How to configure Intel pci8086,109a Network dapter

hi folks, a sI'm totally new to Solaris 10 so I can
use lots of help PLEASE.
After installing Solaris 10 11/06 on Dell 9150,
there's NO internet connectivity.
With some help I've added a line [i]pci8086,109a
pci8086,109a net pci iprb.bef "Intel 10/100/1000
Network Adapter" [i]to
/boot/solaris/devicedb/master and iprb"pci8086,109a" to /etc/driver_aliases and then
::devlinks & touch /reconfigure::
Please undo the entry in devicesdb/master. You don't need a .bef file. This was required when one used the older boot method and that too when one needed to network boot the system. With GRUB boot which available on Solaris 10 11/06 network boot is done using PXE protocol.
The problem is that Solaris does not recognize your device. The drivers are probed and attached depending on the entries available in /etc/driver_aliases. The entry the ethernet device is not in that list.
To obtain the correct entry,you would need to look at the output from prtconf -pv. Check for Intel or "Ethernet" in the output and look for the compatible properties. The entry would look something like "pci8086,1029.8086.109a". Note that actual entry should be based of the the entries from the "compatible" properties. The correct method to add an entry is use update_drv -a -i "pci8086,XXXX" Where XXXX is based on the output from prtconf -pv.
>
Still there's NO internet connectivity. Many, Many
thanx in advance. -Jags

Similar Messages

How to configure HP Designjet T610 network card.

Dear All! i have HP Design jet T610 with network card HP JetdDirect 620N & now i want to configure my plotter on network, i checked plotter setting & go to connectivity panel but there is no option to give it static ip or host name etc. so can some please guide me how i configure my plotter via network?

We have HP Designjet T610, it has already network interface card placing on the plotter, so i don't know that is Jetdirect or not?! How should i know that, also how to configure and include in the network? it saying "Jetdirect -> No" on the connectivity settings. Pls help?

TVSU - How to configure pointing to a network repository?

I have installed UR on the server. Created a share called \\svr\systemupdates\
I am trying to understand how to configure the SU on the client machine to "look" to that network repository for updates...
I have tried the following but maybe I am not understanding the terminology used?
The following keys are used to store the user name and password:
HKLM\Software\Lenovo\MND\TVSUAPPLICATION\UNC=<network share> HKLM\Software\Policies\Lenovo\MND\TVSUAPPLICATION\UNC= <network share>
HKLM\Software\Lenovo\MND\TVSUAPPLICATION\Pwd= <encrypted password>
What password is referred to?
When I use the mapdrv utility I have to use the administrator user and password in order to get the drive mapped (SBS 2003)
Some of the registry keys were not present on the client machine and I had to create them (X200 running Vista) SU ver 3.14
Any help or idiots guide to setting this up would be appreciated! Screenshot of correct registry config?
Thx!

I am also interested in how to get it to work!.

How to configure Lion Server as network time server?

I have Lion Server at the top of a small network of Windows 2K, Windows XP and Windows 7 machines.
I need each of those computers to synch their time to that of the Mac Server because this network operates without internet access.
I have tried various protocols from those machines to synch on the server's IP but they all fail.
It has led me to belive I need to enable a service to allow time synch to the managed computers.
But I can't find information on this. I keep getting directed to how to synch the mac to a time server or time machine configuration tips.
Thanks in advance

In Server Admin, select your server, click on Settings, then go to the General tab. You will see an option to enable the Network Time Server.

How to configure the drivers VGA & network wireless for Enterprise Linux 4

Hello
I have installed Enterprise Linux 4 for PC HP Compaq dc7700. The installation was successful but I cannot find linux software driver for VGA & NETWORK.
Where and how can I FIND and INSTALL the drivers VGA & NetWork for liunx Enterprise 4 .
The details of the driver for the display is
VGA=intel Q965/Q963 Express Chipset Family for HP Compaq dc7700 Convertible Minitower PC
and the driver name for the Network is Wireless D-link DWL-G520 PCI Adapter.
Thank you

Hi, Wesam
Please take a look the following link
http://h20331.www2.hp.com/enterprise/cache/317386-0-0-0-121.html
Generally HP compaq dc7700 is not supported with RHEL4.
so maybe you have to install their drivers manually.
For VGA driver, please refer to
http://www.intellinuxgraphics.org/download.html
For Network adapter ,please refer to
http://linux-wless.passys.nl/query_part.php?brandname=D-Link
http://madwifi.org/
Good luck
Jason

How to configure and test Profibus network using NI part number 780161-01 Master/Slave interface

I have purchased this board from NI. I have been in touch with Comsoft who it appears is the developer of this board. I have used the configurator II to try and build the network. The GSD file for my slave board is entered. I also can see the GSD file for the master. There appears to be no obvious way to test the bus from the configuration tool. I have tried the Express VI provided by Comsoft. Nothing happens. I have a purchased profibus cable with terminations installed. I know the cable works as another division has another Profibus master that does work using this cable How do I configure correctly for sure? How do I test?
Thanks
Rick
Solved!
Go to Solution.

Hi Rick,
First, ensure that you have the correct drivers installed on your system:
Make sure NI-VISA 4.2 or later is installed on your system.
First install 1.3x.x COMSOFT driver
Second install a DF PROFI II Slave and Master board in your PC-System.
Reboot your computer System.
Install the NI-PROFIBUS driver, instructions can be found here.
However, it sounds to me like you may have an issue with your bus configuration or with the GSD file. First, did you obtain the GSD file from the manufacturer or from profibus.com?
Also, common issues with the configuration include specifying an improper baud rate (supported baud rates can be found here), or an incorrect PROFIBUS address. Were you able to successfully save the bus configuration and generate the configuration database? Were you able to load the configuration database into the master device successfully as well?
If you are unable to resolve this issue, can you provide me with some more information about your system setup and error? What PXI chassis are you using, version of LabVIEW, operating system? What devices are you testing on the bus?
Julianne K
Systems Engineer, Embedded Systems
Certified LabVIEW Architect, Certified LabVIEW Embedded Systems Developer
National Instruments

How to configure Intel Pro/100 ethernet in PXI-8176 controller for RedHat Linux kickstart installation?

I have trouble configuring the Intel Pro/100 ethernet for the PXI-8176 controller during the kickstart installation. Did anyone have better luck?

Not with Linux but...
I had trouble setting it up for RT.
There is an issue with the chipsets used and the firmware of the 8176 when sizing the bus.
There was a KB article.
NI support should be able to chase down your details for you.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

How to configure network printer on solaris 10 intel based

how to configure the network printer in solaris 10
like hp laserjet printer/printers,

Very very easy.
Go to the print manager . (printmgr I believe or in the launch menu under preferences)
select add a network printer
Fill out the info. I find that the hpijs printer driver works better then the suggested foomatic on my hp 4000s. I could not print pdfs otherwise.
Other things to know is the protocol should be BSD (at least it works for me). And add the port to the destination so 192.168.0.1:9600 for example (for hp).
thats about it. To have it show up correctly in JDS you should probably add it to the printer list under the launch->preferences->printer preferences.

How to configure Netgear FA510C Network Card

I installed Solaris 8 (Intel) on my laptop(Compaq Presario
1275) and have NetGear FA510C network card to be
configured. When I installed Solaris, it didn't recognize
the network card, and I have no idea how to configure
this network card. Does any have any idea how to
install and configure this network card?
I'll appreciate your help.
cwpak

Try to use devfsadm -v to find the device
Then use ifconfig dnet0 (not positive this is the right syntax for SMC) to plumb the device.
Then use ifconfig dnet0 192.168.50.4 up
You may have to modify these files to get the IP to come up on startup and properly resolve:
/etc/hostname.dnet0
/etc/netmasks
/etc/resolv.conf
/etc/defaultrouter
/etc/nodename

How to configure network virtualization in SCVMM 2012 R2 with two host

hi everyone... can you teach me how i configure networking in my infrastructure..
i am getting confuse that i have 2 phisical server, i don't know to set the netwokring in scvmm. Every best practice, i found in internet is using more than 2 physical server.
i have been tried before with the networking which i want..but it failed...
any one help me please...

This whitepaper should explain the required steps to get this working.
http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a
The whitepaper will use more than two hyper-v hosts, but you'll get the picture.
You can have 1 host to run your NVGRE VMs, while the other host should be dedicated to run the virtualization gateway VMs.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

How to configure network with just 1 ethernet adapter?

I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Is it mandatory to have more than 1 network card to configure multiple ports? If not, what are the options available to deploy a Virtual Machine that can have applications which are available over the network. I don't have a separate network i.e. public network as well as management network is of same IP range.
I am having 2 node cluster using NFS for pools as well as repository.
~Yagnesh

yagneshg wrote:
I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Just enable the "Virtual Machine" role on the Management network that is automatically connected. You will then be able to add guest vNICs to the same network.
I am having 2 node cluster using NFS for pools as well as repository. I strongly recommend you get at least one more physical NIC for your server, if not two: running NFS and the cluster heartbeat and the guest traffic all over the same network is going to put a lot of data down the wire and you may land up in a situation where the cluster traffic is overwhelmed and a node reboots. You need to be very careful in this situation. Network cards are cheap and you should have at least two or three, I reckon.

How to configure HP Laserjet P1606dn on Network

Hi,
I have an HP LaserJet P1606dn, brand new and fresh out of the box.now I am trying to configure it for network printing.
My challenge is that the default IP address (according to the Self Test/Device Configuration page) is 0.0.0.0. Internet Explorer does not recognize that as a valid address, and I cannot change the settings on my computer to get onto a 0.0.0 subnet. This means that I cannot get to the webpage on the embedded web server to change the IP address to something suitable for the network.
I can't understand how i will configure this printer in network.Please provide procedure of configuring this printer in network ASAP.

Hi,
The printer dhould obtain an IP once you connect an ethernet cable, such an IP means that the printer is disconnected from your network.
Try replugging the ethernet cable into the back of the printer, then to the LAN port of your router, allow it 30-60 seconds and check again.
If the same persists, try swithint the cable into another port of your router and check for any difference.
If the same persists, try using another ethernet cable and check for any difference.
Finally, if any of those provide such an 0.0.0.0 IP address, try pluggin a direct cable between the printer and the PC and check of there is a difference then, that in order to understand if the issue remain within the router or the ethernet cord of the printer itself..
Please let me know of any change, as well as the results,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How to configure WRT350N as a router in a network wih a DSL modem/router

Hi,
I'll really appreciate if somebody please could give me some help.
The problem is that I have a Dlink DSL-2640B modem/router AND a Linksys WRT350N router, what I want to do is how to configure them so they both are in the same network, and the WRT350N has access to internet and the computers connected to the DSL-2640B.
Is that possible?....OR...the other option I was thinking was leave the DSL-2640B as a modem only, and have the WRT350 make all the routing wired and wireless.
I'll really appreciate your comments.
Regards.

As per my knowledge it is better to use the wireless router to provide connection to wired & wireless computers. Leave the DSL2640B as a modem, connected to internet port on wireless router.

HOW TO CONFIGURE GUEST NETWORK AND LIMITE BANDWIDTH

Dear all,
Please help me how to configure internet access rule and limited the bandwidth for guest network via TMG Forefront 2010.
Thanks you & best regards,
Hung Viet

Hi，
First you can create the new network set which is mapped to guest subnet, after that you can create access rule for this network set.
If you want to control bandwidth, you may need 3-party tool like this:http://www.bsplitter.com/
Best Regards
Quan Gu

How to configure a Network Interface?

Hey guys.
I'm very new to Solaris OS. I've now installed Solaris Express Developer Edition on my Laptop. After the restart of the installation,I find out, that my network don't work. I try to configure it with the network-admin-tool, but i can't add something, because the button "add" is nowhere in the window.
Is it possible, that Solaris don't detect the interface and how can I see it?
Thanks and sorry for the bad english :).

Look for *e[0-9] (as nge0, nge1, bge0, le0, etc.) in:
# dmesg | less
or:
# less /var/adm/messages
Exaple:
Oct 13 15:54:45 hostname nge: [ID 223987 kern.info] NOTICE: nge0: link up 100Mbps Full-Duplex
"Unplumbed" interfaces maight not show up in the kernel log as they are passive. To "plumb" all supported interfaces:
# ifconfig -a plumb
# ifconfig -a
(MS' ipconfig mimics ifconfig :o)
If it lists say 'nge0' and you don't have /etc/hostname.nge0 then:
# cat /etc/hostname.nge0
cat: /etc/hostname.nge0: No such file or directory
# uname -n > /etc/hostname.nge0
(or # echo nge0 > /etc/hostname.nge0)
Add the address to /etc/hosts and the netmask to /etc/netmasks and the defaultgateway to /etc/defaultrouter
Example:
/etc/hosts:
10.0.0.1 gw.fqdn gw
10.0.0.2 hostname.fqdn hostname nge0
/etc/netmasks:
10.0.0.0 255.255.255.0
/etc/defaulrouter:
gw
You can change things on the fly with the comands ifconfig and route, but these files must be edited for a persistent boot configuration.
You can list the entire PCI-tree with:
# prtpicl -v | less
Example:
:model Bridge device
:compatible (a2000003daTBL)
| pci10de,373.1462.7250.a2 |
| pci10de,373.1462.7250 |
| pci1462,7250 |
| pci10de,373.a2 |
| pci10de,373 |
| pciclass,068000 |
| pciclass,0680 |
:driver-name nge
To see if your interface has a driver look for the PCI to driver-mapping in /etc/driver_aliases. Also check http://www.sun.com/bigadmin/hcl/ and http://www.sun.com/bigadmin/hcl/hcts/install_check.html
(put /sbin and /usr/sbin in PATH, i.e. PATH=$PATH:/sbin:/usr/sbin;export PATH)
(use "more" if you don't have "less")

How to configure Intel pci8086,109a Network dapter

Similar Messages

Maybe you are looking for