How to configure resistor network on BNC-2095 with SCXI-1100

The manuals are not entirely clear on this point. I have a BNC-2095 that is connected to a SCXI-1100, and will be reading voltage input signals from pressure transducers and other assorted sensors. The manual indicates that I should not use a ground-referenced input with the BNC-2095 and have the 10-ohm resistor networks in place, but it only discusses installing the 10-megaohm resistors for use with the SCXI-1102. What is the correct configuration for use with the SCXI-1100?
Thanks,
Tom

Hi Tom,
Using the 10 MOhm resistor network instead of the default 10 Ohm resistor network with the SCXI-1102 allows you to measure both floating and ground-referenced signals. According to page 7, Table 2 of the SCXI-1303 manual, this is not recommended with the SCXI-1100. I will verify with R&D that this is also the case when using the SCXI-1100 with the BNC-2095.
If you are certain that your signal is ground-referenced then you should remove the default 10 Ohm resistor network. The input impedance should be high enough to prevent any sort of ground loop. Check page 5, Table 1 of the BNC-2095 manual for the appropriate jumper settings when measuring ground-referenced signals
IMPORTANT NOTE: Do not attempt to measure a ground-referenced signal with the default 10 Ohm resistor network installed. This is well documented in both the BNC-2095 and the SCXI-1303 manuals that it may cause damage to your hardware.
Rod T.

Similar Messages

[SOLVED]How to configure pptp vpn start on boot with netcfg?

I've configured 2 profiles:
eth0 and ppp0, where ppp0 is a pptp vpn tunnel.
$ ls /etc/network.d/
eth0 examples interfaces ppp0
$ cat /etc/network.d/ppp0
CONNECTION='ppp'
INTERFACE='ppp0'
PEER='dxt'
PPP_TIMEOUT=10
$ cat /etc/conf.d/netcfg
# Enable these netcfg profiles at boot time.
# - prefix an entry with a '@' to background its startup
# - set to 'last' to restore the profiles running at the last shutdown
# - set to 'menu' to present a menu (requires the dialog package)
# Network profiles are found in /etc/network.d
NETWORKS=(eth0 ppp0)
# Specify the name of your wired interface for net-auto-wired
WIRED_INTERFACE="eth0"
# Specify the name of your wireless interface for net-auto-wireless
WIRELESS_INTERFACE="wlan0"
Manually, I can start up ppp0 correctly.
$ sudo netcfg -u ppp0
:: ppp0 up [ BUSY ] Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
CHAP authentication succeeded
MPPE 128-bit stateless compression enabled
Cannot determine ethernet address for proxy ARP
local IP address 10.100.3.132
remote IP address 10.100.3.1
[ DONE ]
$ ip addr list dev ppp0
8: ppp0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1496 qdisc pfifo_fast state UNKNOWN qlen 3
link/ppp
inet 10.100.3.132 peer 10.100.3.1/32 scope global ppp0
But after booting, only eth0 is up. How to configure ppp0 to start on boot with netcfg?
Last edited by rchiang (2012-12-21 01:09:32)

Thanks a lot for your instruction.
netcfg works now!
chris_l wrote:
Did you
systemctl enable [email protected]

How to configure the services(WDA) in ESS with EHP7

Hi Experts,
I have a requirement to configure ESS/MSS in R/3 . fisrt time am going to configure the ESS/MSS in R/3 with EHP7.currently we are using
ECC6.0 EHP7 with SP 2 and portal 7.4 can any one help me out which business functions need to be activate and which components need to activate.
How to configure the service in launch pad with WDA.please guide me the step by step procedure.
Please share the config guide if anyone have.

hi sap scn ,
Tips & Recommendations for customizing ESS Menu (WD ABAP) - ess launchpad
Summary of configuration options in ESS Personal Information scenario -personal information
go to t-code lpd_cust see ROLE ESS and INSTNACE MENU ...Clcik it and copy to Z launchpad and drag and drop the services which u want and use it
if any other revert back again

How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?

hi.
I found How to Configure Transparent caching on Cat 6500 with CSM in routed mode.
But,
I need help How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?
Please let me know sample configuration.
thanks.

Hi,
I wrote the document you mentioned and I also wrote the one below.
http://www.cisco.com/en/US/partner/products/hw/modules/ps2706/products_configuration_example09186a00802c1201.shtml
The one with the SSLM is a bridge mode config.
If you replace the SSLM with a cache [or a farm of caches] it would be a similar config.
Replace the SSL21 vserver with an HTTP vserver [most important is to keep the vlan configured on each vserver]
Regards,
Gilles.

HOW TO CONFIGURE GUEST NETWORK AND LIMITE BANDWIDTH

Dear all,
Please help me how to configure internet access rule and limited the bandwidth for guest network via TMG Forefront 2010.
Thanks you & best regards,
Hung Viet

Hi，
First you can create the new network set which is mapped to guest subnet, after that you can create access rule for this network set.
If you want to control bandwidth, you may need 3-party tool like this:http://www.bsplitter.com/
Best Regards
Quan Gu

How to configure the network on Sun Solaris 8

The Sun workstation is a license server, and Window NT workstation need to access the license file that located in the sun workstation.
Now the Window NT workstation cannot connect with the sun solaris, and I guess that I need to configure the network on Sun Solaris 8.
Could you please tell me how to do that step by step?
If there is the system tool like the window system to configure the network easily and quickly.
I appreciate it.
Mark

If your sun system is working then probably it has network configured already .You can check it by the following command on the sun.
ifconfig -a
Generally applications asks where license server is located and you need to give the ip-address or host name only . Application docs will give more detail about it.
You can get ip-address from ifconfig comand above.
Hemant Sharma
http://www.adminschoice.com

HT4259 how to configure extended network via ethernet

how to configure an extended network via ethernet

I assume that the Express is new, so that it still has the factory default settings.
Connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the AirPort Express
Power up the Extreme and Express if they are not already powered up
Open Macintosh HD > Applications > Utiltities > AirPort Utility
Click on the tab in the upper left hand corner of the window that reads Other AirPort Base Stations (1)
Click on the AirPort Express xxxxxx
Wait a minute or two while AirPort Utility analyzes the network and then announces that the Express will be configured to extend your network
Enter a name for the AirPort Express and click Next
Wait 2-3 minutes while AirPort Utility configures the Express and the Express restarts
When you see the message that setup is complete, click Done
That's it.

How to configure cRIO 9004 and link it with Labview?

Today i tried to connect the cRIO 9004 to my pc using the serial cable
but unfortunately the controller was not detecting on my pc. Then I
turned on the IP reset button and tried connecting it using LAN to get
an IP address but it also didn't work. I was looking for drivers on the
internet and NI website but I couldn't find any directly related ones.
Status light is blinking slowly and continuously(one flash every
couple of seconds). According to cRIO 9004 manual it indicates "That the
controller is unconfigured. Use MAX to configure the controller.
Refer to the Measurement & Automation Explorer Help for information
about configuring the controller".
I tried MAX but its still not detecting the controller to configure.
It would be great if you'll could help me out with this as I'm configuring this type of a controller for the first time.
Thanks and regards
Kavin

Hey,
First of all get sure that you have LV RT and FPGA as well as the NI RIO driver installed at your system.
Then the easiest way would be to use a crossover ethernet cable to directly connect the cRIO to your PC.
Give the PC a static IP Adress e.g. 100.100.100.100. Deactivate Firewall and Virus Scanners.
Reboot the cRIO with IP Reset Switch ON, then it should appear in MAX under Network Devices with IP 0.0.0.0.
Give the cRIO also a static IP like 100.100.100.111, set IP Reset switch to OFF before saving this settings.
Now you can install the software at your cRIO also via MAX.
Then you should be able to find it in LabVIEW by right-clicking "Project UntitledX" and "Add Targets and Devices".
There should be different tutorials online how to configure a cRIO or other Realtime targets.
Christian

How to Configure Transparent caching on Cat 6500 with CSM in routed mode

I am trying to configure Transparent caching on Cat 6500 with CSM in routed mode, but facing some problems in it , also I have gone thru the example config on cisco site for transparent caching using CSM on Cat 6500 , but the above does not fit my clients requirement.
The scenario is like
Access Switches - Cat6500 with MSFC & CSM - Internet Router
|
Cache Engines and Real servers
The clients as well as real servers are on seperate VLANs (L3) and the requirement is to load balance the internet traffic using cache engines.
I'd really appreciate any helpful suggestions or any useful links/docs/info on this.
Thanks
kumar

Hello Joerg,
Thanks for the reply.
I have already gone thru the sample config shown by this weblink, however this link refers to configuring transparent caching on the CSM in BRIDGED MODE ( i.e both the client and server vlans are having the same IP address ) but in our case , we have multiple L3 VLANS on the CAT6509 having IP addresses in different SUBNETS , and the Real servers to be used for caching also exist on one of these VLANS. Thus, the scenario described by the Weblink does not apply here. Also , in the configuration referred by the above weblink, the VLAN 100 is configured as client , however the endusers are shown to be on vlan200 which is configured as SERVER VLAN in the CSM.
Dont you think there is something wrong here, I mean the endusers should be on VLAN 100 (Client) and real servers on VLAN 200 (SERVER).
So, I have to configure CSM in routed mode ( i.e both the client and server vlans will have seperate IP addresses in different subnets ) and the endusers will be on all VLANS .
Pls let me know , how I can implement this solution.
Thanks again
Sudhir

How to configure home network with Airport Extreme + D-Link DIR-665

*hello everyone,*
*I had these two working fine together until the D-Link took a dump the other day. No explanation. Just stopped working until I reconfigured everything.*
*Which then led to my Airport Extreme being unable to connect to the network at all, much less the internet...*
*My home network is set up like this:*
*Optimum Cable*
*Motorola Surfboard modem --> D-Link DIR-655 (via ethernet)*
*- Provides wifi and ethernet connections on one side of my house*
*DIR-655 --> Airport Extreme (via ethernet run to other side of house)*
*- Provides wifi and ethernet connections on the other side of my house*
*My MBP won't connect to anything other than my AE running N, so I have that set up primarily for my MBP over wifi, while feeding an ethernet connection to a Netgear router running B/G, for my iPhone and other devices.*
**So here are the relative details:**
*I decided to start fresh and do a factory default configuration with my Airport Extreme. My working system from earlier was essentially it's own wifi network, but the airport utility 'insists' that I need to run my AE in bridge mode. I've tried that, but I can't get online. I can see my shared connections, so something's getting through, but I cannot connect to them, in addition to being unable to get online.*
*I'm not really sure how to best illustrate this problem, so I've ran through the process again and jotted down a few notes. Excuse the rambling nature of my narrative, this is a 'blow by blow' account of the Airport Utility setup process:*
Airport version 7.4.2
IP address 192.168.0.192
router address: 192.168.0.2
Configuring over Airport connection.
- I want AE to join my current network
-.. connect AE to my network using ethernet to extend or create second network
- select device AE will connect to using ethernet - DIR-655 network (displayed w/ airport icon?)
- create an additional network (through ethernet)
AE updates..
- problem 1 of 1 : unsecured wireless network
wpa wpa2
Bridge mode or share a single IP address using DHCP
selected bridge mode
results: AE has green light, airport utility is satisfied but no connection to network is possible. Shared connections are visible, but unable to access
next try:
manual setup
Wireless mode: create wireless network
radio mode: 802.11n only (5 GHz)
channel: auto
wireless security: WPA2 personal
(bridge mode still active)
(this is the exact setup that worked for years before..)
updated…
AE light is green, but no connection to internet or shared connections (though visible)
back to airport utility
manual setup:
internet menu:
connection sharing: share a public IP address
update
--> 2 problems
DHCP Beginning address: 192.168.0.2
DHCP Ending Address: 192.168.0.2
chose 'assist me'
(now one shared connection to Mac Mini becomes active? Had selected it earlier. Able to browse folders, but not share screen)
AE refreshed now with amber light, with reported problems
Problem 1 of 2: Internet Connection
Your Apple Wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network… etc
- changed IP address to match router IP address (?) Utility goes on to next problem
Problem 2 of 2: Conflicting DHCP Range
This Apple wireless device rejected a DHCP address in the same subnet as its internal DHCP server. You should probably switch your Apple wireless device to be in bridge mode. If you still want to be using DHCP and NAT to share a single IP address, you should change your DHCP range.
- maintain selection: share a single IP address using DHCP and NAT (utility forces you to: ignore; skip; or select bridge mode - which doesn't work..)
- chose 'skip' for problem 2
- updated AE..
New problem:
Problem 1 of 1: Double NAT
This Apple wireless device has a private IP address on its Ethernet WAN port. It is connected to a device or network that is using Network Address Translation (NAT) to provide private IP addresses. you should change you Apple wireless device from using DHCP and NAT to bridge mode.
- selected Bridge Mode
updated AE…
"Setup Complete!"
Unable to connect.
** At this point, I am still able to see my shared connections, and while iTunes is open, I can play my shared library that is on my Mac Pro, which connected to the DIR-665 via ethernet, through yet another D-Link router (DIR-615)! I am still connected to the Airport Extreme via wireless, so the system is working, to an extent.*
*So I'm not sure what to do. How can I remedy my IP address issue? Bridge mode doesn't work (as far as I've experienced), so I'm struggling with my DHCP settings..*
*Thanks to anyone who has any suggestions!*

Hi Preston,
I would recommend not starting the numbering scheme for the IP addresses using a '0'. Yes the range is 0-255, but some numbers are reserved, and not generally good practice.
Also, assuming you have reset all factory defaults, start anew and have the modem --> router using NAT for dynamic IP addresses --> (other side of the house) Airport Extreme --> not a NAT configuration, but you need a simple switch. Do not use the NAT capabilities on this one. Maybe, just maybe the computer will work now. This will eliminate your double NAT and also help (hopefully) with the D-Link.
Sorry I cannot help more, I do not own any of the products you talk about, however I have networking experience. Hope it helps.
--Morris

How to configure a Network Interface?

Hey guys.
I'm very new to Solaris OS. I've now installed Solaris Express Developer Edition on my Laptop. After the restart of the installation,I find out, that my network don't work. I try to configure it with the network-admin-tool, but i can't add something, because the button "add" is nowhere in the window.
Is it possible, that Solaris don't detect the interface and how can I see it?
Thanks and sorry for the bad english :).

Look for *e[0-9] (as nge0, nge1, bge0, le0, etc.) in:
# dmesg | less
or:
# less /var/adm/messages
Exaple:
Oct 13 15:54:45 hostname nge: [ID 223987 kern.info] NOTICE: nge0: link up 100Mbps Full-Duplex
"Unplumbed" interfaces maight not show up in the kernel log as they are passive. To "plumb" all supported interfaces:
# ifconfig -a plumb
# ifconfig -a
(MS' ipconfig mimics ifconfig :o)
If it lists say 'nge0' and you don't have /etc/hostname.nge0 then:
# cat /etc/hostname.nge0
cat: /etc/hostname.nge0: No such file or directory
# uname -n > /etc/hostname.nge0
(or # echo nge0 > /etc/hostname.nge0)
Add the address to /etc/hosts and the netmask to /etc/netmasks and the defaultgateway to /etc/defaultrouter
Example:
/etc/hosts:
10.0.0.1 gw.fqdn gw
10.0.0.2 hostname.fqdn hostname nge0
/etc/netmasks:
10.0.0.0 255.255.255.0
/etc/defaulrouter:
gw
You can change things on the fly with the comands ifconfig and route, but these files must be edited for a persistent boot configuration.
You can list the entire PCI-tree with:
# prtpicl -v | less
Example:
:model Bridge device
:compatible (a2000003daTBL)
| pci10de,373.1462.7250.a2 |
| pci10de,373.1462.7250 |
| pci1462,7250 |
| pci10de,373.a2 |
| pci10de,373 |
| pciclass,068000 |
| pciclass,0680 |
:driver-name nge
To see if your interface has a driver look for the PCI to driver-mapping in /etc/driver_aliases. Also check http://www.sun.com/bigadmin/hcl/ and http://www.sun.com/bigadmin/hcl/hcts/install_check.html
(put /sbin and /usr/sbin in PATH, i.e. PATH=$PATH:/sbin:/usr/sbin;export PATH)
(use "more" if you don't have "less")

How to configure backup network in Network Load Balancing?

Some time ago I failed to find proper discription, how backup Network should be configured in NLB, because it seems to be too many options here. I´m having troubles in MBAM, its IIS autherization failing with error code 401 when dedicated FQDN adress is
used which points to NLB cluster. More information about my MBAM problem is here:
https://social.microsoft.com/Forums/en-US/a0dbe7d9-6440-42f2-99e1-21563647764f/mbam-25-installation-on-2-web-servers-as-ha-with-nlb-an-error-has-occurred-on-helpdesk-website?forum=mdopmbam
Now I need to know, what is the proper way to configure NIC and TCP/IP in NLB hosts. As I see it, there are few options but which one is the one?
1. On hosts, 1st NIC is with domain IPs, 2nd NIC is direct IP to another´s host 2nd NIC. This is the way how it should be done in Fail-Over Cluster, but this method does not seem to work witn NLB at all. Cluster adress does not respond.
2. On hosts, 1st and 2nd NIC is configured both to domain Network, same subnet. 2nd nic does not have default gateway. This method works somehow, but displays error in NLB console, when cluster is created.
3. On hosts, there is only one NIC to domain Network and no backup Network at all. This probably requires multicast mode? In MBAM HA documentation, NLB is discribed as unicast.
Hosts, meaning nodes, are 2012 R2 and located on Hyper-V 2012 R2. MAC spoofing is enabled.
- An additional side question - is it true, that NLB feature is not so reliable, and non-Microsoft hardware NLB is recommended for big companies, or
did I just mess my NLB configuration so bad?

Hi yannara,
When you use NLB cluster node with multiple NIC, you can choose different NLB mode, such as
Single network adapter in unicast mode
A cluster in which ordinary network communication among cluster hosts is not required and in which there is limited dedicated traffic from outside
the cluster subnet to specific cluster hosts.
More detail how to select NLB mode you can refer the following KB:
Clustering Technologies
http://msdn.microsoft.com/zh-cn/library/cc784941(v=ws.10).aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to configure SunCluster 3.1 8/05 with Network File System

Hi Gurus,
does anyone has experience to configure SC3.1 8/05 using nas as cluster filesystems?
I've found this document in docs.sun.com:
Installing and Maintaining Network Appliance Network-Attached Storage Devices in a Sun Cluster Environment
This document explain how to use scnas and scnasdir commands, how to use netapp as quorum device.
It seems incomplete, after I configure netapp in cluster what I need to do to register netapp filesystems in the resource group?
Thx,
Antonio

Please see SUNW.ScalMountPoint
http://docs.sun.com/app/docs/doc/819-2981/6n58037vt?l=fr&a=view&q=network+appliance+file+system+ressource+group
Regards,
Laurent

How to configure the network and access to the Extender

I have the Philips Wifi router of Belgacom and le LED of LINK of the Extender stay red. When I use the software on PC, it doesn't find the Extender..
How are parameters to configure router for the Extender can configure it? On my Extender, I can't connect a cable, this is the first model.... Thanks for help

try to reset the extender...
look for its default SSID which is linksysRxxxx on yOur wireless computer then connect to it...
after connecting set staticIP on yOur wireless computer and then try to access the extender frOm there(192.168.1.240)....
hOpe this helps...

How to configure extended network via ethernet

i have a airport extreme and i need to connect my airport express using ethernet cable.
what should be the configs in the airport extreme to get this done?
thank you.
mauro

Please answer my questions on your other post so that we can help.

How to configure resistor network on BNC-2095 with SCXI-1100

Similar Messages

Maybe you are looking for