How to configure radio in 1812 router as client?

Hi,
I'm trying to setup six new 1812 routers as wireless clients in an existing wireless network. I want to use them as wireless bridges. Is it possible? I can't find any info about this case in the documentation. There is mentioned only one possible configuration - as root bidge.
Thank you,
Peter

This URL should help you:
http://www.cisco.com/en/US/products/ps5853/products_configuration_guide_chapter09186a008043ac55.html

Similar Messages

How to configure WRT350N as a router in a network wih a DSL modem/router

Hi,
I'll really appreciate if somebody please could give me some help.
The problem is that I have a Dlink DSL-2640B modem/router AND a Linksys WRT350N router, what I want to do is how to configure them so they both are in the same network, and the WRT350N has access to internet and the computers connected to the DSL-2640B.
Is that possible?....OR...the other option I was thinking was leave the DSL-2640B as a modem only, and have the WRT350 make all the routing wired and wireless.
I'll really appreciate your comments.
Regards.

As per my knowledge it is better to use the wireless router to provide connection to wired & wireless computers. Leave the DSL2640B as a modem, connected to internet port on wireless router.

How to configure Airport Express N router and Netgear G router with Extreme

I have a primary Netgear G router (WRT54G) connected to my cable modem box. I have an Airport Express N router streaming music in another room and also extending the wireless network.
I am planning to demote the Netgear router as a switch + wireless network extender connected to my home theater setup (dish+apple tv+ps3) and purchase a new dual band Airport Extreme connected to the cable box and acting as the main router.
My question is if its possible for the N devices to still use N network while the G devices not demoting the whole wireless network to G? That's the reason why I want the Extreme. If yes, how to go about doing it? If not, I will just buy a cheap switch and use that for the Home theater and leave the current setup alone. Anyone who has a similar network, please advice. Thanks!

My question is if its possible for the N devices to still use N network while the G devices not demoting the whole wireless network to G?
Yes. To do so, you would need to connect the Netgear to the new 802.11n AirPort Extreme Base Station (AEBSn) by Ethernet, and then, reconfigure it as a bridge (disable both its NAT & DHCP functions).
In this configuration, the AEBSn & AXn can provide the 802.11n network and the Netgear can provide the 802.11g network.

How to configure the AirPort Extreme Router to forward data to Warcraft3?

Your Router and/or Warcraft III are not configured to forward data, on the port Warcraft III is checking, to the other computers on your network.
That is why blizzard says I can't host warcraft 3 game, to make it simple... I need to open a port for Warcraft 3- How do I do it?

The directions were moved on the latest document update and actually start on Page 54.
Open AirPort Utility, select your wireless device, and then choose Manual Setup from the Base Station menu, or double-click the device icon to open its configuration in a separate window. Enter the password if necessary.
Click the Advanced button, and then click Port Mapping.
Click the Add button from the Service pop-up menu.
The public UDP and TCP ports should be set to 6112.
The private UDP and TCP ports should be set to 6112.
The private IP address should be the IP address of your Mac.

How to configure PL/SQL Developer with instant client

Hi buddies!
I want to install PL/SQL Developer. I should be installing instant client? I need to install PL/SQL Developer in my pc which is going to access the database from the server.
Please enlighten me.
Thank You.
Cheers!
Nith
Edited by: user645399 on May 12, 2010 4:26 PM

user645399 wrote:
These are the steps I followed.
<snipped>I do not see a problem with these steps at all. It is correct. Step 7 is redundant (due to where you placed the tnsnames.ora file) - it's only really needed when you place the file in some other directory where +%ORACLE_HOME%\network\admin+ no longer applies.
Note that the client itself, needs to load the InstantClient OCI DLL - and this DLL uses the environment settings and the rest to "do its thing".
If the client loads some other Oracle client DLL, then the bets are off that InstantClient will be used, never mind will work.
Only a single copy of a DLL can exist in memory. Thus if some other s/w is using some other OCI DLL, then that DLL is already loaded and will be re-used by all other client s/w. None will be able to use the InstantClient DLL itself.
So make sure that no Oracle client driver is loaded at all. Then ensure that when client s/w requests to load the OCI DLL, it is loaded from the InstantClient directory.
As far as I recall, the Win32 LoadLibrary() kernel call is made by the application - if the DLL is not yet in memory, the current directory (in the virtual machine for that Windows process) is used. If the DLL does not exist there, the %PATH% variable is used to find and load the DLL. The DLL usage counter is then set to 1. As more processes request the DLL, it is incremented. When a process terminates, the usage count is decremented. When it reaches 0, its unloaded from memory.
Bottom line to all this is that only a single DLL module (irrespective of the number and versions of physical DLL files on disk) can reside in kernel space, and you need to make sure that the correct physical DLL file is loaded by the kernel.

How to configure the ESS portal in ehp 6 server?

Dear All,
Pls advice me how to configure the ESS portal in my client server?
I want to create new iviews ,pages,workset and link them all to R/3,with total configuration steps please.
Thanks and Regards,
Pradip

hi pradeep ,
which version r u using wdjava or abap ? ......if ur using java you have to do all in home page framework and if you are using with launchpad from EHP5 better you can create it from launchpad by going to t -code LPD_CUST and select the ROLE:ESS and INSTANCE: MENU
REFER Below............
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/e09b3304-07d8-2b10-dbbf-81335825454f?QuickLink=index&overridelayout=true&38388417774934
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/21eb036a-0a01-0010-25a3-b2224432640a?QuickLink=index&overridelayout=true&5003637159921
http://wiki.scn.sap.com/wiki/pages/viewpage.action?pageId=31476&bc=true
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/108c31e7-b6a7-2d10-3692-c1a9f7a5c4dc?overridelayout=true

I want to set up the Time Machine and I would love to use the Time Capsule but since I already have a wireless router I need suggestions on what other external disks Apple could recommend to use with the Time Machine and how to configure that disk

I want to set up the Time Machine and I would love to use the Time
Capsule but since I already have a wireless router I need suggestions on
what other
external disks Apple could recommend to use with the Time Machine and
how to configure that disk.
A complication that I need to resolve is the fact that I am using Vmware
Fusion to be able to use Windows on my Mac. Now it seems that Time
Machine is not backing up my files
on that virtual Windows without additional configuration and my question
is whether you can advise me here or whether this is only a matter for
the Fusion virtual machine.

If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it.

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

How to configure router in bridge mode

Hi
I have 2 cisco 2621 series routers to be configured in bridge mode.
i'll be connecting this 2 routers using serial connection 128 lease line.
the problem is im not sure how to configure this 2 routers in bridge mode.
as far as i know, i need to issue the command no ip routing.
is there anything else i need to do?
can anyone guide me on how to configure
the router in bridge mode? is there any support page for this is cisco website?
thanks
Jega

Please check the link to the configuration guide below. It describes how to configure transparent bridging.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_configuration_guide_chapter09186a00800ca65a.html
Regards,
Leo

How to configure routing on site to site VPN(RV215W)

Hi all
I have set up a VPN between a RV215W and SRP521 (site to site)
The VPN is up and connection is established on both side.
However I cannot connect from one network to another (No ping, no connection)
When I checked teh configuration, I noticed that route table on RV215W does not show any ipsec interface nor the route to the remote network
Any hint how to configure this route over the VPN? Should I do it manually or is it a paramater to be made automaticaly?
On the SRP215 the routing is as follow
Destination LAN IP
Subnet Mask
Gateway
Interface
192.168.100.0
255.255.255.0
VLAN100
192.168.15.0
255.255.255.0
VLAN1
192.168.25.0
255.255.255.0
141.48.36.1
ipsec0
41.0.0.0
255.0.0.0
WAN1
41.0.0.0
255.0.0.0
ipsec0
0.0.0.0
0.0.0.0
141.48.36.1
WAN1
On the SRP only local and WAN are displayed

Hi,
Don't worry about your English - it is good. I am not a native English speaker, either.
You are correct - Cisco's IS-IS has no internal support for optional metrics. The only metric value that is going to be used in best path selection is the default metric. Regarding considerations about metrics in IS-IS, the only consideration I find important is that all new IS-IS deployments should use wide metrics. These can be activated using the metric-style wide in the router isis configuration. Wide metrics allow you to use a significantly wider metric range than the original IS-IS standard: 24 bits for interface metric, and 32 bits for total path metric. It is important to say that all L1 routers within an area, or all L2 routers in the domain must use the same metric type, either the classic (also called narrow) or the new wide metrics.
Apart from that, there are no special considerations I am aware of. The choice of metric values for a particular interface is completely up to you. Of course you might want to configure lower metrics for faster interfaces (and vice versa), but what values you choose is up to you.
Best regards,
Peter

How to configure GlobeSurfer II umts modem router to act as just a modem

Sorry if this has been asked before but after three days of searching I haven't been able to find an answer.
I'd like to know how to configure a GlobeSurfer II umts modem router to act as just a modem allowing my TC to provide all the remaining wireless services.
I know the combination can easily be made to work with the TC as in bridge mode but doing that loses features of the TC that I'd like retain.
I've found a fairly comprehensive manual on line but it doesn't address my specific needs and I'm not techie enough to interpret the information that's provided into a work around.
Thanks

Hi Bob,
many thanks for answering. GlobeSurfer suggested the following
"the easiest is to use the Ethernet to connect the GlobeSurfer to your Capsule. Make sure that you have the 2 routers having difference IP address ranges and they don't overlap each other."
That pretty much contradicted everthing I've read in discussions so I've asked for information on how to
1. stop the GlobeSurfer from acting as DHCP and stop it providing IP addresses
2. make the GlobeSurfer a client of the Time Capsule
I was already using an e cable between the two but in the mean time I did the rest of what they sggested. The only warning I got on the TC was a "Double Nat" for which I clicked "ignore".
As a result I have the two networks that I wanted, (one protected with private HDDs and printer attached and one guest), I can connect to the internet through both, I've been able to extend the main using an Extreme in bridge mode and there's no sign of a third network being produced by the GSII. I'm delighted and I'm stunned to say that it worked.
It'll be interesting to hear what they come back with.
Thanks again

How to configure the router using Expand box?

I need help on configuring the Cisco routers.
Here's the scenario...
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. Please see attached network diagram setup. All Expand appliances are already configured. Thanks.
What configuration should be in GW1 and R2, both C2851?

Hi Daniel,
I configure it as PBR so that all www traffic will be pass to that tunnel. I want all www traffic from Area 1 to Area 2 (vice versa) will pass to IPComp Tunnel (see diagram below). I configure a policy based routing in each router. Did I miss something in router configuration? Did I apply the PBR in right interfaces? How can I configure also the returned www traffic in Router 2? I really appreciate for any response. Thank you.
ROUTER 1
interface GigabitEthernet0/0
ip policy route-map EXPAND_AREA1
route-map EXPAND_AREA1 permit 10
description IPCOM TUNNEL TO AREA2
match ip address EXPAND_ACL
set ip next-hop A.A.A.2
ip access-list extended EXPAND_ACL
remark PACKETS THAT PASSES TO IPC TUNNEL
permit tcp any any eq www
========================================
ROUTER 2
interface GigabitEthernet0/0
ip policy route-map EXPAND_AREA2
route-map EXPAND_AREA2 permit 10
description IPCOM TUNNEL TO AREA1
match ip address EXPAND_ACL
set ip next-hop D.D.D.2
ip access-list extended EXPAND_ACL
remark PACKETS THAT PASSES TO IPC TUNNEL
permit tcp any any eq www

How to configure WRT54GL as router only?

I already have a linux server doing all the routing for my internet connection. I just wanted to add Wireless access for wireless devices i just bought. So, i want to configure this wrt54gl only as wireless router.
So, I configure this wrt54gl as router mode. I connected this port 1 wrt54gl into my existing wired switch. I configure the wrt54gl to account lan IPs of 192.168.10.200 to 250. When I try to connect my wireless notebook, it can connect and get the IP. But problem is the notebook get gateway of wrt54gl. How can I make this wrt54gl to give out my real gateway, 192.168.10.1???
My linux server is the real gateway with IP 192.168.10.1
WRT54GL ip is 192.168.10.100
Do I need to connect the lan into the internet port instead?

Perhaps this is something to do with Setup --> Advanced Routing --> Static Routing??
I don't know what value to fill up. I tried just now and it caused routing problems. I had to reset the router to factory default and configure the thing again.
Appreciate any feed back.

How to configure router to use ip pool on the aaa server for vpn clients

how to configure router to use ip pool on the aaa server for vpn clients . i want to use vpn clients to connect to the router. authenticate using the aaa server username databse and also use the ip pool cretaed on the aaa server. i am not able to find the command on the router pointing to use the pool created on the aaa server. can u some one help me with this command.
sebastan

Hello Sebastan,
what do you use as AAA server (e.g. ACS with TACACS+ or RADIUS) ?
Regards,
GNT

How to configure users for internal mail routing only in exchange 2013

Hi Guys!
I have a scenario here that i have three (3) group of users, one group is able to have an inbound and outbound mail, meaning they can send and recieved emails from internal and external.The second group of users should have inbound mail(local mail) only
(cannot send and recieved mails from internet), and the third (3) user is they can recieved an outbound mail but they are not allowed to send mail directly to the client,(Ex.
[email protected],[email protected],[email protected]) instead they will use the
[email protected] as the reply to the client. Please let me know how to configure group user 2 and 3.
Thank you.
regards,
Paul

Hi Paul,
Great advice from Maganti, just elaborating steps:
Prevent Group 2 send e-mail to internet by transport rule:
1. Login EAC with administrator, Mail Flow---> Rule, click “Create a new rule, then give a name “Group2 - No Internet Mail”.
2. Conditions: select "From a member of a distribution list" & select group "Group2"
3. Select another condition "Sent to users inside or outside the organization" & Select Outside.
4. Actions: select "send bounce message to sender with enhanced status code" & write your custom message like “You are not authorized to send mails to internet”.
Prevent Group 3 directly send e-mail to internet, however it can send message as group:
We also can create a transport rule which is same with Group2, then open Active Directory Users and Computers to add send as permission with another group (contain same users as group3).
Best Regards,
Allen Wang

How to configure radio in 1812 router as client?

Similar Messages

Maybe you are looking for