How to configure ether channel

Hi mates,
As far as I know, when you configure ether channel (PAGP/LACP) on two ports, they act like one port. but in reality packets are not sent through both ports. Only one of the ports is used until the actual link fails.
Question is:
I have two switches, each has two SFP ports, I want to connect two switches each other.
how can I make ether channel always use both ports when sending/transmitting packets? I remember it is possible.
thanks for helping :)

HI
i hope this link will help u .
http://www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_example09186a0080094aec.shtml
when u create ether-channel it will automatically load balance based on source/destiantion mac address or source/destiantion ip address.
Thanks
Mahmood

Similar Messages

How to Configure internet channel to a relay SMTP server

Hi men,
My problem is How to Configure internet channel(or outbound mail) sending to a relay SMTP server. I want to test my spam software.
I have search and read Sun Messaging Administration document but haven't fought the guide.
./imsimta version
Sun Java(tm) System Messaging Server 7.0-0.04 32bit (built Jun 20 2008)
Thank and Regards,
Duc Tien.

tien86 wrote:
My problem is How to Configure internet channel(or outbound mail) sending to a relay SMTP server. I want to test my spam software. You can use the daemon channel keyword with the tcp_local channel e.g.
! tcp_local
tcp_local smtp nomx multiple remotehost inner switchchannel identnonenumeric \
pool SMTP_POOL maytlsserver maysaslserver saslswitchchannel tcp_auth loopcheck \
daemon relay.yourdomain.com
tcp-daemonIf the relay SMTP server only has an A record then use "nomx" instead of "mx".
http://msg.wikidoc.info/index.php/Mx%2C_nomx%2C_nodns%2C_defaultmx%2C_randommx%2C_nonrandommx%2C_nameservers%2C_defaultnameservers_Channel_Options
The "multiple" keyword instead of "single_sys" helps performance by increasing the number of emails per connection when sending to a relay system.
http://msg.wikidoc.info/index.php/Multiple%2C_addrsperfile%2C_single%2C_single_sys_Channel_Options
Regards,
Shane.

How to configre Ether channel?

How to configre Ether channel?
1.5

HI
i hope this link will help u .
http://www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_example09186a0080094aec.shtml
when u create ether-channel it will automatically load balance based on source/destiantion mac address or source/destiantion ip address.
Thanks
Mahmood

How to configure physical channel using DAQmx block(remote PXI6733)

I am trying to run the example in labview that use DAQmx. But I find I can't find the physical channel by browser or using DAQ assisstant. It reports "No supported device found". My PXI6733 is on a controller and communicate with host computer by TCP/IP. Could I use DAQmx in such environment? What I should do to find the physical channel?

Braver,
The NI 6733 is not yet support by NI-DAQmx. Thus, you will need to use Traditional NI-DAQ to program this device until this support is added. I would suggest that you examine the following Traditional NI-DAQ examples:
Examples >> Hardware Input and Output >> Traditional DAQ >> Analog Output
Good luck with your application.
Spencer S.

How to configure channels with Spring-Flex?

Newbie here trying to get my first Flex/BlazeDS app up and running.   I'm using the Spring-Flex integration and believe I have properly configured my servet and remoting destinations. My only remaining questions relate to how to configure the channels.
The use of the Spring/BlazeDS integration means that I do not have to have a remoting-config.xml file anymore. But it the documentation is unclear as to whether I need to configure my channels within a services-config.xml file still.
If I do need a services-config.xml file (and I think I do), how does one get away without hard coding the server URL? I've seen samples on the web like:
url="https://\{server.name\}:\{server.port\}/flex2gateway/cfamfsecure"
But I don't get when/where/what does the dynamic substituion? They almost look like Maven or Spring properties, but they can't be. Is this just something that has to be manually changed after installation?
Finally, I really don't like the idea of compiling the Flex client against a server-side configuration file as I have seen suggested on the web. How would one go about have the Flex client discover - or otherwise figure out what it needs to do dynamically?
Sorry for the multi-question post....thanks for any help!

You could load that info from an XML file as described below. I took this from the doc.
To further externalize configuration, you can pass the endpoint URL value to the client at runtime. One way to do this is by reading a configuration file with an HTTPService component at application startup. The configuration file includes the information to programmatically create a channel set at runtime. You can use E4X syntax to get information from the configuration file.
The following MXML application shows this configuration file technique:
<?xml version="1.0" encoding="utf-8"?>
<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml"
    applicationComplete="configSrv.send()">
    <mx:Script>
    <![CDATA[
    import mx.controls.Alert;
    import mx.messaging.channels.AMFChannel;
    import mx.messaging.ChannelSet;
    import mx.rpc.events.ResultEvent;
    private var channelSet:ChannelSet;
    private function configResultHandler(event:ResultEvent):void
        var xml:XML = event.result as XML;
        var amfEndpoint:String = "" + xml..channel.(@id=="amf").@endpoint;
        if (amfEndpoint == "")
            Alert.show("amf channel not configured", "Error");
        else
            channelSet = new ChannelSet();
            var channel:AMFChannel = new AMFChannel("my-amf", amfEndpoint);
            channelSet.addChannel(channel);
            ro.channelSet = channelSet;
            ro.getProducts();
    ]]>
    </mx:Script>
    <mx:HTTPService id="configSrv" url="config.xml" resultFormat="e4x" result="configResultHandler(event)"/>
    <mx:RemoteObject id="ro" destination="product"/>
    <mx:DataGrid dataProvider="{ro.getProducts.lastResult}" width="100%" height="100%"/>
</mx:Application>
The MXML application reads the following configuration file:
<?xml version="1.0" encoding="utf-8"?>
<config>
    <channels>
        <channel id="amf" endpoint="http://localhost:8400/lcds-samples/messagebroker/amf"/>
    </channels>
</config>

Ether channel between fiber optic ports any difference?

I will appreciate any help about the below questions.
there are two catalyst 4506 multilayer switches, Two SFP modules are installed on each switches for uplink purpose. (1000 Base SX fiber optic Gigabit ethernet SFP modules)
I want to connect two switches each other. Question is;
1.Can I bundle these two gigabit ports (ether channel) and get Two gigabit connection between switches ?
2.If I can do it, what happens if one of the lines fails?
I know I can configure ether channel between copper fast ethernet ports but I am not sure If I can benefit same feature for 1000 base SX fiber optic ports.
Thank you very much for helping :)

Hi Friend,
You can run a command "sh port capabilities " and that will how that whether that ports are capable of etherchannel or not.
Also AFAIK SFP ports are just the physical medium so it does not make a differece, they should be capable of etherchannel.
Also if one port of the channel goes down traffic will start trasversing through the other port so it will take care as redundancy. It will behave like other etherchannel which you cofnigure with copper ports.
HTH, if yes please rate the post.
Ankur

Ether Channel for WAN connection

We have 2 WAN connection from the ISP 2 links (155M and 300M) . We would like to perform a Etherchannel on this links.
Both the links termination are RJ45 to a Layer 3 switch. Can we configure Ether-Channel ? What is the condition for EtherChannel (eg no signalling from ISP) ?

If you're on an ethernet connection, you should be able to do etherchannel but like what the others have said, you're do not have the same speed for each, load-sharing wouldn't be optimal.
i'd rather do balancing via BGP by choosing what prefix gets advertised to a certain link, so I can at least maximize the two links. I have the same scenario before, I had 1 FastEthernet and 1 STM1 to a service provider, eBGP multihop load-share wouldn't cut it, I have to do manual prefix advertisement.
hope that helps.

ESW 540 and Ether Channels

We are trying to configure Ether Channels on our ESW 540 switches. We have configured the port(s) and made the physical connections but the Ether channel is only showing up at 1000M. It is my understanding that the port should be displaying at 2000M if configed with one pair of ports. Are there any other settings that need to be completed?
Thank you,
Brock

Is this forum inactive? Do I need to supply more information? Is this question not able to be answered?

ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (ex., 5 min) using the SLA?

I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability

Hey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris

How To Configure XI Receiver Communication Channel ?

Hi Expert,
I have a Scenario wherein i have 2 XI systems & i need to pass the messages between these 2 XI / PI system using XI Adapter. Can any body tell me how to configure the XI Adapter Step by Step. Is it required to Create the SM59 RFC destination with type H. Pl. Explain me in detailed.
Regards
Umesh

Hi Umesh,
In creating XI receover communication channel, you have 2 options for Addressing Type:
1. URL Address - no need to create RFC destination. You just have to specify the XI receiver host name, HTTP port, path (/sap/xi/engine?type=receiver), Authentication data (logon details for SAP Client number of the PI system).
2. HTTP Destination - create RFC destination in SXMB_ADM and specify the RFC destination name in your receiver communication channel.
For SAP documentation, see this link: http://help.sap.com/saphelp_nwpi711/helpdata/en/e1/091640a991c742e10000000a1550b0/frameset.htm
Hope this helps.
Regards,
Jenny

How to configure more than MIDI 16 channels in Logic Express?

The template song in logic only has 16 MIDI chennels.
But it is not enough for my usage. I have 10 MIDI out port in total.(8 on Motif by USB, 1 on audio interface, 1 on MIDI controller)
How can I use all these ports to expend my creation?
Thanks~

Hello srm2003,
(1) Build your NI MAX task for your device - picture 6259-01.png.
(2) DASYLab: Take a first NI-DAQmx Analog Input module, choose the MAX task and configure the channels 0...15 from device to 0...15 from module - picture 6259-02.png.
(3) DASYLab: Take a second NI-DAQmx Analog Input module, choose the MAX task and configure the channels 16...31 from device to 0...15 from module - picture 6259-03.png.
(4) Now you have 2 AI modules to handle the channels 0...15 (first) and 16...31 (second).
Best regards
MHa
Attachments:
6259-01.png ‏115 KB
6259-02.png ‏48 KB
6259-03.png ‏48 KB

How to configure an Alert message if communicationChannel(JMS) stops

All,
Is there a way how to configure an alert when the communication channel stops.
<b>Scenario:</b>
In the path Runtime workbench->Component Monitoring->Adapter Engine->Communication Channel monitoring, if we see that a communication channel has stopped(RED traffic light as Status), then can we trigger an alert notification for same.
Currently we have alrerts configured for any message/s failure in the JMS Adapter Framework. So can we trigger simmilar alerts when a comm channel stops(for whatever reason).
Thanks in advance
RK

Hi Sreeram,
Thanks for the quick reply.
We have a scenario where we activate individual channels at a given time. So in this case, Adapter will always be in RED as all queues are never running in our scenario.
So we need an ALERT to be triggered for individual comm channels. Is theer any way that you can think of ?
Thanks and regards
RK

How to use multiple channels with one remoteObject .

hi,
I have an application which is accessed through HPPS some
times , also it can be access on server with http service.
so I want to know how to configure config files or add
runtime channels which will support either channel depending on
the server it is accessed over.
Is there any one who can help me to solve this...i need it
soon.
thank you...

Hi,
Please visit the URL below for details on adding channel sets
at runtime. Add multiple channels to the channel set so that the
fall back mechanism works.
http://livedocs.adobe.com/blazeds/1/blazeds_devguide/runtimeconfig_5.html#194376
Hope this helps.

How to configure Oracle 10g Advanced Security to use SSL concurrently with

How to configure Oracle 10g Advanced Security to use SSL concurrently with database User names and passwords
In Oracle Advanced Security Documentation it is mentioned that i can use SSL concurrently with DB user names and passwords. But when i configure the client certificate on the client my DB connection is getting authenticated using the certificate, which out passing user id or password.
We want to connect to Oracle DB over SSL channel so that the data packets are not in clear text. Also we want the user to make a connection using user id and password.
Basically we want SSL with out authentication.
Need your expert advice

Read the documentation (I have given following links assuming you are running a 32 bit architecture)
Server installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14316%2Ftoc.htm&remark=portal+%28Books%29
Client installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14312%2Ftoc.htm&remark=portal+%28Books%29
You can find the required books (if not using 32 bit architecture) from
http://www.oracle.com/pls/db102/portal.portal_db?selected=3

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to configure ether channel

Similar Messages

Maybe you are looking for