How to configure Mesh topology?

Hello,
Can someone help me? I need help setting up a MESH topology as seen in the attached file.
I've never configured a Mesh topology and I do not know where to start or even how it works and how troubleshoute?
What are the best practices? knowing that the indoor ap located in remote buildings seconnecteront the controller via the ap outdoors.
the ap they can all be in the same WLAN?
wlc : 5508
ap indoor : 1602
ap outdoor: 1552E
all ap can join controller
thank you in advance for your help.

The 1552's need to be setup as a RAP (the ap on the same location as the WLC) and the other two as a MAP. This is part one to get the MESH up and talking.
http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.4/design/guide/mesh74_chapter_010.html
The next thing you need to do is Ethernet bridging because you are connecting switches/device to the Ethernet of the MAP's
http://phasedcoexistence.blogspot.com/2011/12/cisco-mesh-ethernet-vlan-tagging.html?m=1
The tricky question is if the 1600's work behind a MAP. This is what you will have to test. The MESH AP's use a different ssid to communicate on the backhaul, so no matter what WLAN's you configure on the WLC, the mesh has its own. Vlan's are decided when you configure Ethernet bridging as the RAP now needs to be connected to a trunk port along with the MAPs if your going to use multiple vlan's. Or else all traffic will be passed to the native vlan or the vlan that the RAP is on.
Sent from Cisco Technical Support iPhone App

Similar Messages

Wireless Mesh topology parent child optimization. How do you force a reconfig?

Release 6 controller
9 Mesh APs. 1524 (2x 5G radios, 1x 2.4G) and 1522 (1x 5G radios, 1x 2.4G)
Designed for 3 linear hops and then a split to the rest.
AP1 = Root AP
linear to
AP2
Linear to
AP3
Linear to
AP4
equidistant to
AP5 and AP6
The rest are further away from AP4, but have visibility back to AP 4
The issue is after an event (say a power outage) at AP4.
AP5 uses AP3 as it's parent.
That's okay during the power failure, but when AP4 comes back up, I want to force AP5 to switch it's parent to AP4.
You may ask why, if AP5 can reach AP3 okay, it's okay to leave it that way.
Well, doing link tests...
test   --------packet loss %-----
speed AP3toAP5 AP3toAP4 AP5-AP4
===== ======= =======   =======
54M     100        0         0
48M     100        0         0
36M      52.6      0         0
24M       1.44     0         0
18M       0.89     0         0
So you can see it's desireable now that AP5 uses AP4 as it's parent.
Over time, the system might figure it out, but our limited experience shows it seems to stick to the way it is.
To complicate matters, sometimes we've found that it doesn't seem to reconfigure when the channel number has changed so AP5 can reach AP3, but AP4 (1524) comes up with a different channel on it's downlink radio.
So, how can we force a mesh topology reevaluation/change for either 1 AP or the whole bridge group?
I thought changing the bridge speed from "auto" to 54M (on AP3 above, for example) might force the attached children to rethink it, but it didn't seem to work (maybe I needed to wait an hour?).
I also thought tweaks to "Radio Performance Profile" for radio might help. (not sure what to change, or how long to wait for a result)
suggestions on how to quickly reconverge?
reseting APs and hoping they come back in a better topology is painful and slow.
Thanks - Glen

Glen, I know this is a very old topic but we are suffering from similar conditions on our end. Even using directional antennas we are having a difficult time having the Mesh network consistently optimize itself. Did you guys ever find a tweak that worked for you to have the system re-evaluate the connection by packet loss on speed?
Thanks!

A bit complicated mesh topology

Hi all!
I am trying to deploy a indoor mesh with LAP1262N APs and WLC 5500.
With a simple topology like this,
WLC ----- SWITCH ----- RAP ))) ((( MAP
clients can connect with all APs, but...
I want to connect another AP (I don't know if RAP or MAP) with the previous MAP via ethernet port, like this
WLC ----- SWITCH ----- RAP ))) ((( MAP -----PowerLineCommunication ---- RAPorMAP
Is not possible go to the switch wired from the last AP and is not possible connect the last AP via radio.
Well, in this scenario I can access and manage the last AP (RAPorMAP into schema) with WLC, but clients can't connect with the last AP.
Somebody know if it's possible use this topology? and, How I configure it?
Thanks in advance.

Why are you deleting the playlists form iTunes?
Leave them on there and you can sync them anytime you want you the iPod.
Since you find the software useful and actually use it, pay the small fee.

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to configure oracle listener profile for multiple oracle database

Hi,
I am going to install solution manager system in the same server of ERP EHP4 on Windows. Both DB are oracle.
I'd like to know how to configure listener in this kind of envirnmonent.
a. use two listener and different ports
b. use same listener but different ports
c. use same listener and same port
Which is the correct mothed?
And, after installation, there seem three set of profiles of listten, one for ERP, one for SLM, and the other for OS?(%windir%system32), which one is functional?
Please advise.
Thanks a lot.
Regards,
Alex

Hi,
standard installation is creating new configs for listener for each instance.
I would recommend to use one listener per each instance.
YOU CAN NOT HAVE one port number for two differnet systems!
If you want to use one listener than you must adapt tnsnames.ora, listener.ora and ensure that both systems will use different port numbers.
For example PORT= 15<system number>
Peter

How to configure one TREX host with multiple index servers ?

Hi All,
Does anyone know how to configure TREX on the one host,
with multiple index servers ?
Reason for this is to make better use of resources available on the host server(4 Gig, 4 Processor, Windows2003), to improve the search performance of
our KM content for portal users.
I am using TREX 7 and have not been able to do this,
despite reading the Single and Distributed install
documentation.
Any help would be appreciated.
Regards,
Andres

Hi Andres,
To make use of the RAM a Server provides you have to run two indexserver processes (each can then consume 2 GB);
Proceed like this:
1. Go to TREXdeamon.ini; check if section [indexserver2] is there (it is already provided, but not active in standard installation)
2. In TREXdeamon.ini go to
[daemon]
references sections below
programs=nameserver,preprocessor1,indexserver1,queueserver,alertserver
and add indexserver2 here. Restart TREX; second porcess is then started; can be checked in TREX monitor in Portal as well
3. To distribute existing indexes to the new process, start TREXadmintool and go to Index: Landscape
Go to the last two columns and move the indexes (move master here/secondary mouse click)
If you don't distribute the indexes the new index server process will be regarded when an new index is created.
Hope this helps!
cheers
Bettina

How to configure request manager service for multiple website in one web application

I have set up sp 2013 as below:
web application : wa1
site collection : sc1
sp site: site1, site2
I used 2 WFE, 1 APP, how can I use request manager service to control site1 to wfe1, site2 to wfe2?
Awen

That's not what i'd describe as load balancing.
A better description would be load-isolation. In your description then if the load on site1 was large (and growing) but site2 was quiet then site1 would struggle and eventually become unable to handle the number of users but site2 would still be ok. That's
fine from a QOS point of view but it's not the norm for load balancing. It would work in simple scenarios but the out of the box load balancing tools are much better suited than that sort of approach.
This article shows how to configure the RMS and may help show how your request is difficult to configure:
http://www.harbar.net/articles/sp2013rm2.aspx

How to configure 3 different members under a single Month column

Hi SAP Gurus,
My client requirement is to show the report in following format, where under a Month column 3 different columns having
1) Quantity (Number of unit ) of a product,
2) its rate (Amount per unit), and
3) Total (amount)    will appear in a single report.
   I have Month as a Time Dim, while Qty, Rate and Total are members of account dim.
Que: How to configure such scenario in a single report?
Jan.2011
Product Category:            Qty (Input)   Rate (Input)   Total (Output)
Product 1
Product 2
Product 3
Product 4
Group1
     Where: Total = Qty X Rate
Thanks and Regards,
SouarbhD

Hi,
Use an EVDRE to create your input schedule. You need to have one row with products and 2 columns with time and account. Choose the memberset options as per the requirement. For the accounts, is total calculated with a dimension formula? If yes, then you just need to enter the values for quantity and rate and send the data. The total will be calculated by the system and will be displayed automatically.
Hope this helps.

How to configure an Alert message if communicationChannel(JMS) stops

All,
Is there a way how to configure an alert when the communication channel stops.
<b>Scenario:</b>
In the path Runtime workbench->Component Monitoring->Adapter Engine->Communication Channel monitoring, if we see that a communication channel has stopped(RED traffic light as Status), then can we trigger an alert notification for same.
Currently we have alrerts configured for any message/s failure in the JMS Adapter Framework. So can we trigger simmilar alerts when a comm channel stops(for whatever reason).
Thanks in advance
RK

Hi Sreeram,
Thanks for the quick reply.
We have a scenario where we activate individual channels at a given time. So in this case, Adapter will always be in RED as all queues are never running in our scenario.
So we need an ALERT to be triggered for individual comm channels. Is theer any way that you can think of ?
Thanks and regards
RK

How to configure multiple IP addresses on one NIC?

Hi,
I just installed a OVM Server in version 3.2.1 and the according VMManager. Now i wanted to try to configure the Server/Server Pool. Now i come across a problem, which was already a big problem in OVM 2 while configuring the Networks.
All our OVM Servers have three NICs in them. One is for VMs and Management, the others are for connection to our SAN (Dell PowerVault MD 3220i). My problem is, that due to the network setup, the two NICs for storage need two IP addresses in two different networks each. This shouldn't be a problem, because usually in linux all you have to do is configure something like eth1:1. I remember having huge trouble configuring it in our OVM 2 cluster up to the point where I had to write a shell script to configure the second IP.
Anyways, I have configured two of the storage networks on eth1 and eth2 of the VM Server. Now i cannot configure any more IP addresses, because eth1 and eth2 are not available anymore for configuration in a third network. I really hoped that it would be possible in OVM 3 to configure multiple IP addresses. And probably it is only my lack of knowledge of how to configure it.
So any advice is well appreciated.
Thanks!
Regards,
Marek Hubatka

You should be able to do this by using "VLAN Groups".
http://docs.oracle.com/cd/E35328_01/E35332/E35332.pdf
Check out the VLAN groups section. You must great the VLAN groups before you can assign them to interfaces.

IAS 10.1.2-how to configure different oc4j listen to different virtualhost?

Hi
I have requirement,
we have oracle portal based web site that can be used by outside users over the internet.
And then we have are deploying few new apps/webservices/ear files on a oc4j called core_ws. These web services should not be accessed outside.
I have created a virtaul host in apache on a different port(7799) which was not exposed to public world.
But, how to configure core_ws to inform Apache to listen on only port 7799 but not on port 80?
I tried a diffent route to attack the problem(as mentioned below) which managmenet did not like:
created location directive, worked in dev but not in production as there ISA sitting front of apache.
We could apply filter on the URLs of these web services in ISA but my director did not like the idea as each time there is additional web service we have mess with it.
So, he prefers running these web services on a different port that will not have access to public.
Appreciate your help if have acheived the same earlier.

By your description, it sounds like you want to do what is in this My Oracle Support document:
How To Create Virtual Host Specific OC4J Applications (Doc ID 389819.1)
https://support.oracle.com/CSP/main/article?cmd=show&type=NOT&id=389819.1
(requires login)
You said you were using 10.1.2, so that will work, its a method of creating separate virtualhosts and using rewrites to direct to error pages if an incorrect request is made. For 10.1.3, but there is a dynamic method which is a better approach.
...Ken

How to configure sync with my local ftp server?

I have used XMarks since now because it hallow me to synchronize my bookmarks with my local server. Now XMarks don't work anymore because it's not more possible to synchronize the passwords.
Any other alternative imposes to use an external server and I don't want to use an external server. My data must remain on my machine it's absolutely excluded that i use an external unknown server for this.
The only solution must be a free solution (a real free solution) and the firefox synchronization seems to me the best/only one.
But I've not found how to configure it to use my own server.
So how to do it, where are the options to the synchronizer to give my own ftp server or whatever other server it needs?

iAS 6.0 sp4 officially does only support iPlanet Directory Server 5.0 sp1 and 4.13.
For more details visit: http://docs.iplanet.com/docs/manuals/ias/60/sp4/ig/prep.htm#42084
I guess, you can specify the directory server during the time of installation.
Thanks,
Rakesh.

ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (ex., 5 min) using the SLA?

I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability

Hey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris

I want to set up the Time Machine and I would love to use the Time Capsule but since I already have a wireless router I need suggestions on what other external disks Apple could recommend to use with the Time Machine and how to configure that disk

I want to set up the Time Machine and I would love to use the Time
Capsule but since I already have a wireless router I need suggestions on
what other
external disks Apple could recommend to use with the Time Machine and
how to configure that disk.
A complication that I need to resolve is the fact that I am using Vmware
Fusion to be able to use Windows on my Mac. Now it seems that Time
Machine is not backing up my files
on that virtual Windows without additional configuration and my question
is whether you can advise me here or whether this is only a matter for
the Fusion virtual machine.

If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it.

Don't know which technology to utilize or how to configure ASA5505

I have an ASA5505. Currently, it is using static NAT on several ports to forward traffic to several devices inside my network. It is a pain not only to configure but from the end user side.
The issue I am having is the applicatoins I am using to access the devices become a mess with dual configurations, one for when I am connected to the internal network and one for when I am away from the office and accessing from the internet. For example, I have 2 Cisco VC240 IP Cameras behind the ASA5505. One is set use port 9091 and the other 9092. When I am inside the office, I access them via http://10.1.2.215:9091 and http://10.1.2.216:9092. But when I am away from the office, I have to have another configuration in an Android app to use them, http://external_ASA_IP:9091 and 9092 and then NAT 9091 to the object for Camera1 and 9092 for Camera2. This is only one scenario. I also have a UC320W that I would like to put an IP phone at home and it sounds like AnyConnect is the only way to do this.
It sounds like to me that if I use some type of VPN, I can access the same devices using the same IP whether internal or external with the external connection using the VPN to tunnel the IP to the local network. There seems to be quite a few ways to do this with an ASA 5505.
AnyConnect seems like the way to go but after reading Cisco documentation, it requires your Android device to be root'd if it is not a particular Samsung model. If I understand correctly, root'ing your phone voids the warranty. I know it is common practice but would think Cisco would have a better solution as I am sure Cisco would not want another manufacturer telling their customers to void the warranty on their Cisco equipment in order to get it to work.
I believe I can just use IPSEC and use the native VPN of the Android OS and also tunnel L2TP as the Android supports IPSEC-PSK/L2TP or IPSEC-CRT/L2TP. But will either of these will support the IP phone to the UC320W?
A friend also told me to use NginX to proxy URL's so the URL http://www.fqdn.com/camera1 gets proxy'd to the internal IP of Camera1 and http://www.fqdn.com/camera2 gets proxy'd to Camera2. He says I should be able to store a cookie on the phone and let the phone authenticate to the camera and if the phone cannot, the proxy can authenticate internally to the IP camera over SSL.
I don't know anymore, I am so confused and just want to simplify my life as I am just a small business with me and a couple other employees but I have full-time job and it is not IT/Network Technician, it is only CTO/CEO/CIO/CFO. I don't have hours upon hours to set this up and test and I don't have hours upon hours to manage it. I just need to simplify this and have so that it is a set-it-and-forget-it for 6 months to 1 year and re-evaluate or update. So, if someone suggests IPSEC, I would not know how to configure anyway and you should expect another post. The same for AnyConnect or any of the other suggestions.
Thanks in advance for any advice.

Hi!
1. Set Calculation Mode property of ITEM_5 to Formula.
Formula property:
nvl(:Block_Name.ITEM_1, 0) + nvl(:Block_Name.ITEM_2, 0) + nvl(:Block_Name.ITEM_3, 0) + nvl(:Block_Name.ITEM_4, 0)
OR
Function_Name(Param_1,... Param_N);
Have in view of, that the ITEM_5 data will not be saved in DataBase.
2. When-Validate-Item trigger is usfull when is necessary to store calculated item data in DataBase.
Rename you Post-Query trigger to When-Validate-Item.
Modify trigger: Store calculation result in the variable.
(Don't forget to round variable value!)
Then compare it with ITEM_5. If they are different - :ITEM_5 := var_name.
I prefer the first method.

How to configure Mesh topology?

Similar Messages

Maybe you are looking for