How to Configure Software iSCSI including Multipath
Oracle Linux 6.6 3.8.13-44.1.1.el6uek.x86_64
Installed with a production network interface card and two 10G network connections for iSCSI traffic only. Both iSCSI cards are on the same vLAN with different IP addresses on a range.
Connecting to a DELL Compellent SAN with 1TB of storage presented to the machine.
Connections can be successfully made via iSCSI and the target can be logged into however in the disk utility window on the server the storage shows as a single 1.1TB multipath drive as dm-0 along with 4 separate connections between sdc and sdf.
The output from multipath -ll is as follows.
I'm guessing that something in the underlying configuration is incorrect and would appreciate any assistance that can be provided.
Hi
I've got 2 10G SFP+ cables attached to the switch each with their own IP address.
eth0 Link encap:Ethernet HWaddr 2C:44:FD:87:60:AC
inet addr:10.160.10.26 Bcast:10.160.10.255 Mask:255.255.255.0
inet6 addr: fe80::2e44:fdff:fe87:60ac/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:35315 errors:0 dropped:0 overruns:0 frame:0
TX packets:698 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3204261 (3.0 MiB) TX bytes:102647 (100.2 KiB)
Interrupt:32
eth1 Link encap:Ethernet HWaddr 2C:44:FD:87:60:AD
inet6 addr: fe80::2e44:fdff:fe87:60ad/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:34534 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3129510 (2.9 MiB) TX bytes:270 (270.0 b)
Interrupt:36
eth2 Link encap:Ethernet HWaddr 2C:44:FD:87:60:AE
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:32
eth3 Link encap:Ethernet HWaddr 2C:44:FD:87:60:AF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:36
eth4 Link encap:Ethernet HWaddr 38:EA:A7:34:09:60
inet addr:10.160.12.46 Bcast:10.160.13.255 Mask:255.255.254.0
inet6 addr: fe80::3aea:a7ff:fe34:960/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30412 errors:0 dropped:0 overruns:0 frame:0
TX packets:36352 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8802884 (8.3 MiB) TX bytes:3280896 (3.1 MiB)
eth5 Link encap:Ethernet HWaddr 38:EA:A7:34:09:61
inet addr:10.160.12.47 Bcast:10.160.13.255 Mask:255.255.254.0
inet6 addr: fe80::3aea:a7ff:fe34:961/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8229 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2150770 (2.0 MiB) TX bytes:704 (704.0 b)
eth0-3 are the production network. eth4 and 5 are the iSCSI network.
Similar Messages
-
How to configure software load balancer for R12.1.3
Dear All,
I need to configure software load-balancer on application tiers and i need to know if its possible to have a software load-balancer in place of hardware load balancer if i need to route the load on two application nodes.
Thanks !As we do not certify, nor support 3rd party loadbalancers we can not confirm that the Piranha loadbalancer will perform as expected with EBS. The basic minimum requirements or loadbalaning is that it has death detection, and session / cookie persistence We also typically require that a hardware loadbalancer is used. Internally we use F5 loadbalancers, and Cisco ACE.
What are the limitations of a software load balancer compared to hardware ? As mentioned above, your software balancer should has the capability of "death detection, and session/cookie persistence" -- More details can be found in (Implementing Load Balancing On Oracle E-Business Suite - Documentation For Specific Load Balancer Hardware [ID 727171.1]).
Oracle Web Cache can be used as a software load balancer (which is an Oracle product), but Oracle recommends you do not use it in production instances.
Thanks,
Hussein -
I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.
Hello, since nobdy else has replied...
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there. -
in dreamweaver mx 2004 and dreamweaver cs4, how I configure, when download/upload do not ask me to include DEPENDED FILES but act without including ?
Open the Preferences panel (Edit menu on Windows, Dreamweaver menu on a Mac), and select the Site category. There are two checkboxes there for dependent files. Make sure both are selected. The Dreamweaver default is NOT to upload/download dependent files. You need to click Yes, if you want the dependent files to be included.
-
I would appreciate your help on how to configure a gmail in a way it ask for the password everytime I connect?. In the only way I can configure it I have to include the pw when configuring the account and after that it do not ask for pw so everyone that shares my iPad can oppen my mail with no pw required.
ThankThe iPad is designed to be a single user device, and there is currently no way to password protect the Mail app - even removing the account password from Settings > Mail, Contacts, Calendars will just prevent new mail being downloaded, it won't hide those that have already been downloaded. There is this work-around for the app : https://discussions.apple.com/message/13127632#13127632 . Also there might be third-party email apps that feature password protecting.
-
How to configure Team explorer 2010 command-line tool in Mac x os.
Hot to configure shell or system path to include the folder to which (TF client) unzipped archive available. I am new to Mac X OS. Please help.Dmitry,
Thanks for the great writeup!
I think I've got my universal instant client libraries built correctly.
I too am using MacBook Pro but I'm getting stuck at building the 32 bit oci8.so
First problem is my pecl download (ver 1.4.1) did not contain a "configure" file so ./configure failed.
I used configure from /sw/....... to try to continue.
Second problem. Using existing configure from /sw/.... I used an appropriate variation of your example command
(./configure --with-oci8=instantclient,/usr/local/oracle/instantclient_10_2 && make).
Things look like everything ran OK but The output does NOT include an oci8.so file
So I guess my question is: Which "configure" should I be using? And if it is not the one on the system under /sw/...
where would I get it since it doesn't come in the pecl download? -
How to check that same Oracle software versions(including patch versions)
How to check that same Oracle software versions(including patch versions) is installed on two hosts(machines) ?
We are using following process:
On Host A :
1) Get the Oracle version using SQLPlus -v
From this output, extract the version number.
2)Find the patches installed using opatch lsinventory -detail
From the output , Extract the Patch numbers and Bugs fixed.
3) Store the version , patch and bugs information in a common file.
On Host B :
Repeat the steps 1 and 2 and compare with the values from Host A.
Please let us know if there is any other method to do this.
Thanks.This is wrong: for Oracle Database version 10.2.0.4 *4* identifies the patch set and does not give information about interim patchs.
It is correct to use opatch lsinventory to get interim patchs.
Edited by: P. Forstmann on Jul 21, 2009 12:38 PM -
How to build an installer including the vision Acquisition Software
hi all, my question is "how to build an installer including the Vision Acquisition Software".
is it enough to select "2010 Run-Time Engine" "Vision Run-Time Engine" and "NI-IMAQdx"? Its ok with the "2010 Run-Time Engine" but there is some problem with the other two.
can some one help thanks a lot!hi again, i have some problem with install Vision Run-Time Engine
must i install RTE with the Serial Number, or i can chose the "install this product for evaluation" to continue the installing, maybe active it later. But after i chosed "install this product for evaluation" and finish the installing, i still cant find RTE from my disk.
i cant even chose my path to install the RTE. Can u plz tell me what is wrong with that? -
How to configure OraMTS to allow WCF using MSDTC access OracleDB On unix?
How to configure OraMTS to allow WCF using distributed transactions to access the ORACLE database On Linux/Unix ?
Env:
1. DB-tier node , ORACLE database (version: 11.2.0.1.0) on Redhat Linux server ;
2. middle-tier node ,Both the client, the MS DTC and Oracle MTS run on the same computer , Win7 x64 OS , installed .Netframework 4.0, ODP.net (ODAC112030), and configure the component services in a distributed transaction;
Has done the configuration:
1. ORACLE database on a Linux server (version: 11.2.0.1.0) has execute oramtsadmin.sql script;
2.ORACLE database on a Linux server (version: 11.2.0.1.0) has execute the following script, Creating an Access Control List (ACL);
BEGIN
-- Create the new ACL, naming it "OraMTSadmin.xml", with a description.
-- This provides the OraMTS administrative user e.g. MTSADMIN user FOO
-- the privilege to connect
DBMS_NETWORK_ACL_ADMIN.CREATE_ACL('OraMTSadmin.xml',
'Allow usage to the UTL network packages',
'ORAMTS', TRUE, 'connect');
-- Now grant privilege to resolve DNS names to the OraMTS administrative user
DBMS_NETWORK_ACL_ADMIN.ADD_PRIVILEGE('OraMTSadmin.xml' ,
'ORAMTS', TRUE,'resolve');
-- Specify which hosts this ACL applies to, in this case we are allowing
-- access to all hosts. if one knew the list of all Windows middle-tier,
-- these could be added one by one.
DBMS_NETWORK_ACL_ADMIN.ASSIGN_ACL('OraMTSadmin.xml','*');
END;
3. ORACLE database on a Linux server has set JOB_QUEUE_PROCESSES = 1000;
4. restart Oralce;
5.Test code as follows :
using System;
using System.Collections.Generic;
using System.Linq;
using System.Text;
using JetSun.Infrastructure;
using Microsoft.VisualStudio.TestTools.UnitTesting;
using JetSun.Infrastructure.ServiceModel;
using JetSun.DataModel.Cis;
using JetSun.TestFramework;
using System.IO;
using System.Data.EntityClient;
using System.Data.Objects;
using ConsoleApplicationTest;
using System.Transactions;
namespace Core.Tests
[TestClass]
public class EfOracleTest
public TestContext TestContext { get; set; }
[TestMethod]
public void GetEntities()
//string cn = "DATA SOURCE=HIS30;DBA PRIVILEGE=SYSDBA;PASSWORD=jetsun;PERSIST SECURITY INFO=True;USER ID=SYS;enlist=true";
string cn = "DATA SOURCE=HIS30;DBA PRIVILEGE=SYSDBA;PASSWORD=mtssys;PERSIST SECURITY INFO=True;USER ID=mtssys;enlist=true";
DbsSetting s = new DbsSetting(Dbs.IP, DbsProvider.Oracle, cn);
Runtime.SetDeploymentDir(TestContext.TestDeploymentDir);
File.Copy("E:\\VSTS\\MedicalHealth\\bin\\Debug\\DataModel.Cis.Oracle.dll", Path.Combine(TestContext.TestDeploymentDir, "DataModel.Cis.Oracle.dll"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.csdl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.csdl"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.ssdl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.ssdl"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.msl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.msl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.csdl", Path.Combine(TestContext.TestDeploymentDir, "Model1.csdl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.ssdl", Path.Combine(TestContext.TestDeploymentDir, "Model1.ssdl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.msl", Path.Combine(TestContext.TestDeploymentDir, "Model1.msl"));
string connectionString = s.ToEdmConnectionString(typeof(EdmEncounter), false);
//// Initialize the EntityConnectionStringBuilder.
//EntityConnectionStringBuilder entityBuilder =
// new EntityConnectionStringBuilder();
////Set the provider name.
//entityBuilder.Provider = s.Provider.Provider;
//// Set the provider-specific connection string.
//entityBuilder.ProviderConnectionString = cn;
//// Set the Metadata location.
//entityBuilder.Metadata = string.Format(@"res://{0}/EdmDiagnose.csdl|res://{0}/EdmDiagnose.ssdl|res://{0}/EdmDiagnose.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//entityBuilder.Metadata = string.Format(@".\Model1.csdl|.\Model1.ssdl|.\Model1.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//connectionString = entityBuilder.ToString();
////using (Entities edm = new Entities(connectionString))
//// foreach (var item in edm.ENCOUNTERs.Take(10))
//// Console.WriteLine("{0}\t{1}", item.ENCOUNTERID, item.DISPLAYNAME);
//entityBuilder.Metadata = string.Format(@"res://*/EdmDiagnose.csdl|.\EdmDiagnose.ssdl|.\EdmDiagnose.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//entityBuilder.Metadata = string.Format(@"res://{0}/", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
connectionString = s.ToEdmConnectionString(typeof(EdmFeeInfo), false);
try
//using (TransactionScope tx = new TransactionScope())
using (TransactionScope scope = new TransactionScope(TransactionScopeOption.Required, new TimeSpan(0, 0, 30)))
//using (var dbcn = s.Provider.CreateConnect(connectionString))
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
//edm.Connection.CheckOpen();
//using (edm.Connection.BeginTransaction())
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
item.Amount = item.Amount * -1;
edm.SaveChanges();
// using (EdmFeeInfo edm2 = new EdmFeeInfo(connectionString))
// edm2.Connection.CheckOpen();
// edm2.Connection.EnlistTransaction(Transaction.Current);
// foreach (var item in edm2.FeeInfos.Take(100))
// item.Amount = item.Amount * -1;
// edm2.SaveChanges();
// throw new NotImplementedException();
TestContext.WriteLine("-----------1---------------");
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
throw new NotImplementedException();
catch (Exception ex)
TestContext.WriteLine((ex.InnerException ?? ex).Message);
TestContext.WriteLine("-------------2-------------");
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
6. the test results are as follows:
4 125
4 835.45
4 3458
4 2350
4 200
4 100
4 300
4 123
4 234
无法列入分布式事务处理 （Could not be included in the Distributed Transaction）
-------------2-------------
4 125
4 835.45
4 3458
4 2350
4 200
4 100
4 300
4 123
The main error message:无法列入分布式事务处理 （Could not be included in the Distributed Transaction） , not use distributed transaction everything is normal.
My test environment MS DTC and Oracle MTS Recovery Service run on the same computer, but OracleMTSRecoveryService registry values under£º HKEY_LOCAL_MACHINE \ SOFTWARE \ Wow6432Node \ ORACLE \ OracleMTSRecoveryService ,not under HKEY_LOCAL_MACHINE \ SOFTWARE \ ORACLE,I do not know that there is no relationship.
Is not configured incorrectly?Who can help me, thank you very much!Do you really have a requirement to push data from Oracle to Access rather than pulling data from Oracle to Access? It would be exceptionally unusual to push data from Oracle to Access.
Pushing from Oracle to Access would means that you want some Oracle process running that is updating Access. But you said that your Access database was on your "local desktop" which implies that it is not running on a server where it is always available. So that means that the Oracle process is going to regularly encounter (and report) errors because the Access database is not available. In turn, that's going to mean that your push process is either going to cause the underlying transaction to fail or it's going to mean that the push process is going to have to implement a fair amount of code to queue data to be pushed at a later date (and track all those changes) which is no small task. None of that seems particularly pleasant.
On the other hand, Access is designed to pull data from real relational databases like Oracle. That's the far more normal approach architecturally. It doesn't require an Oracle process, it doesn't generate errors on the Oracle database when the local desktop is down, etc.
And, of course, I'm assuming that introducing Access is even architecturally reasonable. Most organizations would be extremely hesitant to allow data from an Oracle database to get moved into Access because that quickly means that they lose control of the data from a security standpoint, that there are now multiple copies of the data floating around when changes & corrections are made, etc. That causes all sorts of headaches normally above and beyond the headaches that pushing from Oracle to Access would create.
Justin -
How to configure 3Com 3C905C-TX-M...
Hi Everybody,
I am Install the driver software (Solaris8.exe) Solaris support OS from 3Com.com in floppy and now want to configure on Solaris8 x86 plateform. When I am trying like press F4 to add-new device then he need diskket when i put this floppy he told me this is not a valid software I don't know what's happenning with my system. If anybody have other way so please tell me.
My card detail is:- 3Com 3C905C-TX-M EtherLink 10/100 PCI.
Please tell the way how to configure and If any have this driver software provide me...
Thank to all
TanvirSCSA"Solaris8.exe" is probably a windows self-extracting zip archive, or something like that.
So you probably have to find a windows box, and run / unpack it there. Stupid.
OTOH, there's a also a Sun supplied Solaris 8 patch for the original "elxl" driver, it should add support for
the 3c905c-tx-m card:
http://sunsolve6.sun.com/search/document.do?assetkey=1-21-109867-04-1
http://sunsolve6.sun.com/search/document.do?assetkey=1-21-109866-05-1
For a fresh install, you need the 109867-04 patch, it should include an image of an "ITU" driver update floppy,
that can be used by the DCA (F4 - add new device driver). -
I want to set up the Time Machine and I would love to use the Time
Capsule but since I already have a wireless router I need suggestions on
what other
external disks Apple could recommend to use with the Time Machine and
how to configure that disk.
A complication that I need to resolve is the fact that I am using Vmware
Fusion to be able to use Windows on my Mac. Now it seems that Time
Machine is not backing up my files
on that virtual Windows without additional configuration and my question
is whether you can advise me here or whether this is only a matter for
the Fusion virtual machine.If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it. -
How to configure the web interface of service desk
Hi All,
We are currently doing a configuration on solman service desk. I am on a stage where in i need to use the web interface of service desk via tcode notif_create_bsp. However, every time i call the transaction code (call the url) i cant view the web. Only an error the "Network Access Message: The website cannot be found".
I already activate needed services and already publish
SIAC_PUBLISH_ALL_INT but it still doesnt work.
I might have missed some configs/procedure on how to do it correctly.
My questions are.
1. How am i going to know the qualified domain name
of the Web AS for solman? How to configure it?
2. Can anyone give me some guide and any step by step documentation/procedure on this.
You help/suggestion will be very much appreciated
Thank you very much,
IceHi,
+"Check the following 2 things. See if the port 8000 is open and in the url for the BSP in internet explorer, replace the host name with the IP address of your Solman server.+
+"+
That was a helpful tip. I change the host name with the ip address ofour solman server. However, upon login, it promts me to enter username and password. I've tried to login using my solman password but it shows an error like this.
Business Server Page (BSP) error
What happened?
Calling the BSP page was terminated due to an error.
SAP Note
The following error text was processed in the system:
Die URL enthält keine vollständige Domainangabe (10.123.161.125 statt 10.123.161.125.).
Exception Class CX_FQDN
Error Name
Program CX_FQDN=======================CP
Include CX_FQDN=======================CM002
ABAP Class CX_FQDN
Method CHECK
Line 10
Long text -
Error type: Exception
Your SAP Business Server Pages Team
Is there anything i need to configure so that i can maintan the username and password?
Thank you for your assistance,
Ice -
How to Configure Multiple Relays / Mail Gateways
Platform: Sun Solaris 8
Software: iMS 5.2
How to Configure two MX ( relay / Gateway servers) records in imta config file..? Our requiorement is to have two gateways defined ..for example "xyz.net" and "xyz.com". All emails destined to email addresses ending with ".net" should use the "xyz.net" gateway and rest of them should use the "xyz.com" gateway. and the configuration should be flexible enopugh to accomodate future additions to our gateways.
An Early Response would be appriciated.
Thanks
Arun AddepalliWell, To point the outside mail servers to your gateways just put MX entries for each domain into DNS and point dns to the correct host for that domain.
To make the mail server recognize the domain just create it in the ida and put the users under that domain. The users mailhost attribute will take care of letting the gateways know where to forward the mail so it will go to the correct host.
If you need to do domain aliasing with the same users for both domains that is a bit different. Do you need to do this? -
How to configure trex name server
hi all
while creating index i am getting the error
Index could not be created; creating index failed: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
for the above error i need to configure the trex name server using TREX Configuration in the J2EE Engine in j2ee visual administrator .
can any one tell me the clear path that where to configure the above and where j2ee visual administrator installed how to configure the name server
awaiting for replies
regards
ganeshHi Ganesh,
In order to access the Visual Administrator, go to Start > Programs > SAP J2EE Engine > Visual Administrator. After you login, you will see 2 nodes i.e. Dispatcher and Server. Expand the Server node. Then go to "Services" and expand it. Then go all the way down to "TREX Service". Then on the right hand side, go to the property "nameserver.address" where you will key in "tcpip://<nameserver>:<port>". Then hit "Update" and click on the "Save" button. Then when you go to TRex Monitor, you should be able to see the Name Server running. Hope this helps.
Thanks,
Sri
P.S Please rewards points if you find this helpful. Thanks. -
How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module
hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 FGL1618119E
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
R2921-8CPITR-1#Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end
Maybe you are looking for
-
My iPod is charging but it is not recognized by my computer.
I am a new iPod user and I am trying to put music on my iPod. When I connect it to to my computer the charging icon appears but neither my computer or iTunes recognizes it. When I go to Edit and Preferences in iTunes it says no iPod connected but I k
-
Itunes installs ok but doesn't scroll properly. plz help!
Ive installed itunes so many times, it doesn't scroll properly and i cant see the file, edit, view etc..(the bar at the top). I cant get a clear view of all my music and its driving me mental!! Does any1 kno wots wrong?
-
How to used BAPI_SALESORDER_CHANGE to add items
Hi, I am trying to use the above bapi to add items to a sales order, but I can't get the qty to map across. I had the same problem using the create bapi whcih I resolved by populating the schedule tables, but in change this just causes an "unhandled
-
When my phone rings my computer rings. how do i stop it?
How do i 'unlink' my phone from my computer. this new feature is very annoying.
-
Invalid Syntax error while using Ant and WLST
I am trying to run the following code in an ant build file but continue to see the error below even though the exact same code works through the WLST console. Any help would be greatly appreciated. Note: * = 1 tab <wlst debug="true" failonerror="fals