How to configure old AirPort Base Stations with current Mac

Hi everyone,
I noticed that you can't use the current AirPort Utility to configure old AirPort Base Stations. I'm talking about the pre-Extreme models that only had 802.11b (Graphite and Snow). It won't find them and even entering their IP manually won't let you enter the configuration.
Copying over the older AirPort Admin Utility from a 10.3 system won't let you configure them either, the app itself runs fine though. You need to use an older PPC Mac with OS 9 or max OS X 10.3 if I recall correctly.
Is there a way to do it directly from a current Intel Mac running Leopard?
Thanks
Björn

*Airport Admin Utility* for Graphite and Snow
<http://www.apple.com/downloads/macosx/apple/application_updates/airportadminuti lityforgraphiteandsnow425.html>

Similar Messages

How to configure a Snow base station with Snow Leopard?

According to "Mac OS X v10.6: About incompatible software"
http://support.apple.com/kb/HT3258?viewlocale=en_US
...AirPort Admin Utility for Graphite and Snow 4.2.5 is incompatible with Snow Leopard.
I have a Snow AirPort Base Station, and AirPort Utility 5.4.2 doesn't seem to be able to see it. (At least I can't figure out how to make it do so.) Can it not work with a Snow Base Station?
Now what?

One solution is to keep a pre-Snow Leopard OS installation (either on another partition or external drive) and then boot from that when you need to configure the snow AirPort base station (ABS).
Another solution is to use another Mac running a pre-Snow Leopard OS to configure the snow ABS.
Since the snow ABS was discontinued 6 years ago I can understand why support is going away.
The last PowerPC was shipped only 3 years ago and that is not supported by Snow Leopard either.

Adding password to old Airport Base Station.

I need to password protect the old Airport Base Station (dual ethernet). I have tried the support documents but it did not work. I have an express plugged in and my Airport Utility only sees that one. I have tried plugging the old base station into the iMac with an ethernet cable but then got stuck.
I'm using an iMac with OSX 10.5.4.
Any help?
Thanks.

Ok, the version you just downloaded should be compatible with both Tiger and Leopard. It's primary purpose is for administrating the old 802.11b AirPort Base Stations, both the Snow and the Graphite. The new AirPort Utility replaces both the AirPort Admin Utility and the AirPort Setup Assistant. So between the AirPort Utility and AirPort Admin Utility for Graphite and Snow, you should be able to administer any of the AirPorts.
Do you still happen to have the old AirPort Admin Utility or AirPort Setup Assistant installed on your Mac? If so, this might be the reason for the error message.

How to control an Apple Base Station with 3rd-party wireless card?

I recently upgraded my early 2004 Power Mac G5 2GHz DP to the 802.11n standard using a Newertechnology MAXPower 802.11n/g/b Wireless PCI Adapter to communicate with my new "n"-standard 2TB Time Capsule. My G5 shipped with an 802.11g-standard Airport Card which I disconnected when I installed the PCI card to avoid hardware conflicts. The new n-standard wireless set-up works without a problem, but having lost the Apple Airport Card, I no longer have the ability to control/manipulate the Timecapsule via the third-party card e.g. I cannot connect/disconnect my internet connection or otherwise troubleshoot the base station.
So, the question is, how can control an Apple base station with a third-party wireless card? As it stands now, I must boot up my laptop just to see if I have a connection.
My thanks in advance,
T. North
Brussels, Belgium

Thanks for the assistance. Yes, I can indeed administer the Time Capsule from inside the Airport Utility, but I am still unable to connect or disconnect the Internet connection like you can with an Airport card (using the Airport drop-down menu.) If my ISP signal drops for whatever reason (which is does often) I have to boot up my laptop just to reconnect. Is there some feature within the Airport Utility that permits one to connect/disconnect the signal? If there is, I haven't found it yet.

How can I configure my AirPort base station to allow DCC sends?

It seems you cannot initiate a dcc send from behind an Airport. This is because you intially send a message to the computer you want to the send the file to saying 'here's what you want, come and get it.' Your computer then listens for a reply from the target machine. Now the Airport (I am guessing) doesn't know you're waiting, you just sit quetly waiting for a response. However the response does not seem to get past the Airport. That must be because when I try to initiate the dcc send the base station modifes the source address in the data to it's external ip. So what I get is the target machine trying to ask the basestation to send the file rather than my machine.
How do I get around this?

You will need to map the appropriate port through the base station to your Mac. See How do I use Port Mapping (Part I).

Can't set up Airport base stations with new MacBook Pro

i have a brand new, late-2013 15" MacBook Pro running Mavericks. my attempts, using this machine, to set up my sixth-generation, 802.11ac Airport Extreme and my brand-new, whatever-generation 802.11n Airport Express purchased yesterday at an Apple Store (that means it's the current generation, with the power cord) - these attempts all fail with Airport Utility saying it's joining the base station for about a minute and a half, after which it stops trying and says, "An unexpected error occurred. Please try again."
i can set up both of those base stations effortlessly with my iPhone.
furthermore, i seem to be able to use this MacBook Pro to set up my fifth-generation, 802.11n Airport Extreme just fine - even when it's all the way across the house and my attempts to set up the sixth-generation one, which is a foot away from my MBP, are failing.
why can i set these devices up with my iPhone and not with the newest, best, fastest, fanciest, most powerful laptop Apple makes?
thank you.

mmm...okay. thank you, Bob.
for now, i've got the base stations configured via my iPhone, and once configured, my MBP can see and use them just fine. it just irks the **** out of me that my brand-new top-of-the-line MacBook Pro can't handle this simple task, and should have to use a wired connection to set up my base stations (how archaic!). it may be the only device i have with me one day when i want to set up an Airport base station (okay, that's unlikely, but it's the principle of the thing, dammit).
are we sure this is a matter of bugs in Mavericks, and not a hardware problem with my MBP or something?
many thanks.

Old AirPort Base Station

I am trying to set a password on my AirPort Base Station, but Airport Utilities doesn't recognize it. How can I fix this?

Hi - which password are you trying to change? - and did you attach a computer that has the Airport Utility on it directly to the Extreme with an ethernet cable and try see it that way?

Old airport base station quits working several times and week and won't let

me change the password.
I changed the password on my ibook and reset the airport base station but it still will not change the wpa2 password to the new one. I'm changing the password to rule out anyone having hacked into the network. Several times a week the whole network goes down and I have to turn off power to the base station to get it working again.
I have plugged it into a battery backup ups but that has not prevented it from crashing.

Pick, a quick Google search for "Airport Firmware 5.5.1" yielded the following link:
http://mac.sofotex.com/download-122643.html
I sense you're getting frustrated - I have a gift for such perceptiveness. Anyway, I wish I could explain your problems but I have no magic bullet for what you're experiencing. All I can offer is to suggest you download and install the above firmware. Hopefully the link works; I haven't tried it. There may be other ways of obtaining 5.5.1 but none was immediately apparent from Apple. Once installed, stick with firmware 5.5.1. As I noted I suffered major problems with 5.6 and have heard anecdotal reports of similar problems with 5.7 though apparently they're much rarer. My Extremes run literally forever without problems so I hope yours can too.
Next, disable all the encryption on your network for the duration of your troubleshooting. Simplify things as much as possible - remove all but one wireless client from your network. Perform a "hard reset" of your Extreme and reconfigure it from new. Run things like that for a while and see if anything changes.
Is it possible you're suffering from poor power quality e.g. dropouts, surges, sags, etc? Have you tried a UPS or at least a surge suppressor? I had a spell last summer when the utility would shut off power for a half second a day, literally, a half second, once a day, every day, for weeks. It drove me nuts. They immediately stopped this nonsense the moment I started running my Airport off a battery.

This version of AirPort Utility doesn't support my old airport base station.

PLEASE how can i connect my old airport 802.11 with an airport utility that doesn't support it.
thanks

I laughed reading you, we are not all sheep.
Yes the link was removed by a robot certainly, on this good evening

HT3728 how do you switch airport base station controls from 1 computer to another?

I recently purchased a macbook air (love it!) and I'd like to change out the the airport base station control access to my new macbook air from the PC that I initially set it up with. Is this possible to do without having to do a factory reset on my airport base statsion? My PC is on the verge of klonking out any day...

You can access your Airport from any device that has the Airport Utility installed as long as you are hardwired or in range of the network - I am not familiar with the new Macbook - it might already have Version 6 in utilities - this is the newest version and it is somewhat streamlined - if you want the same functionality that you are used to in the Windows version, then try and download 5.6 for your Mac - you can also use the mobile version by downloading the app to an Ipad or Iphone but is also a less functional version.

HT4262 Can I extend a WiFi Network, using a 802.11n Airport Base Station with a 802.11g Airport Express?

Having a new Apple AirPort Extreme (802.11n) I need to extend the network since even the AirPort Extreme provides after about 30 Feet maximum only 50% signal strength in 2.4 GHz and maximum 41% signal strength in the 5 GHz band.
I have an Apple Airport Express (802.11g) but I am not sure that it can extend with it the network to get a better signal strength?
I know I can only use the Apple Airport Utility 5.6 to access the AirPort Express, but I can see also the AirPort Extreme though it (5.6).
Also, it seems that my "old" Wireless Motorola Cable Modem (SBG900) for the same distance (about 30 Feet), which is a 802.11g, gives still a better signal strength (62%) than the Apple Airport Extreme...
I guess I need the proper instructions how to, if it is possible.
Any intelligent answers available? Thanks.

This is very confusing. The AirPort Express Base Station has three settings (under "Wireless" in the AirpPort Utility 5.6) "Create a wireless Network", "Participate in a WDS network" and "Join a wireless network".
Whereas the first is self-explanatory the second and third seem to indicate, that a relation with an existing Network can be created. This is also indicated, when selecting as the "Wireless Mode:" "Join a wireless network" and then selecting "Wireless Network Name:" where then all available networks 802.11 b/g/n pop up you can choose which to use.
Now, it does not make any sense, that if all these settings and selections are available, that the AirPort Express cannot extend an existing network, considering that the AirPort Extreme, which is a 802.11b/g/n can be connected to. Even the AirPort Utility 6.0 sees the AirPort Express 802.11b/g but when selected alerts that "This version of AirPort Utility doesn't support this base station. Use AirPort Utility 5.6 to configure or manage this base station. AirPort Utility 5.6 is available at AirPort Service and Support." And as said, that AirPort Utility 5.6 sees everything and has said setting options.
The way as I see this it is, that if I can pickup an existing network, created with an AirPort Extreme 802.11b/g/n with an AirPort Express 802.11b/g and have the option to "Join a wireless network" such AirPort Express should be able to broadcast the picked up and joint network. Otherwise the setting options for the AirPort Express are nothing else than a distortion of reality to me.
Also, before I got the new AirPort Extreme 802.11b/g/n I had an AirPort Extreme Base Station 802.11b/g (gray) and there I was able to extend the network via the AirPort Express 802.11b/g.
So the above comments do not make sense to me.
Hope you understand that and have a better explanation available.

Use old apple base stations with a new one

Can I use an Apple extreme base station (A1034) with Apple express base station to use feaures like AirPlay and extend WiFi coverage?
Express station would be the main base then (A1034) would extend its coverage and use features. Would this work or is it too old?
Jamie

Thanks for the info.
You are going to run into some problems.
The Mac(s) running Mavericks cannot be used to set up or configure the older AirPort Extreme.
But, even if they could, there is no setting on the older AirPort Extreme to "extend a wireless network".
If you could permanently connect the older AirPort Extreme to the AirPort Express using an Ethernet cable, you would have some limited use, but you would need to have a Mac running Leopard, or Snow Leopard, or a PC to be able to set up the old AirPort.

How to configure an airport express a1264 with osx 10.9

We have two old airportexpresses- A1264. Bought in 2008. I would like to stream music from my computer to my stereo as I have done before. However I have bought a new Macbook air with OSx 10.9. By reading I have understood that older airports need older airport-programs to configure them. Tried to download a airport-program 5.6.1 from apples home page but my operative system would not accept it? What do I do? Buy new one :-)???

AirPort Utility 6.3.x, which is built into OS X 10.9.x will work just fine with the A1264 Express, assuming that the A1264 is operating correctly.

Can i control airport base stations with a Motorola Extreme Networks controller?

I currently have a WLAN that uses Airport Extremes, and I am looking for a way to control these centrally. A vendor is proposing a Motorola Extreme Network with new APs. Will the Motorola controller work with existing Airports?

As far as I know, the AirPorts can only be administered by using the AirPort Utility. Unless this Motorola offering mimics the AirPort Utility, I would doubt that is would provide an ability to replace it.
However, without additional information on what & how this Motorola Extreme Network is/works, it would be hard to say, whether or not, it would play "nice" with your existing AirPorts. I would also venture to say that this would not be uniqure to Apple router, but other vendor products as well.

I lost my connection with my AirPort Base Station when I upgraded to the OS Maverick. How can I get my system to recognize the base station again?

I lost my connection with my AirPort Base Station when I upgraded to the OS Maverick. I can still see the Internet, but the Time Machine cannot backup now because it cannot locate the AirPort base station. How can I resolve this issue?
Steps already taken with zero success:
1. Restarted the AirPort Base Station multiple times.
2. Restarted the Mac Pro multiple times.
3. Looked online for AirPort update for 6.3.2 version.
Other Apple products in my house can still see the AirPort Base Station, however my Mac Pro and Mac Book Pro cannot.
Please advise.

That information helps. If you want to use one of the SmartStor's disks as a repository for sharing your iTunes Library, then do not configure that disk as a RAID. Format it with Disk Utility using the Erase tab. Mac OS Extended (Journaled) is the correct choice.
Connect it to your Time Capsule, then use AirPort Utility to configure access requirements for sharing it on your network. It should appear as a shared volume in the Finder, available to all your Macs as you thought it should.
I also thought maybe the extra HD space would be added to the existing Airport Disk. It isn't.
Correct. There is no way to do that. The only way to increase the capacity of a Time Capsule's hard disk is to replace the Time Capsule (or its disk, if you are amenable to disassembling it) with a larger capacity model.
If you also want to use the SmartStor as a RAID, that is another story, and you should probably attack that problem separately.

How to configure old AirPort Base Stations with current Mac

Similar Messages

Maybe you are looking for