How to configure network settings in solaris 10

hi
i have downloaded solaris 10 and installed on dell dimension desktop,as i have gone through the instalation guide,i see i dont get netwotk configuration (DNS,DHCP.....)settings during installation,it havent asked me about those settings,It just asked the host name ..after installation i see no network connection even i have my cable connected.ethernet cable connected Its INTEL
can anyone help me how to resolve this issue

You could try the Dell site, but I doublt if they will have a driver for Solaris, Linux maybe but not Solaris. Otherwise try the DriverGuide web site. http://www.driverguide.com/
You could also try installing OpenSolaris if you don't specifically need Solaris 10. Better chance that OpenSolaris will support the NIC.

Similar Messages

How to configure network on Oracle Solaris 10

Hi All,
I have created a new virtual machine on Windows Server 2003 and installed Oracle Solaris 10 on VMWare. Now I need to configure network on my Solaris virtual machine, So that i can access Solaris machine outside the VMWare. Can somebody help me out?
Regards,
S.Rizi

Hi,
I have created a new virtual machine on Windows Server 2003 and installed Oracle Solaris 10 on VMWare. Now I need to configure network on my Solaris virtual machine, So that i can access Solaris machine outside the VMWare. Can somebody help me out?Refer below thread.
Hope helps :)
http://www.linuxquestions.org/questions/solaris-opensolaris-20/configure-solaris-network-on-vmware-847849/
thanks,
X A H E E R

How to configure network printer on solaris 10 intel based

how to configure the network printer in solaris 10
like hp laserjet printer/printers,

Very very easy.
Go to the print manager . (printmgr I believe or in the launch menu under preferences)
select add a network printer
Fill out the info. I find that the hpijs printer driver works better then the suggested foomatic on my hp 4000s. I could not print pdfs otherwise.
Other things to know is the protocol should be BSD (at least it works for me). And add the port to the destination so 192.168.0.1:9600 for example (for hp).
thats about it. To have it show up correctly in JDS you should probably add it to the printer list under the launch->preferences->printer preferences.

How to configure Proxy server on Solaris 10 - SPARC

Hi All
Please guide on how to configure Proxy server on Solaris 10 - SPARC ?
What tool should be used?

Proxy configurations are most often done within the application software that needs that function and not necessarily done in the OS. That permits you to make very specific settings and not just generic global settings that could conflict with other software.
Can you tell us what research you have done on the topic?
For example, have you glanced through a Google search on "solaris web proxy" ?
If you are hoping to use a specific web server application your forum post might be better placed in a forum space for that software instead of in a general OS forum space. What application software will you be using?

How to configure network virtualization in SCVMM 2012 R2 with two host

hi everyone... can you teach me how i configure networking in my infrastructure..
i am getting confuse that i have 2 phisical server, i don't know to set the netwokring in scvmm. Every best practice, i found in internet is using more than 2 physical server.
i have been tried before with the networking which i want..but it failed...
any one help me please...

This whitepaper should explain the required steps to get this working.
http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a
The whitepaper will use more than two hyper-v hosts, but you'll get the picture.
You can have 1 host to run your NVGRE VMs, while the other host should be dedicated to run the virtualization gateway VMs.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

How to configure my netwok in solaris 10 to get an internet connection

Hi,
I am new to this forum and to Solaris in general. I am sorry if this question was asked and treated before.
I just successfully installed Solaris 10 on an intel based workstation. I have an ip address that shows that is "**static**". I have a Fios router which i can get to from Mozilla firefox by opening 192.168.1.1 but i cannot get an internet connection even to register my copy of of Solaris or to get updates.
In the network proxy configuration, I selected : Direct internet connection. My Ip address is 192.168.1.2. I believe it shoub be dynamic not static and if it is true how to cdit the settings to use DHCP. Your help is very appreciated. Thank you in advance.
Aerkadri

If you want your Solaris system to use DHCP, the cleanest way to do this is to run '/usr/sbin/sys-unconfig', let the system reboot, and tell it to use DHCP when it asks you to set up networking.
Mark

How to make proxy settings in solaris 10 i386

Dear Sir,
I need your help in making proxy settings in solaris 10 x86, as well as on SPARC.
i installed on virtual machine, and later i wanted to do the same on M4000 server. please help.
Why I need to set proxy?
I am on a co-orporate network, and it requires proxy to use internet to download packages for sun directly from sun machine.
What package I want to download?
I want to dowload CUPS to configure LINE PRINTER(ALIS5180).
What did i do to configure line printer?
1, i installed sun solaris 10 on a dell server to make it as a "print server"
2, with the print manager I configure "alis5180"
3, give the print command to test the printing.
4, I did not got success, coz it is not printing the document i want, it is printing junk.
5, i clear the cache of alis5180 printer.
6, reset all the emulations ANSI, IBM Proprinter III XL, Epson FX-1180, Printronix® P600 & P 5000/6000, DEC® LG01, HP 2564C, Tally line/dot matrix printer, Epson FX 1180,
MTPL, contextual arabic, Twinax (IBM 4234/4210/5225)/Coax(IBM4234), HP LineJet HPLP Series, HP 256X no success.
Conclusion:-
This is why I want to configure cups. and I need internet access on the print server to download the this package, and it require internet connection.
Regards,
Mky
Edited by: user9007339 on Jan 22, 2012 3:29 AM

You could try the Dell site, but I doublt if they will have a driver for Solaris, Linux maybe but not Solaris. Otherwise try the DriverGuide web site. http://www.driverguide.com/
You could also try installing OpenSolaris if you don't specifically need Solaris 10. Better chance that OpenSolaris will support the NIC.

How to configure network with just 1 ethernet adapter?

I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Is it mandatory to have more than 1 network card to configure multiple ports? If not, what are the options available to deploy a Virtual Machine that can have applications which are available over the network. I don't have a separate network i.e. public network as well as management network is of same IP range.
I am having 2 node cluster using NFS for pools as well as repository.
~Yagnesh

yagneshg wrote:
I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Just enable the "Virtual Machine" role on the Management network that is automatically connected. You will then be able to add guest vNICs to the same network.
I am having 2 node cluster using NFS for pools as well as repository. I strongly recommend you get at least one more physical NIC for your server, if not two: running NFS and the cluster heartbeat and the guest traffic all over the same network is going to put a lot of data down the wire and you may land up in a situation where the cluster traffic is overwhelmed and a node reboots. You need to be very careful in this situation. Network cards are cheap and you should have at least two or three, I reckon.

Internet connection not working: don't know how to change network settings

I have a Macbook Pro with an internet connection that normally works fine. However, in my apartment, we are provided with a cable modem that has only one ethernet cable hook-up. Since we needed atleast two ethernet connections for two computers, we bought a switch that we hooked into the cable modem to give us extra ethernet ports.
Recently, while hooking up my ethernet cord to the switch, I have not been able to connect to the internet. Network Diagnostics tells me my Built-in Ethernet is working correctly, but Network Settings are at yellow, and my ISP, Internet and Server have all failed. I have followed all instructions to check my connections, and restart the modem, switch and computer many, many times but there is no problem with any of these things. The other computer connects fine on the switch and cable modem.
Additionally, under Network in System Preferences, I am being shown that there is an IP address and Subnet mask, so I am assuming there is nothing wrong with the cord, modem or switch (which work fine on the other computer), but there is no Router number, which seems odd. If it helps narrow things down, I am also trying to connect to the internet via DHCP rather than PPPoE, which is what I normally use.
I am guessing I must have accidentally changed something to do with my network settings and it is not adapting to the cable modem any longer. Unfortunately, I do not know how to do this, nor what to change it to if I had to. My landlady knows nothing about what kind of network settings I need to connect to the internet service provider. Other than calling Time Warner Cable (who provides the cable modem with ethernet hook-up)is there anything else I can do or should be considering in order to get my internet connection working?

heather1688 wrote:
Recently, while hooking up my ethernet cord to the switch, I have not been able to connect to the internet. Network Diagnostics tells me my Built-in Ethernet is working correctly, but Network Settings are at yellow, and my ISP, +*_Internet and Server have all failed_*+.
I am having this problem if you find a fix please let me know. I have spent hours with apple trying to fix this. Im going on my third week with apple trying to fix this and i have a thread on this issue.
http://discussions.apple.com/thread.jspa?threadID=2104335&tstart=0

Configure Network Settings. DHCP is used unless otherwise specified

Hello
I have created a task sequence that is used in multiple domains.
In one domain DHCP is not configured and we need to use the "Bootable media that uses the Configmr infrastructure".
This bootable media is running fine when DHCP is enabled.
However, when I configure the network settings Manual in WINPE the client
can connect to the SCCM server.
After SCCM applies the OS image and reboots the network settings are gone and the Task Sequence crashes.
Is there a simple way to transfer the network settings from WINPE to the OS?

I usually use ZTINICConfig.wsf of MDT
to capture those network settings. That means that I add the following two steps to my task sequence:
A Use Toolkit Package step, to copy the MDT package;
A
Run Command Line step, with the command %Scriptroot%\ZTINICConfig.wsf /ForceCapture, to capture the network settings.
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude

How to configure tape to sun solaris server?

Hi
We have a tape "Quantum Super DLT 600 tape drive" connected to Sun solaris 9 and working properly.
Now we want to connect and configure it to Sun solaris 10 server. I want to know how we can do it?
I checked in st.conf file , "#tape-config-list=" is commented in both solaris 9 while in solaris 10 it is not there.
I think i will just have to connect the tape to new srver(solaris 10) and do a reconfiguration boot. Right??
Also, what do i need to do for connecting the tape back to solaris 9 server.
Thanks

You really don't need to reboot the server. Connect the tape to the server and type devfsadm -Cv. Then type dmesg and check whether Solaris detect the tape or not.
if not do a reboot and see.
after doing one of above, insert a tape to the tape drive and type "mt stat" and see you got any output about a tape.
Refer Solaris 9 and Solaris 10 System Administration Guides.
Edited by: Thusith.M on Jul 31, 2009 9:24 AM

How to configure Internet settings on Iphone 4, os 4.3

Hey I got replacement handset from apple store...But the problem is I lost my internet and mms settings ....How to configure internet and mms in os 4.3??Hey I got replacement handset from apple store...But the problem is I lost my internet and mms settings ....How to configure internet and mms in os 4.3??

There are none unless it's built in to the Skype app.

How to reset network settings

Hello, I cant figure out how to reset my network settings on my macbook pro
I'm doing this because recently, in an effort to make my wireless work better (just bought a new router and it works great) I added an internet proxy to my network preferences (I'm ignorant to what a proxy actually is) and ever since then facebook and espn do not work on my browser. This is the message it displays on Google Chrome:
Oops! Google Chrome could not connect to facebook.com
Try reloading: facebook.com
Additional suggestions:
Access a cached copy of facebook.com
Go to facebook.co
On Safari all it says is that it cannot connect to the surver. After some proding on chrome, it told me that I should unselect any proxy's that were selected so this is what hinted to me that the reason I couldn't access these sites had something to do with the proxy meddling I did earlier. Even after unchecking all proxy settings it still doesn't work. PLEASE HELP!!!

Ok It looks like it reset the settings on the network however I'm running into the same problem with the websites I'm trying to access. Do you know how to fix this?

How to configure SIP settings on Nokia E51

Hello to all.
I need help. I have
Username
Authentication Username
SIP address
SIP Password
Domain
Outbound Proxy
in one of big SIPs provider but i cant configure my phone work with it. Please help me. I allready installed SIP Voip settings from nokia store.

Have you checked out this post upon forum http://discussions.nokia.com/t5/Connectivity/Nokia-E51-SIP-Settings/m-p/481535/highlight/true#M24073 or this resource?http://www.voip-connections.com/wp-content/uploads/2011/06/How-to-configure-Nokia-E51-and-E71-to-con...
Happy to have helped forum in a small way with a Support Ratio = 37.0

How to reset network settings but keep Time Machine backup data?

I am having problems connecting to the Internet through TC but works fine with Ethernet directly to the computer. I would like to wipe clean the network settings in Time Capsule but not lose the Time Machine backups. How to do this?
thanks
Ken

Just perform a "hard" reset on the Time Capsule (TC). This type of reset will not erase existing backups on the TC's internal drive.

How to configure network settings in solaris 10

Similar Messages

Maybe you are looking for