How to configure DHCP in Hyper-V

Hi
Recently I have created 2 Hyper V nodes in Windows 8. One is windows server 2012 and second one is windows 8.
My Question is :
How can I configure DHCP in server 2012 that can provide IP address to windows 8 . I have made win server 2012 a domain controller and also installed DHCP role.
PLZ HELP!!!!!!!!

As Ryan has said in his reply, there's nothing different to setting up DHCP in a Hyper-V VM as there is on a physical host.
If you've not done this in 2012 (R2) before then you may be missing the notification in Server Manager after the install notifying you that there is post installation tasks for DHCP to complete.
I suggest you read the information at the link Alexey posted as there information to take you through step by step.
The link again:
http://blogs.technet.com/b/keithmayer/archive/2012/11/26/configuring-dhcp-in-windows-server-2012-early-experts-challenge-exam-70-410.aspx
Direct step links:
Authorize a DHCP Server
Create and configure scopes
Configure a DHCP reservation
Configure DHCP options
Configure a Client and Server for PXE Boot (BOOTP)
Configure IPv4 DHCP Relay Agent
Configure IPv6 DHCP Relay Agent
Regards,
Steve
My System Center Blog

Similar Messages

How to configure dhcp client identifier

Hi Everybody,
The DHCP client ID is an id that is unique for DHCP clients at least in the same subnet. Usually the client uses MAC-address as Client-Identifier in the DHCPDISCOVER message. The Client-Identifier may be different other than MAC-Address, For example a FQDN name, as per the RFC 2132 Ref, (code 61).+_
Usaually, we use the following to bind the ip address based on MAC-address
pntadm -r SUNWfiles -p /var/dhcp -A 10.42.32.86 -i '0:3:ba:a5:a9:93' -a 10.42.32.80
At server side, I am using the following for specifying the FQDN name.
pntadm -r SUNWfiles -p /var/dhcp -A 10.42.32.86 -i 'one.atr.com' -a 10.42.32.80
and at client side, I am inserting the following entry in the /etc/default/dhcpagent file
CLIENT_ID='one.atr.com'
But this is not working. What I am doing wrong.
+1. At the server side, then how to assign the ip addresses to the clients , if the Client-Identifier is FQDN name in the DHCPDISCOVER message other than MAC-Address.+
+2. How to configure the client-identifier as FQDN name at client side.+
Please help me,
Thanks Inadvance,
Mummaneni.

Sandman,
Here is an example of a router acting as a DHCP server. Please remember that you have to exclude IP addresses that you don't want to lease out.
ip dhcp pool example
import all
network 192.168.1.0 255.255.255.0
dns-server 1.2.3.4
default-router 192.168.1.1
ip dhcp excluded-address 192.168.1.1 192.168.1.149
ip dhcp excluded-address 192.168.1.200 192.168.1.254
HTH,
Mark

How to Configure DHCP/NAT in Time Capsule

Assuming I can get my Comcast Cable model to act as a bridge, I see advice for setting up my Time Capsule as a DHCP/NAT.
On the Comcast Cable modem:
WAN IP address = 174.13.188.121. <- fake IP
WAN IP gateway = 174.13.188.122.
WAN subnet mask = 174.13.188.122.
LAN IP address = 10.1.10.1.
LAN subnet mask = 255.255.255.0.
I'd like to use 10.1.10.11 for Time Capsule, 10.1.10.13 for Mac Mini Server, 10.1.10.17 for iMac#1 and 10.1.10.19 for iMac#2.
But nooooooo. The AirPort Utility offers only the following DHCP Ranges:
10.0.1.3 - 10.0.1.200, or
176.16.1.3 - 176.16.1.200, or
192.168.1.3 - 192.168.1.200
There's a checkbox for "Enable NAT Port Mapping Protocol," but the documentation on it is poor. There's also a checkbox for "Enable default host at: 10.0.1.253, or 176.16.1.253 or 192.168.1.253," but its documentation is equally poor. Apparently Apple didn't see the need to explain how these things work.
If I use a LAN IP of 10.0.0.1 for the Comcast Cable Modem, then use AirPort Utility to set a DHCP Range of 10.0.0.3 to 10.0.0.200 I receive a warning message that "The DHCP range you have entered conflicts with the WAN IP address of your base station."
I don't see the conflict -- what is wrong? Better yet, how do use AirPort Utility to set up Time Capsule?

Thank you for your response, but I remain completely overwhelmed by this mess. What should be something simple has become an enormous task.
Internet
^
Cable Modem WAN IP: 174.13.188.121 (fake IP address)
   Subnet Mask WAN: 255.255.255.252
Cable Modem LAN IP: 192.168.0.1
    Subnet Mask LAN: 255.255.255.0
I'd like all requests to my public static IP 174.13.188.121 to be served up from my Mac Mini Server with private static IP 192.168.0.19.
   Time Capsule IP: 192.168.0.11
Mac Mini Server IP: 192.168.0.19 running Server.app
iMac #1 Client IP: 192.168.0.17
iMac #2 Client IP: 192.168.0.13
I want the Server.app to serve the public. The above is what I have configured now. Some behavior is odd. For example, I can access the internet from the iMac clients but not the Mac Mini Server. I don't know why.
In other words, how do I string together my Comcast Cable Modem, Time Capsule, Mac Mini Server, iMac#1 and iMac#2 into a useful LAN that can browse the Internet and provide FTP and Web service?
I would think this is a common setup with several sample setups available on the web. No such luck.

How to configure Dhcp relay agent

How I can to configure the wrt54g like a dhcp relay agent? please i need help, tell me

A DHCP relay agent is any host that forwards DHCP packets between clients and servers. Relay agents are used to forward requests and replies between clients and servers when they are not on the same physical subnet. Relay agent forwarding is distinct from the normal forwarding of an IP router, where IP datagrams are switched between networks somewhat transparently. By contrast, relay agents receive DHCP messages and then generate a new DHCP message to send out on another interface. The relay agent sets the gateway address (giaddr field of the DHCP packet) and, if configured, adds the relay agent information option in the packet and forwards it to the DHCP server. The reply from the server is forwarded back to the client after removing option .

How to configure DHCP on linux jumpstart for solaris installation

I have configured jumpstart on linux and able to install solaris on SUN sparcs
using rarp and bootparams files.now im trying to use linux DHCP for solaris clients. I have the done the DHCP setup on linux using this doc http://www.sun.com/bigadmin/content/submitted/setup_dhcp.jsp.
but when im trying to boot the sun spac client with boot net:dhcp - install command it is failing with error "panic - boot: Could not mount filesystem.
Program terminated". exports file is ok and NFS service is also running.
Please help me on this issue.
Thanks in advance.
Shashi

Darren,
Thanks for the response.
I tried to install client60001dev (sparc client) from server60060pxe (linux jumpstart) as follows
client60001dev is able to get the IP address from server60060pxe DHCP and then the boot file also, but after that the client is not showing any NFS queries.
{0} ok boot net:dhcp - install
Boot device: /pci@1f,4000/network@1,1:dhcp File and args: - install
Using Onboard Transceiver - Link Up.
Timeout waiting for BOOTP/DHCP reply. Retrying ...
Timeout waiting for BOOTP/DHCP reply. Retrying ...
2aa00
Server IP address: xx.xx.xx.119
Client IP address: xx.xx.xx.111
Subnet Mask : 255.255.255.0
Using Onboard Transceiver - Link Up.
panic - boot: Could not mount filesystem.
Program terminated
tcpdump on server60060pxe
03:16:12.292836 IP server60060pxe.42445 > client60001dev.20759: UDP, len
gth 516
03:16:12.303646 IP client60001dev.20759 > server60060pxe.42445: UDP, len
gth 4
03:16:12.303669 IP server60060pxe.42445 > client60001dev.20759: UDP, len
gth 516
03:16:12.314479 IP client60001dev.20759 > server60060pxe.42445: UDP, len
gth 4
03:16:12.314501 IP server60060pxe.42445 > client60001dev.20759: UDP, len
gth 516
03:16:12.325313 IP client60001dev.20759 > server60060pxe.42445: UDP, len
gth 4
03:16:12.325347 IP server60060pxe.42445 > client60001dev.20759: UDP, len
gth 516
03:16:12.336158 IP client60001dev.20759 > server60060pxe.42445: UDP, len
/var/log/messages on server60060pxe
Feb 26 03:15:35 server60060pxe dhcpd: DHCPDISCOVER from 08:00:20:fe:4a:23 via eth0.
369
Feb 26 03:15:35 server60060pxe dhcpd: DHCPOFFER on xx.xx.xx.111 to 08:00:20:fe:4
a:23 via eth0.369
Feb 26 03:16:08 server60060pxe dhcpd: Dynamic and static leases present for 139.185
.168.111.
Feb 26 03:16:08 server60060pxe dhcpd: Remove host declaration client60001dev or remove
139.185.168.111
Feb 26 03:16:08 server60060pxe dhcpd: from the dynamic address pool for xx.xx.xx
/24
Feb 26 03:16:08 server60060pxe dhcpd: DHCPREQUEST for xx.xx.xx.111 (xx.xx.xx.
119) from 08:00:20:fe:4a:23 via eth0.369
Feb 26 03:16:08 server60060pxe dhcpd: DHCPACK on xx.xx.xx.111 to 08:00:20:fe:4a:
23 via eth0.369
Feb 26 11:16:09 server60060pxe in.tftpd[10266]: RRQ from xx.xx.xx.111 filename 8
BB9A86F
Feb 26 03:22:00 server60060pxe kernel: eth0.369: dev_set_promiscuity(master, -1)
Feb 26 03:22:00 server60060pxe kernel: device eth0 left promiscuous mode
Feb 26 03:22:00 server60060pxe kernel: device eth0.369 left promiscuous mode
Shashi

How to configure Oracle Linux 6.5 to request ip address from dhcp server

I have installed Oracle Linux 6.5 (minimal installation) on a virtual machine created on VMware vSphere 5.5. I have tried to configure dhcp during the installation by editing IPv4 Settings of System eth0 to use Automatic (DHCP) but somehow it does not work.
Then I changed the ifcfg-eth0 to use static ip address and that works.
Here is the content of /etc/sysconfig/network:
NETWORKING=yes
HOSTNAME=TESTOL
Here is the content of /etc/sysconfig/network-scripts/ifcfg-eth0 using static ip address:
DEVICE=eth0
TYPE=Ethernet
UUID=xxxxxxxx.xxxx-xxxx-xxxxxxxxxxxx
ONBOOT=yes
NM_CONTROLLED=yes
BOOTPROTO=none
HWADDR=xx:xx:xx:xx:xx:xx
IPADDR:##.##.###.###
PREFIX=24
GATEWAY=##.##.###.###
DNS1=##.##.###.###
DOMAIN:test.com
DEFROUTE=yes
PEERDNS=yes
PEERROUTES=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME="System eth0"
Based on my understanding, I should able to use dhcp by changing ifcfg-eth0 (I commented the parameters not needed for dhcp by adding #) but I have tried the following ifcfg-eth0 and it does not work:
DEVICE=eth0
TYPE=Ethernet
UUID=xxxxxxxx.xxxx-xxxx-xxxxxxxxxxxx
ONBOOT=yes
NM_CONTROLLED=yes
#BOOTPROTO=no
BOOTPROTO=dhcp
HWADDR=xx:xx:xx:xx:xx:xx
#IPADDR:##.##.###.###
#PREFIX=24
#GATEWAY=##.##.###.###
DNS1=##.##.###.###
#DOMAIN:test.com
DEFROUTE=yes
PEERDNS=yes
PEERROUTES=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME="System eth0"
I have also tried to add GATEWAY=##.##.###.### to /etc/sysconfig/network but that does not help.
I have checked that dhclient package is installed by using rpm -qa dhclient.
I'm new to Linux.
Thanks for any help

If this is your first experience with Oracle Linux, I recommend you perform a default installation instead of going minimal, which is just going to make things more difficult for no good reason. Enterprise Linux is not MS Windows and the difference between default and minimal installations do not compare.
You also do not want to use the rpm utility to install any software and use yum instead. The yum utility is standard. Rpm does not resolve software dependencies.
Your ifcfg-eth0 script is missing the line that specifies to use DHCP:
BOOTPROTO=dhcp
You can also use the network configuration utility, even in text mode, by typing the following at the command prompt of root:
system-config-network
If the above utility is not installed:
yum install system-config-network-tui
You will have to configure an appropriate yum repository file. The process is explained in the Oracle Linux release notes:
https://oss.oracle.com/el6/docs/RELEASE-NOTES-U5-en.html
See 3.2.3. About Oracle Linux Installation Media
Then insert the DVD or attach the DVD iso image to your virtual machine and mount it as following:
mkdir -p /media/ISOimage
mount /dev/cdrom /media/ISOimage
The path "/media/ISOimage" should be the same as you specified in the yum repository file.
After that you can use the yum utility to list or install software.

How to configure network virtualization in SCVMM 2012 R2 with two host

hi everyone... can you teach me how i configure networking in my infrastructure..
i am getting confuse that i have 2 phisical server, i don't know to set the netwokring in scvmm. Every best practice, i found in internet is using more than 2 physical server.
i have been tried before with the networking which i want..but it failed...
any one help me please...

This whitepaper should explain the required steps to get this working.
http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a
The whitepaper will use more than two hyper-v hosts, but you'll get the picture.
You can have 1 host to run your NVGRE VMs, while the other host should be dedicated to run the virtualization gateway VMs.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

How to configure bulk breaking articles in SAP retail

hi frnds...
This is my client needs...
How to configure bulk breaking articles in SAP retail for hyper market..
Scenario is like this... Ex: for MEAT
There should be a Parent article & child articles process.
i.e Chicken X - 100 corcoss is divide into child articles (A,B,C,D,E,F) like
Brest bone - 5kg     - A
leg pieces - 2.5kg   - B
wings - 2.5kg         - C
P - 7.5kg                 - D
Q - 10kg                 - E
R - wastage - 50kg - F
these child articles wont consider for inventory
So how to configure this scenario in SAP Article master & to run this process.
Pl help me out with scenario

Please have alook at
[http://help.sap.com/erp2005_ehp_03/helpdata/en/2b/b03889df3611d1953b00a0c930e0da/content.htm]
Material type WERT is correct.
In Material type maintenance you can control at all if a store will be value only inventroy managmenet or both.
Further in the Site master WB02, you can control it on MC level.
regards
B

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to configure windows services alerts in SCOM 2012 for all agent servers. For eg, Terminal Services, Netlogon, RPC etc..

Hi,
I need to configure different windows services alerts in SCOM 2012. Below are some of the windows services I need to monitor through SCOM.
Serivce: Windows Management Instrumentation
Service: Netlogon
Service: Remote Procedure Call (RPC)
Service: Server Service
Service: Terminal Services
Service: Windows Time
Service: Workstation
Service : WWW Publishing Service
Could some one please assist or share me the details, how to configure these services for windows agent servers.
Thanks..
Regards, Rajeev Parambil

Hi,
A certain set of services are monitored by default on all agents:
DNS Client
DHCP Client
RPC
Workstation
Server
For all the other services you could create a service monitor.
A nice blog series outlining this process can be found here: http://www.bictt.com/blogs/bictt.php/2011/03/16/scom-monitoring-a-service-part1
It's doing common things uncommonly well that brings succes. Check out my SCOM link blog:
SCOM link blog

How to Configure MS Exchange 2007 CCR and SCC Cluster in a single system

Hi i want to configure ms-exchange 2007 server for both SCC and CCR. i have two Windows Server 2008 on running on my hyper-v. by using cluster on both hyper v i want to install MS-Exchange 2007 for both SCC and CCR. ideally one windows server 2008 has
Active Nodes and another one has passive nodes. please guide me as i am new in the field

Duplicate of
http://social.technet.microsoft.com/Forums/exchange/en-US/edea43a1-59b4-4d26-9b41-76d0f4677095/how-to-configure-ms-exchange-2007-ccr-and-scc-cluster-in-a-single-system?forum=exchangesvrgenerallegacy#c6e08365-c01a-40aa-a8bc-94219757ef13
Blog |
Get Your Exchange Powershell Tip of the Day from here

Connecting two WRT54G wireless routers - how to configure

Hi All,
I have two WRT54G wireless routers. One is currently providing wireless access for several users at a local law firm. I need to connect a second wireless router for a user who works for another company in the same office. The second wireless router is basically going to be used for Internet access. The Office Manager at the law office does not want the user from the other company using their wireless router directly, BUT they will allow me to hook up the second wireless router for Internet access. I realize this doesn't really make sense in terms of security, but this is the scenario I must abide to. So I am wondering how to configure the second router. I am thinking that I connect a CAT5 from one port on the first router to the Internet port on the second router. I am also guessing that I need to assign the the second router a static IP with a different subnet such as 192.168.2.1. I am not sure if the first router still has the default 192.168.1.1. If the first router does use 192.168.1.1 would I need to change the IP on the second one to one on another subnet? Thanks.

You will need a setup like this:
Modem --- new WRT54G ---- existing WRT54G
192.168.2.1 192.168.1.1 ( "Local IP address" )
Modem connects to Internet port of new WRT54G.
LAN port of new WRT54G connects to Internet port on existing WRT54G.
SSID: different on each router (do not use "linksys" )
SSID broadcast: enabled on both routers
encryption: recommend WPA2, or at least WPA (can be same or different on the two routers).
passwords: different on each router.
channel: try to stay at least 5 channels apart. Usually channel 1, 6, and 11 work best, but any two different channels can be used.
Any "port forwarding" used by existing WRT54G must also be done on new WRT54G.
Both routers need a real login password (not "admin" )
New WRT54G will need "Intenet connection type" set to whatever is currently on existing WRT54G. Internet connection type for existing WRT54G will need to be set to DHCP.
Message Edited by toomanydonuts on 01-15-2008 01:54 AM

How to Configure my url in Apache server?

i have an Apache webserver.i want to give url as desired say.http://intranet.com. Now iam giving my machine ip address as "127.0.101:9000 "to get my html page displayed from a remote terminal in a intranet network.
How to configure the apache so that i can replace the ip address with my desired name url type. Please help me.

How to configure the apache so that i can replace the
ip address with my desired name url type. Please help
me.Apache cannot do anything about this . It is your network DNS and DHCP that does this for you .If u edit the hosts file in a pc on ur lan ,then u can invoke from this m/c with the string as long as ur m/c isnt re-booted .This is assuming that u do not have a static IP adress .

Best practice configure DHCP server NAC

hi all,
any idea how the best practice deploy dhcp on cas? i tired follow user guide configure dhcp on cas but still cannot running smoothly user just only grep ip authenticate.
- CCA agent very slow appear when user get ip dhcp on authenticate.any idea ?
- how to integrated profiler with nac appliance .?

Hi ahmed,
You have configured your CAS to be your DHCP server, Thats well and good because you are using Real IP mode, Which Supports the CAS to be a DHCP server.
Remember
This Setting is only For your Authentication VLAN that your client gets an ip While Authentication ok.
When your Client switches to Access VLAN , your client trafiic no longer flows through the CAS so CAS is now not responsible for DHCP.
You'll have to configure another DHCP on the Trusted Side which can Lease IPs to the Acess VLAN Members.
As you have configured OOB then your client is in Acess VLAN and does not come in contact with the CAS so you need the Trusted side DHCP to give the Client an IP address.
Here in your Scenario your ACCESS VLANS are 2022,2044
Hope this helps, Do reply after Testing.
Thank You
Regards
Edward

How to configure GlobeSurfer II umts modem router to act as just a modem

Sorry if this has been asked before but after three days of searching I haven't been able to find an answer.
I'd like to know how to configure a GlobeSurfer II umts modem router to act as just a modem allowing my TC to provide all the remaining wireless services.
I know the combination can easily be made to work with the TC as in bridge mode but doing that loses features of the TC that I'd like retain.
I've found a fairly comprehensive manual on line but it doesn't address my specific needs and I'm not techie enough to interpret the information that's provided into a work around.
Thanks

Hi Bob,
many thanks for answering. GlobeSurfer suggested the following
"the easiest is to use the Ethernet to connect the GlobeSurfer to your Capsule. Make sure that you have the 2 routers having difference IP address ranges and they don't overlap each other."
That pretty much contradicted everthing I've read in discussions so I've asked for information on how to
1. stop the GlobeSurfer from acting as DHCP and stop it providing IP addresses
2. make the GlobeSurfer a client of the Time Capsule
I was already using an e cable between the two but in the mean time I did the rest of what they sggested. The only warning I got on the TC was a "Double Nat" for which I clicked "ignore".
As a result I have the two networks that I wanted, (one protected with private HDDs and printer attached and one guest), I can connect to the internet through both, I've been able to extend the main using an Extreme in bridge mode and there's no sign of a third network being produced by the GSII. I'm delighted and I'm stunned to say that it worked.
It'll be interesting to hear what they come back with.
Thanks again

How to configure DHCP in Hyper-V

Similar Messages

Maybe you are looking for