How to connect MB battery to +- ?

Basicly all I am looking for where is + - on those golden plated slots? There quite a few of them, I guess for a better connection. I had no luck just randomly trying to find 12 volt +- output. Also why the power supply is 16.5volt and battery just 12volt? Thanks.

Idon't know the voltage and polarity, but I will caution you to be very careful as those LiPo cells can react with fireworks.

Similar Messages

How to increase the battery life of your N series ...

What I am about to post here is valid for any 3G phone or device regardless of model but it is particularly focused towards the N series devices and their power hogging features.
Your battery life is dependant on many many things. How often you take calls on the device, the condition of your battery, the features you use on the device and so on and on. Therefore it is impossible to say that by following the information in this post you will get x amount of days battery life, but it will get you more time out of the battery than you otherwise would have got.
So with that out the way, if your looking to increase your battery life then follow these tips and your battery should start looking a lot healthier.
First of all lets start with THE big one. The one that is going to save you the most juice. Switching 3G off.
Yep, you heard me right. Just by switching the 3G capability of your phone off you will add hours and hours to your battery life. How is this so? Allow me to explain...
Due to the rather poor delivery of 3G in the UK by the network operators, it is rare for any 3G phone to maintain a constant 3G signal. Instead you will find that the phone constantly flips between 3G and GSM mode (Keep an eye on your signal one day). Even those of you on Vodafone who probably have the best 3G network coverage will find this is the case.
Unfortunately, this constant flipping between the two modes sucks power from the battery like a vampire as it alters its reception state for the different modes and the constant flipping is..well...causing it do this constantly! It can sometimes even make your phone unavailable for calls for very brief periods as it trips from GSM to 3G and vice versa.
If you need to use 3G for video calls or whatever then I'm afraid your just going to have to live with this but if you don't (And lets face it few of us do) then you can switch 3G off and increase your battery life considerably.
To do this, go into the "Settings" application (Found in the menu somewhere, by default Nokia normally stick it in "Tools"), and then to the "Phone" tab. In there you will see an option that says "Network mode" and you have a choice of "GSM" or "Dual Mode" (I.e. UMTS and GSM). Set it to GSM and your phone will restart. Once it restarts it will be working in GSM with GPRS speeds only but really for most purposes this is fine.
You have now just extended your battery capability considerably. You can further extend it by going to the "Connection" tab, going into "Packet data" and changing it to "When needed" so it is not constantly checking for a data connection.
The second big change you can make is to turn your phones wifi scanning capability off. The last time I looked not all Nokia's phones that have wifi capability can have their wifi cards switched off entirely but if you can, turn it off except for when you need to use it. Wifi is a power hog.
The next big change you can make is to lower the screen brightness settings on your phone. The less bright your screen is the less power is being used to light it up. Nokia by default leave the screen brightness at something like 50%. Lowering this a bit more will conserve more juice. Before you do this though please consider the fact that lowering the brightness setting will have a big impact on your ability to see the screen clearly in sunny conditions although you will be fine in the dark as you can't lower the brightness that far.
To lower the brightness, go to the settings tool in your phone and into the display option (Hidden in a subcategory called "Personalisation" on the N95). It won't hurt to set the power saving time out to 1 minute and the backlight time out to 10 seconds while your here (Although these are the Nokia default so they should already be set to this).
Finally in regards to the screen, although they may look pretty, animated screensavers use more battery power than the standard blank screen with time and date so avoid them if you can.
It also helps to keep Bluetooth switched off until you need it although the power savings are minimal in comparison to the other changes but every little milliamp counts!
Using the above methods I generally get about 3 to 4 days with about 3 hours talktime on my N95 without using Bluetooth, GPS or anything like that (I might be able to get more but so far I have not paid attention to the battery state before I put it on charge). If I am on a long train journey I can get about 4 hours worth of full screen video and about 2 hours talktime over the period of about 24 hours before it needs a recharge. As I said at the start of the post your mileage will vary greatly depending on how you use your device.
Hope this helps.
Useful links: Phone firmware update | Nokia support site

02-May-200701:14 PM
bixby wrote:
no keffa it is a cop out from nokia
its not unfai as its a premium device with a premium price
the n95 battery is atrocious
dont change the post content as the title is 'How to increase the battery life of your N series device'
your talking about nokia phones specifically
the networks are not to blame
they do not make the handsets : Nokia do !!!!!!!!!!
I'm going to choose my words carefully here...
I would never deny the battery on the N95 is not really up to the job of powering the N95 with its power hungry features. To put the same battery into a phone that has WiFi, GPS and a large 320x240 screen, the same one that goes into the E65 which has comparatively nothing compared to it is a bit pants.
However at no point was I criticising them for the band hopping problem. I labelled the post as how to increase the battery life of your N series device because this is a board for the N series devices. It was a simple choice of wording and not intended to be cutting in any way and I did make a remark that the details would be true of any 3G device at the top of the post.
What I was trying to point out in my second post is that the constant band hopping the phone is being forced to do that is draining its battery so much more quicker than it would if it had a constant signal of one kind or another isn't quite Nokia's fault.
They build it to conform to a laid out specification for 3G. However if the network operators cannot be bothered to roll out their 3G infrastructure adequately enough that the phone can find and remain locked onto a 3G signal that is usable then what are Nokia to do other than offer you the capability to turn 3G off until you need it (Although note to Nokia: That **bleep** reboot the phone does when you do this is entirely unneeded and you know it).
Blaming Nokia for this would be like blaming the manufacturer of your radio for failing to pick up radio because the radio station does not have any transmitters within range of your radio's receiver.
Finally...this band hopping is exhibited by all 3G phones built by Samsung, Nokia, Sony Ericsson, etc, from their most budget 3G model to their priciest piece and is the reason that all phones with 3G capabilities have batteries that do not last for any respectable length of time because these phones are also having to band hop between 3G and GSM.
Finally the proof is in the pudding. Turn 3G off for a few days. See your battery improve. Then (Although admittedly this will be harder to do...mcuh harder) find an area where you get a fairly decent 3G signal constantly. Again, see your battery improve. Try it with a different 3G phone...different manufacturer even. The same will be true.
So I stand by my comment, the network operators and their woeful 3G rollout are the villains costing you a fair chunk of your battery and Nokia cannot be expected to mitigate this....but a better battery would be nice all the same...
Useful links: Phone firmware update | Nokia support site

How to increase your battery health - anyone with similar experiences?

this is my very own self made instruction of "how to increase your battery health"
it is the procedure how i have done it serverall times on my powerbook g4 12".
my stats: 374 cycles, health 86% (3790 of 4400mAh)
age of my mac: 57month (battery bit newer)
**if you to try this: it is on your own risk!**
**this may not be suitable for mac newbies**
**be sure to read this twice before you do it once!**
you will need:
-a pocket lamp or comparable light (to see anything on your sreen when it is dark --> light from the back through apple logo)
-coconutbattery (coconut-flavour.com/coconutbattery) or comparable programm to track your battery information in realtime
-activity monitor
-cool enviroment (to ensure your fans don't have to work that much)
-some time and patience
the intructions:
step1: load your mac until the orange light turns green
step2: disconnect the power adapter
step3: use your mac until 15-25% battery life (track this information in your menu bar)
step4: slow down your activities. the order of the following actions depend on your usage of your mac:
__close programms that use lots of cpu/gpu to ensure the fans slow down to 0rpm (!!)
__turn off everything that needs battery power: airport / bluetooth / speakers / etc.
__eject dvd or cd
__close all programms with important data
__eject idisk / .dmg files in your finder (this is not only a matter of data security)
__dissonnected from peripherals such as ethernet / internet / mouse / keyboard
__use lower brightness level
__open activity monitor to ensure that your hard drive activity is very low, may be you need to close more active programms, close activity monitor when hard drive activity is very low
__open system preferences >> energy saver preferences >> choose longest battery life
when your are ready with those actions go on and ensure you are able to connect to power adapter with your mac quickly (be able to charge - don't do it yet!)
step5: be patient. now it should take some time until your battery level goes down to 3-5%
now there should be no programm running.
do not open any programm now!
do not have a look at your dashboard!
now your mac should be really quiet:
-no fans (0rpm!)
-nearly no hard drive activity!!
-->> if this not the case break go on with step 11&12, try again in a week or two
-->> if you are ready go on with step6
step6: open coconutbattery und use the lowest brightness level
play with your trackpad to ensure your screensaver won't start. waste time until you are at 1-2% battery life.
step7: take your lamp and spot through the transperent apple logo, position your coconut battery window somehow that you can see the current battery charge und the maxium battery charge in the spot of your lamp through the apple logo.
step8: go from the lowest brightness level to the level under the lowest brightness level (a dark screen)
step9: watch your current battery charge carefully und keep on playing with your trackpad to ensure your screensaver won't start.
step10: there is kind of battery buffer made of approximately 1% (once when my "current battery charge" was 3624mAh and this kind of buffer was at 36mAh)
to empty this kind of battery buffer takes much longer as you might expect!
when your current battery charge turns under this kind of battery buffer, your maximum battery charge should change. hopefully it is higher or stays the same. when it is lower now: i'm sorry - i have warned you. may be you have to go through this 'how to' more carefully!?
step11: plug in your power adapter before the battery is cero!
step12: load until the orange light turns green
step13: if it was helpful do not repeat it more than once a week, better once a month
-->webcal://www.apple.com/batteries/images/notebook_icalreminder.ics
(via: http://www.apple.com/batteries/notebooks.html)
anyone with similar experiences about increasing battery health!?
(yes, i'm sorry for my poor english, i've tried my best)

Me too! My battery lasts for 10 minutes. It is awful and I am on my 4th power adapter since they keep breaking too.
From coconut battery: Maximum battery charge 310mah, original 4400, age of mac 45 months, 140 cycles.
From system profile:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 310
Remaining Capacity (mAh): 213
Amperage (mA): -1205
Voltage (mV): 11557
Cycle Count: 140
I went to an apple authorized retailer and they said nothing I can do if it is out of warranty.. is this true?

How charged is the battery?

i have a 500 MB 1st gen shuffle and everything works fine, but i wonder if there's a way of telling how much charge the battery is holding while it's connected to iTunes. i know the battery indicator light has three colors, but can iTunes give any more specific information?

Bummer. Thanks!

How to connect my friends apple notebook through video call

HOW TO CONNECT TO A FRIEND WHO IS USING APPLE NOTEBOOK FROM MY IMAC SUGGEST ME WAITING FOR A SOLUTION FROM APPLE TEAM SUPPORT

Hi,
Typing in all upper case is regarded and shouting here.
Presumably as you have posted in the OS X 10.7.x (Lion) area you are running this version of the OS on your iMac.
This will have iChat 6 on it.
This can use AIM, Jabber and Yahoo IDs within the app.
Apple IDS ending in @mac.com and iCloud issued @me.com and @icloud.com are also Valid AIM Screen Names.
If you use Googlemail and Enable "talk" in the products there you can then use your Google Mail ID as a Jabber ID (although it has it's own Add Account option in iChat)
Facebook has an option to Enable "Chat" which will give you a Chat ID variant on your name there and this can be used in iChat (or Messages) as a Jabber ID.
The Yahoo Account will only do Text chats.
It also has to be an actual ID registered at Yahoo.
Chats are then AIM to AIM or Jabber to Jabber or Yahoo to Yahoo.
So your Buddy will also need a suitable ID or Screen Name for the relevant service.
8:16 pm Sunday; January 19, 2014
 iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

How to connect sound or audio to my tv using hdmi adapter. I tried to connect thru sound settings but my tv is not found.

how to connect sound to my tv set using hdmi adapter. Im using 2009 macbook pro 13". I went to sound settings then output and it shows internal speaker built- in, it wont locate my tv set. pls. help, thanks

You probably can't because it looks like your MacBook Pro is too old to carry audio over HDMI. You will need to run a separate audio cable from the audio out port on the MacBook Pro to the audio in port on the TV.
Check your MacBook Pro model year against the list in this Apple tech note:
About Mini DisplayPort to HDMI adapters
Learn about the Mini DisplayPort in the latest Mac models that enables audio and video output for DisplayPort and HDMI.

I need to know how to connect my macbook to the tv

I ordered the mini dvi adapter for my macbook 13in and obviously it connects to the computer but i have no idea how it connects to the tv. Where does it go? and do i need something else to help connect it to the tv? I am really confused please help.

Yep, Apple makes adaptors to go from the mini DVI on the macbook to almost any type of input that you TV will have. First check the back of your tube to find out what kind of input it has, and order the appropriate adaptor.
Luck
E

How to connect a Sony Bravia TV to the internet through your Airport network

Since it took me a lot of time to figure out how to connect my Sony Bravia TV to the internet through my Airport network, I better share how to do it. Hopefully saving others a lot of time.
My 32EX600 Sony Bravia TV is Ethernet connected to my Mac Mini, which is part of my Airport network, together with another Mac, an Airport Extreme Base Station and an ADSL modem/router. Moreover, the Mac Mini is connected to the TV by HDMI.
Whatever I tried in the TV’s Wired Network Set-up (Auto, or Manual with manual IP, Subnet Mask, Default Gateway and DNS IPs), I couldn’t get it right. Cable Connection and Local Access were mostly OK, Internet Access always Failed.
The solution lies in the Sharing panel of the System Preferences of the Mac Mini. In the Internet Sharing item of that panel, you should choose to “share your internet connection from WiFi to computers (the TV in this case) using Ethernet“, and NOT (as I had chosen before and seemed so obvious) “share your internet connection from Airport to computers using Ethernet“. After that change, the Bravia Network Set-up, using the Wired and Auto options, flawlessly connected to the internet. No expensive (Sony) WiFi USB dongle needed.

I have now had a detailed reply from Sony Europe and the way to do this is to:
1.       Press Home on the TV Setup
2.       Use the right and left arrow to select Setting.
3.       Use the up and down to select Network, press Enter.
4.       Select Network Setup.
5.       Select Wireless setup.
6.       Select Scan
7.       Select your network
8.       A new screen will appear asking for entering the security key.
9.       Enter your WPA2 key.
10.   Select Enter.
11.   It will take you back to the same screen asking for entering the
security key.
12.   Press the right arrow.
13.   Select Auto.
14.   Press the right arrow.
15.   Select Save and connect.
These instructions are not the same as shown on the TV but they worked fine for me so they may help others with a similar problem.

How to connect my Mac book Pro to a TV

How to connect my MacBook Pro to the TV using HDTV cable

I am assuming your TV has HDMI connector.
In that case, if your MacBook is the retina-one, you have HDMI connector there too. All you need is HDMI cable to connect teh two.
If your MacBook has thunderbolt port instead, you need Mini DisplayPort to HDMI adapter and HDMI cable.
Hope this makes sense.

How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

How to connect old aiport express to my new Airport Extreme?
I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
My Ipad says "base station e5713b cannot be configured."
I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
Sigve

Hi
Thanks for Swift reply.
Yep - I in fact have two A1088 and one A1264
I actually bought the new router because the Jensen
router always lost connection to the Airport Express after some hours or days. I
always needed to restart my Jensen to play music and that was driving my wife
mad. The hope was that the Extreme should fix this. Both A1088 have been set up
to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
Are the A1088 now useless?
The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
Please advise
Regards
Sigve

How to connect my iPhone and iPad to Apple TV

How to connect my iPhone and iPad to Apple TV

Connect the iPad and Apple TV to the same WiFi network. Double Tab the home button on the iPad and then swipe your recently used apps from left to right until you see the mirroring icon which looks like a retangle with an up arrow. Tab that icon until you see the Apple TV. Tab Apple TV and slide the slider to the ON position. You should now see your iPad screen on the TV the Apple TV is connected to.

How to connect my ipod to itunes if my ipod is disabled and my top button is broken

how to connect my ipod to itunes if my ipod is disabled and my top button is broken

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

How to connect my perfectly-working 20-year-old Apple Personal Laserwriter 320 to my iMac running Mountain Lion?

How to connect my perfectly-working 20-year-old Apple Personal Laserwriter 320 to my iMac running Mountain Lion?
Thank you, Morty S.

I have a perfectly-working LW 4/600 with exactly the same issue. They use localtalk - a long obsolete network connection, that doesn't connect to modern networks, and appletalk as the comm protocol.
I think the only choice you have is to use an old powerPC Mac as print server. You tell me which old Mac you have, with a localtalk connector, or that runs OS X 10.4 or earlier (so it speaks appletalk), and I'll tell you how I've done it for the past 11 years or so.
Right now I use a G4 running 10.4.11, plus an etherMac ethernet to localtalk adapter.
Before, I used a PMac 6100 running LPD server software.

How to connect my phone with the cloud

How to connect my iphone to the cloud so I can download Itunes

Do you have an Apple ID, and are you signed in, go into your settings>iCloud to check. You shouldn't need to download iTunes because that app is on your iPhone, could you give me more information of what you are trying to download.

How to connect my guitar into my new 13'' macbook pro using headphone's port?

how to connect my guitar into my new 13'' macbook pro using headphone's port?

you need a standard guitar cable and a 1/4 inch to 1/8 inch adapter such as this http://www.amazon.com/Recoton-CW1521-4-Inch-8-Inch-Adapter/dp/B00006HOIW

How to connect MB battery to +- ?

Similar Messages

Maybe you are looking for