How to configure MSI RG54SE II as Access Point ?

I have an msi router:
Firmware Version:
3.5.2 Build 070402 Rel.60023n
Hardware Version:
RG54SE II v1 081520C2
And i want it to configure it as an access point to a wireless network/ or another access point . Can you help me on how i do this ?
Regards,
Daniel

Hi. I Had a similar problem and found a solution. If you have another device as your primary router then:
1. connect ethernet cable from LAN port of your primary router to LAN port (NOT WAN!) of your RG54SE (I will just call it MSI).
2. go to web interface of MSI
3. if MSI has ip address in wan connection then release it. (Network->WAN) (I set my wan connection type to dynamic ip because there is no option to disable it)
4. in Network->LAN set ip address different from primary router (but in the same subnet) and out of DHCP pool
i.e. if your primary router has ip address 192.168.1.1 and its dhcp pool is 192.168.1.100-199 then you can set local ip address of MSI to 192.168.1.2
5. Disable DHCP on MSI router.
6. If your primary router also has active wi-fi then you must switch MSI wi-fi to another channel, so they do not interfere with each other.
that's it! It's simple and it works!

Similar Messages

How to configure wrt54g router as an access point when connected to a 3Com switch

I'm trying to use my linksys router as an access point to keep from having to make more network drops. I can't figure out which IP address/gateway to use on my router to get it to communicate with my switch. The 3Com switch address is 10.1.10.250, gateway is 10.1.10.1, netmask is 255,255,255,0.The linksys router has been reset to defaults.
I know that it can be done but I'm having the hardest time making it work.

For the DD-WRT firmware, you can try this link .
For the price of your Acess Point you can try this link .

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

How do I set the transition between access points would be fine?

Hello everyone,
We have an organization Wirless controller 2504 with 20 aironet access-point (700 series)
Once I defined all the access points I noticed that the transition between them is not working fine...
I mean that clients can not walk around in our organization without having to connect to any access point separately.
How do I set the transition between access points would be fine?
Thanks a lot (:

HI Omri,
which software version you have on WLC ?
Is the site survey done propely ?
Remember: It is the client that decides when to roam and which AP to connect to based on what it perceives the signal to be.
If your site survey design is perfect and still have problems while roaming then:
Disable your lower data rates on the 2.4ghz and or 5ghz radio and your clients will roam better. Try to disable everything below 11mbps. and give that a try.May be old device will work in this case.
Regards
Dont forget to rate helpful posts

How do I configure WRT54G as a wireless access point?

Ater a whole series of problems related to Vista, a WAP54G, Airport xpress, wireless printers, etc. plus at least three hours on the phone with Linksys tech support acessing my computer remotely and still not fixing the problems, I dumped my WRT54GC for a Belkin-N router. I set it up over the weekend and slowly regained internet access, then the pinter, then the Airports.
I still would like to have an access point because my signal strength even with the new N router is too weak downstairs to allow my PS3 to connect to it. I cannot figure out how to configure the WAP54G to make it work. I want to take a shot with the WRT54GC. From what I've read, I should be able to do it.
I can get into the router (referring to the Linksys) no problem. I can reconfigure it to an extent, changing the IP address to the recommended 192.168.1.2. I do this by running an ethernet cable from my PC to the router. Howver, after changing the IP address in the router I can't get into it any more using the new IP address. When I attach teh Linksys router to the Belkin I can't get in either.
Both the Linksys and the Belkin use 192.168.1.1 as the default IP address for each device.
I would like to know what settings I need to change i nteh WRT54G to turn it ino an access point -- an extenson of my existing network with teh Belkin router attached to the Comcast modem. I have looked at various how-to's and they all seem to assume I am connecting the two routers with an ethernet cable. If it's not clear at this point, I'd like to connect them wirelessly.
Thanks.

Thanks so much for the reply.
I was working with it all last night and somethign strange happened. After reading some other info on the internets, I changed the IP address on the WRT to 192.168.2.1. It updated, I then ran the wire from the Belkin to the WRT, I typed in 192.168.2.1, it took me to the Linksys setup page, but when I clicked "wireless" in the WRT setup, it took me to the Belkin setup page. How in the world did that happen?
Armed with tis new info, I did a hard reset on the WRT -- assuming it would change the WRT back to 192.168.1.1 -- got into the setup, turned off DHCP, left the IP as .1.1, and then wired it again into the Belkin. I can now get into the setup of either one.
Here's the thing: I don't want the two routers wired together. I want to move the WRT downstairs so a PS3 can pick up the signal. I want the WRT to wirelessly relay that signal to the Belkin to get the PS3 onto the net. I can't run a wire from the Belkin to the WRT.
I've read conflicting reports about whether the WRT can do this. Other sites suggest adding 3rd party firmware to add that functionality but that will definitely push the bounds of my abilities and likely exceed them. So, can the WRT even function in this way?
Inre the WAP, I don' know why but my ability to access the setup menu via 192.168.1.245 is very hit or miss -- much miss than hit. It makes no sense unless there is a bad connection somewhere because I hard reset, wire it to my laptop, put in the IP, and time out 19 times out of 20. I've got the MAC address for the router, and I think I know I want it to function as a repeater, but I've not been able to get that working right eihter.
Thanks for any further reply.

How to add a second router as access point and wifi signal extender

Previously I had 2 linksys routers and was able to configure them as one in separate areas of my house. I think it is called cascading. The 2nd router acted as an ethernet switch with 4 extra ports and it provided a wifi signal to areas of my house that previously had a weak signal when I used only one router.
I have since switched to an Airport Extreme as my main router. I can't seem to get the same configuration with the linksys router, it is Model E1000 and has an "N" signal. The Linksys E1000 I think is the newer model of the old WRT54G Linksys. I can't get it configured to work. I have searched high and low on the internet and can't find anything simple enough for a novice to understand. I did read something that I may have to assign a "DHCP Reservation" on the Apple Extreme. I couldn't figure that out.
Can somebody please offer some guidance on how to get this to work?
Thanks

You have two routers producing two networks with the same name, so they will show up as two networks on any type of scan by a wireless utility. This is normal.
If you had used two Linksys devices, they would probably show up as one network, not two. Linksys has a feature that allows this to occur, but this is not true of Apple devices.
As long as the wireless network name, wireless security and password match up between the two routers, the two networks will behave as if they were one. As computers change location, they will automatically connect to the wireless access point with the strongest signal.

How do i set up a wireless access point with ny time capsule

I am using a new Airport Extreme and want to utilize my older TC to create a wireless access point or maybe an aditional router using the same newtwork. What are the steps to set this up?
Thanks
Alamo

You will first need to perform a Factory Default Reset on the Time Capsule.
Resetting an AirPort Base Station or Time Capsule FAQ
Then, temporarily locate it in close proximity (same room or nearby) to the AirPort Extreme.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the tab in the upper left hand corner of the AirPort Utility window that reads Other AirPort Base Stations (1), then click the Time Capsule
AirPort Utility will take a moment or two to analyze your network, then announce that the TC will be configured to extend your wireless network.
Enter a name for the TC (you can use the same device name that you used before if you wish) and click Next.
AirPort Utility will take a another minute or two to configure the TC and then tell you that the setup is complete. Click Done
At this point, power down the TC and move it to a location that is approximately half the distance from the AirPort Extreme and the area that needs more wireless coverage.....to give the TC a good strong signal to "extend"
Power up the TC and wait for the green light and then you are all set.

How to Setup WRITTEN as a wireless access point to work with WRITTEN

Hi,
I had a router WRITTEN which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRITTEN saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRITTEN installed next to the internet modem connect to the modem by cable
2- in another room have the WRITTEN (approx 20 meters away) not connected by a cable to the WRITTEN
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRITTEN which should be also connected wirelessly to the WRITTEN
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

I am sorry but the spelling checker repalced my router names to another word
the correct text is:
I had a router WRT350N which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRT610N saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRT610N installed next to the internet modem connect to the modem by cable
2- in another room have the WRIT350N (approx 20 meters away) not connected by a cable to the WRT610N
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRT350N which should be also connected wirelessly to the WRT610N
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

How can I let applications let select Access Point...

The access point management of the 5800 is somewhat different from older phones: using Web you can select the access point every time you start it, but other applications using network (e.g. Opera Mini) start connecting Wifi or 3G whatever comes first. Then you can only select that that access point is selected automatically at next use. This means when you are in another country and the signal of a Wifi hotspot is too weak it will select 3G and does not notify the user of it, which will cost lots of money then.
Is there a possibility that I can select manually the AP at every application start like Web does ?
The older Nokias (e.g. E70) allowed to select the AP at every application start.
Nokia 5800
FW 30.0.011

The new "Destinations" method of managing the internet reflects the fact that many users now connect via several networks. A typical setup for the "Internet" destination might be:
Priority 1: Home WLAN
Priority 2: Work WLAN
Priority 3: Operator AP
This way, the phone searches for the various APs in order of preferennce when you access the internet, allowing you to use different networks without switching the AP in settings.
Individual applications may have their own AP settings which override the phone's standard setup - I can't speak for Opera Mini, but I can give N-Gage as an example of an application that ignores the phones main settings in favour of its own configuration.

How do I purchase an autonomous 1260 access point?

There's a new IOS release (12.4.25d-JA) with support for the 1260 access point in autonomous mode. However, I haven't been able to find a part number for purchasing this combination. It appears to me that I would need to do the following:
Purchase a lightweight 1260 (part number AIR-LAP1262N-x-K9)
Purchase a support contract so that I have access to software updates
Download the IOS image that supports autonomous mode for the 1260 (ap3g1-k9w7-tar.124-25d.JA.tar)
Replace the 1260's preinstalled lightweight IOS image by my downloaded image.
This seems unnecessarily inconvenient, as well as requiring the extra expense of a support contract. Am I correct in thinking that I would need to do this, or is it possible to order a 1260 that comes preconfigured with this autonomous image?

Hi,
I know this is off the original topic, but still. Since all indoor AP's like 1242, 1262 etc and outdoor AP like 1522 will have max transmit power of 17dbm or whatever the regulatory domain allows, what is the point in buying a 1522 for outdoor ? Cant i use the same 1242 with a protective NEMA enclosure and use the desired antenna with a 1242 instead of going for a 1522 ? Similarly if only 802.11abg is required, i guess the 1242 with its max power can provide as much coverage as any of the new 1262, 3502 etc ?
regards
Joe

How to assign static ip to lightweight Access Point 1131AG before registering to controller

Hi,
I have Wireless LAN controller which is installed in corporate office , we have enabled H-reap so that remote office access point can be registered with corporate office controller.
Now i have one AP at one of the remote site now i want to give static IP address to AP through console that too , before registering controller.
I have got console with below name :
......MAC Address....>
but if i type any command to assign IP address , it shows the error " Command Disabled "
I have attached details for more calrification.
As I know that I can connect this AP to corporate office LAN and get registered with WLC and then through WLC GUI , i can assign static IP address but i need solution to assign static IP before getting registered to WLC.
I will be obliged if i get proper solution

Hi Vinod,
I have already posted the bug ID and i request you to perform the work around specified in that.. i mean.. here it is again..
Ok... here is the BUG..CSCsy17745
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsy17745
lemme know if this helps and answers you after performing the work around!!
Don't forget to rate answers that you find useful
Regards
Surendra

How to Configure two standalone Server to access with eachother

Hi All,
I have two stand alone Servers (SQL 2000) configured in two PCs in different locations (Location A & Location B) . I want to access Location A database from Location B Viz-Versa.
1. I have a STATIC IP provided by ISP and I m using a router (Linksys E1000)
2. I have Windows Server 2003 installed on one of the PC.
3. Both the Locations are in two different places, ISP providers are also different.
How can I setup the access. I have googled a lot of solutions but not able to crack.
Regards
Pradeep

Hi Pradeep Sriramdas,
SQL Server 2000 was out of support since April,2013. I suggest you can try to install SQL Server 2005 or later version. According to your description, you plan to connect to the SQL Server database engine from another computer, you must enable the protocol
in SQL Server Configuration Manager, such as TCP/IP;
When you want to connect to one instance from another computer, you also must open a communication port in the firewall.
In SQL Server Configuration Manager, you need to configure SQL Server to listen on a specific port; In addition, you configure the remote access server configuration option in SQL Server by using SQL Server Management Studio or Transact-SQL.
You ‘d better adding two different computer in the same domain, and choose to connect to instance via domain name.
There are more details about configuring the connection from another computer, you can review the following article.http://technet.microsoft.com/en-us/library/ms345343.aspx
http://technet.microsoft.com/en-us/library/ms191464.aspx
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

How to configure WLS to send HTTP access log to syslog under Solaris?

I understand there is a way configuring WLS to use syslog via log4j. Is it possible only to direct HTTP access logs to syslog and keep the rest of logs in normal log files? Thanks!

I've been following the "How to do UD Document" https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/58f4db47-0501-0010-a2bf-ff01b150fdff and more specifically the document for Sybase https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/c0d70315-958f-2a10-bc88-eb91e36f4037
I am using the latest .jar file from Sybase http://www.sybase.com/detail?id=1002257
When I navigate to http://<hostname>:50000//TestJDBC_Web/TestJDBCPage.jsp and Select connection name SDK_JDBC I get the following error message:
Could not connect to database. Connection is inactive or does not support JDBC
com.sap.ip.bi.sdk.exception.BIConnectionFailedException: Cannot open the connection
Caused by: com.sap.ip.bi.sdk.exception.BIResourceException: Class DriverName is not found
Caused by: java.lang.ClassNotFoundException: com.sybase.jdbc2.jdbc.SybDataSource
Found in negative cache
Loader Info -
ClassLoader name: [connector:default]
Parent loader name: [Frame ClassLoader]
library:SYBASE
Resources:
   /usr/sap/BWD/JC02/j2ee/cluster/server0/apps/sap.com/com.sap.ip.bi.sdk.dac.connector.sapq/connector/connectors/bi_sdk_sapq.rar/bi_sdk_sapq.jar
   /usr/sap/BWD/JC02/j2ee/cluster/server0/apps/sap.com/com.sap.ip.bi.sdk.dac.connector.jdbc/connector/connectors/bi_sdk_jdbc.rar/bi_sdk_jdbc.jar
   /usr/sap/BWD/JC02/j2ee/cluster/server0/apps/sap.com/cafbwadapterassembly/connector/connectors/cafbwadapterassembly.rar/sap.comcafbwadaptercaf.bw.adapter.jar
   /usr/sap/BWD/JC02/j2ee/cluster/server0/apps/sap.com/com.sap.ip.bi.sdk.dac.connector.xmla/connector/connectors/bi_sdk_xmla.rar/bi_sdk_xmla.jar
Loading model: {parent,references,local}
Any thoughts/insites?
Thanks, Steve

How to configure OC4J to force the access only to one page after the log in

Hi,
I want to know how could I force the access to only one page of the web application when the user first time accesses.
I don't want to use session. Is there another way, say by configuring the OC4J configuration files?
Thanks

Hi,
you can write a servlet filter for the we application that checks if the accessed page is the login page and if not of the login page was accessed before
Frank

Help, How to configure cisco ASA5505 to permit access to internal LAN

Hi everyone,
Once more I am stuck into another dilemma , I have configured a Cisco ASA 5505 to allow VPN access from outside to my LAN using Cisco VPN Client software. The connection is establishing properly with the ip address from my VPNPool.
From outside (on VPN connection) I can ping the interface e0/0 (outside) and the interface e0/1 (inside) of the firewall, but I cannot ping the layer 3 switch interface to which the ASA is connected ( int gi1/0/22 ip address 192.168.1.2/30 ) and I cannot ping any vlan interfaces inside my switch. Therefore, I cannot connect to any server on my internal LAN.
I hope my explaination does make sense, I am available at any time if further information is needed. Please find attached my ASA config.
Best regards,
BEN

Many thanks Marvin,
I have configured the router ospf the way you instructed me, I have changed the VPN Pool to a complete different class of 10.0.1.0/24, I have also configured : access-list OUTSIDE_IN_ACL permit icmp any any echo-relpy and access-group OUTSIDE_IN_ACL in interface outside. but I can only from my VPN connection ping both interfaces of the ASA and nothing else.
Please find attached my ASA and the layer 3 switch configs. And also ASA and L3 Switch ip route output.
Note this: When connected to my VPN, cmd>ip config /all it showing as follows: ip address 10.0.1.100
                                                                                                                               Subnet Mask 255.0.0.0
                                                                                                                                Def Gateway 10.0.0.1
                                                                                                                                dns server 192.168.30.3
Best regards,
BEN.
Message was edited by: Bienvenu Ngala

How to configure MSI RG54SE II as Access Point ?

Similar Messages

Maybe you are looking for