How to configure http ports in AS Java 7.1 EHP1 ?
Hi all,
how can I create a new http port on AS Java 7.1 EHP 1 ?
I can't find this in nwa.
In AS Java 6.40 I use Visual Admin - Dispatcher - Services - http provider and then I can create many ports
( like (Port:50000,Type:http)(Port:50001,Type:ssl)(Port:80,Type:http) )
Thanks
Sven
Hi all,
thanks a lot for the answers:
@Patrick Whitty:
Whit your answer I've found the right docs in nwce711 and now I can solve my problem.
Many thanks.
@Fan Yu:
Sorry, maybe my thread was misinterpretative. I've installed Sap Netweaver CE 7.1 EHP1
Also many thanks for your answers. Future I will describe much more better.
@rkandy:
We have this option on our 6.40 systems (I have also in my local installation)
In Visual Admin -> Cluster -> Dispatcher -> Http Provider -> Propertie "ports"
I can send you a screenshot.
Regards,
Sven
Similar Messages
-
How to configure HTTPS in the receiver HTTP adapter ?
Hi Guys,
How to configure HTTPS in the HTTP receiver adapter and where i need to mention the QOS=BE in the receiver adpter.
any suggestions or help would be appreciated
Thanks,
SriniYou would need make sure that SSL is enabled on the ABAP stack . I rememver seeing a blog on SDN that shows how this is to be done.
Once you have SSL enabled in the ABAP stack ( you would also need to install the cryptographic libraries as a part of this exercise) , you would be able to use HTTPS and also provide the necessary digital certificates etc.
I have tried this with SOAP adapters etc but havent with the HTTP adapter but I dont see why this should be any different.
Regards,
Bhavesh -
How to configure Https in Project server 2010.
HI,
Can i any one help me,
How to configure Https in Project server 2010.
My server farm is 1.Test1(App & Wfe) 2. Test2(App & Wfe)
Both are load balanced wit NLB as abc.hyd.in
DO i need to Install certificate in two servers Test1 & Test2 or one server is enough ?
Can any one please provide me a link to configure Https for project server 2010 for Two Farms Servers.
Thank You, Kumar KSVThere is no special configuration for Project Server to have the IIS enabled, it follows the typical sharepoint SSL enablement, we might need some mor edetails on how your NLB is done is it hardware based, software based ? it all depends how you want
to architecht the system, you can enable the Https either on NLB or WFE, again depending upon how you want to enable it, you will need to install the certificates on both WFE or on NLB
Follow the blog below to configure the SSL:
http://epmxperts.wordpress.com/2011/03/05/extend-same-project-web-app-instance-for-different-protocol-authentication-mechanism/
http://blogs.msdn.com/b/sowmyancs/archive/2010/02/12/how-to-enable-ssl-on-a-sharepoint-web-application.aspx
http://www.sharepointconfig.com/2010/03/configuring-a-sharepoint-website-to-allow-ssl-connections/
Thanks | epmXperts | http://epmxperts.wordpress.com -
How to configure http server in oracle 10g
Hi
I am configuring apex 3.2.1 on oracle 10g 10.2.0 I need help how to configure http server bec i did not find any Apache file or folder in 10g if it is then how .
ArshadHi
I use to configure only this in $ORACLE_HOME/forms/server/forms.conf (and restart ias):
AddType application/x-orarrp rrp_
AddType application/x-orarrp-text rrpt
AddType application/x-orarrp-ps rrpp
AddType application/x-orarrp-pdf rrpa
AddType application/x-orarrp-rtf rrpr
AddType application/x-orarrp-html rrph -
How to Configure SMTP Port in ODI
Hi,
Someone know how to configure SMTP port in the ODI tool? I tried changing the port number in the odiparams but I still encountered an error:"Could not connect to SMTP host." when executing the odisendmail package object though I can access the SMTP Server thru tracetcp.
TIA,
Cathy950484 wrote:
Hi Bhabani,
Thanks for the quick response :) . I saw your post and its a nice approach in sending mail instead of using an odi package object odisendmail. However, the requirement is not to use the gmail credentials but to use the credentials provided to us. But I noticed that the port used for the SMTP server is not the default port number which is 25. So I am guessing that the reason why I cannot connect to the SMTP host is because of the port number. Do you know how to solve this?If you want to change the SMTP port then do the following
edit smtplib.py located at <ODI_HOME>/oracledi/lib/scripting/LIB
change SMTP_PORT to what ever port you want .
restart ODI
execute your mail sending program -
How to activate HTTP port in R3 system?
Hi All
In SMICM transaction i am not getting Http port. I think its not activated.
Can anyone please tell me how to activate HTTP port in R3.
Please help me?
Regards
SowmyaHi,
You just have to set the profile parameters that are described in the documentation that you should have read.
Regards,
Olivier -
Difference between the abap stack http port and the java http port
Hello,
Is there a difference if a call a webservice in the SAP PI via the abap http port or the java http port?
For abap it is:
http://pi.host.de:8035/sap/xi/engine?type=entry
For java:
http://pi.host.de:53500/XISOAPAdapter/MessageServlet?
Is it technical the same?
Which is your prefered port and why?
Thank you
Best regards,
Nils KlothHi,
I found the blog
Using the SOAP inbound channel of the Integration Engine
So the main differences are:
Advantage
When you send SOAP messages directly to the Integration Server, you reduce the message load on the adapter engine. This can improve the performance.
Restrictions
The SOAP inbound channel of the Integration Server does not support attachments. SOAP messages with content type "multipart" are rejected.
Nils -
How to configure https in java?
Dude,
I just know that If we need https page in our java web application we have to configure on server which we are using .
I am gonna use Jboss as my application server.Right now I am using Http protocol to log in my site.Despite security reasons my clients push me to make it as https.
As of my Knowlege , I know that its just server configuration but not know how ?
Please help me to fix this..Besides configuring, you will also need a HTTPS host certificate.
-
Oracle10g How to configure HTTPS to access EM in Linux
I have installed Oracle10g on Linux Enterprise Server on XEON-based server.
I can run Oracle Enterprise Manager (EM) via
http://127.0.0.1:5500/em
Since EM will be unsafe to run on the Internet without SSL, does any one knows how to configure and enable Oracle10g to enable SSL access? Which port does it use?1. Stop dbcosole
emctl stop dbconsole2. execute command (as following) and fill all questions
emctl secure dbconsole3. Start dbconsole
emctl start dbconsoleNow connect to https://<ip address>:5500/em
Since EM will be unsafe to run on the Internet without SSLIt's generally bad idea to "share" administration site over internet (unless you don't have some VPN tunnel), because if you have weak passwords for DB users then you are asking for problems. -
How to enable HTTPS Port in abap system
Hello All,
Hope all are doing great,can any one please tell me the procedure step by step how can i enable https port in my only abap system,is it required to enable ssl also for this?..
Regards,
SyedHi,
For enabling the HTTPS port you need to do alot many things
At first change the para meters in Rz10
icm/server_port_0 - PROT=HTTPS, PORT=1443, TIMEOUT=900
icm/HTTPS/verify_client - 1
ms/server_port_0 - PROT=HTTPS, PORT=1443
SE80 - Utilities > Settings > Internet Transaction Sevrer = HTTPS
and also check SMICM under Services HTTPS is not showing as Active
and still if you are facing any issue with the port check with the network team/firewall team whether any port is being blocked on the network/firewall.
Regards
Mohammed nizam -
How to configure a port channel with VLAN trunking (and make it work..)
We're trying to configure a port channel group with trunked ports to connect a NetApp HA pair. We want to create two data LIFs and connect them to the switch stack. We are trying to create 2 data lifs, one for cifs and one for nfs that are on different vlans.
We want the same ports to be able to allow multiple vlans to communicate. (trunked)
These data lifs should be able to fail over to different nodes in the HA pair and still be able to communicate on the network.
What this means is that we have to connect 4 ports each for each node in the NetApp HA Pair to the switches and create a port channel of some type that allows for trunked vlans. When we configure the ports, the configuration is as follows (below):
We are only able to configure an IP on one of the vlans.
When we configure an IP from another vlan for the data lif, it does not respond to a ping.
Does anyone have any idea what I'm doing wrong on the Cisco switch?
interface GigabitEthernet4/0/12
description Netapp2-e0a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
channel-protocol lacp
channel-group 20 mode active
end
interface GigabitEthernet4/0/13
description Netapp2-e0c
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
channel-protocol lacp
channel-group 20 mode active
end
interface GigabitEthernet6/0/12
description Netapp2-e0b
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
channel-protocol lacp
channel-group 20 mode active
end
interface GigabitEthernet6/0/13
description Netapp2-e0d
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
channel-protocol lacp
channel-group 20 mode active
end
interface Port-channel20
description Netapp2-NFS
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
spanning-tree portfast
spanning-tree bpduguard enable
endOur problem was fixed by the storage people. They changed the server end to trunk, and the encapsulation / etherchannel.
I like all the suggestions, and they probably helped out with the configuration getting this to work.
Thanks!
interface Port-channel20
description Netapp2-NFS
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
switchport mode trunk
interface GigabitEthernet4/0/12
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
switchport mode trunk
channel-protocol lacp
channel-group 20 mode active
interface GigabitEthernet4/0/13
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
switchport mode trunk
channel-protocol lacp
channel-group 20 mode active
interface GigabitEthernet6/0/12
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
switchport mode trunk
channel-protocol lacp
channel-group 20 mode active
interface GigabitEthernet6/0/13
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,511,519
switchport mode trunk
channel-protocol lacp
channel-group 20 mode active -
How to Configure HTTPs sender communication in XI
Hi,
I have a request for new interface setup, in which i need to configure HTTPs sender communication from a B2B server to SAP system. Scenario is to receive XML 0rders from HTTPs B2B system and convert to Idoc and post it to SAP.
Please could some one help on what needs to be done in XI for receiving XML order files from a HTTPs connection and what further needs to be done for processing to Idoc.
Thanks in advance,HI,
For testing purpose you can use the HTTP client and paste your payload.
Refer the below pdf for HTTP client what you do is copy and paste the code in note pade and save as .html file.
This link gives you a sample HTML code to create HTTP Client:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/66dadc6e-0a01-0010-9ea9-bb6d8ca48cc8
Thnx
Chirag Gohil -
I want XE to validate DTD references made in XML schema definitions. Metalink note 262708.1 refers to setting HTTP_PROXY environment variable/Registry value to do this through corporate firewalls.
Can I set this in XE? If so, how is it done on Windows XP?OK, for the record I set the HTTP_PROXY value in HKEY_LOCAL_MACHINE\SOFTWARE\ORACLE\KEY_XE to
http://<username>:<password>@<http.proxy.server>:<port>
which seemed to do the trick as far as basic MS HTTP/proxy/authentication is concerned. The proxy software/configuration thereon is another matter... -
How to configure the connection between AS JAVA and AS ABAP
Hello,
I have installed a SAP Netweaver 7.3 AS JAVA and I would like to connect this JAVA Instance with 3 ABAP Systems (ECC 6.0) .
On help.sap.com I have found the following instructions: http://help.sap.com/saphelp_nwpi71/helpdata/en/3b/0c4b428f96ab53e10000000a1550b0/content.htm
Could you please advise, if the above configuration steps are OK?
Or could you please help me with the exact procedure?
Thank you in advance!
NoemiNoemi,
I'm not sure how exactly you want to use ABAP and Java so it is hard to answer your question.
The link that you posted describes the steps to configure ABAP as a Security Assertion Markup Language (SAML) service provider. As a service provider, the AS ABAP enables you to off-load the authentication of users onto an identity provider. The identity provider enables you to federate identities across domains for Single Sign-On (SSO).
Check the following wiki page for a good overview of all the ways that you could connect to ABAP
http://wiki.sdn.sap.com/wiki/display/ABAPConn/ABAPConnectivityHome
Regards,
Ventsi Tsachev -
SG-500-28P How to configure switchport port-security violation setting
Is there a way to do switchport port-security violation {protect | restrict | shutdown} in SG-500-28P in case of a BPDU Guard violation?
Seems like the default option is shutdown and I don't know how to change it.
Thank you!Hi,
you can recover this Violation.By using below command:
To enable automatic re-activation of an interface after an Err-Disable shutdown,
use the errdisable recovery cause Global Configuration mode command. To
disable automatic re-activation, use the no form of this command.
Syntax
errdisable recovery cause {all | port-security | dot1x-src-address | acl-deny |
stp-bpdu-guard | loopback-detection | udld }
no errdisable recovery cause {all | port-security | dot1x-src-address | acl-deny |
stp-bpdu-guard | loopback-detection | udld }
For more information:
Refer this URL:page no :406
http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/Sx500/cli_guide/CLI_500.pdf
regards
Moorthy
Maybe you are looking for
-
How do I change my phone number on iTunes. On my phone just I can't download any apps due to a problem with the numbers not matching
-
Ipod Touch(4G) won't sync after iOS 5 update
After I updated to iOS 5 my ipod could no longer sync with my iTunes. When plugged in it will appear on the left of iTunes but the sync button is grayed out and unpressible. I have tried restoring a backup on the ipod, resetting to factory settings,
-
Hi Friends, What are the available reports in SAP for Vendor payment summary, which shows all kind of payments (Check payments (Check numbers), Wire payments, ACH etc) with vendor details in one report. I tried some standard reports which is not givi
-
I'm having difficulty with video txt msgs.
Video txt msgs that I send to my son for some reason are loosing the audio once he gets them. I test them prior to sending them and the audio is fine on my end, but when he gets them he says he can't hear a word. I haven't tried sending any to anyo
-
Converting from non-batch to batch management
Hi guys, Can you tell what is the best strategy to convert a system from non-batch managed to batch managed? Batch management should have been implemented from the start, but my client just realized that mistake. This is knowing that we already have