How to Connect LS CAN (USB-8472) to Single-Wire CAN device?

In the post of http://forums.ni.com/ni/board/message?board.id=30&message.id=216&requireLogin=False , NI Engineer said that
“It is possible to use our Low-Speed CAN boards in
a single-wire mode. However, the board will give CAN warnings. So, the
control program may have to ignore certain CAN warnings.
Randy Solomonson
Application Engineer
National Instruments”
But I can't see the detail connection and software settings in that post.
How can I use LS CAN to communicate with single-wire CAN (such as GMLAN)? Should I make some additional settings in my LabVIEW program?
帖子被hmqi2002在 07-09-2009 04:07 AM
时编辑过了

Similar Messages

How to connect serial or usb or parallel port

telll me how to connect our application with serial port and how to detect weather the usb is connected or not

Without spending too much time looking at the documentation, from using previous similar transducers, the primary two connections you are concerned with are the "+output" and the "ground". The other connections are also important, but aren't directly the concern of the Data Acquisition Hardware. The "+output" produces a variable dc voltage relative to the "ground" input that is a product of the applied pressure, with the maximum output voltage, as shown on the chart, indicating maximum pressure. So you would connect those, through a suitably shielded, moderately short length, wire to the "DAQ" analog input. You will also have to supply the transducer with it's required + supply voltage at pin 2 "vs", and the power supplie's negative to the ground. There are whitepapers on this NI site about connecting to data acquistion hardware and I strongly suggest reading them a couple of times as well as anything online you can find. Writing the DAQ software, in LabVIEW or whatever, can be trivial compared to making the correct, low noise, connections to sensor hardware.
I didn't read how the offset adjustment signal is produced or its use, figure it is designed to allow you to "tune out" some signal offset caused by differences between sensors of a type (they will not all have the same "fullscale output" as indicated in the chart).
As you proceed, please keep asking.
Putnam
Certified LabVIEW Developer
Senior Test Engineer
Currently using LV 6.1-LabVIEW 2012, RT8.5
LabVIEW Champion

How to connect to a usb cam through acrobat api??

I have deveopled a plugin for acrobat...and want to initiate a usb cam through my plugin...is there any method available in the api to detect or connect to a usb cam????If yes please explain how to do so...

...is there any method available in the api to detect or connect to a usb cam????
No. You may look at the apis of your operating system.

How to connect to the USB printer

I connect a USB printer to the USB port of my Airport Extreme. Can someone help advise the procedure for the computers in the network to connect to the USB printer. Thanks!

Unfortunately, not all USB printers are compatible with AirPort base stations. In addition, the AirPort's USB port does not support the "advanced" printer functions, like scanning, copying or faxing, of multi-function printers.
To see if your printer is compatible, take a look at thisiFelix Unofficial AirPort Printer Compatibility link. If your printer isn't listed, it doesn't necessarily mean it won't work, but simply that it has not been verified. iFelix also provides the following workaround for printers not on the list that would certainly be worth a try.
Also you can try this Apple Tech Support article to see if it will help: Printer troubleshooting for AirPort Base Stations and Time Capsule
Finally, check out this IBM support article to see if your printer is listed as having a Postscript or PCL3 interface. If it does, then it will most likely work with the AirPort's USB port. Printers that use the "HP LIDIL" interface must be connected to a computer directly and will not work.

How many connections PAT can handles?

How many connections that an IP address with PAT can support? One IP address with PAT can support 65536 hosts as there are 65536 ports available for an IP(ranging from 0 to 65535)?

Hi,
PAT (overloading) divides the available ports per global IP address into three ranges: "0-511, 512-1023, and 1024-65535". PAT assigns a unique source port for each UDP or TCP session. It will attempt to assign the same port value of the original request, but if the original source port has already been used, it will start scanning from the beginning of the particular port range to find the first available port and will assign it to the conversation.
Please refer the below URL for details:
http://www.cisco.com/en/US/products/ps6640/products_qanda_item0900aecd801ba55a.shtml
I hope it helps.
Regards,
Arul

How to connect from SAP BO Explorer (or) SAP Dashboard to Mobile device ( SAP BO Mobile app)

Hi Friends,
Can you please guide me , how to connect the SAP BO Explorer/Dashboards in mobile device.
Regards,
Mahesh.

Hi Mahesh,
Take a look at this thread.
http://scn.sap.com/community/mobile/businessobjects/blog/2013/10/10/how-to-connect-sap-bo-mobile-to-a-bi-server-40

How to connect an MTN usb rotator to an Apple MacBook Pro 13'3

How do i go about connecting my Apple MacBook Pro 13'3 to the interent with an "Huawei Mobile Broadband E367 HSPA+ USB ROTATOR" on the MTN Network

If your USB port is working now, you didn't damage it and have nothing to worry about.
The behavior you saw in your bus-powered Fujitsu drive is normal for a drive that needs more power than the USB port can provide.
If your USB ports ever do shut down, resetting the SMC may bring them back online again quickly and easily.

How to connect the Wimax Usb stick ,

HI
I have wimaxx usb stick I can not access to internet.softwire not responding .
please help me.
Thank you

According to this page:
http://www.clear.com/support/download/usb/wimax-2-usb-adapter
There is a beta driver for Lion. Beta means a guinea pig application, where you are the guinea pig. So if it doesn't work, you should report to them what's wrong.

How do you set a usb sound card as the default sound device for all programs?

I'm running cmus for a music player and it works fine with the internal speakers on my macbook pro. I'm using a usb sound card for a set of 5.1 surround speakers and cmus won't send it's audio to the usb sound card. I've also tried several other programs for audio and it seems to be hit or miss with being able to use the usb sound card. I'm not sure if I'm overlooking the a setting or if there is a different audio output plugin for cmus that has the functionality I need. Cmus also won't play over any bluetooth audio device while some other sounds will.

Yes I did and it does not appear there. Only the ringtones I have created myself and the default ones appear in the list.
In settings>sounds>ringtone however they all appear

How to connect to PC Companion if applied full encryption to the device?

I have applied full encrytpion to my Z1. Questions is my device is no longer detedted by PC companion even when I need device update. So how to do?

Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
Does your device show up at all in the "My Computer" section of the PC?
What are your thoughts about this forum? Let us know by doing this short survey.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

How To connect More Then One database

How To Connect More the One Database In Single form.
I want to use Access And Oracle In the Same Form.
I want to Transfer data from Access file To oracle database.
Chirag

Hi,
You can do this using EXEC_SQL package. Please see Note 115540.1 on metalink which describes how you can connect to Ms Access and Oracle using EXEC_SQL.
Regards
Kavitha Prakash
Oracle Support

Share NI-CAN Devices to remote desktop session

Hi,
I connect a CAN-device on my local computer. Then I log into a computer via remote desktop and I would like to share my device on that session. How can I use my device on a remote session.
I am using windows 7 on both.

No
The can CAN device is plugged by USB on PC1. I want to share/use it on PC2.
For exemple, i can share a hard-drive, Usb-camera, Serial-port of PC1 to use it on PC2 . I just want to do the same with the CAN-port
I am using remote desktop, is there a way or a better tool to do that ?

How many USB-8472s can I connect to the same computer

I have an application that would require connecting 4 USB-CAN devices to the same computer and control them all through LabWindows. Does the driver facilitate this, or is it a one-at-a-time deal?

No, you can have as many USB CAN devices as you can plug in to your PC. If you use a Hub, don't forget to add a power supply.
DirkW

My iPod Classic is not detected by my Windows 8 computer when I connect it via USB port. How can I get windows to detect this device?

My iPod Classic is not detected by my Windows 8 computer when I connect it via USB port. How can I get windows to detect this device? A message from windows says: the device has malfunctioned.

Try TS1363: iPod: Appears in Windows but not in iTunes.
See also Corrupt iPod classic.
tt2

I am connecting an external USB HDD and I can see it on my Apple Macbook Air. BUT this drive is READ only. How can I write to it?

I am connecting an external USB HDD and I can see it on my Apple Macbook Air. BUT this drive is READ only. How can I write to it?

Drive Partition and Format
1.Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

How to Connect LS CAN (USB-8472) to Single-Wir​e CAN device?

Similar Messages

Maybe you are looking for

How to Connect LS CAN (USB-8472) to Single-Wire CAN device?