How to configure your PC as a SUN Blade 1000 serial Console

Does anybody have the experience to configure your PC as a Sun Serial Console? What pinout will need for a DB25M/DB9F serial cable? What terminal software you recommend?
Thanks!

It appears that the EDID information is not passing back from that Samsung LCD monitor.
That could be due to a missing wire in the dongle you purchased.
It may mean you need to battle through this in a more manual fashion.
That would explain the Creator card listing Sun's historic default 1152-mode
as the only viable screen resolution for the card (no asterisk on that line).
The man pages for the FFBCONFIG utility,
http://bama.ua.edu/cgi-bin/man-cgi?ffbconfig+1M
suggest you have the -prconf as well as the -propt command switches.
What results do you see with -prconf ?
Compare your results with the example in the man pages.
If no information for the monitor, then that might confirm the lack of EDID signalling.
You could also try using the svga setting instead of the numerical 1024x768x60 resolution.
Also consider using a CRT monitor to do all this investigation,
and only fighting with the LCD afterwards.
... and the output from PRINTENV is ??
We need to confirm that the system is indeed set to display to the screen.

Similar Messages

  • Problem in installing solaris 10 in sun blade 1000

    Dear all,
    I am trying to install solaris 10 in sun blade 1000 and getting a problem that disk doesn't exist ......... After several tentatives, I understood that I need to format a harddrive as it is new. I formeted it with boot cdrom -s and the problem still persists.
    I bought a 73g HDD and the machine recognize it as 68,38g .. is there any upgrade I need to perform for it
    Could someone please help me to solve this problem
    Thanks a lot for your help and reply ...

    I have the same problem ..ubuntu installs fine
    TIA
    Dale

  • Reset sun blade 1000 firmware password

    I tried resetting firmware password successfully on sun blade 100 ;
    By removing the nvram chip and got the ok prompt
    later "set-defaults" ; ""setenv security-mode none" commands succesfully
    removed the firmware password on sun blade 100
    But when I tried the same on sun blade 1000 ; its accepting the new "senenv security-mode none" and confirming back. while I reboot the system its again asking for the firmware password. Tried resetting jumpers; No help.
    Could some of you help me in fixing this issue.
    Thanks in advance.
    -/Raja G

    Hello,
    I tried resetting firmware password successfully on sun blade 100 ;
    By removing the nvram chip and got the ok prompt
    later "set-defaults" ; ""setenv security-mode none" commands succesfully removed the firmware password on sun blade 100
    Don't tell fairy tales ! Without the NVRAM, your setting can't be stored. If you start without the NVRAM chip, then while the system is still powered on, re-inserted the NVRAM and finally used setenv security-mode none, this might work.
    The Blade 1000 has a switch that prevents operation without a closed side-panel. If you close this switch with a piece of paper, the above procedure might work too.
    In case the security-mode ist just set to command and the boot-device doesn't contain the WWN, it might be possible to use a disk with a known root password and a file /reconfigure.
    The only fix without risking to damage the system, is to order a new IDPROM (SEEPROM).
    Michael
    Fixed wrong path for reconfigure file
    Message was edited by:
    MAALATFT

  • How to configure informix connection pool in sun-one appserver 7

    Hello,
    Anybody knows , How to configure informix connection pool properties in sun-one appserver 7?
    Thanks in advance.

    Actually,it couldn't get some advice in here.But now,I known how to configure it,I expended 2 days to search and test it.Follow :
    jdbc class:com.informix.jdbcx.IfxDataSource
    serverName=(INFORMIXSERVER)
    portNumber=1526(default)
    IfxIFXHOST=(host ip)
    databaseName=(your dbname)
    user=(your username)
    password=(your pwd)
    attention:configure right transaction and userthreads in your informix sever
    Hope helpful to someone!

  • How to configure oracle thin drivers for SUN APPLICATION SERVER

    hi all,
    I am working with EJB with oracle as back-end. I wants to know how to configure oracle thin drivers for the SUN APPLICATION SERVER. Please explain me breifly.
    Advanced thanks to all the replies.
    with regards,
    /kumaraswamy.n

    Kumaraswamy,
    Did you try searching the Internet? Here are the results of my Internet search:
    http://tinyurl.com/zo4gk
    And one of the first hits in the list was this:
    Deploying to a Sun Java System Application Server
    Good Luck,
    Avi.

  • How to configure your Outlook GMail account ?

    how to setup gmail in outlook

    Hi,
    Basically we have two choices when configuring a Gmail account in Outlook: POP or IMAP.
    If you want to download the emails from the server to local and don't need local actions to be reflected to the server, POP is your choice. If you want to keep everything on local and on server synchronized, let's use IMAP.
    We can learn How to setup an Internet email account in Outlook 2013 from this kb below:
    http://support.microsoft.com/kb/2758902/en-us
    If you are using another verson of Outlook, there are also information for other versions of Outlook in the kb.
    You need to contact the Gmail support to get the detailed settings for a Gmail account.
    Regards,
    Melon Chen
    TechNet Community Support
    It's recommended to download and install
    Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
    programs.

  • How to Configure the Eterprise Manager in sun solaris

    Hi
    Please help me In configuring the enterprise manager
    my environment :
    2 node RAC in SUN Solaris 9
    database :Oracle 10.1.4.0
    if any body have documents regarding configuring(order wise steps) for configuring Enterprise Manager

    The Oracle docs should help (Oracle® Enterprise Manager Advanced Configuration).

  • How to see your photostream pictures after it reached 1000, how to see your photostream pictures after it reached 1000

    I can't see my old photostream pictures

    Hi can you please help me to hide my ip of skype for everyone as much unprecedented by a game common mn skype and skype ip and they ddose me reslove mn I ask you HELP Michael Delaney

  • Solaris 10 will not install on a Sun Blade 1000

    I have downloaded both the dvd and CD versions of solaris 10, successfully compiling the images of course for the DVD and making
    ISO disks for the CD's.
    They will boot fine, right up to the point I get a X session, Solaris begins installing then cores and gives me a standard terminal window.
    I have updated the open boot prom to the latest version, still with no success.. anyone seen this before ?? HELP, PLEASE :-)

    Well I will be just corn-holed !!!!
    It appears the download version of Solaris 10 is for
    single processor platforms, I was trying to install
    it on a dual processor platform. There is no such thing as a single processor version of Solaris 10.
    No version of Solaris that I'm aware of had any technical (as opposed to licensing) restrictions on the number of CPUs. And if they did, they would spit out a message to that effect, not just crash.
    After removing the
    second CPU, it install flawlessly now. Just kick me
    in the pants :-)I would assume a hardware issue then.
    Darren

  • How to configure network with just 1 ethernet adapter?

    I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Is it mandatory to have more than 1 network card to configure multiple ports? If not, what are the options available to deploy a Virtual Machine that can have applications which are available over the network. I don't have a separate network i.e. public network as well as management network is of same IP range.
    I am having 2 node cluster using NFS for pools as well as repository.
    ~Yagnesh

    yagneshg wrote:
    I was looking for a guide which would talk about how to configure your network in case if you have only 1 Ethernet adapter. Just enable the "Virtual Machine" role on the Management network that is automatically connected. You will then be able to add guest vNICs to the same network.
    I am having 2 node cluster using NFS for pools as well as repository. I strongly recommend you get at least one more physical NIC for your server, if not two: running NFS and the cluster heartbeat and the guest traffic all over the same network is going to put a lot of data down the wire and you may land up in a situation where the cluster traffic is overwhelmed and a node reboots. You need to be very careful in this situation. Network cards are cheap and you should have at least two or three, I reckon.

  • How to configure my vsnl email id

    I am not able to comfigure my email I'd vsnl

    MissMBA, Welcome to the discussion area!
    How does you question have anything to do with OS 10.4's Mail application?
    Are you perhaps asking how to configure your Blackberry to use your .Mac account for sending? If so, the proper place for that question is the .Mac > .Mac Email On Your Desktop discussion group.
    Your outgoing settings should be something like this:
    outgoing mail server: smtp.mac.com
    login: YourDotMacName (without the @mac.com)
    password: YourDotMacPassword
    security: StartTLS

  • Don't know how to configure wireless card for internet

    hi i just move to a new place, and i do not know how to set up my mac for wireless connection. i was given the basic information for the internet to work, and it works for my pc but not on mac. i was given
    Network Name (ESS-ID or SSID)
    WEP Key Type (Encryption type)
    WEP Key Format
    WEP Key
    where do i go to fill in these info for internet?
    please teach me what i m missing for i m not familiar with network. thank u.

    Airport is what Apple's trade name is for 802.11 wireless. If you have wireless in the computer, you have Airport. To see if you have Airport, on your menu bar, go under the  and choose "About This Mac." Click on "More Info." About midway down the list on the left, you'll see "Airport." Click on it. That will tell you whether you are wireless-capable or not.
    If you do not have Airport, you will need to tether up to the router directly using an ethernet cable if you want internet access or else upgrade the computer with an Airport Extreme card.
    If you do have Airport, on your menu bar, go under the  and choose System Preferences > Network >Show: > Airport>. Click on Network. If "locked," click on the padlock (lower left corner) to authenticate. Once authenticated, click on Show: and choose Airport. Click on Advanced (lower right corner). Click on "+" below "Preferred Networks" window. Answer the questions that you are asked, which will cover those four items (SSID and WEP info).
    (Texas Mac Man: that link points to a guide for the Airport Express stand-alone wireless access point using /Applications/Utilities/Airport Utility, not for how to configure your Mac's built-in Airport Extreme card via System Preferences > Network. I could be wrong but I think annie.ryu is wanting information to configure the computer's Airport/Airport Extreme card via Sys Prefs' Network panel)

  • How to make "PCI-IDE SiI0680A pci1095,680 " work  for Blade 1000

    Somebody has reported that making the 0680 chip based PCI-to-IDE card worked on Blade1000.
    http://forums.sun.com/thread.jspa?threadID=5067148&start=15.
    Now I want to expand the storage for Blade1000 by the Adaptec-ASH-1233 which is powered by SiI0680A chip.
    But it does NOT work.
    Any body can help me? Thanks in advance!!!
    The following is the detailed infomation:
    My system env:
    Blade 1000 with solaris 10 U7(5/09).
    I have tried the following (they all dose NOT work):
    1. The card with original bios v3.2.10 (prtconf -pv report class-code: 00018000)
    2. update bios to base bios (none raid, b3308.bin) v3.3.08 (class-code: 00010185)
    3. erase the bios flash (class-code: 00010185)
    ( I think the bios is programed by x86 instruction set , it will not work in sparc.
    by the way, any Solaris(sparc) device driver expert can clear that if the dirver will communication with the card bios?
    If it dose , I think it is imporssible to make it work in sparc system)
    4. Follwing a suggestion from sun HCL and repeat 2 ,3 ( class-code: 00018000)
    add the following nvramrc script in the obp (nvedit)
    0: probe-all install-console banner
    1: cd /pci@8,700000/ide@1
    2: 00018000 " class-code" integer-property
    3: 00000680 " subsystem-id" integer-property
    4: " pci1095,680" " name" string-property
    5: device-end
    Adjust the path on line 1 to reflect your system store with "nvstore", set the "use-nvramrc?" variable to "true" and issue a "reset".
    After a boot the controller will look just as a non-RAID controller.
    The following is the system info:
    with a maxtor 250G disk connected OR a Western Digital 300G disk connected
    <1> prtdiag :
    pci 33 +s/system-board ide-pci1095,680
    okay /pci@8,700000/ide@1
    <2> prtconf -pv :
    Node 0xf00a9874
    assigned-addresses: 81000810.00000000.00000500.00000000.00000008.81
    000814.00000000.00000508.00000000.00000004.81000818.00000000.00000510.00000000.0
    0000008.8100081c.00000000.0000050c.00000000.00000004.81000820.00000000.00000520.
    00000000.00000010.82000824.00000000.0012c000.00000000.00002000.82000830.00000000
    .00180000.00000000.00080000
    reg: 00000800.00000000.00000000.00000000.00000000.01000810.00000000
    .00000000.00000000.00000008.01000814.00000000.00000000.00000000.00000004.0100081
    8.00000000.00000000.00000000.00000008.0100081c.00000000.00000000.00000000.000000
    04.01000820.00000000.00000000.00000000.00000010.02000824.00000000.00000000.00000
    000.00002000.02000830.00000000.00000000.00000000.00080000
    compatible: 'pci1095,680.1095.680.8502' 'pci1095,680.1095.680' '
    pci1095,680' 'pci1095,680.8502' 'pci1095,680' 'pciclass,010185' + 'pciclas
    s,0101'
    name: 'ide' (is raid in my try 1)
    fast-back-to-back:
    devsel-speed: 00000001
    class-code: 00010185 (is 00018000 in my try 1 and 4)
    interrupts: 00000001
    latency-timer: 00000040
    cache-line-size: 00000010
    max-latency: 00000000
    min-grant: 00000000
    subsystem-id: 00000680
    subsystem-vendor-id: 00001095
    revision-id: 00000002
    device-id: 00000680
    vendor-id: 00001095
    <3> prtconf -D :
    ide, instance #1 (driver name: uata)
    dad, instance #0 (driver name: dad)
    <4> /var/adm/messages:
    Jun 6 17:39:51 bird pcisch: [ID 370704 kern.info] PCI-device: ide@1, uata1
    Jun 6 17:39:51 bird genunix: [ID 936769 kern.info] uata1 is /pci@8,700000/ide@1
    Jun 6 17:39:51 bird ebus: [ID 521012 kern.info] gpio_873170 at ebus0: offset 1,
    300600
    Jun 6 17:39:51 bird genunix: [ID 936769 kern.info] gpio_873170 is /pci@8,700000
    /ebus@5/gpio@1,300600
    Jun 6 17:39:51 bird uata: [ID 114370 kern.info] dad0 at uata1
    Jun 6 17:39:51 bird uata: [ID 347839 kern.info] target 0 lun 0
    Jun 6 17:39:51 bird genunix: [ID 936769 kern.info] dad0 is /pci@8,700000/ide@1/
    dad@0,0
    Jun 6 17:39:51 bird pseudo: [ID 129642 kern.info] pseudo-device: trapstat0
    Jun 6 17:39:51 bird genunix: [ID 936769 kern.info] trapstat0 is /pseudo/trapsta
    t@0
    Jun 6 17:39:51 bird cmlb: [ID 107833 kern.warning] WARNING: /pci@8,700000/ide@1/dad@0,0 (dad0):
    Jun 6 17:39:51 bird Corrupt label; wrong magic number
    <5> run any of the following commands will cause the system to reboot:
    # devfsadm
    # ls /devices/pci@8,700000/ide@1/
    # devinfo -i /devices/pci@8,700000/ide@1/dad@0,0
    and give the following messages:
    SUNW-MSG-ID: SUNOS-8000-0G, TYPE: Error, VER: 1, SEVERITY: Major
    EVENT-TIME: 0x4a502cda.0x1dcd9638 (0x30075ddaae0)
    PLATFORM: SUNW,Sun-Blade-1000, CSN: -, HOSTNAME: bird
    SOURCE: SunOS, REV: 5.10 Generic_139555-08
    DESC: Errors have been detected that require a reboot to ensure system
    integrity. See http://www.sun.com/msg/SUNOS-8000-0G for more information.
    AUTO-RESPONSE: Solaris will attempt to save and diagnose the error telemetry
    IMPACT: The system will sync files, save a crash dump if needed, and reboot
    REC-ACTION: Save the error summary below in case telemetry cannot be saved
    if a old Quantum Fireball 20G connected , the following is different with 250G/300G disk connected
    <1> prtconf -D :
    ide, instance #1 (driver name: uata)
    <2> the system NOT report "Corrupt label; wrong magic number"
    <3> And the above three commans in <5> will NOT reboot the system

    detailed message in <5>:
    <5> run any of the following commands will cause the system to reboot:
    # devfsadm
    # ls /devices/pci@8,700000/ide@1/
    # devinfo -i /devices/pci@8,700000/ide@1/dad@0,0
    and give the following messages:
    SUNW-MSG-ID: SUNOS-8000-0G, TYPE: Error, VER: 1, SEVERITY: Major
    EVENT-TIME: 0x4a502cda.0x1dcd9638 (0x30075ddaae0)
    PLATFORM: SUNW,Sun-Blade-1000, CSN: -, HOSTNAME: bird
    SOURCE: SunOS, REV: 5.10 Generic_139555-08
    DESC: Errors have been detected that require a reboot to ensure system
    integrity. See http://www.sun.com/msg/SUNOS-8000-0G for more information.
    AUTO-RESPONSE: Solaris will attempt to save and diagnose the error telemetry
    IMPACT: The system will sync files, save a crash dump if needed, and reboot
    REC-ACTION: Save the error summary below in case telemetry cannot be saved
    panic[cpu0]/thread=2a100eafca0: BERR Error(s)
    000002a100eaea20 SUNW,UltraSPARC-III:cpu_deferred_error+564 (ecc1ecc100000000, 3, 80000000000, 80000000000, 0, 180400000
    000)
    %l0-3: 000007ffef000520 0000000000000001 0000980c00000000 0000080c00000040
    %l4-7: 0000080c00000000 0000000000203000 00000000ecc1ecc1 00000000ecc1ec00
    000002a100eaf190 unix:ktl0+48 (3000289a580, 29ebfa50522, 100, 0, 0, fffd9c00)
    %l0-3: 0000000000000000 0000000000001400 0000009980001607 0000000001262fc4
    %l4-7: 0000000000000003 0000000000000000 0000000000000000 000002a100eaf240
    000002a100eaf2e0 uata:ata_init_controller+374 (30000c21300, 30005871000, 0, 680, 0, 29ebfa4e800)
    %l0-3: 0000029ebfa50520 0000000001873000 0000000000001095 0000000000001095
    %l4-7: 0000000000000000 0000000000000001 00000000704ebf58 0000000000000004
    000002a100eaf3f0 uata:ata_attach+44 (30000c21300, 0, 0, 0, 704e2000, 704e2000)
    %l0-3: 0000000000000000 000000c181659ce0 000002a10001fca0 0000030005485700
    %l4-7: 00000000704e2248 0000000000000000 000002a100eaf4a0 0000000000000001
    000002a100eaf4d0 genunix:devi_attach+ac (30000c21300, 0, 7ffffc00, 3c, 0, 7b798198)
    %l0-3: 00000300000c7438 0000000000000087 00000000018699e8 00000000000036d8
    %l4-7: 00000000018c7400 0000000000000001 0000000000000002 000000000125dc00
    000002a100eaf5a0 genunix:attach_node+9c (30000c21300, 1, 0, 0, 30000c21368, 4)
    %l0-3: 00000000fffeffff 00000000fffefc00 0000000050010000 0000000010000000
    %l4-7: 0000000040010000 0000000000000000 0000000000000000 ffffffffffffffff
    000002a100eaf650 genunix:i_ndi_config_node+104 (30000c21300, 114, 10cda5c, 10, 1869c00, 10cd800)
    %l0-3: 00000300000e76f0 0000000000000001 0000000000000000 0000000000000006
    %l4-7: 0000000001869ca8 0000000000000000 0000000000000000 0000000000000004
    000002a100eaf700 genunix:i_ddi_attachchild+38 (30000c21300, 2a100eafca0, 10000000, 187ba78, 0, 10000000)
    %l0-3: 0000030000c2aaf0 0000000000000001 0000000000000000 0000000000000003
    %l4-7: 0000000001869ca8 0000000001841400 0000000000000000 0000000000000000
    000002a100eaf7b0 genunix:devi_attach_node+84 (30000c21300, 4048, 50000000, 30000c21368, 4048, 10000000)
    %l0-3: 0000030000c2aaf0 0000000000000000 0000000000000001 0000000000000000
    %l4-7: 0000000002000000 0000000050000000 0000000050000000 0000000010000000
    000002a100eaf860 genunix:config_immediate_children+d0 (30000c2aa88, 30000c21300, 87, 8, 4, 18e5280)
    %l0-3: 000000000000003c 0000000000004048 0000000000010000 0000030000c2aaf0
    %l4-7: 00000000003c0000 00000300000a9ac0 0000030000c20cb8 ffffffffffffffff
    000002a100eaf920 genunix:devi_config_common+c0 (30000c2aa88, 4, 87, 87, 0, 4048)
    %l0-3: ffffffffffffffff 000000000180c000 0000000001847a00 0000000000000000
    %l4-7: 00000000018e5280 00000000018e5368 0000000000000009 0000000000000000
    000002a100eaf9d0 genunix:mt_config_thread+60 (30004261dc0, 0, 300023a90c8, 18398b0, 300058b5cc0, 30000c2aa88)
    %l0-3: 0000000000000000 000000c181659ce0 000002a10001fca0 0000030005485700
    %l4-7: 0000000001869940 0000000000000000 000000000004f285 00000000018bfc00
    syncing file systems... 1 1 done
    ereport.io.pci.ma ena=30075d7c00800001 detector=[ version=0 scheme="dev"
    device-path="/pci@8,700000" ] pci-status=2280 pci-command=146 pci-pa=0
    ereport.io.pci.target-ma ena=30075d7c00800001 detector=[ version=0 scheme="dev"
    device-path="/pci@8,700000/ide@1" ] pci-pa=7ffef000520
    ereport.cpu.ultraSPARC-III.berr ena=30075d7c00800001 detector=[ version=1
    scheme="cpu" cpuid=0 cpumask=34 serial="4114C975066" ] afsr=80000000000
    afar-status=1 afar=7ffef000520 pc=1046c54 tl=0 tt=32 privileged=1 multiple=0
    dumping to /dev/dsk/c1t1d0s6, offset 1717895168, content: kernel
    100% done: 26533 pages dumped, compression ratio 3.57, dump succeeded
    rebooting...

  • How to configure Sun Java System Application Server Enterprise Edition 8.1

    hi all,
    How to configure Sun Java System Application Server Enterprise Edition 8.1 to my IDE..( jstudio)
    I have installed jes for my windows system.. so that i have removed platform version of Application Server..
    I try to add the Enterprise application Server (Sun Java System Application Server Enterprise Edition 8.1) to JStudio IDE..
    but i couldn't;

    Configuring your IDE to integrate with Sun App Server is something you probably will have to ask in some sort of JStudio forum. Other than for Netbeans, Eclipse, or possibly IntelliJ IDEA, you might not have much luck answering an IDE question here. I could be wrong though. Maybe somebody will have an answer for you and set me straight.

  • How to configure my 3gs iphone? it says your iphone could not be activated because the activation server is temporarily unavailable...... :(

    how to configure my 3gs iphone? it says your iphone could not be activated because the activation server is temporarily unavailable......
    i live in iran. this 3gs was a gift from america .. it contains NOTHING. i can do nothing with it. it cannot be updated cuz the version is low. i dunno what t do please help.

    Possible causes:
    1. Your antivirus is blocking access to gs.apple.com.
    2. Your phone is jailbroken.
    3. Your computer has been used at some time in the past to jaibreak some iOS device (not necessarily the phone with the problem), and its network database was corrupted by the hacking software that was used.
    4. Apple's activation servers are down (very rare, and never for more than an hour or so).
    5. The phone was reported stolen. If it was it can never be activated again.
    For 1. try disabling your antivirus.
    For 2. & 3. you need to go somewhere other than an apple forum for help. Although you can try deleting lines containing gs.apple.com from your "hosts" file on your computer.

Maybe you are looking for