HOW TO CONFIGURE ORACLE RAC USING EMC STORAGE MULTIPATHING

Dear Team,0
Am in process of installation of ORACLE RAC 10.2.0.3 using cluvfy 10.2.0.3 with EMC storage (multipathing)
need ur help..i had done with following things...
1)i had done with prerequisite steps..
2)user equivalence .
3)cluvfy checks...
4)in process to install ORACLE RAC but the storage assign to server is EMC Clarion but the disk assign is having same name but diffferent
major number minor number...
pls let me know..
1)major number minor number with repect to voting ,ocr and asm disk..
2)while configuring EMC storage how same mojor and minor number are assign(if possible compltee steps)
Thanks
Upendra
9820011875

Hi buddy,
You should start reading the installation guide for Your plataform. it's well explained there.
Regards,
Cerreia

Similar Messages

How to install Oracle RAC using 11gR2 on Win 7 32 bit from scratch?

Hiii,
I am a fresher and I have a win 7 system 32 bit with oracle 11gR2.
I want to install RAC using two or more servers but I dont know too much about it.
I tried to search on google but all they are giving information in pieces(for win 7) or about Linux(Please tell me why its all Linux everywhere not windows).
Please let me know if there any site where I can find step by step installation from scratch.
What are basic requirements(/software if needed).
Thank you.

Hi,
First of all forget about Windows!! Oracle is mainly designed for Linux systems. Oracle runs as real multi-process on Linux machines whereas on Windows it runs as a single process with multi-thread.
Memory usage - huge pages,single CPU run queue, dnfs, storage systems... etc. lots of concepts exists.
Besides Windows is one of the most poorly designed operating systems, you should use it only to watch cute kitten movies on youtube... Believe me, you wouldn't want to learn Oracle on Windows...
So, install virtualbox and then setup Oracle Enterprise Linux on it as a first step... By the way you have to deal with DNS server for release 11.X, RAC, you may start with 10g for now.
ORACLE-BASE has all the installation steps explained detailly, search for "oracle base rac install" on google.
I also explained on my blog, but it is a little bit advanced installation using ZFS storage simulator. DNS server installation is also explained: http://ilkertaysi.com/2013/11/11/oracle-rac-installation-with-zfs-storage/

How to configure Oracle RAC for Wiki and Blog

Has anyone done Oracle RAC configuration for Oracle Wiki and Blogs?
Thanks,
Frank

Hi Andreas,
Thanks you for your help. I am trying to implement third party external LDAP authentication for APEX and Forms.
So I started with OID and SSO setup to create external Partner Applications. Some reason my oid and sso web login links are not working. I didn't find any errors. I need some help in finding the problem and direction, I already read docs on web but no proper direction. I appreciate your help.
Thanks

Re: How to install Oracle RAC using 11gR2 on Win 7 32 bit from scratch?

Hi,
I'd suggest to use the Virtual box(Free download from Oracle) and use the steps mentioned in the link.. for RAC Setup for your practice
http://www.oracle-base.com/articles/11g/oracle-db-11gr2-rac-installation-on-oel5-using-virtualbox.php
HTH

Thank you DK2010,
Your answer was very helpful to me but please tell me why everybody suggest about virtual box? Is is very important? and what is the benefit?
And I was checking that testing that branch option thats why this post become branch of my discussion.

How to configure Oracle 10g RAC on windown sever 2003

hi all
plz tell me
how to configure Oracle 10g RAC on windown sever 2003 can any body help me , give be any link
plz it is very necessary for me
Regards

Hello,
There are a good doc written by Philip Newlan at www.jobcestbon.com/oracle/RacOnWindows.pdf
Regards,
Rodrigo Mufalani
http://mufalani.blogspot.com

How to configure Oracle 10g Advanced Security to use SSL concurrently with

How to configure Oracle 10g Advanced Security to use SSL concurrently with database User names and passwords
In Oracle Advanced Security Documentation it is mentioned that i can use SSL concurrently with DB user names and passwords. But when i configure the client certificate on the client my DB connection is getting authenticated using the certificate, which out passing user id or password.
We want to connect to Oracle DB over SSL channel so that the data packets are not in clear text. Also we want the user to make a connection using user id and password.
Basically we want SSL with out authentication.
Need your expert advice

Read the documentation (I have given following links assuming you are running a 32 bit architecture)
Server installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14316%2Ftoc.htm&remark=portal+%28Books%29
Client installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14312%2Ftoc.htm&remark=portal+%28Books%29
You can find the required books (if not using 32 bit architecture) from
http://www.oracle.com/pls/db102/portal.portal_db?selected=3

How to configure Oracle Enterprise Manager for ASM RAC Database ?

Dears,,
We have two databases (Primary & Standby), each database has two instances
Database version: Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit
How to configure Oracle Enterprise Manager for this environment ?
I need documentation for this please.
Many thanks & Regards,,

Assuming an agent is running on the servers you want to monitor,
navigate to the Agent home page (Via setup --> Agent)
When in the agent home page select 'Add Database'and press [Go]
Assuming yopur database now gets recognized, select the Configure icon and enter the password for dbsnmp.
When done, press [Ok] to return to the agent home page.
Regards
Rob
http://oemgc.wordpress.com

How to configure Oracle SSO for OBIEE

Hi all
Can anyone help me saying how to configure Oracle Single Sign-on with OBIEE?
Basically I want to enable a common login for Dashboard and answers using SSO.
I am using OBIEE 10.1.3.4 on a Redhat Linux
thanks in advance

Hi...
See this, hope this what you want...??
If not .. ignore...
Thanks & Regards
Kishore Guggilla

How to configure Oracle jsp engine on OAS4.0.8.1

1. How to configure Oracle jsp engine on OAS4.0.8.1 for linux
2. How to set the parameter on OAS. The Ojsp document only give examples depict the syntax used when running in an Apache/JServ 1.0 environment

Anyone?

How to configure sendmail to use multiple LDAP servers ?

Hi everybody!
I have a sendmail running on Solaris 10 and a LDAP server(192.168.1.9) also running Solaris 10 OS. I have configured the sendmail the following way:
bash-3.00# ldapclient list
NS_LDAP_FILE_VERSION= 2.0
NS_LDAP_BINDDN= cn=proxyagent,ou=profile,dc=email,dc=reso,dc=ru
NS_LDAP_BINDPASSWD= {NS1}*********************
NS_LDAP_SERVERS= 192.168.1.9
NS_LDAP_SEARCH_BASEDN= dc=email,dc=domain,dc=ru
NS_LDAP_AUTH= simple
NS_LDAP_SEARCH_REF= FALSE
NS_LDAP_SEARCH_SCOPE= sub
NS_LDAP_SEARCH_TIME= 30
NS_LDAP_CACHETTL= 43200
NS_LDAP_PROFILE= default
NS_LDAP_CREDENTIAL_LEVEL= proxy
NS_LDAP_BIND_TIME= 10
I also have another LDAP server (IP 192.168.1.10). It is configured as a replicant of the 192.168.1.9 LDAP server.
The question is how can i configure sendmail to use both LDAP servers ?
The man pages explain how to configure ldapclient to use ONE server and what if want to use two or more? All the settings and the profiles the same.
Thanks in advance =))

Hi!
To add LDAP servers to the Solaris ldapclient, you might use the ldapclient command:
ldapclient manual -v -a defaultServerList="servera.yourdomain.com serverb.yourdomain.com"
But this is only failover, AFAIK the Solaris ldapclient does not perform loadbalancing by itself.
But I am not sure about your sendmail programm. Normally, sendmail has its own configuration
and can be configured to use LDAP e.g. for aliases etc.
Regards!
Rainer

How to configure oracle thin drivers for SUN APPLICATION SERVER

hi all,
I am working with EJB with oracle as back-end. I wants to know how to configure oracle thin drivers for the SUN APPLICATION SERVER. Please explain me breifly.
Advanced thanks to all the replies.
with regards,
/kumaraswamy.n

Kumaraswamy,
Did you try searching the Internet? Here are the results of my Internet search:
http://tinyurl.com/zo4gk
And one of the first hits in the list was this:
Deploying to a Sun Java System Application Server
Good Luck,
Avi.

How to configure Oracle Enterprise manager 11.2.0.1 for ASM instance

Hi All,
Please let us know How to configure Oracle Enterprise manager 11.2.0.1 for ASM instance.
Reagrds,
Vikas

Assuming an agent is running on the servers you want to monitor,
navigate to the Agent home page (Via setup --> Agent)
When in the agent home page select 'Add Database'and press [Go]
Assuming yopur database now gets recognized, select the Configure icon and enter the password for dbsnmp.
When done, press [Ok] to return to the agent home page.
Regards
Rob
http://oemgc.wordpress.com

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to prevent Oracle from using an index when joining two tables ...

How to prevent Oracle from using an index when joining two tables to get an inline view which is used in an update statement?
O.K. I think I have to explain what I mean:
When joining two tables which have many entries sometimes it es better not to use an index on the column used as join criteria.
I have two tables: table A and table B.
Table A has 4.000.000 entries and table B has 700.000 entries.
I have a join of both tables with a numeric column as join criteria.
There is an index on this column in table A.
So I instead of
where (A.col = B.col)I want to use
where (A.col+0 = B.col)in order to prevent Oracle from using the index.
When I use the join in a select statement it works.
But when I use the join as inline view in an update statement I get the error ORA-01779.
When I remove the "+0" the update statement works. (The column col is unique in table B).
Any ideas why this happens?
Thank you very much in advance for any help.
Regards Hartmut

I think you should post an properly formatted explain plan output using DBMS_XPLAN.DISPLAY including the "Predicate Information" section below the plan to provide more details regarding your query resp. update statement. Please use the \[code\] and \[code\] tags to enhance readability of the output provided:
In SQL*Plus:
SET LINESIZE 130
EXPLAIN PLAN FOR <your statement>;
SELECT * FROM TABLE(DBMS_XPLAN.DISPLAY);Usually if you're using the CBO (cost based optimizer) and have reasonable statistics gathered on the database objects used the optimizer should be able to determine if it is better to use the existing index or not.
Things look different if you don't have statistics, you have outdated/wrong statistics or deliberately still use the RBO (rule based optimizer). In this case you would have to use other means to prevent the index usage, the most obvious would be the already mentioned NO_INDEX or FULL hint.
But I strongly recommend to check in first place why the optimizer apparently seems to choose an inappropriate index access path.
Regards,
Randolf
Oracle related stuff:
http://oracle-randolf.blogspot.com/
SQLTools++ for Oracle:
http://www.sqltools-plusplus.org:7676/
http://sourceforge.net/projects/sqlt-pp/

How to connect oracle database using jsf

how to connect oracle database using javaserver faces with connection pooling

Here is one way...
http://jakarta.apache.org/commons/dbcp/

HOW TO CONFIGURE ORACLE RAC USING EMC STORAGE MULTIPATHING

Similar Messages

Maybe you are looking for