How to configure broadcast ip permanently

hi
I have facing problem regarding configuration of broadcast IP
to resolve this ether i have to use ifconfig command for every restart or manually enter ip,netmask & broadcast ip in \etc\hostname.hme0 file in this case my default gateway will also change then i have to use route add command to solve it, again route add also for current session only
my configuration
/etc/inet/hosts 10.205.42.2
/etc/inet/ipnodes 10.205.42.2
/etc/inet/netmasks 255.255.255.0
/etc/inet/defaultrouter 10.205.42.1
In this configuration output is
IP 10.205.42.2 netmask 255.255.255.0 broadcast 10.205.42.255 default gateway 10.205.42.1
Hear i want broadcast IP 10.255.255.255
When i change /etc/hostname.hme0 with
10.205.42.2 newmask 255.255.255.0 broadcast 10.255.255.255
In this case my output is
IP 10.205.42.2 netmask 255.255.255.0 broadcast 10.255.255.255 default gateway 127.0.0.1
Hear i want default gateway 10.205.42.1
plz help to configar this output permanently
IP 10.205.42.2 netmask 255.255.255.0 broadcast 10.255.255.255 default gateway 10.205.42.1

Actually in my organisation vlan is configured with 10.205.XX.XXX 255.255.255.0 if i use 10.205.42.255 broadcast ip, i only communicate with 10.205.42.xxx network. i need to communicate with 10.205.xx.xxx network.

Similar Messages

How to configure Broadcast messaging for IC Webclient profile

Dear all,
How to configure Broadcast messaging for IC Webclient profile. what are the prerequisites for it?
We are not using EP interface for IC Webclient, then where can I find broadcast messaging URL in SAP CRM system.
I have checked for the relevant BSP application, but could not find.
Please help me to configure the scenario successfully, your help will be highly appreciated.
Best regards,
Raghu ram

Hi raghu
In CRM Broad cast messaging application is CRM _BM,
Go to easy access u2013 go to favourites u2013 select add other objects - select BSP Applications- then select CRM_BM Application.
Select that BSP application and test it u2026
`
Regards,
Narsimha

How to configure Broadcasting server in SAP?

Hi,
We are trying to use pre caluculation using broadcasting for queries, for this broadcasting server needs to be configured in the system...
We are using SAP-BI 7.0, Can anybody let us know the step by step solution to configure Broadcasting server
rgds,
KN RAO

Hi,
This links gives you a good idea on what broadcasting exactly is:
http://help.sap.com/saphelp_nw04s/helpdata/en/a5/359840dfa5a160e10000000a1550b0/frameset.htm
Please refer to the link below to hava a general idea on how broadcasting must be configured,you will find information specific to collaboration:
http://help.sap.com/saphelp_nw04s/helpdata/en/84/30984076b84063e10000000a1550b0/frameset.htm
Also check :
How to install and configure a boradcasting server ?
-Vikram

How to configure broadcasting

hi all,
can any one please tell me the steps to be followed for configuring and enabling broadcasting in collaboration
Regards,
jeyasingh Samuel

Hi,
This links gives you a good idea on what broadcasting exactly is:
http://help.sap.com/saphelp_nw04s/helpdata/en/a5/359840dfa5a160e10000000a1550b0/frameset.htm
Please refer to the link below to hava a general idea on how broadcasting must be configured,you will find information specific to collaboration:
http://help.sap.com/saphelp_nw04s/helpdata/en/84/30984076b84063e10000000a1550b0/frameset.htm
This is a sample scenario,<i>Ad-hoc Distribution of the Sales Report into Collaboration Rooms</i> :
http://help.sap.com/saphelp_nw04s/helpdata/en/1c/253741b90df323e10000000a155106/frameset.htm
Regards,
Harish
(Please awrd points for helpful answers)

How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module

hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
                                                  ^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2921/K9          FGL1618119E
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            None          None           None
data          None          None           None
Configuration register is 0x2102
R2921-8CPITR-1#

Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end

Connecting two WRT54G wireless routers - how to configure

Hi All,
I have two WRT54G wireless routers. One is currently providing wireless access for several users at a local law firm. I need to connect a second wireless router for a user who works for another company in the same office. The second wireless router is basically going to be used for Internet access. The Office Manager at the law office does not want the user from the other company using their wireless router directly, BUT they will allow me to hook up the second wireless router for Internet access. I realize this doesn't really make sense in terms of security, but this is the scenario I must abide to. So I am wondering how to configure the second router. I am thinking that I connect a CAT5 from one port on the first router to the Internet port on the second router. I am also guessing that I need to assign the the second router a static IP with a different subnet such as 192.168.2.1. I am not sure if the first router still has the default 192.168.1.1. If the first router does use 192.168.1.1 would I need to change the IP on the second one to one on another subnet? Thanks.

You will need a setup like this:
Modem --- new WRT54G ---- existing WRT54G
192.168.2.1 192.168.1.1 ( "Local IP address" )
Modem connects to Internet port of new WRT54G.
LAN port of new WRT54G connects to Internet port on existing WRT54G.
SSID: different on each router (do not use "linksys" )
SSID broadcast: enabled on both routers
encryption: recommend WPA2, or at least WPA (can be same or different on the two routers).
passwords: different on each router.
channel: try to stay at least 5 channels apart. Usually channel 1, 6, and 11 work best, but any two different channels can be used.
Any "port forwarding" used by existing WRT54G must also be done on new WRT54G.
Both routers need a real login password (not "admin" )
New WRT54G will need "Intenet connection type" set to whatever is currently on existing WRT54G. Internet connection type for existing WRT54G will need to be set to DHCP.
Message Edited by toomanydonuts on 01-15-2008 01:54 AM

How to configure Solaris 10 on a dell laptop to connect to internet

Hi,
I am student and have installed Solaris 10 on my Dell laptop using SUN's Virtual box. I also have Opensolaris on my laptop that is able to connect to internet using any available wireless because of its auto settings. Can some one please guide me with the steps or tutorial to configure Solaris 10 to connect to internet either by LAN or wireless(preferable)
Some information about my Laptop:
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::548:a39d:e943:4144%12
IPv4 Address. . . . . . . . . . . : 192.168.100.198
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.100.1
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Ethernet adapter VirtualBox Host-Only Network:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::4112:b7fa:5de1:2f6e%15
IPv4 Address. . . . . . . . . . . : 192.168.56.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 7:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 11:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 14:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask ff000000
ether 8:0:27:60:84:8d
#netstat -nrv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd
224.0.0.0 240.0.0.0 127.0.0.1 lo0 8232* 0 1 U 0 0
127.0.0.1 255.255.255.255 127.0.0.1 lo0 8232* 0 33 UH 976 0
Please let me know if you need any other information

For a start I would give my interface an inet number:
ifconfig <interface> inet <ip_address>
ifconfig e1000g0 inet 192.168.100.198
...further than that I would need to study.
Also see " How to configure internet Solaris 10" thread .
http://forums.sun.com/thread.jspa?threadID=5093731&tstart=0
Edited by: plasmichive on Nov 10, 2009 10:25 AM

How to configure connectivity between two vm linux hosts

Hello All,
i have installed vm workstation with two RHEL4 linux installation.
Node 1:RHEL4
Node 2:RHEL4
i have configured 2 ethernet cards am able to ping in a host but not each other.
i have tried to ping from Node 1 to Node 2 am getting icmp_seq=0 Destination Host Unreachable .....
kindly suggest how to configure connectivity between two host permanently.please explain with example if possible. or suggest any link.
thanks,
Mike.

1003614 wrote:
thanks for quick reply ....Oracle vm workstation 4.2 am using.
... then your post is now moved to the appropriate forum space for your question (Oracle VM for x86).

How to configure oracle listener profile for multiple oracle database

Hi,
I am going to install solution manager system in the same server of ERP EHP4 on Windows. Both DB are oracle.
I'd like to know how to configure listener in this kind of envirnmonent.
a. use two listener and different ports
b. use same listener but different ports
c. use same listener and same port
Which is the correct mothed?
And, after installation, there seem three set of profiles of listten, one for ERP, one for SLM, and the other for OS?(%windir%system32), which one is functional?
Please advise.
Thanks a lot.
Regards,
Alex

Hi,
standard installation is creating new configs for listener for each instance.
I would recommend to use one listener per each instance.
YOU CAN NOT HAVE one port number for two differnet systems!
If you want to use one listener than you must adapt tnsnames.ora, listener.ora and ensure that both systems will use different port numbers.
For example PORT= 15<system number>
Peter

How to configure one TREX host with multiple index servers ?

Hi All,
Does anyone know how to configure TREX on the one host,
with multiple index servers ?
Reason for this is to make better use of resources available on the host server(4 Gig, 4 Processor, Windows2003), to improve the search performance of
our KM content for portal users.
I am using TREX 7 and have not been able to do this,
despite reading the Single and Distributed install
documentation.
Any help would be appreciated.
Regards,
Andres

Hi Andres,
To make use of the RAM a Server provides you have to run two indexserver processes (each can then consume 2 GB);
Proceed like this:
1. Go to TREXdeamon.ini; check if section [indexserver2] is there (it is already provided, but not active in standard installation)
2. In TREXdeamon.ini go to
[daemon]
references sections below
programs=nameserver,preprocessor1,indexserver1,queueserver,alertserver
and add indexserver2 here. Restart TREX; second porcess is then started; can be checked in TREX monitor in Portal as well
3. To distribute existing indexes to the new process, start TREXadmintool and go to Index: Landscape
Go to the last two columns and move the indexes (move master here/secondary mouse click)
If you don't distribute the indexes the new index server process will be regarded when an new index is created.
Hope this helps!
cheers
Bettina

How to configure request manager service for multiple website in one web application

I have set up sp 2013 as below:
web application : wa1
site collection : sc1
sp site: site1, site2
I used 2 WFE, 1 APP, how can I use request manager service to control site1 to wfe1, site2 to wfe2?
Awen

That's not what i'd describe as load balancing.
A better description would be load-isolation. In your description then if the load on site1 was large (and growing) but site2 was quiet then site1 would struggle and eventually become unable to handle the number of users but site2 would still be ok. That's
fine from a QOS point of view but it's not the norm for load balancing. It would work in simple scenarios but the out of the box load balancing tools are much better suited than that sort of approach.
This article shows how to configure the RMS and may help show how your request is difficult to configure:
http://www.harbar.net/articles/sp2013rm2.aspx

How to configure 3 different members under a single Month column

Hi SAP Gurus,
My client requirement is to show the report in following format, where under a Month column 3 different columns having
1) Quantity (Number of unit ) of a product,
2) its rate (Amount per unit), and
3) Total (amount)    will appear in a single report.
   I have Month as a Time Dim, while Qty, Rate and Total are members of account dim.
Que: How to configure such scenario in a single report?
Jan.2011
Product Category:            Qty (Input)   Rate (Input)   Total (Output)
Product 1
Product 2
Product 3
Product 4
Group1
     Where: Total = Qty X Rate
Thanks and Regards,
SouarbhD

Hi,
Use an EVDRE to create your input schedule. You need to have one row with products and 2 columns with time and account. Choose the memberset options as per the requirement. For the accounts, is total calculated with a dimension formula? If yes, then you just need to enter the values for quantity and rate and send the data. The total will be calculated by the system and will be displayed automatically.
Hope this helps.

How to configure an Alert message if communicationChannel(JMS) stops

All,
Is there a way how to configure an alert when the communication channel stops.
<b>Scenario:</b>
In the path Runtime workbench->Component Monitoring->Adapter Engine->Communication Channel monitoring, if we see that a communication channel has stopped(RED traffic light as Status), then can we trigger an alert notification for same.
Currently we have alrerts configured for any message/s failure in the JMS Adapter Framework. So can we trigger simmilar alerts when a comm channel stops(for whatever reason).
Thanks in advance
RK

Hi Sreeram,
Thanks for the quick reply.
We have a scenario where we activate individual channels at a given time. So in this case, Adapter will always be in RED as all queues are never running in our scenario.
So we need an ALERT to be triggered for individual comm channels. Is theer any way that you can think of ?
Thanks and regards
RK

How to configure multiple IP addresses on one NIC?

Hi,
I just installed a OVM Server in version 3.2.1 and the according VMManager. Now i wanted to try to configure the Server/Server Pool. Now i come across a problem, which was already a big problem in OVM 2 while configuring the Networks.
All our OVM Servers have three NICs in them. One is for VMs and Management, the others are for connection to our SAN (Dell PowerVault MD 3220i). My problem is, that due to the network setup, the two NICs for storage need two IP addresses in two different networks each. This shouldn't be a problem, because usually in linux all you have to do is configure something like eth1:1. I remember having huge trouble configuring it in our OVM 2 cluster up to the point where I had to write a shell script to configure the second IP.
Anyways, I have configured two of the storage networks on eth1 and eth2 of the VM Server. Now i cannot configure any more IP addresses, because eth1 and eth2 are not available anymore for configuration in a third network. I really hoped that it would be possible in OVM 3 to configure multiple IP addresses. And probably it is only my lack of knowledge of how to configure it.
So any advice is well appreciated.
Thanks!
Regards,
Marek Hubatka

You should be able to do this by using "VLAN Groups".
http://docs.oracle.com/cd/E35328_01/E35332/E35332.pdf
Check out the VLAN groups section. You must great the VLAN groups before you can assign them to interfaces.

IAS 10.1.2-how to configure different oc4j listen to different virtualhost?

Hi
I have requirement,
we have oracle portal based web site that can be used by outside users over the internet.
And then we have are deploying few new apps/webservices/ear files on a oc4j called core_ws. These web services should not be accessed outside.
I have created a virtaul host in apache on a different port(7799) which was not exposed to public world.
But, how to configure core_ws to inform Apache to listen on only port 7799 but not on port 80?
I tried a diffent route to attack the problem(as mentioned below) which managmenet did not like:
created location directive, worked in dev but not in production as there ISA sitting front of apache.
We could apply filter on the URLs of these web services in ISA but my director did not like the idea as each time there is additional web service we have mess with it.
So, he prefers running these web services on a different port that will not have access to public.
Appreciate your help if have acheived the same earlier.

By your description, it sounds like you want to do what is in this My Oracle Support document:
How To Create Virtual Host Specific OC4J Applications (Doc ID 389819.1)
https://support.oracle.com/CSP/main/article?cmd=show&type=NOT&id=389819.1
(requires login)
You said you were using 10.1.2, so that will work, its a method of creating separate virtualhosts and using rewrites to direct to error pages if an incorrect request is made. For 10.1.3, but there is a dynamic method which is a better approach.
...Ken

How to configure broadcast ip permanently

Similar Messages

Maybe you are looking for