Site

my site is running on http.
When we create the new website it will ask about "Use Secure Sockets Layer (SSL): "
i have select the no and develop a site.
now i want to move it on httpshowever i want to configure this site with SSL certificate.. how can i move it to https?
any one help me how can i acess my site from https:// URL.
i have bought the SSL certificate.
waiting.........
its urgent.

I am also having an issue with adding and SSL cert to an existing site. I am also using a hostname vs the server name for the URL. Here is what I have done so far:
- Local MS DNS Entry (spsite.abccorp.com) point to the IP address of the SP server.
- ensured the port 80 and 443 boxes are filled in in IIS for the "Sharepoint - 80" site.
- Added Certificate to that IIS site, but did not make SSL required (so I could try both http and https without it barking).
- Under the Alternate Access Mapping Section of SP, I changed the URL from http://spsite.abccorp.com to https://spsite.abccorp.com for the "Sharepoint - 80" Collection. I even tried just added the https url to the "Custom" area vs the "Default"
After I have done all this, I get "Page Can Not Be Displayed" when going to the HTTPS site but works fine for the HTTP.
Any suggestions?

How to configure oracle 10g with clients

Hello sir i am a database user.
I want to install an oracle 10g (Client server architecture)
As i have a licenced Oracle 10g CD Pack.
Pls help me how to install Oracle & how to configure its clients.
As i have a server(running server 2003 ) in it and corresponding clients.
Thanks
Edited by: user10439074 on Oct 30, 2008 4:03 AM

Read the documentation (I have given following links assuming you are running a 32 bit architecture)
Server installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14316%2Ftoc.htm&remark=portal+%28Books%29
Client installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14312%2Ftoc.htm&remark=portal+%28Books%29
You can find the required books (if not using 32 bit architecture) from
http://www.oracle.com/pls/db102/portal.portal_db?selected=3

How to configure home network with Airport Extreme + D-Link DIR-665

*hello everyone,*
*I had these two working fine together until the D-Link took a dump the other day. No explanation. Just stopped working until I reconfigured everything.*
*Which then led to my Airport Extreme being unable to connect to the network at all, much less the internet...*
*My home network is set up like this:*
*Optimum Cable*
*Motorola Surfboard modem --> D-Link DIR-655 (via ethernet)*
*- Provides wifi and ethernet connections on one side of my house*
*DIR-655 --> Airport Extreme (via ethernet run to other side of house)*
*- Provides wifi and ethernet connections on the other side of my house*
*My MBP won't connect to anything other than my AE running N, so I have that set up primarily for my MBP over wifi, while feeding an ethernet connection to a Netgear router running B/G, for my iPhone and other devices.*
**So here are the relative details:**
*I decided to start fresh and do a factory default configuration with my Airport Extreme. My working system from earlier was essentially it's own wifi network, but the airport utility 'insists' that I need to run my AE in bridge mode. I've tried that, but I can't get online. I can see my shared connections, so something's getting through, but I cannot connect to them, in addition to being unable to get online.*
*I'm not really sure how to best illustrate this problem, so I've ran through the process again and jotted down a few notes. Excuse the rambling nature of my narrative, this is a 'blow by blow' account of the Airport Utility setup process:*
Airport version 7.4.2
IP address 192.168.0.192
router address: 192.168.0.2
Configuring over Airport connection.
- I want AE to join my current network
-.. connect AE to my network using ethernet to extend or create second network
- select device AE will connect to using ethernet - DIR-655 network (displayed w/ airport icon?)
- create an additional network (through ethernet)
AE updates..
- problem 1 of 1 : unsecured wireless network
wpa wpa2
Bridge mode or share a single IP address using DHCP
selected bridge mode
results: AE has green light, airport utility is satisfied but no connection to network is possible. Shared connections are visible, but unable to access
next try:
manual setup
Wireless mode: create wireless network
radio mode: 802.11n only (5 GHz)
channel: auto
wireless security: WPA2 personal
(bridge mode still active)
(this is the exact setup that worked for years before..)
updated…
AE light is green, but no connection to internet or shared connections (though visible)
back to airport utility
manual setup:
internet menu:
connection sharing: share a public IP address
update
--> 2 problems
DHCP Beginning address: 192.168.0.2
DHCP Ending Address: 192.168.0.2
chose 'assist me'
(now one shared connection to Mac Mini becomes active? Had selected it earlier. Able to browse folders, but not share screen)
AE refreshed now with amber light, with reported problems
Problem 1 of 2: Internet Connection
Your Apple Wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network… etc
- changed IP address to match router IP address (?) Utility goes on to next problem
Problem 2 of 2: Conflicting DHCP Range
This Apple wireless device rejected a DHCP address in the same subnet as its internal DHCP server. You should probably switch your Apple wireless device to be in bridge mode. If you still want to be using DHCP and NAT to share a single IP address, you should change your DHCP range.
- maintain selection: share a single IP address using DHCP and NAT (utility forces you to: ignore; skip; or select bridge mode - which doesn't work..)
- chose 'skip' for problem 2
- updated AE..
New problem:
Problem 1 of 1: Double NAT
This Apple wireless device has a private IP address on its Ethernet WAN port. It is connected to a device or network that is using Network Address Translation (NAT) to provide private IP addresses. you should change you Apple wireless device from using DHCP and NAT to bridge mode.
- selected Bridge Mode
updated AE…
"Setup Complete!"
Unable to connect.
** At this point, I am still able to see my shared connections, and while iTunes is open, I can play my shared library that is on my Mac Pro, which connected to the DIR-665 via ethernet, through yet another D-Link router (DIR-615)! I am still connected to the Airport Extreme via wireless, so the system is working, to an extent.*
*So I'm not sure what to do. How can I remedy my IP address issue? Bridge mode doesn't work (as far as I've experienced), so I'm struggling with my DHCP settings..*
*Thanks to anyone who has any suggestions!*

Hi Preston,
I would recommend not starting the numbering scheme for the IP addresses using a '0'. Yes the range is 0-255, but some numbers are reserved, and not generally good practice.
Also, assuming you have reset all factory defaults, start anew and have the modem --> router using NAT for dynamic IP addresses --> (other side of the house) Airport Extreme --> not a NAT configuration, but you need a simple switch. Do not use the NAT capabilities on this one. Maybe, just maybe the computer will work now. This will eliminate your double NAT and also help (hopefully) with the D-Link.
Sorry I cannot help more, I do not own any of the products you talk about, however I have networking experience. Hope it helps.
--Morris

How to configure SharePoint HNSC with a reverse proxy server so that HNSC Share Point URLs are not exposed to end users.

Could you please let me know how SharePoint HNSC can be configured with a reverse proxy server so that HNSC Share Point URLs are not exposed to end users.
In normal path based site collections/web applications, reverse proxy configuration can be done using alternate access mappings with Public URL = "proxy URL", internal = "HNSC Share Point URL" so that share point sends response back
to Public URL = "proxy URL".
In Host Named Site Collections, alternate access mappings are not supported. Each HNSC is designed to have only one URL in each zone. Zone is one of the five zones(Default,Intranet,Internet,Custom,Extranet) with each of which only one alternate
URL is associated. This is what we are able to get using power shell command "Set-SPSiteUrl", but this will not help us to get the response back to proxy URL after a request sent to share point because we could not find any mechanism in share
point HNSC to respond to a different URL(proxy URL). Consequently, Share Point URLs are exposed to external users.
Below share point article in MSDN blog is symmetrical to what we are observing with Share Point 2013 and Proxy Server. It mentions that internal HNSC URLs can’t be hidden using any proxy server. If hiding the internal Share Point URLS is a requirement,
it suggests to use a web application instead of host named site collections.
Though I’m also observing the same behavior with Share Point 2013 HNSC, Could you please confirm my understanding is correct.
http://blogs.msdn.com/b/kaevans/archive/2012/03/27/what-every-sharepoint-admin-needs-to-know-about-host-named-site-collections.aspx
Excerpt from above article-
"Host Named Site Collections Only Use One Host Name
Continuing on the discussion on AAMs and host named site collections, you cannot use multiple host names to address a site collection in SharePoint 2010. Because host-named site collections have a single URL, they do not support alternate access mappings and
are always considered to be in the Default zone. This is important if you are using a reverse proxy to provide access to external users. Products like Unified Access Gateway 2010 allow external users to authenticate to your gateway and access a site
as http://uag.sharepoint.com and forward the call to http://portal.sharepoint.com. Remember that URL rewriting is not permitted. Further, a site collection can only respond to one host name. This means if you are using a reverse proxy, it must forward the
calls to the same URL. If your networking team has a policy against exposing internal URLs externally, you must instead use web applications and extend the web application using an alternate access mapping."<u5:p></u5:p>

Hi Satish,
You are right that only one URL is allowed for each zone of the host-name site collections in both SharePoint 2010 and SharePoint 2013.
It is by design that each host-name site collection only support one URL for each zone.
The article below is about RTM version of SharePoint, and it is the same for SharePoint 2013 with the latest CU.
https://support.microsoft.com/en-us/kb/2826457
So to make the URL of HNSC not exposed to external users is not supported, you need to use path-based sites instead.
Best regards.
Thanks
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

How to configure discoverer reports with apps

Hi,
i developed a report in discoverer desktop.now i want to link or run the report in apps.
how do i configure this ...
can u help me out ..
regds,
kumar

hi ,
i gone through that note its very helpful to me ..
but i have a doubt .the discoverer reports are opening with Discoverer viewer 4i.how its automatically taking the viewer to open..
whether viewer is a tool(like admin&desktop or ???) . by default its available in application or whether we have to install or apply any patch or ...
and also i tried to open existing(seeded) reports in application through disk desktop its giving the message subtitute item ....
should i replace the existing item (in created workbook) with the new one (which we need)....
pl u clarify me
regards,
kumar

How to configure an ASA with 2 Public IP address.

Hi, I have to configure a router ASA 5505 with 2 Publics IP, our ISP give us a 3 Public IP, and actually our configuration is like this:
interface Vlan1
nameif inside
security-level 100
ip address 192.168.x.x 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 200.91.x.x 255.255.255.248
The problem is: If I create a new Vlan, the interface overlaps.
How can I solve that problem??
Thanks for your answers!!!

Answered in duplicate post:
https://supportforums.cisco.com/discussion/12150111/how-configure-asa-2-public-ip-address

How to configure AP1200 repeater with WPA-EAP

Similar Messages

Maybe you are looking for