How to configure IP address and hostname?

May I know any method to configure IP address and Hostname? besides change it from /etc/hosts and /etc/inet/hosts.
any other method?
Any command to change?

May I know any method to configure IP address and
Hostname? besides change it from /etc/hosts and
/etc/inet/hosts.
any other method?
Any command to change?Yes, to do it temperiorly you can use ifconfig command, but after the reboot, these things will go off.
The syntax is:
ifconfig <interface> <ip addr> netmask <input based on your nwt> broadcast <> up.
ex:
ifconfig ce3 180.144.67.40 netmask 255.255.0.0 broadcast 180.144.255 255
HTH,
Prabu.S

Similar Messages

How to change IP address and hostname in solaris 9

Hi experts,
I want to change IP address and hostname of the server , Plese give steps, or any precise document .
Thanks
Mohan
Message was edited by:
mohan_sr

did you already change your ip and host?
if not, do the following instructions:
* verify your hostname
- uname -a
- cat /etc/nodename
both should show your hostname
* alter your hostname
- uname -S newname
* verify the hostname
- uname -a
- cat /etc/nodename
both should show your newname
* edit /etc/hostname.ce0 (type ce0 depends on your net device)
- echo 'newname' > /etc/hostname.ce0
* verify /etc/hostname.ce0
- cat /etc/hostname.ce0
should show your newname
* edit the following files
- /etc/net/ticlts/hosts
- /etc/net/ticots/hosts
- /etc/net/ticotsord/hosts
replace old with new hostname
* edit /etc/inet/hosts
replace ip and hostname
* you have to look for
- /etc/inet/networks
- /etc/inet/netmask
fit yout data
After doing all changes you have to reboot your system.
Use ipconfig to verify network data

How to configure website address to http request

hi
How to configure website address to http request
(I want access JBOSS URL: http://localhost:8080/HIS/Login using website like www.HIS.com)
Please help me.

What I'm trying to do is connect my laptops built in wifi adapter to my home network and connect my usb wifi adapter to my phones hotspot then combine the bandwidth into one stream so that my speed is faster.

How to configure sales forcast and assign marketing budget

how to configure sales forcast and assign marketing budget

Hi,
As per my knowledge i am telling forecasting is done by Historical Data { MM & PP Module }
when you collect the data based that we have to plan every month how much you want to procure the raw material etc..,
that should be entered in the material master under "Forecasting" tab there we have to maintain monthly wise forecasting values
i think it should get some idea if i wrong please clarify
Regards,
Prasanna

How to configure the runtime and consolidation for a track in CMS.

How to configure the runtime and consolidation for a track in CMS.
I can see the track exists in CMS but the same doesnt pull up in the NWDS in the development configuration perspective.
I compared the given track with the one which gets pulled up in NWDS. Theres something called runtime system and consolidation which isnt defined for the track which is invisible.
Please advise , what are these required for. And how can we configure the same.

The runtime systems are defined for a track to setup the Transport path for any code changes....the Consolidation system is usually defined as a Virtual system for the track and used for comparison and fixing any broken or Dirty DC's ....that means it's not used as a Runtime System for Deployment as compared to DEV,QAT and PROD used for Deployment...
Hope it helps..
Regards,
Shikhil

How to Configure E-mail and Chat functionalities

Dear all,
How to configure E-mail and Chat functionalities for IC Webclient.
through IC Webclient ICI interface how can we configure E-mail functionality, As per my understanding, E-mails can be handled in a similar way of receiving phones.
Where these E-mails can be stored?, Where we define agent E-mail id?
being ICI is a multi channel support does it need SMPT server support? If No, would there be any difference in the functionality?
How does CHAT functionality works?
Please educate in above scenarios to get a better understanding.
Your help will be highly appreciated.
Best wishes
Raghu ram

Do you make any effort to search for your answers before you post your questions? ERMS is the email response system
The 2nd post on this board - Documentation for Interaction Center (IC) WebClient
There is tons of stuff here to answer your questions as well as show you the configuration. You need a 3rd party CTI solution to do chat that you will read about in the blog.
SAP Notes
759923 Frequently Asked Questions about IC WebClient
940882 Frequently Asked Questions about ERMS
882653 Frequently Asked Questions about Agent Inbox
1114557 SAP CRM 2007 Internet Browser Releases
1118231 Supported user interfaces for SAP CRM
981710 Support for Microsoft Internet Explorer 7.0
1144511 Blank screen when starting CRM WebClient or IC WebClient
1115493 CRM Web UI: Mandatory SICF services for CRM framework
992848 Mandatory ICF nodes for CRM WebClient UI Framework
IC WebClient Consultant Cookbook for CRM 2005
Online Documentation
Online Knowledge Products
Blog: How to Configure Contact Center Simulator User Interface (CCSUI)
Blog: What is Computer Telephony Integration (CTI)

How to enable ws-addressing and set ws-Reply to & message-Id ??

How to enable ws-addressing and set ws-Reply to & message-Id and all related properties. ???
I looked at the documentation but not sure how to do this.
Any Help is appreciated.

No it is not possible to add the xml file to the already compiled war and not compiling again.
There are only two ways to add the policy file to weblogic deployed web service.
1: through the policy annotation in the web service java file.
2: through the admin console if the web service is deployed as a separate war.
thanks,
sandeep

I need to know how to configure wi-fi and VPN on m...

I need to know how to configure wi-fi and VPN on my E61i.
everytime I search for any available WLAN,I find one(in my company)and when start browsing,it gives me(WLAN not found).
What should I do?

iOS: Connecting to the Internet

How to configure the sort and port of a SOAP address dynamically

Hi All,
In the wsdl we have the SOAP Address defined but in practice we would like to configure the host and the port. As the server on which the service resides may/will change.
For example:
http://usciq74.wdf.sap.corp:50077/sap/bc/srt/rfc/sap/CPM_PLANNING_HISTORY?sap-client=003
We would like to configure the proxy to point to say:
http://<host>:<port>//sap/bc/srt/rfc/sap/CPM_PLANNING_HISTORY?sap-client=003
What we see in the Proxy Code is:
port.setSOAPAddress(new com.sap.flex.ws.runtime.SOAPAddress("http://usciq74.wdf.sap.corp:50077/sap/bc/srt/rfc/sap/CPM_PLANNING_HISTORY?sap-client=003"));
How could this be achieved.
Please help.

Hi Sumit,
Thanks for the quick response. However, I do not want to change the host and the port in the wsdl. I want it to be so, that it will pick the host and port dynamically(as you have mentioned). However, in out case, the web service has the SOAP address hardcoded as <b>http://usciq74.wdf.sap.corp:50077</b>.
We would want to write something as http://host:port and then let it pick the host and port dynamically. How is that possible.
Best Regards,
Debashree.

How to configure MQ-FTE and IBM Datapower along with PI7.1

Hi Friends,
Can somebody guide me with the steps to configure MQ-FTE and IBM Datapower with PI7.1 for B2B communication?
Thanks,
--Sonal

1. What is the difference between JMS MQ and Native MQ? How to determine which one to use?Native MQ refers to a proprietary api provided by IBM in multiple languages including java so that applications running on these can communicate mq. IBM also provides JMS wrappers around this native api, so that a jms client can talk to mq using JMS API. This is called MQ JMS.
2. If native MQ can be used here, what are the steps to configure Native MQ on WLS in my situation?SOA suite provides a MQ Resource Adaptor which can be used to connect to MQ. The developers of this resource adapter would have used the native api to enable the adaptor to talk to MQ, so that you dont have to worry about it. However you will need to configure the properties of your local MQ ( qmgr , q name etc). This is done in the outbound connection pool properties of the resource adaptor.
please check this blog for how to do this : http://soa-bpel-esb.blogspot.com/2009/09/configuring-mq-in-11g-soa-suite.html.
Since your MQ installation is in a remote machine you will have to configure the following properties specific to your environment - hostname, port, server connection channel, along with the queue manager name and queue name
3. Do I need any foreign servers or message bridges to be configured?Not required for your case if you are using MQ Adaptor. Since MQ also provides a JMS transport , you would have required foreign servers if you have to use JMS Adaptor instead of MQ Adaptor. Native MQ is expected to be faster than MQ JMS as it doesn't have the extra JMS layer.

How to configure IP address thrugh web.xml doubts

Hello there
I want to configure my web application. How can i initialise the IP Address and ports through web.xml file?
thanks!

ashish.251985 wrote:
I want to configure my web application. How can i initialise the IP Address and ports through web.xml file?You cannot do that in the web.xml.
At least the port can be configured in one of the configuration files in the /conf directory of the application server. The exact details and procedure depends on the application server implementation. Read its documentations.

How to configure cRIO 9004 and link it with Labview?

Today i tried to connect the cRIO 9004 to my pc using the serial cable
but unfortunately the controller was not detecting on my pc. Then I
turned on the IP reset button and tried connecting it using LAN to get
an IP address but it also didn't work. I was looking for drivers on the
internet and NI website but I couldn't find any directly related ones.
Status light is blinking slowly and continuously(one flash every
couple of seconds). According to cRIO 9004 manual it indicates "That the
controller is unconfigured. Use MAX to configure the controller.
Refer to the Measurement & Automation Explorer Help for information
about configuring the controller".
I tried MAX but its still not detecting the controller to configure.
It would be great if you'll could help me out with this as I'm configuring this type of a controller for the first time.
Thanks and regards
Kavin

Hey,
First of all get sure that you have LV RT and FPGA as well as the NI RIO driver installed at your system.
Then the easiest way would be to use a crossover ethernet cable to directly connect the cRIO to your PC.
Give the PC a static IP Adress e.g. 100.100.100.100. Deactivate Firewall and Virus Scanners.
Reboot the cRIO with IP Reset Switch ON, then it should appear in MAX under Network Devices with IP 0.0.0.0.
Give the cRIO also a static IP like 100.100.100.111, set IP Reset switch to OFF before saving this settings.
Now you can install the software at your cRIO also via MAX.
Then you should be able to find it in LabVIEW by right-clicking "Project UntitledX" and "Add Targets and Devices".
There should be different tutorials online how to configure a cRIO or other Realtime targets.
Christian

How to change IP address and subnet mask without using the sys-unconfig ?

I have Solaris 10 x86. I've ran into problems using the sys-unconfig command
to change hostname and IP address.
How to I manually change the IP address and subnet mask values on Solaris 10 manually?
Thanks.

We just switched over a DNS server by using ifconfig, (same subnet), and killing named. seems to be working fine, anything I should look out for ?
steps:
Prep -
- change name in /etc/hostname.e1000g0
- change name and IP in /etc/hosts and /etc/nodename
- # uname -S dnsint02
Activate
- unplug old dnsint02
# ifconfig e1000g0 192.168.2.80
# kill -9 [PID of named]
Cleanup
- Remove old key on clients I SSH from.
- reconfigure backup software for new name/server combo.
Edited by: HarryC on Jun 25, 2009 9:29 AM

How to configure a shell and tube heat exchanger with Lab VIew to get data

HiI
In our undergraduate chemical engineering labboratory we want to configure our shell and tube heat exchanger with a DAq and Lab VIEW to get information about the temperaure (of the cold fluid stream being heated), the pressure (of the steam on the shell side of the heat exchanger) and the flowrate (of the water being heated).
Can anyone suggest thermocouples, pressure transducers and flowmeters to fit between the heat exchanger and the DAq?
P.S. the heat exchanger is already fitted with thermometers, a pressure gauge and a rotameter but we don't know how to connect these hardware to the DAq
Solved!
Go to Solution.

It sounds like you have enough information to pick out appropriate sensors, you just need to do the research. I would start looking through the Omega catalog, or give them a call - they're usually helpful. I can't take the time to spec out parts for you - that would be a lot of time spent on someone else's project. Most pressure sensors put out either a 4-20mA or 0-5V signal, either of which you can read through an analog input on a DAQ; measuring a 4-20mA signal requires a resistor to convert to voltage. Most of the NI DAQ boards can read a thermocouple on an analog input, but make sure that your hardware does support reading thermocouples. For accurate readings, use a device that has built-in cold junction compensation - for example, the SCB-68 connector block - and for the most accurate readings, get a board specifically designed for temperature measurement.
For the flow measurement, a standard, simple solution is an orifice plate. You put a differential pressure transducer across it, look up the appropriate equations, and use them to calculate the flow rate given the density of the fluid (which you'll be able to calculate from the pressure and temperature, since steam tables are widely available). There are other differential pressure devices available as well - at a previous job we used a V-Cone from McCrometer. If you call them they'll spec one for you - but get an approximate cost first to make sure it's within your budget.

How to Configure logical path and how to retrieve physical path for an IDOC

Hi ,
I want to configure logical path for an IDOC,
and then I need to retrieve Physical path from this logical path
using a FM (eg. FILE_GET_NAME).
How to configure the logical path for an idoc ?
Regards ,
Harshit Rungta

Using Logical Files in ABAP Programs
To create a physical file name from a logical file name in your ABAP programs, use the function module FILE_GET_NAME. To insert the function module call in your program, choose Edit ® Insert statement from the ABAP Editor screen. A dialog box appears. Select Call Function and enter FILE_GET_NAME. The parameters of this function module are listed below.
Import parameters
Parameters
Function
CLIENT
The maintenance tables for the logical files and paths are client-dependent. Therefore, the desired client can be imported. The current client is stored in the system field SY-MANDT.
LOGICAL_FILENAME
Enter the logical file name in upper case letters that you want to convert.
OPERATING_SYSTEM
You can import any operating system that is contained in the list in Transaction SF04 (see Assigning Operating Systems to Syntax Groups). The physical file name will be created according to the syntax group to which the operating system is linked. The default parameter is the value of the system field
SY-OPSYS.
PARAMETER_1
PARAMETER_2
If you specify these import parameters, the reserved words in the physical path names will be replaced by the imported values.
USE_PRESENTATION
_SERVER
With this flag you can decide whether to import the operating system of the presentation server instead of the operating system imported by the parameter OPERATING_SYSTEM.
WITH_FILE_EXTENSION
If you set this flag unequal to SPACE, the file format defined for the logical file name is appended to the physical file name.
Export Parameters
Parameters
Function
EMERGENCY_FLAG
If this parameter is unequal to SPACE, no physical name is defined in the logical path. An emergency physical name was created from table FILENAME and profile parameter DIR_GLOBAL.
FILE_FORMAT
This parameter is the file format defined for the logical file name. You can use this parameter, for example, to decide in which mode the file should be opened.
FILE_NAME
This parameter is the physical file name that you can use with the ABAP statements for working with files.
Exception Parameters
Parameters
Function
FILE_NOT_FOUND
This exception is raised if the logical file is not defined.
OTHERS
This exception is raised if other errors occur.
Suppose the logical file MYTEMP and the logical path TMP_SUB are defined as in the preceding topics and we have the following program:
DATA: FLAG,
      FORMAT(3),
      FNAME(60).
WRITE SY-OPSYS.
CALL FUNCTION 'FILE_GET_NAME'
     EXPORTING
          LOGICAL_FILENAME        = 'MYTEMP'
          OPERATING_SYSTEM        = SY-OPSYS
          PARAMETER_1             = '01'
     IMPORTING
          EMERGENCY_FLAG          = FLAG
          FILE_FORMAT             = FORMAT
          FILE_NAME               = FNAME
     EXCEPTIONS
          FILE_NOT_FOUND          = 1
          OTHERS                  = 2.
IF SY-SUBRC = 0.
WRITE: / 'Flag      :', FLAG,
         / 'Format    :', FORMAT,
         / 'Phys. Name:', FNAME.
ENDIF.
The output appears as follows:
HP-UX
FLAG :
FORMAT : BIN
Phys. Name: /tmp/TEST01
In this example, the R/3 System is running under the operating system HP-UX, which is member of the syntax group UNIX. The logical file name MYTEMP with the logical path TMP_SUB is converted into a physical file name /tmp/TEST01 as defined for the syntax group UNIX. The field FNAME can be used in the further flow of the program to work with file TEST01 in directory /tmp.
Suppose we have a logical file name EMPTY with the physical file name TEST, connected to a logical path that has no specification of a physical path. If you replace the EXPORTING parameter 'MYTEMP' with 'EMPTY' in the above example, the output appears as follows:
HP-UX
FLAG : X
FORMAT :
Phys. Name: /usr/sap/S11/SYS/global/TEST
The system created an emergency file name, whose path depends on the installation of the current R/3 System.

How to configure IP address and hostname?

Similar Messages

Maybe you are looking for